Professional Documents
Culture Documents
Electrical Interview Question
Electrical Interview Question
View Question
View Question
How do we select a cable for a machine as per standards. Is there is any standard to select a cable
How do we select a cable for a machine as per standards. Is there is any standard to select a cable
as per voltage, or as per KVA and as per amps ratings?
Asked by: karthik
Universal Motor
What is universal motor?
Asked by: samarjuele
DC supply to Transformer
Why the transformer will burn if DC supply is given?
Asked by: harry4u
For an 100kw generator, only 50kw of load is connected. will the generator generate only 50kw
or 100kw.
For an 100kw generator, only 50kw of load is connected. will the generator generate only 50kw
or 100kw. if it generate 100kw what happens to rest of the 50kw. what happens if we connect
more than 100kw of load?
Asked by: vinesh
1. what is the different between CGS system and MKS system? 2. When we connect the
capacitor Banks in Series with the circuit 3. What is the difference between Earthing &
grounding 4. how much voltage
Asked by: kathyayini
View Question
Induction Stove
As all we know,induction stove works on the principle of electromagnetic induction.Thus an emf
is induced in the vessel and eddy current flows through the vessel.Since the vessel is made of
ferromagnetic
Asked by: SURAJTHEGREAT
View Question
View Question
View Question
Transformer Principle
Explain the transformer principle in terms of induced e.m.f. resulting from changing flux
linkages?
Asked by: khanz2012
View Question
Quiescent Point
What is a Quiescent Point (commonly called a Q-point)?
Asked by: ssmith63
View Question
Power Consumption
A heater of 1500w, bulb of 100w & 40w are connected respectively as sequence as stated above
across supply. What effect will be observed on illumination/power consumtion of all of them?
Now sequence is
Asked by: Harish P. Girhe
Phase Identification
In a three phase system three wires are of colour red, yellow and blue are used to discriminate
each phase. Now how will you identify each phase wire without knowing the colour and without
any pre information?
Asked by: elexengg
What is a Transducer?
Asked by: reddy_praveen
What is the power ratio between power in Star and Delta circuit?
Asked by: v.sudhir
Best Answer:
Wow guys what happened? Never give wrong info guys. Total Power remains the same.
Irrespective of the type of connection Power remains same. Imagine that u loose 1/3 of the
power for every Y-delta T.F. Dont Joke pa.
If u need explanation then will reply
Fan Condensers
Why condensers are used in fans?
Asked by: sjonathan
Power Factor
Alternators
Which slots does a stotor of an alternator rarely uses?
Asked by: manilal.r
Line Wire
When we touch the line wire or supply wire we get shock. What is that? Is it voltage or current or
something else?
Asked by: ips302
Wattmeter Circuit
Why pressure coil is named so in wattmeter circuit?
Asked by: aditya saxena
Power Measurement
Why current coil and pressure coil of wattmeter is connected in different phases for reactive
power meaurement?
Asked by: Harish P. Girhe
Dielectric Strength
What is dielectric strength?
Asked by: LAXMIDHAR MAHARANA
AC Generator
To induce EMF, either field has to rotate or rotor has to rotate. In Alternator, AC supply is given
to the armature to produce rotating magnetic field. The rotor is rotated by the prime mover. Then
how
Asked by: Dhivyabharathi
DG Set Tripp
What will you do when D.G. set gets tripped?
Asked by: ips302
Power Plant
What is the processing of power plant and what are the equipment used for coal handling power
plant?
Asked by: narendra982
Reactive Power
How much reactive power does a generator of rating 3.5MW generate?
Asked by: geek_srinu
Motor Vibration
What can be the possible causes of Vibration in HT motors?
Asked by: harryb63
Lightening Arrestor
Calculate the length and the distance coved by the lightening arrestor to be installed above 20
feet height industrial building.
Asked by: MAHENDRANN
View Question
Is it possible for a feedback surge to travel over a wireless connection? Would the answer be
different
Is it possible for a feedback surge to travel over a wireless connection? Would the answer be
different in a vacuum?
Asked by: xenophon
What are the technical reasons for soaking transformers for various times before allowing them
to pick
What are the technical reasons for soaking transformers for various times before allowing them
to pick load after a fault or maintenance outage or as a new installation.
Asked by: Professor
Series Connection
If 100w & 50w bulb connect in series and if we supply 440v then what happen, which one glow
first?
Asked by: ummeshraajwade
DC Generator Brush
Why the brush is fitted in M.N.A axis? What is its effect on speed?
Asked by: LAXMIDHAR MAHARANA
View Question
Phase Advancer
Why Phase Advancer is not used in below 200kva machine?
Asked by: LAXMIDHAR MAHARANA
View Question
What is the purpose of calculating knee point voltage for Current transformers?
Transformer
What happens to the power factor of a transformer when the input voltage exceeds the rated
voltage? Will it increase or decrease? Give explanation.
Asked by: rajakumar1985
DC Voltage Frequency
What is the frequency of DC Voltage?
Asked by: sintayew
Transformer Humming
What causes transformer humming?
Asked by: zmaster4all
Phase Usage
Why and when we use single phase and three phase?
Asked by: soniaraihan
View Question
View Question
View Question
Relation between mutual flux , useful flux & Power factor of a Transformer.
If mutual flux is 1.2 Wb, power factor if 0.8 lag, then what is the useful flux of a Transformer?
Asked by: Balu4u
View Question
Induction Motor
In single phase induction motor, what is phase? what is induction? Why only this motor used in
fans?
Asked by: sjonathan
Quality Factor
What is the importance of quality factor in resonance?
Asked by: shokeen
Water Level Sensor
What sensor is used to measure the level of water in a tank?
Asked by: azmat ali
Reactive Power
What is mean by reactive power? How it is generated?
Asked by: Abhijit_atrangi
Distribution Tower
What types of tower & pole is used in power system distribution?
Asked by: ummeshraajwade
Phase Conversion
List various methods to convert 1 phase to 3 phase.
Synronizing Degree
In which degree synronizing has to be done in a 3 phase alternator?
Asked by: sureshbhosale
DC Voltage Control
How we can step-up or step-down the DC voltage directly?
Asked by: kumar4486
Current Transformer
Explain why the secondary terminal of current transformer should not be lift open circuited.
Asked by: auazar
Transformer Taping
Why tapings of Transformer is always provided on HT side? why not on LT side?
Asked by: zaheerdahri
Spark Plug
When the power supply cable got sparked, it gets burnt or caches fire then explain why the spark
plug in our automobiles never get burnt or catch fire even it spark's?
Asked by: ips302
Bulb Power
The bulb has a rating of 500W for 220V, if the voltage is 110V, What is the power of the Bulb?
Asked by: balagct
Voltage Levels
Why all voltage level are multiples of 11, like 220V, 440V, 1100V instead of 200V, 400V,
1000V?
Asked by: dhands
Earth has the constant potential so we take it as reference.but in steo & touch voltage we use to
calculate
Earth has the constant potential so we take it as reference.but in steo & touch voltage we use to
calculate voltage of ground in 30 inch. How it is possible if no current can flow through ground?
Asked by: shital tikare
Power Distribution
How much load is required to convert 100 KW Single Phase load to 3 Phase Load?
Asked by: kumar_nhpc
How much voltage is present in neutral resistance?and how much voltage is present in earth
resistance
How much voltage is present in neutral resistance?and how much voltage is present in earth
resistance
Asked by: rohitasruti
Best Answer:
Actually there is no volt during normal condition. In case of any fault resistor will act as a low
resistance path. because above mentioned components are high impedence components. so the
huge fault (volt) will be grounded and the equipment remains safe.
Answered by: abbasanwarali
Read answers (2)
Transformer OC Test
Why OC test is conducted on low voltage side?
Asked by: govardhanratna
Neutral Point
Why neutral point is not required in high transmission line?
Asked by: vijay dani
Vector Group
What is vector group of transformer? Why is it required?
Asked by: sohel_rana0303
View Question
DG Set
What do you do if your DG Set is not taking load?
Asked by: ips302
View Question
Earthing Standards
What is the standard for Cable sizing & Voltage Drop?What is the standard for earthing?
Asked by: gvgnanavel
Change in Frequency
Why do we maintain 50hz frequency? What happens when we change this frequency to any
other value?
Asked by: anil.yelamarthi
3 Phase Motor
How can we test a 3 phase motor on single phase supply?How can we run a 3 Phase Motor on
Single Phase supply for testing?How can we verify of a 3 phase motors' 6 wire & name them
a1/a2/a3..b1/b2/b3
Asked by: mani777
Inductive Loads
Why does inductive loads consume KVARs?
Asked by: towhid
Alternator
Why alternator is operated at lagging power factor? How alternator responses with changing the
load?
Asked by: singhamit
Transformer Signal
Insulation Value
What is the thumb rule for insulation value in bus bars, phase to phase and phase to earth for 11
& 33 kV system?
Asked by: PK Sinha
Corona Effect
What is corona effect ? How this is avoided in transmission?
Asked by: veerateja
PF Card Function
A powerplant has 8 gensets operating in grid parallel mode. In one genset sometimes there is pf
variation and kvar variation. The plant operates in pf mode. When this variation is observed the
load is
Asked by: rupesh2k3
View Question
View Question
Earthing Resistance
What will be the body impedance of human body>What will be the maximum allowable earthing
resistance value?
Asked by: rajakumar1985
View Question
Power Factor
A powerplant has 8 gensets operating in grid parallel mode. In one genset sometimes there is pf
variation and kvar variation. The plant operates in pf mode. When this variation is onbserved the
load is
Asked by: jigs_eee
What is thyristor?
Asked by: santhoshreddy
When we increse load , current drawn from source also increses why ?
Asked by: Rakesh Sable T.I.T. Bhopal
In a synchronous motor armature current flows due to revolving flux which in turn rotates the
load,but
In a synchronous motor armature current flows due to revolving flux which in turn rotates the
load,but in no load condition armature current is zero hence thr is no revolving flux then how
motor rotates? pls give books referance.
Harmonics Deduction
How can we control or deduct harmonics?
Asked by: vipin_rajput1
Main Switch
What the name given for to connect the main switch supply to the various appliances?
Asked by: f.mike
Two electrically operated Vibro Motors are fixed in parallel direction in vibrating feeder. What is
the direction of both Vibro Motors?
Asked by: rajinippp
Potential Transformer
What is the function of a potential transformer?
Asked by: towhid
View Question
View Question
Phase Advancer
Explain What is Phase Advancer?
Asked by: daneeyarr
EM Waves
When the operating wavelength of line is /4
Asked by: chaitugeek
View Question
Synchronous Machine
We know synchronous machine run at a constant speed.Consider Synchronous motors, If you
load the machine, will the speed reduce? If it does so, then it prohibits the property of
synchronism. So Explain
Asked by: SURAJTHEGREAT
Core cables
generally we are using 4 core or 3.5 core cable for power supply ,in this practice we are
connecting three different phase R,Y,B and Neutral to our 4 core or 3.5 core cable,but for our
termination conveniences
Asked by: jatin patel
Network Synthesis
Why the roots of the network function are +ve?
Asked by: papu150
3 Phase Motors
Why do 3 phase motors rotate in the opposite direction when any two phases are interchanged?
Asked by: Oladele olajide
Power Lines
In an AC transmission line(3 phase), If there is a short between any two phases. How will you
determine this fault on a protection relay. what will your wave forms look like?
Asked by: jabbaa
View Question
View Question
Nanotech Applications
Name some of the application of nanotech in field of power enggineering.
Asked by: G.N.Akhil
View Question
Phase Sequence
What happens when we change the phase sequence in 3 phase system?
Asked by: full61
What are the general preparations a candidate should do before attending the inteview
Asked by: abhishekmaharaja
LV Switchgear
Considering the short circuit fault, which switchgear is preferable, SFU OR MCCB? Which
operates faster? which one is popular in Indian Market and why? 2) Define SCPD. What is type2
co-odination? 3)
Asked by: jayashreeraut
View Question
View Question
Nano Technology
What is the application of Nano Technology in the field of electricals?
Asked by: G.N.Akhil
View Question
View Question
View Question
Flowmeter
What are the flowmeter?
Asked by: ayman sultan
View Question
SC Test
Voltage Source
What would happen if two voltage sources of different magnitude are connect in parallel?
22 KV Cables
What are the maximum number of joints you can make in a (3x300mm, 22KV) cable over +/610m?
Asked by: PRINS
Cable Selection
What is the max current rating for a 4 core * 1mm^2 cable?
Asked by: praveerkumardas
Purpose of Earthing
What purpose does an earth serve on a generator terminals if the generator was started
accidentally.This a true incident when the generator was started it blew the earth wire because
the terminals were
Asked by: sukhasingh
Form Factor
What is the link between Voltage and Form Factor?
Asked by: rajsekhar240
Does the stator of the Induction machine consume only reactive power? If this is the case, so
where does the active power in the rotor come from? Explain.
Asked by: Ereiba
Alternator capacity
Is it possible to increase the capacity of a synchronous generator upto 30% to 50% just to modify
the cooling system but the other component remain same? Explain
Asked by: KAUSHIK DEB
Alternator Regulation
Why most of the alternator is connected in star and have high regulation around 30% as
compared to transformer?
Asked by: Singh Amit
Hysteresis Loss
What is the effect of hysteresis loss in transformer/machines especially in DC one?
Asked by: shiney07
Belt Weigh Feeders
What is the caliberation procedure and its requirement of belt weigh feeders?
View Question
Power Generation
What measures will take for cost saving in utility and power generation
Asked by: mtallhaishfaq
View Question
Power House
Describe briefly about key functions of Utility and Power House.
Asked by: mtallhaishfaq
View Question
Capacitor Banks
What is the best method to connect two capacitor bank?
Circuit dynamics
How do we solve for poles and zeros in a circuit dynamics
Asked by: Oladele olajide
View Question
Transformer Capacity
If the capacity of a Transformer is 20/26 then what does 20/26 shows? what is its purpose?
Asked by: zaheerdahri
Power Factor
What is Power Factor? How it is calculated?
Asked by: jangra gautam haluwas
Voltage Drop
How to can calculate voltage drop in a cable?
Asked by: mpanwar
Transformer rating
Why do we rate transformer in KVA not in KW?
Asked by: Sajjad Hussain Turi
Capacitor Connection
Why the capacitors are connected in delta? What advantage it having than star connection?
Asked by: rajakumar1985
View Question
Neutral ct
Why do we use neutral ct in a transformer?
Asked by: karthik electrical
What is the voltage drop for 100kw motor if the length of the cable is 200m and what is the cable
size.
What is the voltage drop for 100kw motor if the length of the cable is 200m and what is the cable
size.
Asked by: srinivas
Motor Frequency
Motor manipulator detail is 230v 50hz frequency. If you increase frequency what will happen?Is
there any need for coil protection?
Asked by: jayakumar.eie02
Induction Generator
Is it possible to run the induction generator only with the inductive load (without the use of
capacitors for supplying the reactive power)? Explain
Asked by: rajakumar1985
Floting Earth
What is meant by Floting Earth? What will happen if we use regular earthing instead of floting
earth and Where do we have to use only floting earth.
Asked by: rahul_penshanwar
Wattage related to Frequency
A motor rated 230V, 50HZ taking 100KW no load amps, what happen if just frequency goes to
60Hz?
Asked by: PRADYUT SINHA
View Question
Transformer Sound
Why do you get a typical sound when the transformer is put into operation?
Asked by: lavanyaa
Alternator Operation
If we put field winding on stator and armature winding on rotor then how will it operate? Will it
rotate at synchronous speed or not? (Assuming that the alternator is feasible)
Asked by: shobhit bansal
3 Phase Motor
How can we find u1,v1,w1 and u2,v2,w2 in three phase motor when operating in delta as we
have on identification on motor lead which comes out from winding.
Asked by: arypandya
Induction Motor
Why star point of star connected motor is not grounded?
Asked by: singhamit
Circuit Breaker
Which Circuit Breaker is better either Air CB or Vacuum CB? Why?
Asked by: Abhijit_atrangi
Use of DC machine
We have enough category of AC machines more relliable than DC machine then why we are
using DC machines in some application yet?
When there is a sudden loss in the demand what happens to the transformer and generation?
Asked by: kAVITA
Best Answer:
When there is a sudden loss of load, The Generator terminal voltage increases due to the fact that
the IX drop in the generator winding decreases. The EMF generated being the same the reduced
reactance loss leads to a sudden rise in generator voltage..but the AVR (Automatic Voltage
Regulator) will act instantly to bring this voltage to the set value by reducing the excitation.
There is practically no effect of this on the transformer barring the reduction in I2R (copper
Circuit Breaker
Does HVDC mode of transmission has an economic advantage over EHV-AC transmission.
Justify
Asked by: Anandkumar
3 Phase
Why there is 220v in 1-phase but 440v in 3-phase?
Asked by: arpan singh
Insulation Value
What is the thumb rule for insulation value in bus bars, phase to phase and phase to earth for 11
& 33 KV system?
Asked by: muhammad malik
View Question
LT Panels
What are the various types of LT panels? Name them.
Asked by: jayashreeraut
Voltage Standing Wave Ratio
List the basic ways of determining the voltage standing wave ratio in a transmission line.
Asked by: kiss_of_death_2010
View Question
View Question
Power Factor
What is the power factor?
Asked by: rupeshpotdar
Circuit Breaker
View Question
What is the effect of pole slipping in generator and how it will slip?
Asked by: G.shreeshail
60Hz Transformer
What would happen if a transformer is made to operate at 60Hz instead of 50Hz ?
Asked by: technoholixstallion
Motor Starting
The single phase induction motor starts with two phases(Using capacitor). Why can't the three
phase induction motor starts with two phase?
Asked by: rajakumar1985
View Question
View Question
View Question
Save Power
Suppose the electricity board gives 11 kw, but the machine requires only 8 kw in such case how
can we save the excess power?
Asked by: kumar4486
Q Points
What is the importance of 'Q Point' in transistor's load line analysis?
Asked by: srbhsamir
View Question
Lightening
Does lightening contain voltage or current, Explain.
Asked by: mallick.subratkumar
Capacitor Banks on DG
Why many people not connect the APFC/Capacitors in DG circuit?
Asked by: Pavankumar_reddy5
Excessive Power
How can we make use of excessive power efficiently?
Asked by: kumar4486
Form factor
What is mean by form factor of the AC current?
Asked by: Abhijit_atrangi
APFC/Capacitors in DC circuit
Why many people do not connect the APFC/Capacitors in DC circuit?
Asked by: praveen goyal
Phase Shifting
Why do we use phase shifting at Current Transformer?
Asked by: INFO_3D
Current Circulation
Is it possible if their is no voltage then their is no current circulation or does it depend on circuit
condition?
Asked by: Abhijit_atrangi
Power Factor
Why the Voltage rises when Leading Power Factor is occurs?
Asked by: Pavankumar_reddy5
Sub-Station Label
Why the Substaions are labled as 11KV/33KV or 66/11KV etc instead of label with the POWER
TRANSFORMERS Rating (In MVA/KVA)?
Asked by: Pavankumar_reddy5
Lightening Arrestor
Location of lighting arrestor should be near transformer or not? Why?
Asked by: Renukrishnan
Transformer Rating
How to identify Transformer rating without Name Plate details?
Asked by: Pavankumar_reddy5
Conductor Size of Fuse and Cable
For 63A load we can use 25/35sqmm cable. For same rating fuse conductor size is too low. How
is it possible?(Its not depends on meterial, because single strand for above cable size is enough
for fuse)
Asked by: sankaran.p
Power System
Why the transmitted voltage is multiple of 11 like 11, 22, 33, 132 etc? Is their any technical
reason for that?
View Question
Voltmeter Measurement
If we connect a voltmeter between earth and ground wire, how much it will measure?
Asked by: elexengg
BusBar
What is a busbar?
Asked by: brijesh_balu
Wattmeter
Wattmeter has two coils in it-the current coil & pressure coil, why is the pressure coil so named?
How is the power being measured by the Wattmeter?
Asked by: fishu
Induction Motor
Why transformer does not rotate like induction motor. Inspite both having same principle?
Asked by: ravi.dcrust
Synchronous Generator
How and when synchronous generator acts as a synchronous condenser?
Asked by: kartheear
Tripper Drops
Consider you have a tripper at your house. The instant you switch on your motor, the tripper
drops. What could be the problem?
Asked by: SURAJTHEGREAT
Wattmeter reading
Why does wattmeter's reading go negative?
Asked by: munish1983
PID control
Give brief detail on PID Control.
Asked by: gautam jangra
Magnets in Speaker
Neutral Earthing
What is neutral earthing and equipment earthing?What are the advantages of grounding a neutral
of a transformer and gernator?
Asked by: munaam
Vector Quantity
Is current a Vector quantity? If yes, then two wires on 90 degree angle must have resulting
current equal to zero.
Asked by: vikas_loves_black59
Units Calculation
How many units will a 40W tube consume in 1hr 15 minutes 20 seconds?
Asked by: desairanjeet
View Question
Skin Effect
What do you mean by skin effect?
Asked by: raniagamal
Electrostatic Power
Is it possible to generate electrostatic power? If yes, how?
View Question
View Question
Earthing Resistance
What is Earthing Resistance?
Asked by: mahesh_rathod
Generator Breakdown
What are the major causes of a generator breakdown?
Asked by: emmanuel ajiwaye
What is a u.p.s
Asked by: p dehury
How much should be the insulation resistance value of a 5KW motor and 50KW motor?
Asked by: vijaykumardas
View Question
Inductive Load
How to design inductive load for 3 phase 440v and maximum 5 amps for star or delta?
Asked by: Kelley Yoedren
How do you detect the exact location of a cable fault if its cable puncture
Asked by: anand sinha
Power Factor
The power is -ve for the first 2ms and then it will -ve What will be the P.F. Angel?
Asked by: jaydeepmodi
View Question
DC Circuit in AC MCB
Does using a AC MCB in a DC circuit affect the tripping time or the perfromance?
Brush Alternator
What is a brush alternator?What is a brushless alternator?What is the difference between brush
and brushless alternator?Which is better between brush and brushless alternator?
Asked by: sayeed5218
Voltage Drop
How to calculate the voltage drop in cable?
Asked by: karthik electrical
Harmonics
How harmonics are produced in m/c what is its physical significance?
Asked by: tiwarianjanikumar
Motor Rating
Can we use a 15kW, 1450rpm motor for 15kW, 960rpm apllication?If yes, what will be the
drawbacks?
Asked by: ibicelectrical
VFD Testing
Can you test a VFD panel with Resistive load banks? If Yes, How?
Asked by: chrischang
View Question
Motor starters
When is star-delta, Dol or VFD starters used for the motor? How many times the current rating
of the motor wil be drawn on a Dol starter if no OLR used?
Asked by: karthik8823
Electrical Transducer
What is the fuction of electrical current transducer, voltage transducer in control panel?
CT accuracy
How to calculate and manufacture the 5P20 class CT with require knee point volt?
Asked by: abbasanwarali
View Question
Inductive Load
How to design inductive load for 3 phase 440v and maximum 5 amps for star or delta?
Asked by: SENT2008
View Question
PNPN Thyristor
Why PNPN is used as thyristor NPNP is not used?
Asked by: suryapraba6
Sine Wave
Why we use sine wave in supply system rather than square and triangular wave?
Asked by: amith.n.n
Motor
what is the testing of h.t and l.t. motors before erection and commissioning?
Asked by: kumar_rakesh02
PLC
What is PLC? Outline its working Principal.
Asked by: jangra gautam haluwas
Transmission Line
What is Transmission Line? How it is used? Give examples.
Fuse Rating
Dear AllI wan to know that we are using large type of cable like 300sqmm and other and our
load also in much kw but we are using a small type fuse in main supply (not HT Side) how can it
bear load.
Asked by: jkamboj
Cable selection
Why Cable selection depends on Load current? (UG Cables & OH lines)
Asked by: eeemalik
DC Machine as Generator
It is possible to run one DC machine as a generator or motor purposely? What adjustment we
have to do for that operation?
Asked by: Abhijit_atrangi
Traction System
What do you mean by traction system, What type of traction system is used in electric train.
AC Drive
How does a AC drive work? Why does not AC motors blow up when testing dead short but it
would if you put DC on it?
Asked by: benkeny
View Question
Why the generators are made such that they generate only sinusoidal wave?
Asked by: srishiva
Magnetic Levitation
What is Magnetic Levitation ?How MAGLEV (Trains based on Magnetic Levitation) works ?
Asked by: rohansharma
View Question
Coupling Capcitor
What is the purpose of coupling capacitor?
Asked by: chinnakalupukuri
Q-point in transistor?
What is the purpose of Q-point in transistor?
Asked by: chinnakalupukuri
Capacitive Load
Why we cannot use the capacitive load?
Asked by: thicman101112
DC & AC motor
Whats happens when we give DC to a induction motor
Asked by: hariomprajapat
What is the instataneous value of voltage in a 3-phase balanced star connected circuit?
Asked by: sudhir
Why people say that "When we want to send information (transfer from one pont to another) we
modulate
Why people say that "When we want to send information (transfer from one pont to another) we
modulate the signal below or obove the center point (reference point)?1) By modulation we
mean what?2) Why it is neccassary to modulate signal for information center.3) Why more the
modulation more inforamation can be send?
Asked by: rana_m_zeeshan
View Question
View Question
View Question
What is watt?
Asked by: nipmhimt
I want to measuring distance with laser diodeand I bought sld65018371 from samsung
semiconductor please
I want to measuring distance with laser diodeand I bought sld65018371 from samsung
semiconductor please help me how can I use my laser or a similar model regard
Asked by: kamyar navid