Professional Documents
Culture Documents
CHAPTER I
HISTORY OF FIREARMS IDENTIFICATION
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 2
CHAPTER II
FORENSIC BALLISTICS
INTRODUCTION:
In most advanced countries today, FIREARMS IDENTIFICATION plays an important role
in the administration of justice. This science has advantage over extracted confessions, direct
witnesses, and other circumstantial evidence. It is regarded as the highest form of uncontestable
and conclusive piece of evidence with the utmost legal significance.
ORIGIN:
The term Ballistics was derived from the Greek word ballo or ballein which means to
throw. Its roots was also said to have been derived from the name of an early Roman war machine
called the ballista - a gigantic bow or catapult, which was then used to hurl missiles or large
objects such stones at a particular distance to deter animals (games) or their enemy forces.
Ballistics dates back on the days of the famous French artist Leonardo da Vinci (1500 A.D.)
as can be gleaned in his sketch of Steam-Powered cannon to his primitive wheel-lock firearms.
BALLISTICS - In general or in its broadest sense, it is defined as the science of motion of projectiles.
- Technically, it refers to the science of firearms identification.
KINDS OF MOTION:
1. Direct the action of the expansive force of gases out of the burning powder.
2. Rotary the action of the rifling found on the inner surface of the barrel.
3. Translational the projectile hits the target and subsequently ricocheted.
ITS LEGAL MEANING It is the microscopic examination of fired cartridge cases and bullets
together with the recording and presentation by means of photography of what is revealed by the
microscope.
BRANCHES OF BALLISTICS:
1. Interior Ballistics
2. Exterior Ballistics
3. Terminal Ballistics
4. Forensic Ballistics - integral part of ballistics. Integral means necessary to the completeness of
whole.
5. Shot Ballistics
6. Wound Ballistics
I. INTERIOR BALLISTICS It is that branch of science that has something to do with the
properties or motions of projectiles while still inside the firearm. (From the time the Firer squeezes
the trigger). This extends from, the breech to the muzzle of the gun. Interior ballistics is so short.
From the release of the firing pin to the moment the sound of the shot can be heard as it leaves the
muzzle occupies only about 0.01 sec. in a modern rifle. A blow from the firing pin of a small-arms
weapon on the center of the primer cap compresses the primer composition violently between the
cap and the anvil, thus, causing the composition to explode, releasing the very hot gases and hot
particles. The holes or vents in the anvil allow the flame to pass through the primer vent in the
cartridge case thereby igniting the propellant. The powder begins to burn and the pressure inside
the cartridge rises rapidly almost at once, the bullet is pushed from the case mouth. At first, the
bullet is forced outward to make firm contact with the barrel so that the gas would be confined
within the chamber of the firearm. As the bullet moves down the barrel, the available combustion
space is increased. The powder burns progressively at first, increasing its burning rate faster that
the space increases. As long as this condition continues, the pressure continues to rise. The
maximum pressure is soon reached, when the two rates are momentarily equal. Thereafter, the
pressure drops till the bullet leaves the muzzle.
When the bullet charge is ignited, the pressure in the chamber begins to rise rapidly and soon
reaches a value high enough to move the projectile. The principal resistance to the motion of the
projectile at this stage is the force required to deform the rotating band to fit the rifling of the barrel.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 3
As the projectile moves, the propellant gas expands into the space behind it, the rate of the pressure
is reduced and the temperature of the gas begins to decrease. With increasing projectile velocity,
the expansion becomes rapid enough to cause the pressure to begin to drop. When the burning of
the charge is complete, and the evolution of the gas ceases, which usually occurs when the
projectile is from one third (1/3) on the way out of the barrel, the pressure drop becomes more
rapid. When the projectile leaves the bore with its full velocity, a few hundredths of a second after
ignition, the remaining pressure directs the propellant gas to the atmosphere.
Since the gun, as compared with a rocket, almost burns its propellant in a very short time and
large surface area is therefore required, a gun charge characteristically consists of a large number
of identical solid grains. Each of the grains is considered as burning simultaneously with the others
and in accordance with the laws of burning described above.
In addition to the laws of burning, a complete system of interior ballistic equations for the gun
includes three (3) other major members. The equation of state of the propellant gas relates to
PRESSURE, VOLUME, and TEMPERATURE OF GAS. The law on conservation of energy is
formulated to express the balance between the thermal energy of the gas and the kinetic energy of
the projectile and gas. Newtons second law of motion gives the acceleration of the projectile in
terms of the pressure of its base.
A subject associated with the interior ballistics is that on BORE EROSION and FOULING of
various kinds. Erosion is caused by the combination of temperature and velocity, while Fouling,
refers to the accumulated deposit within the bore of a firearm caused by the solid by-products
remaining after a cartridge was discharged.
II. EXTERIOR BALLISTICS it refers to that motion of projectiles from the time it leaves the
muzzle of the firearm to the time it reaches the target. The flight of most bullets does not exceed 30
seconds at maximum range, which for almost any firearm is obtained at an elevation of about 33.
This flight can be divided into three (3) distinct parts. During the FIRST, which last for only a few
yards, the bullet is recovering from the initial shock of firing, it is wobbly. The SECOND or
NORMAL period of flight extends for several hundred yards. During this time, it travels as it
should be, point first, with its axis rotation nearly on the trajectory. The FINAL period of flight
after the bullet has started to lose both velocity and spin. It again begins to wobble and finally over
or tumbles in an unpredictable manner.
Rifled bullets require spin to make them stable in flight. The proper amount of spin depends
on the size and weight of the bullet and its velocity. The spin imparted by the rifling, besides
making the bullet fly point-forward also shift, which in the case of a rifle having a right-hand
twist or spin makes the bullet go slightly to the right of the line of sight. The bullets center of
gravity travels along the parabola course of trajectory. But the point is kept about on the line of
sight by the gyroscopic action of the spin. It is the resulting couple, which moves the bullet to the
right. At extreme ranges, when the bullet is falling quite rapidly the point is still being held up by
this gyro-stillness effect, so that the bullet is finally traveling somewhat sideways through the air.
This is called YAW- the unstable rotating motion of the projectile.
Most modern rifles have sights, which can be adjusted to correct for windage, the term
used for the correction required for wind effect. With fixed sights for shooter has to estimate the
displacement that will be caused by the wind and aim that distance into the wind from his target.
This is often called Kentucky Windage from the habit of frontiersmen using Kentucky rifles
held-off in this manner for wind correction.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 4
1. MUZZLE BLAST - The noise created at the muzzle point of the gun by the reason of the sudden
escape of the expanding gas when it comes to instant contact with the air in the surrounding
atmosphere at muzzle point.
3. TRAJECTORY - The actual curve path of the bullet during its flight from the gun muzzle to the
target.
STAGES OF TRAJECTORY:
A. Straight horizontal line
B. Parabola like flight spinning flight of the bullet
C. Vertical drop
4. RANGE - the straight distance between the muzzle and to the target.
A. Accurate (effective range) - the distance within which the firer has control of his shots.
B. Maximum Range - the farthest distance that a projectile can be propelled from a firearm.
While the range at which the ordinary pistol and revolver are suppose to be effective only
at 50 to 75 yards, all of them will send their bullets much further than that and are capable of
inflicting fatal wounds at distances up to one mile, depending on the caliber and gunpowder
content.
NOTE: Rifled weapons maybe either be long-barreled rifles (2-3 ft.), or short barreled pistols
(1-12).
Bullets from rifled weapons would spin at 2000 to 3000 revolutions a second, but over the first
few yards of trajectory distance varies with the weapon their flight is slightly unstable; the end
of the projectile wobbles before it picks up a smooth flight path. This phenomenon is known as
TAILWAG, and is of considerable important in evaluating gunshot wounds. A bullet with
tailwag does not strike its target cleanly.
7. PULL OF GRAVITY - The downward reaction of the bullet towards the earth center due to its
weight.
8. PENETRATION - Depth of entry to which the bullet has entered its target.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 5
the firearm. Small firearms has an average muzzle velocity of 1,200 feet per second while high
powered firearms have 2,500 feet per second or more.
02. SPINNING MOVEMENT The bullet leaves the muzzle of the gun with spinning
motion on account of the lands and grooves inside the barrel, which are spirally arranged.
03. WABBLING MOVEMENT Aside from the spin of the bullet, these is a TAILWAG-
the bullet travels sideways and vertically. This movement maybe present not in the whole course
of the flight but only for some distance.
04. TRANSLATIONAL when the bullet hits the target and subsequently ricocheted.
05. PULL OF GRAVITY The pull of gravity may cause arch like trajectory of the bullet,
particularly after the bullet has lost certain degree of momentum in its flight.
DIVISIONS:
01. Field investigations Refers to the work of an investigator in the field. It concerns mostly
with the collection, marking, preservation, packing and transmission of ballistics exhibits such as
fired bullets, fired shells, firearms, and allied matters.
V. SHOT BALLISTICS
- Refers to the study of shots from smooth bore firearms like shotgun and muskets.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 6
A shotgun is a shoulder-fired firearm having a barrel that is smooth-bored and is intended
for the firing of a charged compound of one or more round balls or pellets.
The muzzle velocity of shotgun is about half that of a center fire rifle, and shot loses speed
more rapidly than a conical bullet, shot with high velocity powder charge has a muzzle velocity of
around 1,300 feet per second. With No.6 shot, this represents an average velocity at 40 yards of
only 975 per second. Shot in flight has string or pattern. The load strings out while moving
through the barrel, and at 40 yards, the average string is 12 feet at a 30 inch circle at 40 yards.
Unlike the rifle, the shotgun requires that aim be ahead of the target. The target is usually
rising as well as moving away, so both vertical and horizontal leads must be used. The first
shotguns had cylinder bores, uniform in diameter throughout their length. Bun makers found out
that a sight restriction or choked at the muzzle improved the pattern. Commonly, a short section
of reduced diameter joins the main part by the conical taper. A swaged choke has simple conical
section at the muzzle. The recessed choke has a slightly enlarged portion of barrel, with conical
sections fore and aft. Full chokes are used for a long-range shooting. Modified chokes or cylinder
bores are for upland birds and skeet shooting.
Shot pellets being spherical projectiles, their sectional density increases with diameter.
Thus, large shot will retain velocity better than a smaller size, besides having greater striking
energy. No. 2 shot has at least 50 ft/sec more velocity at 50 yards than no.6. Higher average velocity
requires less lead minimizing pointing errors. All things being equal, large shot gives more kills
at longer ranges than small shot, but the statement is true only per shot pellet. No.6, with many
more pellets per load than no.2, gives a better pattern, hence, more hits. Thus, the load must be
compressed.
Before chokebores were generally available, many ideas were advanced for concentrating
the shot in flight. They involve little wire or mash baskets, and metallic containers or paper tubes
which separate in flight. Modern manufacturers have done much research to provide better
patterns and reduced shot string.
CLASSIFICATION OF A SHOTGUN:
A. As to the number of shots:
1. Birdshot The shot are small ranging in sizes from 0.05 inch to 0.15 diameters and loaded from
200 to 400 shots in the shell. Birdshots are small and are commonly used for hunting fowls and
other small animals.
2. Buckshot The shot ranges from 0.24 to 0.33 inch in diameter and obviously fewer in number
in a shot. A standard 12-gauge shotgun contains only nine shots.
3. Single Projectile (Rifled Slag) There is only a single shot or slug in a shell.
B. As to the systems employed in the determination of the diameter of the barrel of a shotgun:
1. Gauge System Determination of the number of lead balls, each fitting of the bore totals to
one pound in weight. The smaller the gauge designation, the larger is the bore. If twelve balls
can be made from one pound of lead, each fitting the inside of the barrel of a shotgun, the
gun is called 12-gauge or 12-bore shotgun. 12-gauge shotgun is the most commonly used.
2. Expression of the Bore Diameter in Inches The 0.410 bore shotgun is the only shotgun at
present to be so designated.
3. Metric system The bore is expressed in millimeters.
C. As to the length of the barrel:
There is no standard length of the barrel but modern barrels measure 26, 28, and 30 inches in
length.
D. As to the Grade of Choke:
A shotgun is choked when the muzzle end of the barrel is a diameter smaller than the rest of the
barrel. The main purpose of the constriction is to minimize the dispersal of the pellet or buckshot
after the shot. It is based on the presence or absence of choke and the degree of choking, that
shotguns are classified as:
1. Unchoke The diameter of the barrel from the rear end up to the muzzle is the same.
2. Choke The diameter of the barrel at the muzzle end is smaller than the rest of the barrel.
a. Improved Cylinder The narrowing of the barrel by 3 to 5 thousands of an inch.
b. Half Choke narrowing by 15 to 20 thousands of an inch.
c. Full Choke narrowing from 85 to 40 thousands of an inch.
The lethal range is normally in an area of 30 inches in diameter at 30 to 40 yards according
to the degree of choking.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 7
(2) Over-and-under barrel.
Shotgun Cartridge:
A shotgun cartridge is usually 2-3/4 or 3 inches long and the diameter depends on the gauge of
the firearm. The base and the lower portion of the cylindrical portion are made of brass with the
primer cap at the center of the base. Attached to the free end of its cylindrical portion is the
cylindrical laminated paper tube to complete the shell easing.
When the trigger is pulled, the firing pin activates the primer, which in turn ignites the powder
charge. Explosion of the gunpowder will cause propulsion of the wad and pellets (shot) in front.
The muzzle velocity of the pellet is relatively smaller as compared from those discharged from
rifled firearms.
Except for the presence and nature of the slug, the component of the shotgun blast is almost the
same as that of a rifled firearm. It also consists of gunpowder, flame, smoke, pellets and wad.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 8
protruding. protruding from the wound.
7. Always present after fire. 7. May be absent, if missile is lodged in
the body.
8. Paraffin test may be positive. 8. Paraffin test always negative.
The Odd and Even Rule in Gunshot Wounds:
If the number of gunshot wounds of entrance and exit found in the body of the victim is
even, the presumption is that no bullet is lodged in the body, but if the number of the gunshot
wounds of entrance and exit is odd, the presumption is that one or more bullets might have been
lodged in the body.
The rule is merely presumptive and actual inspection and autopsy will verify the truth of
the presumption. It may be possible that all of those wounds or a majority of them are entrance
wounds with some bullets lodged, yet the number may still be even.
Sometimes it is difficult to locate the lodged bullet but with the help of a portable X-ray, its
location and extraction can be facilitated.
How to Determine the Number of Fires Made by the Offender:
1. Determination of the Number of Spent Shells:
Search must be made at the scene of the crime or at the place where the offender made the fire,
for spent shells, if the weapon used is an automatic pistol or rifle. In case of revolver fire, the
empty shells may be found still inside the cylindrical magazine. In machine gun fire, the spent
shells may still be attached to the cartridge belt.
3. Tandem Bullet:
Two or more bullets leaving the barrel one after another. In cases of misfire or a defect in the
cartridge, the bullet may be lodged in the barrel and a succeeding shot may cause the initial and
the succeeding bullet to travel in tandem. There is a strong possibility for them to enter the target
in a common hole. This might create doubt to the statement made by the firer that he made only
a single shot, but ballistic examination can show as to whether the bullet traveled in tandem.
Entry wound are generally clean, round holes slightly smaller than the bullets which caused
them; as the bullet travels through the body it produces a shock wave which damages the tissue
around its path. This is known as TISSUE QUAKE. The bullet will slow down by the passage
through the body and its exit will leave an irregular hole. If the bullet exits head-on, the wound
will be smaller than the entry, but if it leaves the body at an irregular angle, or takes pieces of bone
with it, the exit wound will be ragged.
Contact wounding with the muzzle pressed against the skin will produce not a round entry but
star shaped hole with lacerated edges.
SHOTGUN DISCHARGED
At a close range, from 1 to 3 ft, a more or less irregular wound about 1 to 2 inches in
diameter will be produced. There will be evidence of scorching and tattooing, singeing of hair by
flame unless the weapon was fired through the clothing. Beyond the range of 3 ft the shot begins
to spread out and at 4 ft the wound will appear as central hole with small perforations around it.
At ranges over 4 ft the shot continues to spread out and produces a mass of small perforations with
no central wound. An approximation of the range can be obtained by measuring in inches the
diameter of the wound (including the outermost perforations) subtracting 1, thus arriving at the
range in yards. Thus a wound of 9 inches diameter indicates that it was inflicted by a weapon fired
from about 8 yards; the exact range depends on the choke of the weapon and only test firing gives
the accurate answer.
Sir Sydney Smith founder of the Medico-Legal Faculty at Cairo University and later Regis
Professor of Forensic Medicine at Edinburgh, was one of the leading exponents, studying entrance
and exit wounds, powder burns, and powder tattooing on human skin and other medical
phenomena associated with gun fire.
CHAPTER III
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 10
FIREARMS
ORIGINS OF FIREARMS:
The first definite reference to a firearm is an English manuscript of 1326, De Officials
Regnum ( On the Duties of Kings), in which there is an illustration of a small cannon being fired,
but it was not until the closing of the century that technology had evolved sufficiently to allow the
first handgonne to appear. The contents of the manuscript De Officials Regnum is hazy but it
could be safely said that it is somewhat parallel to Mao Tse Tungs idoneous remarks that power
emanates from the barrel of the gun. Then, the ridaudequin was developed, which appeared
in about 1380. It consisted of a number of small-caliber cannon barrels mounted on a light cart, the
barrels being splayed apart so as to deliver their shots in a fan-shaped arc to the front. While these
weapons appear to have been effective, they had one major limitation: they were fixed to their carts
such that they could not deal with an enemy who suddenly appeared on the flanks. The logical
step was to take on the same barrels and attached it to a wooden pose, with the powder and the
shot, and with the man holding a length of burning rope, he could tuck the pole under his arm
should a target appear, roughly aiming the weapon and touch it off by applying his burning
match to the vent of the gun to ignite the gun powder. In this manner, the portable handgun
arrived in the battlefield. The handgonne was therefore the transitional stage between the
cannon and the family of weapons which we collectively call small arms
The first handguns were simply reduced cannons, because of their smaller size. The earliest
known specimen is the Tannenberg gun, so called because of its discovery in a well at the ruins
of the castle of Tannenberg (not the Tannenberg in former Prussia, but a small castle in Hesse.)
Since this castle was destroyed in 1399, the weapon must date before that, and the existence of
handguns in the 14th century is borne out by the English Privy Wardrobe accounts for 1388 which
record III(3) cannons parvos vocatos handgunnes. The Tannenburg gun is cast in bronze, octagonal
in section. A bronze gun similar in date and hexagonal in shape was recovered from the sea of
Morko in Sweden.
Some guns were made in iron. One of the earliest known specimens was found at the
Vedelspang in Schleswig, Germany. They were known as hook gun because there was hook
beneath the barrel. Vedelspang was another castle, which, according to records was destroyed in
1426.
Early in 1411, some thought had been given to the mechanics of directing fire: a German
engraving of that year shows a handgun with a serpentine matchlock, an S-shaped piece of
metal pivoted at its center to the side of the stock. The gunner could use both hands to hold and
fire.
Rifles first appeared towards the end of the 14th century. Gun makers in Nuremberg are
given the credit for its invention. For a long time, its value was not appreciated because the lead
ball had to be driven down with a ramrod and mallet to load the rifle compounded by poor
gunpowder. Thereafter, it was further improved and was used in sporting events. Then, in about
1600, Christian IV of Denmark had wheel lock rifles made for some of his troops and some French
cavalry were issued with rifles by 1680.
The American War of Independence (1775-1783) led to the more general acceptance of the
rifle as a military weapon. In 1774, Lt. Col. Patrick Ferguson of the British Army designed his rifle
and demonstrated it before the King of Windsor resulting in orders for 100 rifles. Ferguson
supervised the manufacture of rifles, trained a company of men in the use of the rifle and sailed
for America in 1777. Ironically, an American rifleman killed him in 1780 and his company was
disbanded.
By the early part of the 15th century, the handgun began to change its form. The hook gun
was further refined by German mercenaries which they generally called Lansknecht stock, which
was more controllable than the crude Hook Gun because it consisted of a piece of wood placed
underneath the barrel and retained by iron straps and the rear end shaped roughly to fit against
the mans shoulder.
In 1517, the wheel lock was invented. In praise of this weapon, even Emperor Maximilian
I (1459-1519) of Austria made a great epic poem entitled Teurdanckh. However, he enacted
restrictive laws against carrying of self-ignited handguns an early example of legal restrictions of
firearms which continues up to this day. Eleven years before, however, the Statues of the Shooting
Range at Geislingen had already forbidden the use of the wheel lock. The interest of the Hapsburg
rulers in firearms led them to play an important part in the development of the wheel lock, and
many of the extant wheel lock firearms were made at Augsburg and Nurnburg. The earliest extant
wheel lock with which a date maybe associated is a combination of crossbow and wheel lock pistol
in the Bavarian National Museum, Munich, Germany. This weapon bears the heraldic arms of the
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 11
Archduke Ferdinand and the initials F and A; it may be reasonably dated 1521, which was the year
of the Archdukes marriage.
People had used flint to strike sparks for many thousand years, so it was not surprising that
this system should be applied to firearms. Thus, the flintlock gun was born. In 1547, the Spanish
lock or miquelet was developed by Simon Marquette, the son of an Italian gun maker who had
settled in Spain. It was a kind of handgun which George Washington used in the U.S. Civil War.
His flintlock pistol is displayed in the West Point Museum up to this day.
In Europe, the matchlock mechanism was retained for centuries. The Thirty Years War
(1618-1648) was fought with matchlock and many military writers continued to praise its
superiority over wheel locks.
In America, the majority of the early colonists at Jamestown, New Netherlands and
Plymouth used the matchlock because it was inexpensive and easy to make. Such guns, procured
from the Dutch traders at Albany, were in the hands of the Indians in the Connecticut valley as
early as 1648.
Match-lock guns became widely diffused in Asia and North Africa, where they remained
in use long after they become obsolete in Europe. The match-lock mechanism was introduced in
India probably in the early part of the 16th century. It was in the year 1510, when Goa, was occupied
by the Portuguese, thus, it may be taken as the date of the permanent introduction of the matchlock.
The Portuguese also introduced firearms into Japan when they landed on the island of
Tanegashima in 1542. The local armorers copied the matchlock muskets that the Europeans
brought with them. No wonder, when World War II was declared, they were all fully armed with
their own version of firearms. (See Encyclopedia of Rifles and Handguns, A comprehensive Guide to
Firearms. Edited by Sean Connoly, 1996 Ed., pp.1-29 and Vol. 9, Colliers Encyclopedia, 1989 Ed., pp. 729-
736)
In the early 18th century Samuel Colt (1814-1862) (a) revolutionalized the design of the
revolver and more importantly, he (b)introduced the system of mass production of such weapons.
He produced a revolver with a cylinder that was drilled with five or six chambers, each with its
own tube to hold a percussion cap. In fact, his name is synonymous with the revolver, although
his venture into the arms business was not a great success, but by luck and perseverance, he
remained in business. By the start of the American Civil War in 1861 (which lasted till 1865),
continued in the firearms business and they led in firearms manufacturing especially during the
outbreak of the First World War when they mass-produced the .45 caliber pistol. To this day, they
still lead in the manufacture of firearms.
Thereafter, handguns and rifles were refined and refined as the years passed by and all
modern firearms were developed and widely used in every major war starting from the First World
War to the Second World War and including the Gulf War of 1991.
02. MATCHLOCK
- The construction of the matchlock was exactly the same as the hand cannon. Common in
them is that it was muzzle loaded and had a touch-hole covered with a priming charge. The only
difference being that the match lock, a slow burning piece of cord used the priming charge, was
held in an armed hook screwed to the side of the flame. To fire the gun, the hook was pushed
forward to drop the burning end of the match into the priming charge. As these weapons be were
becoming sophisticated, the curved hook was embellished and took the form of a snake and
became known as the weapon Serpentine.
Eventually, the tail of the serpentine was lightened and became the forerunner of the modern
TRIGGER. These weapons were used during the time of Henry VIII who reigned from 1509 to 1547,
were many of his cavalry were armed with a matchlock.
The major defect with this type of firearm was that it required a slow burning match for
ignition. As a result, it was of little use for surprise attack or in damp or rainy conditions.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 12
03. WHEEL-LOCK
The lighted match used in the matchlock was no longer necessary. When fired from the
shoulder, the wheel-lock was often referred to as an arquebus from the shape of the butt which
was often curved to fit to the shoulder. This weapon consisted of a serrated steel wheel, mounted
on the side of the weapon on the rear of the barrel. The wheel was spring-loaded via a chain round
in its axles with a spanner similar to a watch drum. When the wheel was turned with a spanner,
the chain would turn the axle and the spring was tensioned. A simple bar inside the lock kept the
wheel from unwinding until released with the trigger. Part of the wheel protruded into a small
pan, the flash pan or priming pan, which contained the priming charge for the touch-hole. The
serpentine, instead of containing slow burning match, had a piece of iron pyrite fixed in its jaws.
This was kept in direct contact with the serrated wheel by means of a strong spring. In pressing
the trigger, the bar was withdrawn from the grooved wheel which then turned on its axle. Sparks
produced from the friction of the pyrite on the serrated wheel ignited the priming charge which in
turn ignited the main powder charge and fired the weapon. It was invented by JOHANN KEIFFUS
of NUREMBERG, GERMANY in 1517.
04. FLINT-LOCK
- The ignition system which superseded that of the wheel-lock was a simple mechanism
which provided a spark by striking a piece of flint against a steel plate. The flint was held in the
jaws of a small vice on a pivoted arm, called the COCK. This was where the term COCK THE
HAMMER originated.
LEONARDO DA VINCE (1500 AD) A French artist, on his sketch of a steam-powered cannon
to his primitive wheel-lock firearms.
13th Century - development of firearms followed the invention of gunpowder in Western Europe.
BERTHOLD SCHWARTZ - A German monk, and ROGER BACON. an English monk are both
credited with gunpowder invention.
Most reference books credit Roger Bacon, English monk and scientist, with the invention of gun
powder in 1248, and Berthold Schwartz, with the application of gun powder to tie propelling of a
missile in the air 1300s. This powder is what we now call black powder.
1118 - Moors used artillery against Zaragoza. Early manuscripts tell or several Moorish campaign
in which, artillery was used all dating prior to Bacon and Schwartz.
1245 - Gen. Batu, the Tartar leader used artillery in Liegnitz when he defeated the Poles,
Hungarians and Russians.
1247 - one of the earliest recorded uses of firearms in warfare was that of an attack on Seville, Spain.
1346 - Cannons used by King Edward III of England at Crecy.
1353 Mohammed II of Turkey in his famous conquest of Constantinople.
First firearms were inefficient, large and heavy and were not capable of being carried by an
individual soldier, hence, the development of cannons preceded that of small arm weapons by
almost 50 years.
Man never satisfied with himself, he is always trying to improve himself and his
surrounding. He created some crude or primitive weapons, which were subsequently developed
into sophisticated firearms of modern times. The following are the stages of development of mans
weapon:
1. STONES
2. CLUBS
3. KNIVES
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 13
4. SPEARS AND DARTS SLINGSHOTS TO HURL OBJECTS
5. BOWS AND ARROWS
6. CROSS-BOWS
7. GUNS
8. MISSILES
PERSONALITIES IN BALLISTICS
1. Col. Calvin H. Goddard, Md., OS, U.S. Army Father of Modern Ballistics
2. Horace Smith Founded the great firm Smith & Wesson and pioneered the making of
breech-loading rifles.
3. Daniel B. Wesson - an associate or partner of Smith in revolver making.
Designed the Model 1895 Box Magazine, lever action type of rifle for Winchester. He also
earned respect and recognition with pistols and machine guns.
Designed the first successful gas-operated machine gun. His water-cooled Browning
caliber .30 and Browning Automatic Rifle were extensively used in World War I.
4. John M. Browning - Wizard of modern firearms and pioneered the breech loading single
shot rifle.
5. John T. Thompson Pioneered the making of Thompson Submachine gun.
6. David Carbine Williams maker of the first known carbine.
Carbine, like most of the very old terms used in the history of firearms, its actual origin
cannot be positively established. It is believed that the term might have originated from the
following:
carabine- which means Spanish Cavalry
carabs- which means small ships
karab an Arabic term which means weapon
William Carbine first known maker of carbine firearm
7. Alexander John Forsyth Father of the percussion ignition.
8. Elisha King Root Designed machinery of making Colt firearms.
9. Eliphalet Remington one of the first rifle and ammunition makers.
10. John Mahlon Marlin - founder of Marlin Firearms Company.
11. James Wolfe Ripley Stimulated the development of the Model 1855 rifled-musket.
12. Samuel Colt (1814-1862) of Hartford, Connecticut, produced the first practical revolver
bringing it to what most gunsmiths would agree was its perfect form in the Colt Army 1873
model, which became famous for its .45 caliber. He also introduced the system of mass
production of such weapons.
Other manufacturers followed Colts lead: Remington and Smith & Wesson in the U.S.,
Adams and Scott-Webley in BRITAIN, Star, Luger, Browning and Beretta on the CONTINENT,
until revolvers were used in every part of the world.
13. Henry Derringer he gave his name to a whole class of firearms (rifles and pistols)
14. John C. Garand designed invented and introduced the semi-automatic US Rifle, Cal. .30
M1 which is gas operated after Thompson did nod improve satisfactorily because of oiling
requirements, jams, and feeding troubles. He was hired by the U.S. Government and given
employment at Springfield Arsenal to continue development of automatic firearms.
15. Oliver F. Winchester one of the earliest rifles and pistol makers.
16. Hiram Maxim (1840-1916) Born in Maine, he settled in Britain, where he invented his
machine gun.
He also developed a smokeless form of gunpowder called maximite. He was Knighted in
Britain in the year 1901 for his inventions.
17. Hugo Borchardt Employed with Winchester for a time. He developed one of the earliest
successful auto loading pistol. When he couldnt get American makers into making it, he took
his design to Germany and was developed into the worlds famous LUGER PISTOL.
18. James Gatling Created the first successful mechanical machine gun. Said machine gun was
used during the U.S. Civil War (1861-1865). The gun had several barrels, which revolved around
a central axis.
19. James Puckle He attempted to design a machine gun in the year 1717. In trial, the gun
fired up to nine shots every minute, but the British Army was not impressed and it was soon
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 14
forgotten.
DEFINITION OF FIREARM:
1. Technical Definition:
A firearm is an instrument used for the propulsion of a projectile by the expansive force of
gases coming from the burning of gunpowder.
2. Legal Definition:
Section 877, Revised Administrative Code - Firearm defined.
Firearm or arm, as herein used, includes rifles, muskets, shotguns, revolvers, pistols, and
all other deadly weapons from which a bullet, ball, shot, shell, or other missile may be
discharged by means of gunpowder or other explosives. The term also includes air rifles except
such as being of small caliber and limited range used as toys. The barrel of any firearm shall be
considered as a complete firearm for all purposes thereof.
Firearm refers to any handheld or portable weapon, whether a small arm or light weapon, that
expels or is designed to expel a bullet, shot, slug, missile or any projectile, which is discharged
by means of expansive force of gases from burning gunpowder or other form of combustion or
any similar instrument or implement. For purposes of this Act, the barrel, frame or receiver is
considered a firearm (Section 3, R.A, 10591-Approved on May 29, 2013).
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 15
pesos, in the discretion of the court. If the article illegally possessed is a rifle, carbine, grease gun,
bazooka, machine gun, submachine, hand grenade, bomb, artillery of any kind or ammunition
exclusively intended for such weapons, such period of imprisonment shall be not less than five
years nor more than ten years. A conviction under this section shall carry with it the forfeiture of
the prohibited article or articles by the Philippine Government.
Section 2690. Revised Administrative Code:
Selling of firearm to unlicensed purchaser:
It shall be unlawful for any dealer in firearms or ammunition to sell or deliver any firearms
or ammunition or any part of a firearm to a purchaser or other person until such purchaser or other
person shall have obtained the necessary license therefore, Any person violating the provisions of
this section upon conviction in a court of competent jurisdiction, shall be punished by a fine not
exceeding two thousand pesos, or by imprisonment not exceeding two years, or both.
Section 2691, Revised Administrative Code;
Failure of personal representative of deceased licensee to surrender firearm:
When a holder of any firearm license shall die or become subject to legal disability and any
of his relatives, or his legal representative, or any other person shall knowingly come into
possession of any firearm or ammunition covered by such license, such person, upon failure to
deliver the same to the Chief of Constabulary in Manila or to the senior officers of Constabulary
in the province, shall be punished by a fine not exceeding five hundred pesos or by imprison-
ment not exceeding six months, or both.
READ: R.A, 10591-Approved on May 29, 2013 An Act for Comprehensive Law on Firearms and
Ammunition and Providing Penalties for Violations Thereof
HAND/SHORT ARMS
Portable handguns appeared only in the early years of 16th century.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 16
smooth from the firing chamber to the muzzle.
Example: Shotgun
b. Rifled Bore Firearm This is a firearm with the bore of the barrel with a number of spiral
lands and grooves which run, parallel with one another, but twisted spirally from breech to
muzzle.
Example: Military Rifle
3. As to the Manner of Firing:
a. Pistol - Firearm, which may be fired only by a single hand.
Example: Revolver.
b. Rifle Firearm which may be fired from the shoulder.
Example: Shotgun
4. As to the Nature of the Magazine:
a. Cylindrical Revolving Magazine Firearm The cartridge is located in a cylindrical
magazine, which rotates at the rear portion of the barrel.
Example: Revolver.
b. Vertical or Horizontal Magazine The cartridge is held one after another vertically or
horizontally and also held in place by a spring side to side or end to end.
Example: Automatic Pistol.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 17
to 5 tons per square inch which blows back the side. The slide action, like that of the rifle bolt,
ejects the spent cartridge, extracts a new one from the magazine and slots it into firing position
once more.
For purposes of Medico-legal Investigation, the following Parts of a Firearm are important:
1. The trigger with the firing pin.
2. The barrel
(From: Modern Criminal Investigation by Harry Soderman and John OConnel, 4th ed., p. 201).
Second Sentence:
.22 minimum caliber
.19
.18 only used as toys, they could not be considered as a firearm
.17
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 20
2. Revolvers 4. shotguns
03. Bolt Action Type reloading is done by manipulation of the bolt.
Ex. 1. rifles 3. Machine guns
2. shotguns
04. Automatic Loading Type after the first shot is fired, automatic loading or feeding
of the chamber takes place.
Ex. 1. Rifles 2. Shotguns
05.Slide Action Type (thrombone) loading takes place by back and forth manipulation
of the under forearm of the gun
Ex. 1. rifles 2. shotguns
06. Lever Type (Break-type) loading takes place by lever action on the firearm.
Ex. 1. rifles 2. shotguns
DETAILED PARTS
REVOLVER .38 AUTOMATIC PISTOL .45
1. Barrel Assembly 1. Barrel Assembly
a. breech end a. breech end
b. muzzle end b. muzzle end
c. bore c. bore
d. riflings (lands and grooves) d. riflings (lands and grooves)
e. front sight e. chamber
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 21
f. make f. interlocking ribs
g. barrel lug
h. barrel ink
i. barrel ink pin
j. barrel lead (lead)
The automatic Pistol, Caliber .45 besides having the main parts and detailed parts it has also
the so called auxiliary parts accessories) which must all be removed first before disassembly of the
weapon can be accomplished.
1. Recoil plug 4. Recoil spring
2. Barrel bushing 5. Recoil spring guide
3. Slide stop pin
ADVANTAGES OF REVOLVER:
1. It is old standard weapon, everyone is used to it and almost everyone knows something
about how to handle it.
2. The revolver is safer for inexperienced people to handle and carry than an automatic pistol.
3. The mechanism of a revolver allows the trigger pull to be better than that of the average
automatic weapon.
4. A misfire dies not put a revolver out of action.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 22
5. It will handle satisfactory old or new or partly deteriorated ammunition, which gives
reduced velocity that would jam an average automatic pistol.
DISADVANTAGES OF A REVOLVER:
1. It is more bulky to carry than that of an automatic pistol.
2. Its grip or handle is generally not as good as that of pistol.
3. It is hard to clean after firing.
4. It is slower to load.
5. It is harder to replace worn out or broken parts, it is a factory job.
6. Worn out or poorly made weapon is subject to variable accuracy due to improper lining up
of cylinder.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 23
CENTER PIN serves as a locking device for the cylinder
CENTER PIN SPRING holds the center pin in a locked position
SIDE PLATE provide access to the internal parts
SIDE PLATE SCREWS hold the side plate and yoke in place
HAMMER BLOCK safety device that prevents hammer blow to primer
DOUBLE ACTION SEAR built to allow double action fire
HAMMER strikes the blow that initiates or ignites the primer
BOLT disengages pin and allow opening of cylinder and blocks hammer
THUMBLATCH actuates bolts to release the cylinder
HAND (Pawl) rotates the cylinder when the hammer is cocked
CYLINDER STOP stops and holds the cylinder when the hammer is cocked
TRIGGER actuates the parts necessary to fire the weapon
TRIGGER GUARD guards the trigger from unnecessary action to avoid accidental firing
REBOUND SLIDE returns trigger, actuates hammer block and locks hammer
TRIGGER SPRING provides energy for return movement of rebound slide
TRIGGER LEVEL contacts rebound slide to return trigger forward
MAIN SPRING provides energy to the hammer to activate firing mechanism
STRAIN SCREW controls tension on the mainspring
TRIGGER STOP prevents excessive rearward movement after hammer release
RATCHET helps in the withdrawal of the cartridge or shells from the chambers of the cylinder
CYLINDER NOTCH it helps hold cylinder in place and aligned ready for firing.
CHAPTER IV
AMMUNITIONS/CARTRIDGES
INTRODUCTION:
It is important for students of firearms investigation and identification to be well versed
with ammunitions. This chapter limits itself only to metallic and modern shotgun shells since these
are the types greatly encountered by investigators in most cases.
Originally, the word ammunition means any unfired assembly of cartridge case, powder,
primer, and projectile which maybe used in a firearm. But today, the word is generally used when
referring to a supply of assembled cartridges in bulk as in boxes or lots. It is also often used to
refer to the supply a person maybe carrying with him. The term round refers to a single cartridge.
Legal Definition:
Shall mean loaded shell for rifles, muskets. carbines, shotguns revolvers, and pistols form
which a ball, bullet, shot, shell, or other missiles may be fired by means of gunpowder or other
explosives.
Technical Definition:
A complete unfired unit consisting of bullet, cartridge case, propellant powder, primer.
ORIGIN:
16TH CENTURY - cartridge was discovered.
The earliest small arms cartridge consisted of a pre-measured charge of powder wrapped in
paper.
The term cartridge derived from the Latin word charta means paper and from the French
word cartouche meaning a roll of paper.
Introduction of magnum cartridges in the fifties (50s) first manufactured by Remington
and used to load such weapons as the Luger Blackhawk and the Smith & Wesson .44 magnum
has meant that handguns are harder hitting, but their mechanism is largely unchanged and their
victims suffer in much the same ways as the older weapon.
NOMENCLATURE/PARTS OF A CARTRIDGE:
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 24
I. Bullet Refers to the projectile propelled form a firearm by means of the explosive force of
gases coming from burning gunpowder.
2. Cartridge Case Refers to the tubular metallic container for the gunpowder. Sometimes called
shell.
3. Gunpowder Refers to the propellant which when ignited by the primer flash is converted to
gas under high pressure and propels the bullet or shot charge through the barrel and on to the
target.
4. Primer Refers to the metal cap containing the highly sensitive priming mixture of chemical
compound which when struck by firing pin would ignite. Such action is called Percussion.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 25
- The first cartridge of a self-loading type, which was commonly attributed to Monsieur Le
Facheux of Paris, at around 1836.
- The firing pin strikes a needle, which is placed at the rim of the shell. The needle will then
press on the Percussion cap which is inside the cartridge. This type is obsolete and now rarely
found.
d. Ring fire Cartridge
- A type of cartridge used only on sabotage cases. The chattel cartridges of Steyr advance
combat rifle and Steyr anti-material squad machine gun. This is a special type of cartridge
wherein the priming mixture is placed in a circular hollow ring about 1/3 of the base of the
cartridge.
SHOTGUN SHELL
--- Single unit of ammunition for shotguns.
--- It is usually larger. Used in smooth bores capable of withstanding far less pressure.
A. Paper tube G. Priming
B. Metal Base H. Propellant
C. Base wad I. Over-PowderWad
D. Battery Cup J. FillerWads
E. Primer cup K. Shot
F. Anvil L. Closing Wad
Shotgun bores are measured in gauges, with the smaller the number, the larger the diameter.
Thus, a I2-gauge shotgun has a larger diameter bore than a 20-gauge. The term gauge was
originally the number of lead balls of that size weighing 11 lb. This system does not hold for the
400 gauge which is in actuality a caliber.
- Some shotguns are named by caliber, as for example, the one that is called .410 gauge
shotgun. In this case .410 gauge actually means .41 caliber.
- 12-gauge shotgun has a caliber of .729 inch.
KINDS OF SHOTS
I. BUCK SHOT 9 to 12 pellets
2. SINGLE SHOT only one pellet
3. BIRD SHOT 200 to 400 pellets
The shot leaves the gun as a solid mass at a velocity of about 1100 ft/sec. Up to about 3 ft the
effect is of single shot but beyond that the lead pellets spread out and the effect is multiple shots.
The shell wad leaves the gun with the lead pellets and is projected for several feet before falling to
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 26
the ground. The end of the barrel is often restricted or CHOCKED in order to hold the shot
together over longer distances.
The entire charge (pellets/shots) when moving through the air, can be properly referred to as
the pattern, although strictly speaking, the pattern is registered relative distribution of the
entire load upon the target.
SHOT WADS
At a distance of 5 to 8 yards or more from the place of firing in the approximate direction of
fire, one can sometimes finds wads.
Wads are very important because at times, these wads serve to identify the gauge and type of
ammunition used. In many shotgun crimes, wads are recovered at the scene, sometimes also right
inside the body of the victim. Unburned gunpowder can sometimes be recovered. All these
should, of course, be preserved since wads and powder, together with pellets, serve as bases to
identify at least the maker of the ammunition, and the type and gauge of the shotgun used.
CARTRIDGE LIFE:
The life of well-made metallic small arms ammunitions could perhaps last for 10 years as its
average age but some ammo may also loose some of its strength in 5 or 6 years time.
Some may last 25 years or more depending on the conditions of storage. Damp warm climates
are worst.
In order to prevent the entrance of oil or moisture, it is a common practice to varnish the mouth
of the case before the insertion of the bullet and to put a ring of waterproofing around the joint
between the primer and the primer pocket.
CHAPTER V
BULLETS / SLUGS
INTRODUCTION:
A bullet, slug, missile, or projectile, is the metallic object attached to the free end of the
cylindrical tip of the cartridge case, propelled by the expansive force of the propellant, and
responsible in to production of damages in the target. In some instances bullets not metallic but
made of rubber, plastic, or even paraffin, but their uses are primarily confined to target practice.
ORIGIN:
The term bullet originated from the French word BOULETTE meaning a small ball. In
government parlance, a cartridge containing a bullet is still called BALL CARTRIDGE; from the
original terminology of the days when all bullets were balls.
Bullets in modern concept are projectiles propelled from rifled firearm, which is cylindrical
in shape.
The core of the slug is an alloy of lead, antimony and sometimes tin.
Armor-piercing bullets for small arms of similar material to the standard bullet, but in
addition to lead and antimony filler, a core of tungsten chrome steel which continues to penetrate
armor after the jacket and filler have been stripped away by contact with a resistant surface.
CLASSIFICATION:
A. Basically, there are two (2) kinds of bullets, and they can be classified under the following:
I. According to Mechanical Construction
01. LEAD BULLETS Are those bullets , which are made of lead or alloys of this metal (lead, tin
and antimony) which is slightly harder than pure lead.
Lead bullet must be lubricated to prevent the lead adhering into the bore that will interfere
seriously with the accuracy. This action is called LEADING
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 27
Lead Bullets generally used in revolvers. They are used in target shooting when they are
used in self-loading rifles they will melt.
02. JACKETED BULLETS Are those bullets with a core of lead covered by a jacket of harder
material such as gilding metal, a copper-alloy of approximately 90%. Some Europeans use steel as
jacket material.
The primary function of the jacket in a bullet to prevent adherence of metal (lead) to the
inside of the gun barrel.
--- Copper plated steel maybe used instead of gilding metal for the jacket of caliber .45 bullets.
Jacket of metal patch made of cupric nickel or gilding metal.
--- If jacketed bullets are used in revolvers, the gun barrel will be loosened or destroyed.
--- Keyhole shot the tumbling of the bullet in its flight and hitting the target sideways as a result
of not spinning on its axis.
RIFLED BULLETS:
There are many types of targets that can be destroyed by small missiles or projectiles. To
secure a maximum effect against each other, there are many types of bullets or shells. There are
five (5) principal types, two or more of which are combined into one bullet.
1. Ball bullets have soft lead cores inside a jacket and are used against personnel only.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 28
2. Armor Piercing bullets have hardened steel cores and are fired against vehicles and other
armored targets in general.
3. Phosphorous Flare or Tracer bullets - Contains a compound at the base usually barium
nitrates ,which is set on fire when the bullet is projected. The flash of smoke from this burning
projectile permits the flight of the bullet to be seen.
- This consists of an aluminum tip and is packed with incendiary (phosphorus) which
burns during flight. It is used to determine the direction of the fire. The speed of sound in air is
1,087 feet per second or 331.3 meters per second.
4. Incendiary bullets contain a mixture such as phosphorous or other material that can be set on
fire by impact. They are used against targets that will rapidly burn such as aircrafts or gasoline
depot.
5. Explosive (Fragmentary) bullets contain a high charge explosive. Because of their small size,
it is difficult to make a fuse that will work reliably in small arms ammunitions.
For this reason the use of high explosive bullets are usually limited to 20 mm. and above.
OTHER TYPES:
01. Plastic Bullet - used for target practice.
02. Bullet with Plastic Sabot The bullet together with the sabot travel up to the bore. The bullet
never comes in contact with the barrel and therefore there will be no rifling marks imparted in the
bullet but on the sabot. The front half of the sabot has six slits. As the sabot leaves the barrel it offers
resistance and the slit part of the sabot will fold backward, causing resistance and falls away.
At three feet, the sabot and bullet are still in line.
At 6 to 7 feet, they strike the target separately.
The sabot itself travels approximately 50 feet.
03. Bullet with Secondary Explosion The bullet may leave the barrel and upon reaching a certain
distance it produces secondary explosion and shrapnel splinters.
04. Pointed Bullet is more effective ballistically than the round ball of the same weight because
there is less surface presented to the air and thus the speed of the bullet is less retarded so quickly.
05. Dumdum Bullet is an out-moded bullet and generally misused.
06. Soft Point or mushroom Bullet will expand on striking an object and therefore produce
much more serious shock and have correspondingly greater stopping power.
Soft Point Bullets when fired from a high velocity rifle will expand upon striking a flesh
until it looks like a mushroom; hence, they are often called mushroom bullets. Such bullets are of
little effect than a full jacketed bullet in revolvers or automatic pistols, because the velocity is too
low to cause the bullet to expand.
07. Hollow Point Bullet a bullet with a cavity in the nose designed to increase the expansion
when it hits the target (sometimes called Express Bullet).
08. Metal Cased Bullet colloquially used to indicate either a metal patched or full-patched bullet.
09. Metal Patched Bullet any metal-jacketed bullet.
10. Steel Jacketed Bullet Bullet having soft steal jacket, often clad or plated with gilding metal to
prevent rusting and reduce frictional resistance in the bore.
Purpose of Bullets
.38 disability
.45 shocking/subdue, knocking effect
M16 fatal effect
Resistance of Cal 38 is 15,000 to 45,000 ft/pound
Buck shot- it ranges from 50 yards
CHAPTER VI
CARTRIDGE CASES / SHELL
Definition:
Is a tabular metallic or non-metallic container which holds together the bullet, gunpowder
and primer.
The cartridge case is the portion of the cartridge that is automatically ejected from the
automatic firearm during firing and this remains at the scene of the crime. This is a firearm evidence
that can help trace a particular firearm from which it was fired.
FUNCTIONS:
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 29
1. It serves as a means whereby the bullet, gunpowder and primer are assembled into a unit.
2. It serves as a water proof container for the gunpowder.
3. It prevents the escape of the gases to the rear as the sidewalls of the cartridge case are forced
against the walls of the chamber by the pressure. It serves as the gas seal at the breech end of the
barrel.
PARTS:
1. RIM serve the purpose of limiting the forward travel of cartridge into their chambers and this
also limit the clearance, if any, between the heads and the supporting surface of the bolt or
breechblock.
2. PRIMER POCKET performs triple functions:
a. holding primer securely in central position
b. providing a means to prevent the escape of gas to the rear of the cartridge; and
c. providing a solid support of primer anvils, without which the latter could not be fired.
3. VENTS OF FLASH HOLES is the hole in the web or bottom of the primer pocket through
which the primer flash imparts ignition to the powder charge.
4. The HEAD and BODY constitute the cork that plugs the breach of the barrel against the
escape of the gas.
5. NECK that part of the cartridge case that is occupied by the bullet.
6. CANNELLURES are the serrated grooves that are sometimes found rolled into the neck and
bodies of the cases at the location of the bullet bases to prevent the bullets from being pushed
back or loosened.
- It is a groove indentation of a cartridge case that holds the end of the bullet.
7. Crimp is that part on the mouth of a case that is turned in upon the bullet.
Two-Fold Function:
1. It aids in holding the bullet in place.
2. It offers resistance to the movement of the bullet out of the neck which affects the burning
of the gunpowder.
8. BASE the bottom portion of the case which contains:
a. The primer, which contains the priming mixture.
b. The shell head which contains the priming mixture.
c. The shell head which contains the headstamps, caliber and the year of manufacture.
9. SHOULDER that portion which support the neck.
10. EXTRACTING GROOVE the circular groove near the base of the case or shell designed for
automatic withdrawal of the case after each firing.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 30
Revolvers and shotguns normally have rimmed cartridges which stops them from sliding
through the chambers or breech, while self-loading pistol cartridge is generally rimless or semi-
rimmed, bearing instead a groove to provide grip for the extractor.
B.) Semi-rimmed designed to be used in the automatic weapons like pistols and submachine
guns such as Super .38, UZI 9 mm. These are the cartridge cases normally found at the crime
scene because they are automatically ejected for every firing of the firearm. And these cases
found at the crime scene are of essential in tracing the very firearm or weapon that fired them.
- It has a flanged which is slightly larger than the diameter of the cartridge case and a groove
around the case body just in front of the flange.
C.) Rimless cases wherein the diameter of the body of the cartridge is the same as the diameter
of the cartridge case.
- Used in automatic pistols, cal .45 Thompson Submachine guns, Cal .45 Grease gun.
- Automatically ejected from the firearms after every shot, like that of the semi-rimmed
type.
The cartridge cases or shells remain at the scene of the crime. The cases found thereat
helps in tracing the particular guns from which they were fired.
D.) Rebated It has an extractor flange which is less than the diameter of the cartridge case.
E.) Belted Case These have pronounced raised belt encircling the base of the cartridge.
CHAPTER VI
PRIMERS
Definition:
Refers to the portion of the cartridge which consists of a brass or gilding metal-cup
containing a highly sensitive mixture of chemical compound, which when struck by the firing pin
would detonate or ignite. Such action is called PERCUSSION.
Used for igniting the gunpowder. A blow from the firing pin on the primer cup compresses
the priming mixtures and this causes the composition to detonate or explode. This detonation or
explosion produces flame which passes through the vent of flash-hole in the cartridge case and
this ignites the gunpowder.
ORIGIN:
1807 Alexander John Forsyth Father of percussion ignition system. First one to conceive the idea
of using detonating compounds for igniting powder charges in small arms by percussion.
--- A Scotch Presbyterian Minister, chemist and hunter.
--- A well-known authority on firearms.
--- First successful priming mixture was one composed of potassium chlorate, charcoal and sulfur
in powder forum.
PARTS OF PRIMER
In a typical center-fire cartridge have four parts:
1. Primer cup container of the priming mixture. Made up of brass, gilding metal or copper.
2. Priming Mixture highly sensitive chemical mixture contained in the primer cup.
3. Anvil that portion of the primer against which the priming mixture is crushed by a blow from
the firing pin. Must be hard, rigid and firmly supported in order to provide the resistance necessary
to firing the priming mixture.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 31
rod for reloading purposes. Boxer-primed ammunition is almost exclusively used in commercial
ammunition and used mainly in North America.
B. BERDAN PRIMER ( two flash hole ) It was designed in 1867 by Colonel Hiram Berdan
of the U.S. Army Ordnance Department. In this system, the anvil is actually a part of the cartridge
case in the form of a small peg in the primer pocket. Around the anvil are a number of small flash
holes to permit the passage of the ignition flame from the primer to the propellant. Mostly used in
military ammunition.
C. BATTERY CUP SYSTEM It consists of a plain cup with no anvil, which fits into a
slightly larger inverted flange cup containing its own anvil. The flanged cap provides a rigid
support to the primer cup and anvil. The self-contained assembly fits into recessed pocket in the
base of the cartridge case. Battery cup primers are used exclusively in SHOTGUN ammunition.
4. Disc piece of small paper or disc of tin which is pressed over the priming mixture.
PRIMING COMPOUNDS:
Classes:
1.Corrosive primers e.g. Potassium chlorate if ignited produces potassium chloride, draws
moisture from the air and this moisture speeds the rusting and corrosion in gun barrels.
Advances in chemistry produce new compositions which potassium chlorate has been
eliminated.
CORROSION the chemical wear and tear of the inside of the gun barrel due to rust formation
or chemical reaction by the products of combustion after firing.
EROSION the mechanical wear and tear of the inner surface of the gun barrel due to
mechanical abrasion or sliding friction. Constant use of jacketed bullet.
2. Non-corrosive
Every manufacturer has his own formula
When WWI came, the standard mixture used by Frankford Arsenal known as FH 42 had the ff.
composition
Sulfur - 21.97%
Potassium Chlorate - 47.20%
Antimony Sulfide - 30.83%
A Typical rimfire primer used in Cal. 22 ammo. had the ff. composition obtained by chemical
analysis in the Frankford Arsenal lab.:
Potassium chlorate - 41.43%
Antimony Sulfide - 9.43%
Copper Sulpho-cyanide - 4.70%
Ground glass - 44.23%
Germans have their own composition Barium nitrate in the place of K-chlorate together with
the same picric acid to strengthen the mixture. Their formula:
Fulminate of mercury - 39%
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 32
Barium nitrate - 41%
Antimony sulfide - 9%
Picric Acid - 5%
Ground glass - 6%
Swiss army had been using non-corrosive primer since about 1911. This was based on the
formula of a Swiss inventor named Ziegler. Swiss formula:
Fulminate of mercury - 40%
Barium nitrate - 25%
Antimony sulfide - 25%
Picric Acid - 6%
Ground glass - 4%
CHAPTER VII
GUNPOWDER
DEFINITION : Refers to the propellant which when ignited by the primer flash is converted to gas
under high pressure and this propels the bullet or shot charge through the barrel and on to the
target.
Gunpowder, propellant, powder charge refers to the same thing.
EXPLOSIVES IN AMMUNITION
TWO (2) TYPES OF EXPLOSIVES
01. LOW EXPLOSIVES Have gradual pushing action. They do not destroy by their own
explosion. Low explosives propel or push shells from guns, or drive rockets through the air. They
help control the speed of the explosion. A low explosive going off resembles rapid burning. Each
grain of the explosive burns from the outside, like a log in a fireplace. The speed of the burning
depends on the size and shape of the grains. Used in gun ammunition called, propellant. Its
explosion lasts long enough to propel the shell out of the gun and send it to the target. Low
explosives include the Black and Smokeless powder.
02. HIGH EXPLOSIVES They are used to destroy, and do not propel or push. They go off
suddenly and shatter the shell, bomb, or torpedo. The speed of such explosion and detonation
cannot be controlled. Well known high explosives include dynamite or trinitroluene (TNT).
CHARACTERISTICS
- Oldest propellant powder
- Consist of irregular grains and have either a dull or shiny black surface.
- Produces grayish smoke and considerable residue is left in the barrel.
- Burns with reasonable great rapidity when ignited.
BLACK POWDER relies for its explosive properties on 3 qualities which are typical of all
explosives.
First, when ignited it will burn by itself without aid from the outside air.
Second, in burning, it gives off a large amount of gas.
Third, a considerable amount of heat is evolved.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 33
Most dangerous explosives to handle and store, because it can easily ignited by heat, friction,
flame or spark.
II. Smokeless Powder The term smokeless powder is a mismomer for they are neither powder
nor are they smokeless, the latter term being applied to them only because they do not give off
huge cloud of white smoke like the black powder.
--- most powerful propellants being used.
Double-base propellants are gray green to black in color and the grains are similar in size and
shape to the single-base propellants.
Almost all smokeless powder grains have a perfectly definite shape such as:
a. small squares d. strips
b. discs e. pellets
c. flakes f. perforated cylindrical grains
3. TRIPLE BASE PROPELLANT A type propellant powder which uses three principal
ingredients.
a. Nitrocellulose
b. Nitroglycerin
c. Nitro-guanidine
It was devised in an attempt to comprise between the low power single based powders
and high power but excessive heat of double base powders. The percentage of nitroglycerin
is small, but sufficient to give added power. The nitro-guanidine lowers the flame
temperature while still adding active explosive constituent. One of the virtues of triple based
powders is that it is entirely flashless thought it does not generate rather more smoke than
the other types.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 34
CHAPTER VIII
MAKING GUN BARREL
A barrel is made from solid composition steel. The first step in to drill a hole from cane end
through one end. The next step is to ream this hole very carefully to the exact bore diameter. This
reaming process leaves very circular marks round the barrel, caused in part by irregularities of the
cutting edge of the reamer and partly by little chips of steel that get caught by the reamer and drag
around it. A finished reamed bore before rifling looks smooth and glassy to the naked eye but when
examined by a high powered microscope these mark will show up in very pronounces fashion.
The reaming, process removes of the scars and scratches left by the drilling operation. After the
reaming has been finished the next step is to put in the rifling. There is a rod that fits the inside of
the bore and this rod has in the point of its circumference a small blade that scrapes away a part of
the metal broaching. After the rifling operation is completed, the barrel is lapped. Lapping is the
smoothening of the inner surface of the gun barrel. Polishing the inside of the barrel is like a mirror
with a polishing compound.
Some rifling methods used to make the rifling inside a gun barrel are:
1. BROACH-GANG SYSTEM
- A tool having a series of cutting edges slightly increasing height used to cut the spiral
grooves in a barrel. All grooves are cut with the single pass of the broach.
2. BROACH-SINGLE SYSTEM
- A non-adjustable rifling cutter which cuts all the grooves simultaneously, and is in a series
of increasing dimensions until the desired groove depth is achieved.
3. BUTTON SYSTEM
- A hardened metal plug, called a button, with a rifled cross section configuration. It is
pushed or pulled through a drilled and reamed barrel so as to cold form the spiral grooves to the
desired depth and twist. When the carbide button was first introduced, it was described as a
SWAGING PROCESS or SWAGED RIFLING.
4. HOOK-CUTTER SYSTEM
- A cutting tool which has a hook shape and only cuts one groove at a time.
5. SCRAPE SYSTEM
- A cutting tool which cuts two opposing grooves at a time.
6. SWAGE SYSTEM
- An internal mandrel with rifling configuration which forms rifling in the barrel by means
of external hammering. Also known as HAMMER FORGING.
Land and groove marks together are called rifling marks. Found on the cylindrical or
peripheral surface of the fired bullets and these are caused but the riflings inside the gun barrel.
Skid marks when the bullet first starts forward without turning, that before the bullet can
begin to turn, it moves forward a small distance and this makes the front of the groove in the bullet
wider than the rear part. The skidding is more pronounce in the revolver.
Stripping Marks scratches on the fired bullets due to worn out barrel which cause the
bullet to jump.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 35
MARKS FOUND ON FIRED SHELLS
1. Firing Pin Marks are generally found on the primer cup which is the central area of the base
of the cartridge. True in center fire cartridges.
2. Breech Face Marks are found generally on the base of the cartridge case.
3. Extractor Marks are mostly found on shells fired from pistols, rifles, shotguns and machine
guns.
4. Ejector Marks found on fired cartridges of automatic weapons and are located near the rim.
5. Shearing Marks called secondary firing pin mark, found in the primer near the firing pin
mark.
6. Chamber Marks mostly found around the body of the fired cartridge case and they are caused
by the irregularities in the inside walls of the chamber.
7. Pivotal Marks marks found on shell caused by turning of the cartridge.
8. Magazine Lip Markings markings found at the two points of the rim of the base of the shell
and these are caused by the magazine lips during the loading of the cartridges into the
magazine for firing.
These marks serve as a good guide for the firearm examiner in determining more or less the
relative position of the cartridge in actual explosion in the chamber of the suspected firearm
submitted for examination.
II. Individual Characteristics those that are determinable only after the manufacture of a
firearm.
These are the irregularities found in the inner surface of the barrel and on the breech face of
the breechblock of the firearm as a result of the failure of the tool beyond the control of man to
make them smooth as a mirror. When seen on the bullet or shell they run in the form of a parallel
scratches, striae or striations.
CATEGORIES:
-Caliber or gauge
-Land to land caliber
-Groove diameter measured from two opposite grooves.
Cartridge cases fired in revolvers there are two marks-the extractors and the firing pin.
What kind of firearm used? Individual characteristics
RIFLING are helical lines cut in the interior or the bore of gun barrel
Rifled weapons are distinguished by a spiral grooving or rifling on the side of the barrel.
This spins the bullet, marking it more stable in flight and giving greater accuracy.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 37
PURPOSE OF RIFLING
Is to impart a steady rotating motion of the bullet in its travel straight forwards nose on
towards the target.
To impart rotation/stability in the flight and greater penetration.
Pitch of rifling the number of inches traveled by the bullet to make one complete turn.
Caliber is the diameter of the inner surface of the barrel that is measured from land to land.
Twist of rifling the direction of twist whether right or to the left.
LANDS are the raised portion of the bore of the gun barrel.
--- the elevated portions between the grooves inside a rifled gun barrel.
COMMON CALIBERS
English (inches) .22 cal, .25, .30, .32, .38, .44, .45
Metric (millimeters) 5.5mm, 6.35, 7.65, 8, 9, 11.3, 11.4
Other types of calibers - .357, .380, .50
CONVERSION FORMULA
A.) mm (given) --- inches (problem)
given / 25.4
x 0.03937
B.) inches (given ---mm (problem)
given x 25.4
/ 0.03937
CHAPTER IX
CRIME SCENE SEARCH FOR BALLISTICS EXHIBIT
METHODS OF SEARCH
01. Strip Method of Search if the shooting took place in closed small area, this method is
applicable.
02. Double Strip Method If the shooting took place in the bigger area this method can be used.
03. Spiral Method the searcher follow each other in the path of a spiral beginning on the outside
and then spiraling in toward the center.
04. Wheel Method the searcher gathers at the center and proceeds in outward radii or spokes.
This procedure should be followed repeatedly depending on the size of the area.
05. Zone Method If shooting incident takes place in a bigger area, this method can be adapted.
The area is divided into zones and each zone one of the above four methods may be used.
This method is very practical in outdoor shooting or in cases of running gun battles. One
searcher may be assigned in one zone.
The investigator or the searching officer must be aware of those allied items or objects
that may be related to the use of firearms, such as:
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 38
1. holster 5. gloves
2. magazine (for automatic weapon) 6. masks
3. cartridge belts or holders 7. bullets
4. cartridge
TYPES OF SKETCHING
1. Open field sketch - outdoor
2. Open projection sketch - indoor
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 39
c. Make and serial number of the firearm investigator should mark his initials on the
butt or frame of the weapon for future identification.
10. At the crime scene, note down where the empty shells, bullets and/or firearms were found
and make a diagram to illustrate the same to show their relative distances and direction from the
of the victim. Photograph if possible.
11. Mark the empty cartridge cases inside or near the mouth by scratching the initials of the
investigator or the initials of the victim.
12. Mark the bullet at the ogive (or nose) by scratching the investigators initials or the victims
initials, but definitely NOT at the rifling marks (landmarks and groovemarks).
13. Mark the empty shotgun shells with indellible ink at the body.
14. The barrel of the barrel must be mark too.
15. After marking the empty shells and bullets, wrap them separately and individually
with soft tissue paper and note down on the wrapper where each was found, time, and date. The
purpose of wrapping them separately is to avoid being scratched during their carriage form the
crime scene and on to its place of depository.
16. When an empty shell was found at the scene of the crime, the presumption is that AN
AUTOMATIC PISTOL or AUTOMATIC WEAPON was used.
17. When no empty shell was found at the crime scene, the presumption is that a REVOLVER
was used.
18. In the bore of the barrel, the depressed portions are the grooves and the raised portions are
the lands.
19. On a fired bullet, it is the reverse, the landmarks are the depressed portions, and the groove
marks are the raised portions.
20. To determine the real direction of the rifling twist in a rifled barrel, peep thru the barrel,
particularly on the land and grooves and look away from you. If the land or the groove inclines to
the right, then it has a right twist, and if it inclines to the left, then the rifling twist to the left.
21. To determine the direction of the twist of a bullet, look on the bullet in an elongated position.
If the lands and grooves incline to the right, then the rifling twist is right. If the inclination is left,
then it is left.
22. It is the rifling of the bore that marks a fired bullet.
23. A fired bullet will acquire the class characteristics of the bore of the of the barrel from which it
was fired. Therefore, if the bore has a class characteristics of a .45 caliber, 6 lands, 6 grooves, right
twist, groove wider than the land, such characteristics will be marked on the bullet it fires.
24. So, if a fatal bullet will have the same class characteristics as the bore of the suspected gun, then
it is POSSIBLE that the bullet COULD have been fired from the suspected firearm or gun.
25. To determine definitely if the bullet above was fired or not from the suspected gun, then the
case must be sent to a FORENSIC BALLISTICS EXPERT who will conduct the proper examinations.
26. If two bullets do not have the same class characteristics, DEFINITELY and CONSEQUENTLY,
the bullets were NOT fired from the barrel.
CHAPTER X
MARKING PHYSICAL EVIDENCE
Identification is most easily determined by means of a mark or label, which has been placed
on the physical evidence.
The following steps are used when marking physical evidence or ballistics exhibits:
a. Use a distinctive mark such as initials of the recovering officer.
b. Do not use X for marking because X is a universal mark and almost everybody uses
it so much so that it is hard to distinguish one X from another X.
c. Record the mark used and the position of the mark on the object.
d. Record any serial number or other distinctive marks present on the object.
e. Whenever possible, mark the object itself, taking care not to damage or alter it.
f. Always mark the container in which the object is placed even if the object itself is already
marked.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 40
g. When tags are used, make corresponding entry in the tag and attach it securely to the
object.
*** Note: do not mark at the cylindrical or peripheral surface because in this portion contains the
rifling marks or striations.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 41
3. cleaning tissue or box
4. thick brown envelope/s
5. cotton
6. match box
2. Stereoscopic Microscope No camera attachment and no photomicrograph can be taken for court
representation.
- Close-up examination tampered serial numbers.
- For so-called orientation purposes.
4. CP-6 Comparison Projector - Very much similar with the bullet comparison microscope.
No eye strain because the magnified image appears on the large screen. What can be seen
in the screen can be photographed by any kind of camera.
5. Bullet Recovery Box Long box (12 x 12 x 96) tilled with ordinary cotton and separated into
sections by cardboard partitions.
6. Helixometer - Used in measuring pitch of riffling distance traveled by the bullet in one
complete rotation.
Charles E. Waite - after 5 years solid toil, had a formidable bank of information at his disposal. He
also realized that because of the wearing down of the machine tools, their marks on the inside of
the barrel, made during, the cutting of the rifling, out to be individual if a way could be found in
examining them. He explained the problem to a Physicist named JOHN H. FISCHER, who made
worked on the development of the CYSTOSCOPE, a medical instruments used to insert line tubes
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 42
carrying tiny lamps into the bladder and kidneys in order to facilitate their inspection without
resorting to an operation. A similar instrument, decided Fischer, would be ideal or Waites
purpose. After period of experiment Fischer came up with HELIXOMETER, a long hollow probe
fitted with, a lamp and magnifying apparatus at its tail end. With a few modifications the
Heliometers is still a fixture of every firearms laboratory.
ROBERT CHURCHILL the first modern British Firearm Examiner of real expertise. A sporting
gunmaker.
7. Micrometer similar in use as calipers
8. Caliper used for making measurements such as bullet diameters, bore diameter, barrel length,
etc.
9. Analytical or Torsion Balance Used to determine weights of bullets and pellets for possible
determination of type, caliber and make of firearms from which it was fired.
10. Onoscope small instrument sometimes used in examining the internal surface of the gun barrel
in determining the irregularities inside the bore of the gun barrel. It has a tiny lamp at the terminal
portion and is inserted inside the bore for internal examinations.
12. Electrical Gun Marker used in the laboratory for marking fired bullets, fired shells and firearms
submitted for examination.
13. Gunsmith Tools Generally used in the repair of firearms and also for marking physical
evidence like firearms, fired bullets, and fired shells.
TECHNIQUES OF EXAMINATION
Physical: Evidence bullets, cartridge cases and suspected firearms once submitted by the
requesting party will be physically examined to determine its markings or initials made by the
investigators for identification purposes.
Test Firing: The firearm is test fired from a bullet recovery box in order to obtain test bullets
and test cartridge cases. But before firing, the cartridge will be marked at the side of the case on the
nose portion of the bullet with letter T (test) followed by the last two digits of the serial number of
the firearm (e.g. T-77-1 to T-77-3) in their order of firing to distinguish the number 1 test from 2
and 3.
Microscopic Examination After the recovery of the test bullets and test cartridge cases, they
will be compared with the evidenced bullet and evidence cartridge cases under the bullet
comparison microscope to determine whether or not they have the congruency of striations or the
same individual characteristics.
Under the bullet comparison microscope, the two fired bullets or fired shells are examined
in JUXTAPOSITION that is, the two objects evidence and the test bullet are examined and
compared:
01. at the same time;
02. at the same plane or level;
03. at the same direction;
04. at the same magnification; and
05. at the same image.
FOR CONCLUSIVENESS OF FINDINGS, there shall be at least 3 TEST BULLETS that should be
compared.
First, 1 for comparison / preliminary
Second, 1 for confirmation
Third, 1 for conclusions
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 43
PERIPHERY - these are the sides of the bullet that are in contact with the inner surface of the barrel.
STRIATIONS - are individual characteristics of the cartridges found at the base portion and of the
side or the bullet that come in contact with the inner surface of the barrel.
The rifled gun barrel leave distinctive marks upon the bullet called STRIATIONS from the
Latin STRIA originally meant the fluting on an architectural column, and bullet striations
resemble these to a remarkable degree; even air weapons leave rifling striations on their pellets.
The only firearm that do not are smoothbore guns such as shotguns and antique weapons of the
flintlock type plus such home made weapons as replica guns which had their barrels bored
through.
TEST BULLETS are those recovered from bullet recovery box for comparison with the evidenced
bullets under the bullet comparison microscope.
Test firing of a weapon must be done in such a way that the bullet can be recovered
undamaged. For all jacketed bullets and most types of lead bullets, a cotton wad box or water trap
is used to stop the bullet. With a cotton wad box, as a consequence of its rotation, the bullet twists
itself up in the waste, which finally forms a ball around the bullet, and the velocity progressively
decreases until the bullet is finally held in the cotton waste.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 44
CHAPTER XI
PRINCIPLES IN FIREARMS IDENTIFICATION
The man who expect to appear in court as an expert on firearms should know as much as possible
about them and their ammunition, and about everything connected with their use and effects, for
he must realize that very likely an attempt will be made to discredit the extent of his knowledge
and if he is not the possessor of a lot of collateral information regarding matters of this kind, he
may himself the victim of his own lack of broader knowledge of his subject.
Two things mark by one and the same tool will bear the same markings; likewise two or more
things mark by different tools will have different markings.
TYPES OF PROBLEMS:
1. Given a bullet, to determine the caliber type and make of the firearm from which it was fired.
2. Given a fired cartridge cases, to determine the caliber, type and make of the firearm from which
it was fired.
3. Given a bullet and suspected firearm, to determine whether or not the bullet was fired from the
suspected firearm.
4. Given a fired cartridge case and suspected firearm, to determine whether or not the fired
cartridge case was fired from the suspected firearm.
5. Given two or more fired cartridge cases, to determine whether or not they were fired from the
same firearms.
6. Given two or more bullets, to determine whether or not they were fired from the same firearms.
7. Given a firearm, to determine whether the firearm is serviceable or not.
NOTE: Bullets and even fragments of bullets may be used to determine the type of the
weapon used, both from the sized and weight of the projectile and an examination of the striations
on the outside surface. Thus, for example, the number, direction of twist, and measurements of
lands and groove markings can be useful in determining the type, make, model and caliber of
firearm.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 45
LEGAL PROCEDURES Court Trials Wherein the Ballistics report of the Firearm Examiner the
ballistic exhibits fired bullets, firearms and allied exhibits are presented during the trial of the case
in a Court or Justice. It also includes the presentation of the Ballistics Expert, to give testimony
regarding his findings/conclusion.
LIMITATIONS:
Shooting incidents resulted to murders, homicide, physical Injuries, bank robberies and
indiscriminate firing of guns continue to exist. The suspects remain unidentified and the only traces
that could possibly identity them are the bullets extracted from their victims, shell and bullets
recovered from the crime scene.
The only means the police investigators could rely is the scene of firearms identification or
Forensic Ballistics at the Police Crime lab. However, the examination of the submitted ballistics
specimens, no matter how complicated could only be examined with in the province of the so-
called 7 problems in forensic Ballistics or firearms Identification.
One must realize, however that Forensic Ballistics or the science of Firearms Identification
remained essentially unchanged since 192O, using the Traditional Bullet Comparison Microscope.
The process is so slow and painstaking and because the evidence is often
deformed/mutilated and difficult to view on the microscope, examiners fatigue cuts down on tie
number of specimens that can be processed or examined.
It takes Firearms Examiners nearly 30 minutes to one hour to several days before making a
conclusion. The most difficult task for an examiner to accomplish is to identify bullet or shell was
fired. Cases where there is no firearm submitted.
BULLETPROOF is a field proven automated bullet image analysis system. It captures the image
of the microscopic features found on a fired bullets surface in a highly repeatable manner. The
markings or signature are analyzed by the computer and can be compared to those of other fired
bullets or to an entire database if fired.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 46
Bulletproof and Brasscatcher together form a fully integrated and automated image analysis
system that permits firearms examiners to enter and review large number of fired bullets and fired
cartridge cases and cross reference hits made from each system within seconds.
Both system have been designed to be simple to operate, no previous computer experience
is required. The firearm Examiner interface utilizes minimal typed commands and is extremely
user friendly.
The systems are fully networkable. A remote site can be connected with a central Hub
system, the Central Hub System can link to a Regional database server and the regional database
serve can be connected to a National Site. This approach interlinks data from different jurisdictions
into one powerful database.
Bulletproof and Brasscatcher represent a giant leap forward in technology for us,
Criminologists and the Forensic Firearms Examiners. These are the tools we need to effectively
combat crime achieving measurable benefits in terms of efficiency.
Together, Bulletproof and Brasscatcher represents the new generation of Technology in the
field of forensic firearms identification. This program will become unbeatable team in our war
against crime identification. This program will become unbeatable team in our war against crime
by linking previously unlikable crimes, generating leads for investigators, efficiently compiling
searching vast database for possible hits, exchanging electronic evidence with other similar
installations and complementing the time proven comparison microscope.
These systems can make multiple matches in about 5 seconds, the system can be used to
trace bullets and shells that will link criminals, especially serial killers to several unsolved crimes.
The systems would uncover several identified killers, or, at the very least, a gun that has been
passed from one hand of one killer to another.
Criminologists, consider these systems as technological wonders that catapults forensic
ballistics from nineteenth century to the twenty first.
Criminologists who worked and devoted their time and efforts in this discipline must
recognized that peace and order requires law enforcement agencies particularly the Police Crime
Laboratory to be fully equipped and well trained scientifically in the modern methods of
combating crimes in all its form. Classroom instructors are not all that required to become efficient.
Suitable and adequate On-the-Job-Training in the Crime Laboratory, authoritative books,
references and other materials are needed to update the scientific knowledge and skills of the police
personnel and criminologists in crime detection and investigation.
[[The Only Way for Evil to Triumph is when Good Men DO Nothing Burke] rnresurreccion 2015] Page 47