Professional Documents
Culture Documents
28/12/2010
ZXG10-BTSV2.0
ZXG10-BS30(V1.2)
ZXG10-M8206
ZXG10-BS21 (V2.0)
ZXG10-OB06
ZTE CABINETS
ZTE CABINETS
28/12/2010
1161
69 43 31 27
ZTE Network
ZTE CABINETS
WORKING PRINCIPLE
28/12/2010
RF Unit
interface
S Control signal
System
C clock
System clock
Heat exchanger
ZTE CABINETS
WORKING PRINCIPLE
28/12/2010
RF Unit
interface
S Control signal
System
C clock
System clock
Downlink:
The BTS receives data from BSC, including voice and signaling
Power Supply Module
data.
The transmission unit sends signaling data to the operation & maintenance unit for processing.
220V
The voice data are then sent to baseband processor for processing of rate conversion,
encryption and interleaving. Heat exchanger
Data are then sent to RF unit for modulation to high-frequency signals.
Finally, data are then transmitted through the antenna feeder processor.
ZTE CABINETS
WORKING PRINCIPLE
28/12/2010
RF Unit
interface
S Control signal
System
C clock
System clock
Uplink:
The antenna feeder processor receives the RF signals from the MS.
Power It then Module
Supply sends these signals to
the RF unit to 220V
convert into digital signals.
The signals are then transmitted to baseband processor for rate signals conversion, decryption
and de-interleaving. Heat exchanger
After conversion to the code pattern, suitable for long-distance transmission, the signals are
sent to the BSC through the Abis interface.
ZTE CABINETS
Knowledge sharing sessions
28/12/2010
ZXG10-BTSV2.0
ZXG10-BS30(V1.2)
ZXG10-M8206
ZXG10-BS21 (V2.0)
ZXG10-OB06
ZTE CABINETS
Hardware Structure
BTSV2.0
28/12/2010
MMI
TR/ETRM1
Abis A Um
BSC CMM TR/ETRM2 E
M
PDM TR/ETRM3
FCM
BTM
ZTE CABINETS
Hardware Structure
BTSV2.0
28/12/2010
MMI
The CMM TR/ETRM1
(Control & Maintenance
Module) performs the following functions:
Abis interface processing A
Abis BTS operation & maintenance Um
BSC CMM TR/ETRM2
Clock synchronization and generation
E
M
Collection of internal/external alarms
Fan management and the
PDM TR/ETRM3
active/standby function
FCM
BTM
ZTE CABINETS
Hardware Structure
BTSV2.0
28/12/2010
MMI
The TRM/ETRM ( Transceiver Module ) TR/ETRM1
performs the following functions:
Runs and Controls radio channels in A
Abis
GSM system Um
BSC CMM
Sends/receives radio channel data
TR/ETRM2 E
Modulates/demodulates baseband M
signals on the radio carrier frequency
PDM
Sends/receives radio carrier signals and TR/ETRM3
collects alarms of the fans and AEMs.
FCM
BTM
ZTE CABINETS
Hardware Structure
BTSV2.0
28/12/2010
MMI
TR/ETRM1
Abis A Um
BSC CMM TR/ETRM2 E
M
PDM TR/ETRM3
ZTE CABINETS
Hardware Structure
BTSV2.0
28/12/2010
MMI
TR/ETRM1
AEM (Antenna Equipment Module) provides
Abis the following functions: A Um
Combines the transmit signals of multiple
BSC CMMcarriers. TR/ETRM2 E
Provides bidirectional signal channels from M
the BTS to the antenna for the transmitting
PDM band and from the antenna
TR/ETRM3to the BTS for
the receiving band.
Gives an alarm when the VSWR of the
FCM antenna port deteriorates.
Suppresses the interference out of the
working band and spurious emission.
Flexibly configures carriers.
BTM Implements diversity receiving.
ZTE CABINETS
Hardware Structure
BTSV2.0
28/12/2010
MMI
TR/ETRM1
Abis A Um
BSC CMM TR/ETRM2 E
M
PDM The PDM (Power Distribution Module)
TR/ETRM3
performs the following functions:
Distributes -48 V DC power to all the
modules
FCM Provides overload protection
Stabilizes the input power
BTM
ZTE CABINETS
Hardware Structure
BTSV2.0
28/12/2010
MMI
TR/ETRM1
FCM
BTM
ZTE CABINETS
Knowledge sharing sessions
28/12/2010
ZXG10-BTSV2.0
ZXG10-BS30(V1.2)
ZXG10-M8206
ZXG10-BS21 (V2.0)
ZXG10-OB06
ZTE CABINETS
Hardware Structure
BS30(V1.2)
28/12/2010
TSM DPM
HW
signal
TRM LNA
Optical
interface Backplane
STM
Receiving RX
E1 CMM filter
Dup
TX
Internal
FAN
PWM HTM
AC 220V
ZTE CABINETS
Hardware Structure
BS30(V1.2)
28/12/2010
TSM DPM
HW
signal
TRM LNA
Optical
interface Backplane
STM
Receiving RX
E1 CMM filter
Dup
TX
AC 220V
ZTE CABINETS
Hardware Structure
BS30(V1.2)
28/12/2010
TSM DPM
HW
signal
TRM LNA
Optical
interface Backplane
STM
Receiving RX
E1 CMM filter
Dup
TX
AC 220V
ZTE CABINETS
Hardware Structure
BS30(V1.2)
28/12/2010
TSM DPM
HW
signal
TRM LNA
Optical
interface Backplane
STM
Receiving RX
E1 CMM filter
CMM (Controller & Maintenance Module ) Dup
provides such functions as Abis interface
processing, BS operation &
maintenance, clock synchronization and
TX
generation, and internal/external alarm
collection and processing. CMM consists of
a control O&M board.
Internal
FAN
PWM HTM
AC 220V
ZTE CABINETS
Hardware Structure
BS30(V1.2)
28/12/2010
TSM DPM
HW
signal
TRM LNA
Optical
interface Backplane
STM
Receiving RX
E1 CMM filter
The ZXG10 BS30 supports built-in SDH Dup
transmission equipment, which is
implemented by configuring STM.
The STM is the T150 researched and TX
manufactured by ZTE. T150 provides the
ZXG10 BS30 with 155 Mbits/s SDH
interface, providing diversified BS
transmission interfaces.
Internal
FAN
PWM HTM
AC 220V
ZTE CABINETS
Hardware Structure
BS30(V1.2)
28/12/2010
TSM DPM
HW
signal
TRM LNA
Optical
interface Backplane
STM PWM (Power Supply Module ) provides
Receiving RX
rectification, filtering and voltage
E1
filter
CMM stabilizing protection of 220 VAC (single-
Dup
phase three-lines), supplies 220 VAC for
HTM, TSM, STM and internal/external
fans, and provides 220 VAC input
over/under-voltage dry contact alarm. TX
Internal
FAN
PWM HTM
AC 220V
ZTE CABINETS
Hardware Structure
BS30(V1.2)
28/12/2010
TSM DPM
HW
signal
TRM LNA
Optical
interface Backplane
STM
Receiving RX
E1 CMM filter
Dup
TX
HTM (Heater Module) consists of a heater
and a fan. It serves to control internal
temperature and ensure the normal
operation of the equipment.
Internal
FAN
PWM HTM
AC 220V
ZTE CABINETS
Knowledge sharing sessions
28/12/2010
ZXG10-BTSV2.0
ZXG10-BS30(V1.2)
ZXG10-M8206
ZXG10-BS21 (V2.0)
ZXG10-OB06
ZTE CABINETS
Hardware Structure
M8206
Delay ALM
LMT
3E1/T1
Abis
ODU
48V 48V
ZTE CABINETS
Hardware Structure
M8206/RTU
28/12/2010
MDUP MDUP
MPAU
48V
ZTE CABINETS
Hardware Structure
M8206/RTU
28/12/2010
48V
ZTE CABINETS
Hardware Structure
M8206/RTU
28/12/2010
MDUP MDUP
MPAU (Micro Base Station Power
Amplifier Unit) is power amplifying
unit and amplifies the downlink
signal power. MPAU consists of two MPAU
power amplifier boards which are
installed on the bottom of base
station cabinet respectively.
M
R
P
I MTRB
W
B
R
48V
ZTE CABINETS
Hardware Structure
M8206/RTU
28/12/2010
MDUP MDUP
MPAU
This unit works as a duplexer and
consists of transceiver duplexer,
antenna interface VSWR detection
unit and Low Noise Amplifier
RTU Interface Board
M (LNA). It detects VSWR alarms in
three levels
P
MTRB
W
R
48V
ZTE CABINETS
Hardware Structure
M8206/RTU
28/12/2010
MDUP MDUP
MPAU
48V
ZTE CABINETS
Hardware Structure
M8206/CTU
28/12/2010
CIB
PWR
MCMB
T150
48V
IDU
ZTE CABINETS
Hardware Structure
M8206/CTU
28/12/2010
ZTE CABINETS
Hardware Structure
M8206/CTU
28/12/2010
CIB
PWR Board)
CIFB (CTU Interface
implements the signal conversion MCMB
between CMB and the bottom
interface. 5E1/T1 Test MMI
48V
Heater MEIB
5E1/T1
T150
48V
IDU
ZTE CABINETS
Hardware Structure
M8206/CTU
28/12/2010
ZTE CABINETS
Hardware Structure
M8206/CTU
28/12/2010
CIB
T150 is a PWR
small capacity AU-4 path STM-1
level SDH equipment. It is usually used MCMB
outdoors and is the auxiliary transmission
equipment of GSM and CDMA BTSs. The
function and interfaces are optimized5E1/T1
Test MMI
according to the48V actual requirement of
GSM and CDMA. It provides HeaterSTM-1 MEIB
(155520 Kbps) link, which is equal to the
capacity of four E1 links. 5E1/T1
T150
48V
IDU
ZTE CABINETS
Knowledge sharing sessions
28/12/2010
ZXG10-BTSV2.0
ZXG10-BS30(V1.2)
ZXG10-M8206
ZXG10-BS21 (V2.0)
ZXG10-OB06
ZTE CABINETS
Hardware Structure
BS21 (V2.0)
28/12/2010
BTM
TRM
B Abis T
AEM
S M CMM Um interface
C M
TRM
PSM
Heater
ZTE CABINETS
Hardware Structure
BS21 (V2.0)
28/12/2010
BTM
TRM
B Abis T
AEM
S M CMM Um interface
C M
TRM
The CMM (Controller & Maintenance
PSM
Module) implements such functions as
Abis interface processing, BTS operation &
Heater
maintenance, clock synchronization and
generation, internal/external alarm
collection and processing.
ZTE CABINETS
Hardware Structure
BS21 (V2.0)
28/12/2010
BTM
TRM
B Abis T The BTM (Backboard Transmission
AEM
S M CMM
Module) is responsible for transmitting Um interface
ZTE CABINETS
Hardware Structure
BS21 (V2.0)
28/12/2010
BTM
TRM
B Abis T
AEM
S M The TMM CMM (Transmission Management Um interface
Module) is an outsourcing device, and the
C M BS21 only provides one standard chassis
(19 inches 3U) used forTRM the built-in
PSM and other transmission
SDH, microwave
equipment.
Heater
ZTE CABINETS
Knowledge sharing sessions
28/12/2010
ZXG10-BTSV2.0
ZXG10-BS30(V1.2)
ZXG10-M8206
ZXG10-BS21 (V2.0)
ZXG10-OB06
ZTE CABINETS
Hardware Structure
BS21 (V2.0)
28/12/2010
BTM
TRM
B Abis T
AEM
S M CMM Um interface
C M
TRM
PSM
Heater
ZTE CABINETS
Knowledge sharing sessions
28/12/2010
ZXG10-BTSV2.0
ZXG10-BS30(V1.2)
ZXG10-M8206
ZXG10-BS21 (V2.0)
ZXG10-OB06
Thank you!