Professional Documents
Culture Documents
Renault Trim Removal
Renault Trim Removal
"The repair methods given by the manufacturer in this document are based on the All copyrights reserved by Renault.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part
The methods may be modified as a result of changes introduced by the manufacturer reference numbering system is forbidden without the prior written authority of Renault.
in the production of the various component units and accessories from which his
vehicles are constructed."
© RENAULT 2002
Trim and
upholstery
Contents
Page Page
Edition 2
171ABODY INTERIOR TRIM
A-pillar trim 71A A
REMOVAL IMPORTANT:
The frame seals should be handled carefully to avoid
any risk of damage or marking.
Release:
– the clip (B),
– the sun visor.
71A-1 Edition 3
BODY INTERIOR TRIM
A-pillar trim 71A A
REFITTING
IMPORTANT:
The Carminat system aerial wire is attached to the left-
hand windscreen pillar mounting clips.
71A-2 Edition 3
BODY INTERIOR TRIM
B-pillar lower trim 71A B
REMOVAL
REFITTING
71A-3 Edition 3
BODY INTERIOR TRIM
B-pillar upper trim 71A C
REMOVAL (5-door version)
REFITTING
71A-4 Edition 3
BODY INTERIOR TRIM
B-pillar upper trim 71A C
IMPORTANT:
For a vehicle fitted with rear side airbags, before
removing the rear wing trim it is essential to lock the
airbag computer using the diagnostic tool (see
Section 88C).
71A-5 Edition 3
BODY INTERIOR TRIM
B-pillar upper trim 71A C
REFITTING
Release:
– the trim (3) and (4),
– the seat belt strap through opening (D).
71A-6 Edition 3
BODY INTERIOR TRIM
Front door sill lining 71A D
REMOVAL (3-door version) REMOVAL (5-door version)
71A-7 Edition 3
BODY INTERIOR TRIM
Rear door sill trim 71A E
REMOVAL Unclip lining (3) and (4).
Remove:
– the bench seat squab,
– clip (A) using an unclipping tool.
71A-8 Edition 3
BODY INTERIOR TRIM
Rear door sill upper trim 71A F
REMOVAL Move the seat forwards.
IMPORTANT:
For a vehicle fitted with rear side airbags (see
illustration below) before removing the rear wing trim
it is essential to lock the airbag computer using the
diagnostic tool (see Section 88C).
71A-9 Edition 3
BODY INTERIOR TRIM
Rear door sill upper trim 71A F
REFITTING
71A-10 Edition 3
BODY INTERIOR TRIM
Rear wing trim 71A G
REMOVAL
IMPORTANT:
For a vehicle fitted with rear side airbags, before
removing the rear wing trim it is essential to lock the
airbag computer using the diagnostic tool (see
Section 88C).
Remove:
– the bench seat squab,
– the bolt (A).
71A-11 Edition 3
BODY INTERIOR TRIM
Rear wing trim 71A G
REFITTING
71A-12 Edition 3
BODY INTERIOR TRIM
Rear quarter panel trim (5-door version) 71A H
Move the front seat forward.
TIGHTENING TORQUE (in Nm)
REMOVAL
IMPORTANT:
For a vehicle fitted with rear side airbags (see
illustration below) before removing the rear wing trim
it is essential to lock the airbag computer using the
diagnostic tool (see Section 88C).
71A-13 Edition 3
BODY INTERIOR TRIM
Rear quarter panel trim (5-door version) 71A H
Remove the seat squab of the bench seat. Remove the seat belt lower mounting bolt (B).
71A-14 Edition 3
BODY INTERIOR TRIM
Rear quarter panel trim (5-door version) 71A H
Release:
– the trim (7),
– the seat belt strap through opening (D).
REFITTING
71A-15 Edition 3
BODY INTERIOR TRIM
Rear quarter panel trim (3-door version) 71A I
REMOVAL
IMPORTANT:
For a vehicle fitted with rear side airbags, before
removing the rear wing trim it is essential to lock the
airbag computer using the diagnostic tool (see
Section 88C).
Remove bolts (A). Unclip the front door sill trim (1).
71A-16 Edition 3
BODY INTERIOR TRIM
Rear quarter panel trim (3-door version) 71A I
Release:
– the trim (3) and (4),
– the belt strap through opening (E).
71A-17 Edition 3
BODY INTERIOR TRIM
Rear quarter panel trim (3-door version) 71A I
REFITTING
Tighten the rear seat belt and rail lower mounting bolt
to a torque of (21 Nm).
Release:
– the trim (6),
– the seat belt strap through opening (G).
71A-18 Edition 3
BODY INTERIOR TRIM
Rear end panel lining 71A J
REMOVAL
Remove:
– the bolts (A),
– the striker trim.
REFITTING
71A-19 Edition 3
BODY INTERIOR TRIM
Wheel arch trim 71A K
REMOVAL
Remove:
– the rear end panel trim (see Section 71A-J),
– the parcel shelf,
– for the 5-door version: the rear door sill upper trim
(see Section 71A-F),
– for the 3-door version: the rear wing trim (see
Section 71A-G).
Release:
– the luggage compartment seal (partially),
– the wheel arch lining.
REFITTING
71A-20 Edition 3
BODY INTERIOR TRIM
Headlining (5-door version) 71A L
REMOVAL
IMPORTANT:
Before starting to remove the headlining it is
essential to lock the airbag computer using the
diagnostic tool (see Section 88C).
Remove:
– the windscreen pillar trim (see Section 71A-A).
– the sun visors (see Section 57A-E).
Partially remove:
– the door frame seals,
– the luggage compartment seal.
71A-21 Edition 3
BODY INTERIOR TRIM
Headlining (5-door version) 71A L
Removing the rear quarter panel trim:
71A-22 Edition 3
BODY INTERIOR TRIM
Headlining (5-door version) 71A L
Tilt the bench seat squab. Remove the seat belt lower mounting bolt (E).
71A-23 Edition 3
BODY INTERIOR TRIM
Headlining (5-door version) 71A L
Unclip trim at (8). Unclip the two upper clips on the trim.
Release:
The following operations require two people.
– the trim at (9),
– the seat belt strap through opening (G).
Carefully remove the trim (Velcro strip).
Removing the grab handles:
Fit the trim on the headrest and connect the various
connectors.
Using tool Car. 1597, unclip the two mounting pins (A),
then pull it to remove.
71A-24 Edition 3
BODY INTERIOR TRIM
Headlining (5-door version) 71A L
Special notes for the removal of the headlining
fitted with a sunroof:
NOTE:
The procedure below deals only with those
components which are featured when the vehicle is
fitted with a sunroof.
The rest of the procedure is the same as that for a
model without a sunroof.
ATTENTION:
the Carminat system aerial wire is secured to the left-
hand windscreen pillar mounting clips.
IMPORTANT:
The trim must be handled carefully because cutting the
sunroof makes the two side edges more fragile (risk of
bending).
REFITTING
71A-25 Edition 3
BODY INTERIOR TRIM
Headlining (3-door version) 71A M
REMOVAL
IMPORTANT:
Before starting to remove the headlining it is
essential to lock the airbag computer using the
diagnostic tool (see Section 88C).
Remove:
– the windscreen pillar trim (see Section 71A-A).
– the sun visors (see Section 57A-E).
Partially remove:
– the door frame seals,
– the luggage compartment seal.
71A-26 Edition 3
BODY INTERIOR TRIM
Headlining (3-door version) 71A M
Removing the rear quarter panel trim:
71A-27 Edition 3
BODY INTERIOR TRIM
Headlining (3-door version) 71A M
Unclip the rear wing trim (2). Unclip the lower mounting clips (D).
Release:
– the trim (3) and (4),
– the belt strap through opening (E).
71A-28 Edition 3
BODY INTERIOR TRIM
Headlining (3-door version) 71A M
Partially release the luggage compartment seal. Unclip the two upper clips on the trim.
Using tool Car. 1597, unclip the two mounting pins (A),
then pull it to remove.
71A-29 Edition 3
BODY INTERIOR TRIM
Headlining (3-door version) 71A M
Special notes for the removal of the headlining REFITTING
fitted with a sunroof:
Insert the trim though the luggage compartment lid.
NOTE:
The procedure below deals only with those Connect the connectors.
components which are featured when the vehicle is
fitted with a sunroof. Centre the trim while fitting the grab handles.
The rest of the procedure is the same as that for a Proceed in the reverse order to removal.
model without a sunroof.
71A-30 Edition 3
BODY INTERIOR TRIM
Boot carpet 71A N
REMOVAL
REFITTING
71A-31 Edition 3
BODY INTERIOR TRIM
5-door version carpet 71A O
REMOVAL
IMPORTANT:
For a vehicle fitted with rear side airbags (see
illustration below) before removing the rear wing trim
it is essential to lock the airbag computer using the
diagnostic tool (see Section 88C).
Remove:
– the front seats (see Section 75A-A) (follow the
safety instructions),
– the central console (see Section 57A-A),
– the parking brake control (see Section 37A),
– the rear seat squab (see Chapter 76A-C).
Unclip:
– the clip (A),
– the trim at (3) and (4),
71A-32 Edition 3
BODY INTERIOR TRIM
5-door version carpet 71A O
Remove clip (A) using unclipping pliers. Pressing down the screwdriver, release the clip.
REFITTING
71A-33 Edition 3
BODY INTERIOR TRIM
3-door version carpet 71A P
REMOVAL
IMPORTANT:
For a vehicle fitted with rear side airbags, before
removing the rear wing trim it is essential to lock the
airbag computer using the diagnostic tool (see
Section 88C).
Remove:
– the front seats (see Section 75A-A) (follow the
safety instructions),
– the central console (see Section 57A-A),
– the parking brake control (see Section 37A),
– the rear seat squab (see Chapter 76A-C).
Unclip:
– the clip (A),
– the trim (2).
Unclip the front door sill trim (1). Remove the bolt (A).
71A-34 Edition 3
BODY INTERIOR TRIM
3-door version carpet 71A P
For a vehicle fitted with rear side airbags: Remove the carpet.
Tighten the rear seat belt and rail lower mounting bolt
to a torque of (21 Nm).
71A-35 Edition 3
BODY INTERIOR TRIM
Parcel shelf 71A Q
Remove:
TIGHTENING TORQUE (in Nm)
– clips (B), using a pair of unclipping pliers,
– the partition panel.
bolt (C) 8
bolt (F) 2
bolt (H) 21
bolt (J) 21
REMOVAL
71A-36 Edition 3
BODY INTERIOR TRIM
Parcel shelf 71A Q
Remove:
– bolts (G),
– the emergency spare wheel flap.
71A-37 Edition 3
BODY INTERIOR TRIM
Parcel shelf 71A Q
Release both side trim pieces. Release load stop strut (2).
71A-38 Edition 3
BODY INTERIOR TRIM
Parcel shelf 71A Q
REFITTING
71A-39 Edition 3
172A SIDE DOOR TRIMS
Front door trim 72A A
NOTE:
In the case of replacing a door or performing an
operation on the bodywork, refer to Section 47A.
REMOVAL
WARNING:
Do not pull on the glove compartment door.
72A-1 Edition 2
SIDE DOOR TRIMS
Front door trim 72A A
Remove bolts (A). Using a flat screwdriver, unclip the opening release
cable mounting cover.
Remove the cover and the bolt (B) from the door
opening handle. Unclip the lining flap with an unclipping tool (while
protecting the lining).
72A-2 Edition 2
SIDE DOOR TRIMS
Front door trim 72A A
Position the window in order to access the two Release the window.
mounting clips (C).
NOTE:
The window winder motor and the wiring harness are
attached to the trim.
72A-3 Edition 2
SIDE DOOR TRIMS
Front door trim 72A A
REMOVAL OF THE ELECTRIC WINDOW MOTOR
Unclip clip (G) and remove the "lining / window riser Disconnect the window riser motor.
motor / harness" assembly.
Unclip from the lining the four mountings of the window
operating slide.
72A-4 Edition 2
SIDE DOOR TRIMS
Front door trim 72A A
REFITTING
NOTE:
During replacement, the lining will be supplied
separately. It is therefore important to remember the
harness run.
Position the two lower bolts (I) and the upper bolts (J).
72A-5 Edition 2
SIDE DOOR TRIMS
Front door flap 72A B
REMOVAL
72A-6 Edition 2
SIDE DOOR TRIMS
Front door flap 72A B
Remove bolts (A). Using a flat screwdriver, unclip the opening release
cable mounting cover.
Remove the cover and the bolt (B) from the door
opening handle. Unclip the lining flap with an unclipping tool (while
protecting the lining).
REFITTING
72A-7 Edition 2
SIDE DOOR TRIMS
Rear door panel lining 72A C
NOTE:
In the case of replacing a door or performing an
operation on the bodywork, refer to Section 47A.
REMOVAL
Remove the cover and the bolt (A) from the door
opening handle.
72A-8 Edition 2
SIDE DOOR TRIMS
Rear door panel lining 72A C
72A-9 Edition 2
SIDE DOOR TRIMS
Rear door panel lining 72A C
REFITTING
NOTE:
During replacement, the lining will be supplied
separately.
It is therefore important to remember the harness
routing.
72A-10 Edition 2
SIDE DOOR TRIMS
Rear door panel lining 72A C
Fit:
– the lower bolt (F) and the upper bolts (I),
– the bolts (J).
72A-11 Edition 2
SIDE DOOR TRIMS
Rear door flap 72A D
NOTE:
In the case of replacing a door or performing an
operation on the bodywork, refer to Section 47A.
REMOVAL
Remove the cover and the bolt (A) from the door
opening handle.
REFITTING
72A-12 Edition 2
173A
NON-SIDE OPENING ELEMENT TRIM
Bonnet trim 73A A
REMOVAL
REFITTING
73A-1
NON-SIDE OPENING ELEMENT TRIM
Tailgate trim 73A B
REMOVAL
NOTE:
If the rear seat retaining pin is faulty, it is available
separately as a replacement part and can be replaced
on its own.
73A-2
NON-SIDE OPENING ELEMENT TRIM
Tailgate trim 73A B
REFITTING
73A-3
175A
FRONT SEAT FRAMES AND RUNNERS
Whole seat 75A B
Seat bolts 35
IMPORTANT:
Before starting any work on the airbag system, lock
the computer using the diagnostic tools (see
Section 8).
IMPORTANT:
It is not permitted to handle the pyrotechnic systems
(airbags and pretensioners) near a source of heat or
flame as there is a risk of triggering.
REMOVAL
Protect:
– the front door sill lining,
– the carpet. Move the seat to the forward position.
75A-1 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Whole seat 75A A
REFITTING
IMPORTANT:
Respect the order of tightening of the seat bolts.
Tighten:
– the rear bolt (A) towards the inside of the vehicle,
– the front bolt (B) towards the inside of the vehicle,
– the rear bolt (C) towards the outside of the vehicle,
– the front bolt (D) towards the outside of the vehicle.
Tighten to torque.
75A-2 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
M8 bolts 25
M10 nuts 66
IMPORTANT:
Before starting any work on the airbag system, lock
the computer using the diagnostic tools (see
Section 8).
Unclip the seat booster cushion handle using a flat
screwdriver.
IMPORTANT:
It is not permitted to handle the pyrotechnic systems
(airbags and pretensioners) near a source of heat or
flame as there is a risk of triggering.
REMOVAL
Remove:
– the seat (see section 75A-A),
– the headrest.
DISMANTLING
75A-3 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
Adjust the seat cushion to high position (spring Remove the headrest guide caps (F).
extended to the maximum).
Detach the seat cover from the headrest guides.
Remove:
– the height adjustment mechanism rivets (C),
– the mechanism and the control.
75A-4 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
Remove the lumbar support adjustment tumblewheel Remove housing screw (G).
mounting cover, using tool Car. 1597.
Detach the housing.
75A-5 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
75A-6 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
IMPORTANT:
Carefully release the cover, holding the velcro strips
on the foam pad, in order not to damage the
seatback foam.
75A-7 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
75A-8 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
IMPORTANT:
Carefully detach the cover, holding the velcro strips
on the foam pad, in order not to damage the seat
cushion foam.
75A-9 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
75A-10 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
IMPORTANT:
Insert a metal pin across the frame through the
opening (A), strap it in place if necessary.
Check that it is secure before carrying out any work.
Unclip:
– the cover,
– the cable stops (R).
For a seat squab cushion height adjustment
mechanism replacement operation:
The spare part comprises the height adjustment Remove the bolts (B).
mechanism and the control.
Method: IMPORTANT:
– it is not necessary to remove the return spring, Keep the pin in place during removal.
– adjust the seat cushion to the high position (spring
extended to the maximum),
– drill out the three rivets (S),
– remove the mechanism and the control,
– clean the shaft splines.
75A-11 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
Remove:
IMPORTANT:
– the bolts (C),
Do not remove the plastic clips at (C).
– the seatback frame.
Check that it is secure before carrying out any work;
if in any doubt, insert a pin through the parts of the
REFITTING
frames (C).
Adapting the spare part to replace the seatback frame
on a 5-door version seat: Pre-tightening and tightening the frame mountings:
– the spare seatback frame is a version C frame
(3-door), – pre-tightening the three M10 nuts to 20 Nm,
– it is necessary to cut the door side plate for the – pre-tightening the two M8 bolts,
seatback unlocking mechanism (see below). – tighten the M10 nuts to a torque of 66 Nm,
– tighten the M8 bolts to a torque of 25 Nm.
Tighten to torque.
75A-12 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
Special notes on the 3-door version
75A-13 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Front seat frame 75A B
REFITTING
IMPORTANT:
before refitting the seatback cover, check that the
velcro strips are properly fastened to the seatback
foam.
Unclip the cable stops.
75A-14 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Seat runners 75A C
Seat bolts 35
IMPORTANT:
Before starting any work on the airbag system, lock
the computer using the diagnostic tools (see
Section 8).
IMPORTANT:
It is not permitted to handle the pyrotechnic systems
(airbags and pretensioners) near a source of heat or
flame as there is a risk of triggering.
REMOVAL
Unhook the seat belt by pressing on latch (A). Move the seat to the rearmost position.
75A-15 Edition 2
FRONT SEAT FRAMES AND RUNNERS
Seat runners 75A C
Disconnect the connector under the seat. Remove the three nuts (C).
IMPORTANT:
Respect the order of tightening of the seat bolts.
Tighten to torque.
75A-16 Edition 2
REAR176A
SEAT FRAMES AND RUNNERS
Complete seatback 1/3 / 2/3 76A A
Tightening torques
REMOVAL
NOTE:
For easier access to the seatback mountings, remove
the seat squabs.
The 1/3 and 2/3 seatbacks can be removed separately.
Remove:
– the belt bolts (A),
– the front seatback bolts (B).
76A-1 Edition 2
REAR SEAT FRAMES AND RUNNERS
Complete seatback 1/3 / 2/3 76A A
REFITTING
Tighten to torque.
76A-2 Edition 2
REAR SEAT FRAMES AND RUNNERS
Locking the seatback 76A B
Tightening torques
REMOVAL
76A-3 Edition 2
REAR SEAT FRAMES AND RUNNERS
Locking the seatback 76A B
REFITTING
Torque tighten.
76A-4 Edition 2
REAR SEAT FRAMES AND RUNNERS
Complete seat squab 1/3 / 2/3 76A C
REMOVAL
NOTE:
Removal is the same as for a 1/3 seat, a 2/3 seat and
a 1/1 seat.
Release clip.
REFITTING
Tilt the seat squab and unclip it.
Make sure the clips are in good condition before
refitting the seat squab.
76A-5 Edition 2
REAR SEAT FRAMES AND RUNNERS
Seatback frame 76A D
Tightening torques
REMOVAL
76A-6 Edition 2
REAR SEAT FRAMES AND RUNNERS
Seatback frame 76A D
REFITTING
Use tool Car. 1558 (Blue) for the headrest zip fastener
(see Section 78A-A).
Torque tighten.
76A-7 Edition 2
177A FRONT SEAT TRIMS
Seatback trim 77A A
REMOVAL
Remove:
– the seat (see Section 75A-A) (follow the safety
guidelines),
– the headrest.
77A-1
FRONT SEAT TRIMS
Seatback trim 77A A
Special notes on the 3-door version seat
Remove:
– handle screw (C),
– handle trim screws (D).
77A-2
FRONT SEAT TRIMS
Seatback trim 77A A
Using a screwdriver, remove the lumbar support Unclip the cover clips at the airbag.
adjustment tumblewheel.
77A-3
FRONT SEAT TRIMS
Seatback trim 77A A
Remove the cover retaining sections (H). Remove the foam pad taking care at the headrest
guides to avoid any damage.
WARNING
Carefully release the cover, holding the velcro strips
on the foam pad, in order not to damage the
seatback foam.
REFITTING
Carefully remove the seatback cover at the headrests. Proceed in the reverse order to removal.
WARNING
Before refitting the seatback cover, check that the
velcro strips are properly fastened to the seatback
foam pad.
77A-4
FRONT SEAT TRIMS
Seat cushion trim 77A A
B
REMOVAL
Remove:
– the seat (see Section 75A-A) (follow the safety
guidelines).
77A-5
FRONT SEAT TRIMS
Seat cushion trim 77A A
B
Remove the seat booster cushion adjustment Release the lower retaining rubber bands from the
mechanism rivets (C). seatback cover.
Remove the mechanism and the control. Unclip the cover back support clips (E).
77A-6
FRONT SEAT TRIMS
Seat cushion trim 77A A
B
WARNING
Carefully release the cover, holding the velcro strips
on the foam pad, in order not to damage the seat
cushion foam.
Remove:
– the seat cushion cover,
– the foam pad.
Release the cover retaining section (I). Remove the cover clips (J).
REFITTING
WARNING
Before refitting the seatback cover, check that the
velcro strips are properly fastened to the seat
cushion foam.
77A-7
178A REAR SEAT TRIM
Seatback trim 2/3 - 1/3 78A A
Remove the bolt (B).
Tightening torques
Release the trim from the seat belt strap.
Seatback frame - mounting bracket bolt 35 Nm
REMOVAL
Release:
– the armrest from its mounting,
– the retaining bracket from the seatback.
78A-1 Edition 2
REAR SEAT TRIM
Seatback trim 2/3 - 1/3 78A A
Partially remove the lining to access the headrest Unclip the cardboard trim.
guides.
WARNING:
When separating the lining from the foam, keep the
velcro strips in position (to avoid damaging the
foam).
Use tool Car. 1558 (colour blue) for the cover zip
fastener.
78A-2 Edition 2
REAR SEAT TRIM
Seat cushion trim 2/3 - 1/3 78A B
REMOVAL
REFITTING
Remove the cover retaining sections.
Proceed in the reverse order to removal.
WARNING:
When separating the lining from the foam, keep the
velcro strips in position (to avoid damaging the
foam).
78A-3 Edition 2
REAR SEAT TRIM
Seatback trim 1/1 78A C
Remove the bolt (B).
Tightening torques
Release the trim from the seat belt strap.
Seatback frame - mounting bracket bolt 35 Nm
REMOVAL
Remove clips.
78A-4 Edition 2
REAR SEAT TRIM
Seatback trim 1/1 78A C
WARNING:
When separating the lining from the foam, keep the
velcro strips in position (to avoid damaging the
foam).
REFITTING
Use tool (Car. 1558) (colour blue) for the cover zip
fastener.
78A-5 Edition 2
REAR SEAT TRIM
Seat cushion trim 1/1 78A D
REMOVAL
REFITTING
Remove the cover retaining sections.
Proceed in the reverse order to removal.
WARNING:
When separating the lining from the foam, keep the
velcro strips in position (to avoid damaging the
foam).
78A-6 Edition 2