Professional Documents
Culture Documents
49.0 in
6.5 in
26.0 in
Construction of the Cabinet Top
Millwork:
1 Cut, plane and joint four boards to the following dimensions.
A One (1) at 49 x 6 1/2 x 3/4.
Assembly:
1 Lay boards side by side, and rotate them to alternate their growth rings.
2 Align the left edge of all four boards and draw a registration mark at 2 inches from this edge.
9.0
9.0
9.0
9.0
9.0
2
Registration Mark
3 Repeat 5 additional registration marks every 9 inches. These marks indicate where the biscuit slots will
be cut.
4 Using the biscuit cutter, install number twenty biscuits slots at each registration point.
5 Install biscuits and glue and clamp work piece together.
Crown Molding and Cabinet Top Stiles
25.177 in 25.177 in
23.0 in 23.0 in
47.354 in
43.0 in
41.0 in
1.5 in
2.375 in
0.64435 in
25
0.75 in
65
0.25 in
2.42427 in
Construction of the Crown Molding
Millwork:
1 Cut, plane and joint three sections of white oak to the following dimensions.
A Two (2) at 25 1/2 x 2 3/8 x 3/4
B One (1) at 48 x 2 3/8 x 3/4
2 Set the tablesaw bevel to 25 degrees.
3 Position the fence 2 7/16 to the left of the blade.
4 Placing the 2 3/8 side of each board against the table, rip the 3/4 side to 25 degrees.
5 Position the fence 1/8 to the right of the blade.
6 Placing the uncut 3/4 side of each board against the table, bevel the 2 3/8 side. Use featherboards as
necessary to keep the board tight against the fence.
7 Return the blade to 0 degrees bevel.
8 Attach a sacrificial strip to the tablesaw fence and position the fence against the blade.
9 Cut the remaining edges of the workpiece.
10 Do not cut the 45 degree angles on these pieces until the carcase has been completed and measured.
Assembly:
No independent assembly is required of these components.
Millwork:
1 Cut, plane and joint two sections of white oak to the following dimensions.
A Two (2) at 41 x 1 1/2 x 3/4
Assembly:
No independent assembly is required of these components.
Components of the Cabinet Base
23.75 in 23.75 in
6.5 in
6.5 in
44.5 in
6.5 in
0.25 in 45
6.5 in
0.75 in
Construction of the Base Molding
Millwork:
1 Cut, plane and joint three sections of white oak to the following dimensions.
A Two (2) at 24 1/2 x 6 1/2 x 3/4
B One (1) at 45 1/2 x 6 1/2 x 3/4
2 Set the tablesaw bevel to 45 degrees.
3 Position the fence 6 to the right of the blade.
4 Placing the 6.5 side of the board against the table, chamfer one edge of each board.
5 Do not cut the 45 degree joint angles on these pieces until the carcase has been completed and mea-
sured.
Assembly:
No independent assembly is required of these components.
Components of Right Cabinet Side
8.0 in
0.5 in
0.5 in
0.375 in
3.0 in 3.0 in 7.0 in 3.0 in
1.125 in
14.25 in
14.5 in
6.25 in
6.5 in
Components of Left Cabinet Side
8.0 in
0.5 in
0.5 in
0.375 in
14.25 in
14.5 in
6.25 in
6.5 in
Components of the Cabinet Shelves
41.75 in
20.25 in
0.5 in
0.375 in
41.0 in
0.5 in
3.0 in
Cabinet Door Assembly
16.0 in
1 in 14.0 in 1 in 3.0 in
2.0 in
2.5 in
3.0 in
6.75 in 3.0 in
25.75 in
24.75 in
25.0 in
33.0 in
1 in 5.25 in 2.0 in
5.0 in
4.5 in
1 in 14.0 in 1 in
16.0 in
Door Spacer Assembly
1.0 in 2.25 in
33.0 in
33.0 in
Drawer Bottom
39.5 in
21.75 in
Drawer Sides and Front
22.0 in
21.5 in
5.75 in
6.0 in
0.25 in
0.375 in
0.5 in
0.5 in
41.0 in
7.0 in
6.0 in
0.25 in
0.625 in
0.625 in
0.25 in
39.5 in
5.375 in