Professional Documents
Culture Documents
Excuse me Coast Guard Command Center…..IS ANYONE receiving these requests for specifications on the BOP flange at the top so Inventors Branko R. Babic in Oxford England and
Brad Wehde plus Ruth DeLaMater Bundy/Ralph Charles Whitley, Sr. can give you a full illustrated presentation since no one apparently will contact your local UTILITY OR WATER
COMPANY OFFICIALS who will tell you at 5000 feet or 5 feet the same would seal instantly ?
I am on SKYPE ralphwhitleysr but also have a phone 813‐286‐2333 direct line and this disaster has now increased ten fold.
IS THERE A HUMAN READING THESE MESSAGES ?
Ralph
From: Ralph C. Whitley Sr. [mailto:backflow2@verizon.net]
Sent: Friday, June 04, 2010 2:50 PM
To: 'ATT_srm270'; 'Brad Wehde'; 'Branko R Babic'; Adrian; Governor Charley Crist; Charlie.Crist@myflorida.com; ri@dcf.pemex.com; President Barack Obama
Cc: CGRDCDeepwaterHorizon@uscg.mil; 'President Barack Obama'; bobby.jindal@la.gov; 'charlie crist'; info@deepwater.com; 'Innovative Technology'; 'Carol Browner, The White
House'; HorizonSupport@oegllc.com; 'Alternative Response Technology Alternative Response Technology'; Adrian; askdoj@usdoj.gov; CFO Alex Sink; Commissioner Rose Ferlita;
Commissioner Kevin White; horizonsupport@oegllc.com; bill@billnelson.senate.gov; john_mccain@mccain.senate.gov; americanvoices@mail.house.gov
Subject: RE: OIL DISASTER DEFCON 5 (srm reply1)
Importance: High
6/4/2010
Page 2 of 3
Brad
I did forward you material to an engineer (former) at Oak Ridge National Labs...to get your solution in front of them...hopefully through their contacts to
Deepwater BP command.
Just know that was done. I have put your proposal infront of the people I know who might assist to get to someone's attention...to contact you directly.
Same for Ralph's solution - will get that to review as well, if i have any opportunity to do it.
So....just know - I see your solution, and will do everything I can to get it to any responsible persons I know....ok? count on that.
I do not favor an "solution"...whatever works, fastest, highest chance of success, least risk of making it worse....I for THAT ONE...ok? :)
Keep me informed. About 98% of the people I've spoken with....just short circut....blank-out. They just don't get it...they react like Im asking, "Whats on
the menu/Pizza selections"...that kind of attitude/ no sense of 'urgency'...or that it particularily matters. Everyone thinks someone else is handling it...so
they ALL pass the buck...around in circles.
At 59...i can't believe that so many people...could be so unconcerned...like they are already 'dead' inside. and just fakking 'outside'.. Im only mentioning
here...in case you have been experiencing the same(?)...
best ...thanks for all you've done Brad...to follow it thru..and get is solved. If i do get through....your stuff goes right in front of them....and I have my own
approach, but cannont get the basic information to 'compute solution' (literally - "fastest time to solution"...to STOP it. (I have 3 methods / strategies of
approach)
Best -
steve
Steve
THIS IS RED ALERT
LOOK DEFCON 5. We are out of options here. Only FOR SURE option left.
Clean and well sort of simple.
Go to http://www.oceaneering.com/subsea‐products/pipeline‐repair‐systems/smart‐tap/
BUY THAT. Install it right below the BOP. Drill into the side that already has the BLOWOUT caused by the FAILED top kill (we know it is there even though you have not told us)
THEN BUY THIS http://www.oceaneering.com/subsea‐products/pipeline‐repair‐systems/piggable‐wye‐fitting/
attach this so you can plug up the BOP with wadded up Kevlar fabric. The stuff Tony may be wearing right now.
on the straight end place a 90 degree elbow with a flange run that to your riser up to the drill ship.
on the y part this is where you are going to send in your plug for the BOP, Unless you have something FOR SURE this time BP that is better, use a bunch of wadded up Kevlar fabric.
Do you know how to set this Piggable fitting up?
WE REALLY DON"T HAVE ANY OTHER OPTIONS. anyone can check this out with an engineer and it is doable with existing products. 100% seal, diverts flow to the drill ship so it does not
cause undue stress to the well bore.
If you need more information feel free to contact me.
if BP does not do this there is no hope, we will have a black tide of death and the destruction of the Gulf of Mexico and who knows what else. THIS IS THE LAST CHANCE.
You all saw the oil flowing out of the well now.
Does that look like 20% more to ANYONE?
BP has not done anything right yet. It is time to grab the B by the P and get something done.
If anyone can take this and get it to someone other than BP we may have a shot before they destroy anything that is left to fix.
If they remove the sippy hat there is a flange there with a few bolts on it, Lefty loosey righty tightie. Remove the flange and go to Cameron, oilstates or oceaneering (Hardware stores
for the oil industry)(real cool stuff) and pick up a few parts. It is all there. Everything they need. At this point they need no tricky caps domes or anything. There are even little devices
that can fix that little blowout from a bad weld underneath the BOP. They can get fancy and pick up a collet connector and put that on the flange and get a remote activated clamp
with riser to a drill ship. There are so many options, Cameron even has another BOP like the one that is on the floor here all busted up. They have a few real LMRP’s available also.
6/4/2010
Page 3 of 3
Everyone forward this to the President, Senators, and Congressman and any one you can think of .
Brad Wehde
Brad Wehde Interactive Media
65320 W Hwy 20
Bend, OR 97701
541‐389‐1261
email: brad@wehdeinteractive.com
website: http://www.wehdeinteractive.com
6/4/2010