Professional Documents
Culture Documents
www.NOV.com/GrantPrideco
Pipe Body OD
Pipe Body Wall Thickness
Pipe Body Grade
Drill Pipe Length
Connection
Tool Joint OD
Tool Joint ID
Pin Tong
Box Tong
(in)
(in)
(in)
(in)
(in)
(in)
80 % Inspection Class
Nominal Weight Designation
41.05
(ft) 31.8
Drill Pipe Approximate Length
(in) 3/32 Raised
SmoothEdge Height
(psi) 120,000
Tool Joint SMYS
Upset Type
IEU
(in) 6.000
Max Upset OD (DTE)
Friction Factor
1.0
5.875
0.750
G-105
Range2
XT57
7.250
3.500
10
15
Drill-Pipe Length
Best Estimates
(without Coating)
80 % Inspection Class
Applied Make-up
Torque
Max Tension
Operational
Torque (ft-lbs)
(lbs)
(ft-lbs)
Maximum MUT
81,500
Minimum MUT
67,900
Tension Only
Combined Loading
Tension Only
Combined Loading
0
70,700
984,700
736,800
0
55,600
984,700
840,000
Fluid Displacement
Fluid Displacement
Fluid Capacity
Fluid Capacity
Drift Size
48.53
0.74
(Bbls/ft) 0.0177
(gal/ft) 0.73
(Bbls/ft) 0.0174
(in) 3.375
XT57
7.250
Applied Make-up
Tension at Shoulder
Torque
Separation
(ft-lbs)
81,500
67,900
(ft-lbs)
(lbs)
(lbs)
Tensile Limited
1,700,100
SmoothEdge Height
(in)
(lbs)
3/32 Raised
7.438
1,539,200
46.83
0.72
0.017
0.76
0.018
(lbs/ft)
0.72
0.0172
OD X
(in)
3.500
Tension at Connection
Yield
(lbs)
1,463,500
1,748,300
ID
(in)
120,000
(psi)
(in)
(in)
7.337
6.566
6.566
135,800
1,748,300
(least accurate)
(gal/ft)
Nominal
(with Coating)
Connection Performance
Maximum Make-up Torque
Minimum Make-up Torque
Range2
(in)
7.250
1,301,100
6.566
483,900
Nominal
Assumed Slip Length
Transverse Load Factor (K)
(lbs)
(in)
834,800
(ft-lbs)
(ft-lbs)
(psi)
(psi)
(in)
(in)
(in)
(in^2)
(in^2)
(in^2)
(in^3)
(in^3)
5.875 (in) OD
80 % Inspection Class
661,900
(lbs)
G-105 )
Note: Slip Crushing: Slip crushing load is calculated with the Spiri-Reinhold equation from Why Does Drill Pipe
Fail in the Slip Area World Oil, 1959 for the slip length and transverse load factor shown and is for reference
only. Slip crushing is dependent on the slip design and condition, coefficient of friction, loading conditions, time in
slips, drill pipe OD and wall variation, and other factors. Consult with the slip manufacturer for additional
information.
16.5
4.2
Nominal
Pipe Tensile Strength
Pipe Torsional Strength
TJ/PipeBody Torsional Ratio
80% Pipe Torsional Strength
Burst
Collapse
Pipe OD
Wall Thickness
Nominal Pipe ID
Cross Sectional Area of Pipe Body
Cross Sectional Area of OD
Cross Sectional Area of ID
Section Modulus
Polar Section Modulus
(in)
Note: Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100psi.
Note: A raised elevator OD increases elevator capacity without affecting make-up torque.
6.125
6.721
662,000
7.438
1,267,900
139,200
0.98
111,400
23,457
23,386
5.875
0.750
4.375
12.075
27.109
15.033
13.786
27.571
5.875 (in) OD
80 % Inspection Class
984,700
106,600
1.27
85,300
21,447
20,169
5.575
0.600
4.375
9.378
24.411
15.033
10.560
21.119
G-105 )
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully
responsible for the accuracy and suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied
warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear
conditions (remaining body wall) is for information only and does not represent or imply acceptable operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance
ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to
the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.NOV.com/GrantPrideco/CustomerFeedback
XT57
80 % Inspection Class
Tool Joint OD
(in)
7.250
Tool Joint ID
Pipe Body OD
(in)
5.875
(in)
(ft-lbs)
0
3,700
7,400
11,200
14,900
18,600
22,300
26,100
29,800
33,500
37,200
41,000
44,700
48,400
52,100
55,800
59,600
63,300
67,000
70,700
(lbs)
984,700
984,100
982,300
979,200
975,000
969,600
962,900
954,700
945,400
934,800
922,800
908,900
894,000
877,400
859,100
839,100
816,500
792,400
766,000
736,800
G-105
(ft-lbs)
Connection Max
Pipe Body
Max Tension Tension
(lbs)
3.500
Operationa Assembly
l Torque
Max Tension
(ft-lbs)
(lbs)
Pipe Body
Max Tension
(lbs)
(lbs)
(ft-lbs)
Connection
Max Tension
(lbs)
984,700
984,700
1,700,100
984,700
1,463,500
984,100
1,463,500
2,900
984,300
984,300
1,700,100
1,463,500
5,900
983,100
983,100
1,700,100
1,700,100
982,300
979,200
1,463,500
8,800
981,300
981,300
975,000
1,463,500
11,700
978,700
978,700
1,700,100
969,600
1,463,500
14,600
975,400
975,400
1,700,100
962,900
1,463,500
17,600
971,100
971,100
1,700,100
1,463,500
20,500
966,300
966,300
1,700,100
1,463,500
23,400
960,600
960,600
1,700,100
1,463,500
26,300
954,200
954,200
1,700,100
1,700,100
954,700
945,400
934,800
922,800
1,463,500
29,300
946,700
946,700
908,900
1,463,500
32,200
938,700
938,700
1,700,100
894,000
1,463,500
35,100
929,800
929,800
1,700,100
877,400
1,463,500
38,100
919,600
919,600
1,700,100
1,463,500
41,000
908,900
908,900
1,700,100
1,463,500
43,900
897,300
897,300
1,700,100
884,700
884,700
1,700,100
1,700,100
859,100
839,100
816,500
46,800
1,463,500
792,400
1,463,500
49,800
870,700
870,700
766,000
1,463,500
52,700
856,000
856,000
1,700,100
736,800
1,463,500
55,600
840,000
840,000
1,700,100
Connection
Make-up Torque Range
Make-up Torque
(ft-lbs)
Min MUT
Max MUT
67,900
69,400
70,900
72,400
73,900
75,500
77,000
78,500
80,000
81,500
Connection Max
Tension
(lbs)
1,700,100
1,737,600
1,722,100
1,685,500
1,648,900
1,609,900
1,573,300
1,536,700
1,500,100
1,463,500
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
02-03-2014
XT57
Tool Joint OD
Connection
Wear
Tool
Joint OD
New OD
(in)
7.25
7.188
7.126
7.063
7.001
6.939
6.877
6.815
6.753
6.69
6.628
6.566
Worn OD
(in)
7.250
Tool Joint ID
(in)
3.500
Connection Max
Tension
Connection
Torsional
Strength (ft-lbs)
Max
MUT
135,800
131,700
127,600
123,500
119,500
115,500
111,600
107,800
104,000
100,200
96,500
92,800
81,500
79,000
76,500
74,100
71,700
69,300
67,000
64,700
62,400
60,100
57,900
55,700
(ft-lbs)
Connection Max
Tension
Min MUT
(lbs)
(lbs)
(ft-lbs)
1,463,500
1,514,900
1,565,600
1,577,500
1,545,500
1,509,300
1,463,500
1,346,200
1,233,700
1,124,900
1,023,600
926,800
67,900
1,700,100
65,800
1,657,700
63,800
1,617,500
61,700
1,539,800
59,700
1,427,900
57,800
1,322,500
55,800
1,218,900
53,900
1,121,500
52,000
1,028,100
50,100
937,700
48,200
852,100
46,400
772,000
Pipe Body
Combined Loading Table (Torque-Tension)
Pipe Body
Pipe Body OD
80 % Inspection Class
(in)
5.875
G-105
9,700
19,400
29,100
38,800
48,500
58,200
67,900
77,500
87,200
96,900
106,600
980,600
968,200
947,300
917,100
876,900
825,000
759,200
676,300
566,700
410,900
21,700
(ft-lbs)
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
02-03-2014