Professional Documents
Culture Documents
Submittal/Transmittal
TRAN #: 74
Edwards Lifesciences, LLC Issued Date: 1/8/2018
Project ID #: EDW2017 Req. Response Date: 1/15/2018
Job ID #: C1727 - Edwards Lifesciences - THV Production Cleanro
TO: FROM:
Ewing Cole Cannon Building
15231 Laguna Canyon Rd., Suite 200 1861 E. Miraloma Ave.
Irvine, CA 92618 Placentia, CA 92870
Contact: Gary Mangham Contact: Eddie Nahigan
Phone #: (949) 417-7550
Facsimile #:
ELECTRICAL SUBCONTRACTOR
Bergelectric Corporation
650 Opper Street
Escondido, CA 92029
GENERAL CONTRACTOR
Cannon Building
1861 E. Miraloma Ave.
Placentia, CA 92123
ARCHITECT ENGINEER
Ewing Cole Ewing Cole
15231 Laguna Canyon Road, Suite #200 15231 Laguna Canyon Road, Suite #200
Irvine, CA 92618 Irvine, CA 92618
650 Opper Street, Escondido, CA 92029 - Tel (760) 746.1003 Fax (760) 741.0918 - License No. C10-85046
C1727 ELS THV
16010-10 Submittal
FOR REVIEW Page 2 of 110 01/08/2018
TABLE OF CONTENTS
Network Lighting Controls
Specification Section: 26 09 43
TAB # 1
Lighting Control
Specification Section: 26 09 43
C1727 ELS THV
16010-10 Submittal
FOR REVIEW Page 5 of 110 01/08/2018
Controls Submittal
Job Name:
EDWARDS LIFESCIENCES
THV
Prepared For:
BERGELECTRIC
Date:
JANUARY 5, 2018
C1727 ELS THV
16010-10 Submittal
FOR REVIEW Page 6 of 110 01/08/2018
OVERVIEW
The Fresco Power Supply (FCS PS10) is a Class 2 low voltage power supply intended to
power a single Fresco Touchscreen, or other 24VDC Acuity Controls devices. The FCS PS10
is intended for use with 120-277V, 50/60Hz circuits.
FEATURES
FCS PS10 Power Supply
Low Voltage Power Supply
sȩ Provided with Fresco touchscreens
sȩ Available separately for use as low voltage power supply for Acuity Controls equipment
sȩ 24VDC output, Class 2 Circuit
sȩ 120-277V, 50/60Hz input
sȩ Supplies 10W@ 40°C, 7W@50°C FCS PS10
Suitable for Ple
sȩ Consumes 12W@120V, 14W@277V INPUT
num Use
OUTPUT
sȩ UL Listed (E110912) BLK/ORG: HOT Class 2 Circuit
ENVIRONMENTAL
24VDC
50/60Hz
10W max < 40º
0.2A max C/104ºF
7W max < 50º
C/122ºF
sȩ Maximum Ambient : 122°F/50°C NG ! WARNI
DISCONNECT POW
ER BEFORE SER
sȩ Minimum Ambient : 32°F/0°C VICING
Warranty
Two-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
DIMENSIONS (inches/mm)
3 1/2 1 13/16
(89) (46)
DISCONNECT POWER BEFORE SERVICING
10W max < 40ºC/104ºF
888.535.2465
*228MH0
Assembled in USA
7W max < 50ºC/122ºF
RED: 24VDC
BLK: GROUND
Class 2 Circuit
OUTPUT
PS10
Suitable for Plenum Use
24VDC
WARNING
2 9/16
(65)
FCS
120-277V
INPUT
0.2A max
50/60Hz
WHT: NEUTRAL
GRN: GROUND
E130839
!
BLK/ORG: HOT
ORDERING INFORMATION
Example: FCS PS10
Series Model
FCS Fresco Control System PS10 10W Power Supply
Acuity Brands | One Lithonia Way, Conyers Ga, 30012 PHONE : (800)-535-2465 www.AcuityControls.com ©2015 Acuity Brands Lighting, Inc. All rights reserved. 4/22/15 Sheet #: FCS PS10 1 of 2
FCSfor PS10
Plenum Use
Suitable FCSfor PS10
Plenum Use
INPUT OUTPUT Suitable
Class 2 Circuit INPUT OUTPUT
Class 2 Circuit
BLK/ORG: HOT RED: 24VDC
BLK/ORG: HOT RED: 24VDC
GRN: GROUND
BLK: GROUND GRN: GROUND
WHT: NEUTRAL BLK: GROUND
WHT: NEUTRAL
120-277V 24VDC
120-277V 24VDC
50/60Hz 10W max < 40ºC/104ºF
50/60Hz 10W max < 40ºC/104ºF
7W max < 50ºC/122ºF
0.2A max
LOW 0.2A max 7W max < 50ºC/122ºF
! WARNING ! WARNING
DISCONNECT POWER BEFORE SERVICING VOLTAGE DISCONNECT POWER BEFORE SERVICING
OUTPUT
888.535.2465 888.535.2465
*228MH0 *228MH0
Assembled in USA E130839 Assembled in USA
E130839
LOW
LINE LINE VOLTAGE
VOLTAGE VOLTAGE WIRING
WIRING WIRING COMPARTMENT
COMPARTMENT COMPARTMENT
WIRING CONNECTIONS
RED
BLACK
RED
+24VDC
BLACK WHITE
888.535.2465
*228MH0
Assembled in USA
7W max < 50ºC/122ºF
RED: 24VDC
BLK: GROUND
Class 2 Circuit
OUTPUT
PS10
Suitable for Plenum Use
24VDC
NETWORK
WARNING
DETACHABLE
FCS
PIGTAIL HARNESS
120-277V
INPUT
0.2A max
50/60Hz
WHT: NEUTRAL
GRN: GROUND
E130839
!
BLK/ORG: HOT
BLACK/ORANGE
H
120/277 VAC FRESCO TOUCHSCREEN
N
WHITE GREEN (BACK VIEW)
Acuity Brands | One Lithonia Way, Conyers Ga, 30012 PHONE : (800)-535-2465 www.AcuityControls.com ©2015 Acuity Brands Lighting, Inc. All rights reserved. 4/22/15 Sheet #: FCS PS10 2 of 2
OVERVIEW
OpenADR is a standard protocol that electrical utility providers can use to communicate demand
response signals using a common language over Internet. The nADR client allows an nLight and/or
XPoint Wireless system to integrate with an OpenADR 2.0a Demand Response Automation Server
(DRAS). This device functions by communicating with a configured OpenADR DRAS to retrieve live
power demand information from the utility company and automatically activate load shed profiles
according to pre-configured user settings. The device supports four demand response levels:
None, Moderate, High and Special; allowing a user to define load shed strategies for each mode.
nADR requires nGWY2 to activate load shed Profiles on nLight and/or XPoint Wireless systems.
FEATURES nADR
• Automated demand response and load shed capabilities for nLight and/or XPoint Wireless Demand Response Client
systems Interface
• Enables 2013 CA Title 24 compliance1
• Enables LEED Version 4 compliance. Qualifies building for a 2-point credit²
• Acuity Controls Virtual End Point (VEN)³ to Open Automated Demand Response 2.0a
(OpenADR) Demand Response Automation Server (DRAS)
• Supports four demand response levels (None, Moderate, High, Special)
• Supports integration through proxy servers, if required
NOTES
1. http://www.openadr.org/index.php?option=com_content&view=article&id=8
1:openadr-and-title-24&catid=21:press-releases&Itemid=121 The code states
that demand responsive controls and equipment shall be capable of receiving
and automatically responding to at least one standards-based messaging protocol
such as OpenADR. For example, in response to a DR signal, buildings larger than
10,000 square feet will have to automatically reduce their lighting power by at
least 15 percent below the building’s maximum lighting power.
2. http://www.usgbc.org/node/2613001?return=/credits
3. A VEN is also referred to as a DRAS client; Acuity Controls supports the OpenADR
simpleDRAS client mode UTILITY
DRAS
SPECIFICATIONS 1 2 3
SERVER
Size: 2.76” W x 1.06” H x 3.94” D (7.0 cm x 2.7 cm x 10.0 cm) nLight Gateway
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nADR Example: nADR L400
Series
nADR L400 Supports up to one (1) nGWY2 L400 version nLight Gateway
nADR Supports up to five (5) nLight Gateways (nGWY2 or nGWY2 L400)
nADR - TN-802
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 1
OVERVIEW
The nLight Bridge increases the number of lighting control zones in an nLight system. This ability
stems from the fact that each Bridge has 8 RJ-45 ports into which zones of daisy-chained nLight
devices can connect. The Bridge also is an integral component of the communication backbone in
an nLight network. Fundamentally, Bridges act as hubs by aggregating traffic from the connected
downstream zones and placing it onto the backbone. They also act as routers by forwarding
information from the backbone out to the applicable downstream zones.
FEATURES
• Communicates with nLight Network nBRG 8
• Remotely configurable/upgradeable 8-Port nLight Bridge
• Push-button programmable
• Green LED indicators for each Port
• Redistributes bus power between ports
• Supports up to 128 devices per port
SPECIFICATIONS
Dimensions: 4.90” H x 4.90” W x 1.05”D
Color: White
Mounting: 4” x 4” square box
nLight Network Ports: (8) RJ-45 Electrical
Input Voltage: 15-24 VAC/VDC
Input Current: 60 mA
Bus Power Contribution: ~90mA total (if powered via PS 150)
Max Input Current/Port: 40mA (e.g. from a connected nPP16)
Max Output Current/Port: 40mA (assumes sufficient bus power is present from combination
of local power supply and other connected zones with net positive
bus power)
Recom’d Power Supply: PS 150 via terminal connections (or PS 150 347)
RoHS Compliant, Title 24 System Component
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nBRG 8 Example: nBRG 8 KIT
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 2
DETAILED DIAGRAM
nGWY2 CTRL
LAN 1
2
3
Commisioning Card
Serial #
nGWY2
GWY2 GFX
SENSORVIEW 1 8
2 7
5 6 7 3 4 5 6 4 5 6 7 3 6
4 5
nBRG 8 nBRG 8 nBRG 8
1 2 3 4 1 2 1 2 3
NETWORK CONFIGURATION
An nLight network backbone consists of one or more Bridges and a Gateway (nGWY2 CTRL & nGWY2 GFX) communicating over CAT-5e wired connections. The
architecture can be topology-free, however wide branching backbone networks are recommended over linear runs. Any one or more RJ-45 ports on a Bridge
may be used to connect to other Bridge or Gateway devices.
Note: A maximum of 9 bridges may be used in a row (ie: bridge jumps from the gateway to the last bridge should remain less than 9).
PROGRAMMING
Refer to included instructions on LED indications and push button functionality.
nBRG - TN-701
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 2 of 2
OVERVIEW
The nCM xx RJB family of nLight ceiling/surface mount occupancy sensors provide a range of
networked sensor solutions for applications with finished ceilings (e.g. ceiling tiles, sheetrock,
plaster). nCM xx RJB family sensors utilize 100% digital Passive Infrared (PIR) detection and
are available with several lens options, providing flexibility for multiple mounting height and
coverage pattern requirements. Dual technology occupancy detection can also be added as an
option for applications where occupants are stationary for long periods of time. All sensors have
integrated on/off photocells as a standard feature, with automatic daylight harvesting/dimming
control as an available option. Additionally, nCM xx RJB family sensors are also available with
an optional auxiliary low voltage relay for simple integration with a BMS system or other building
nCM xx RJB
system. nCM PDT xx RJB
nCM xx RJB family sensors are powered via the nLight network bus and typically communicate
with one or more nLight enabled luminaires (e.g. Lithonia VTLED Series) or nLight relay/dimming
packs to enable control of fixtures individually or in groups. These configurations work standalone
and do not require a connection to a larger nLight network.
FEATURES
• 100% digital PIR detection
• Integrated photocell standard (disabled by default) — Photocell views down through sensor
lens and when enabled provides two selectable modes of operation
– On/Off mode: Photocell has full on/off control during periods of occupancy nCM
nCM 9 RJB
– Inhibit mode: Photocell can prevent lights from turning on if adequate daylight is available, nCM PDT 9 RJB
but cannot turn lights off
• Optional dimming photocell (ADCX option)
• Optional auxiliary low voltage relay (AR option) for dry contact output - relay only tracks
occupancy by default, ignoring switch and photocell commands
• LED status indicator
• Adjustable settings (e.g. occupancy time delays, photocell set-points) via push-button or
SensorView software application
• Broadcasts occupancy and photocell information over a local nLight channel nCM 10 RJB
• Remotely upgradeable firmware nCM PDT 10 RJB
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
nCM 6 RJB
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nCM xx RJB Example: nCM PDT 9 ADCX RJB
Series / Detection Coverage Type Options (See Below) RJ45 Port Location
nCM PIR Detection 9 Small Motion 360° RJB Rear RJ45 (CAT5e patch cable & RJ45
nCM PDT Dual Tech (PIR/ Microphonics) 10 Large Motion 360 ° splitter included)
6 High Mount 360° (not available with PDT version)
[blank] On/Off Photocell (disabled by default) [blank] None [blank] Single Time Delay [blank] Standard
ADCX Automatic Dimming Control (of remote dimming output) AR Low Voltage Aux. Relay 2P Dual Time Delay LT Low Temp / High Humidity
NOTES:
1. For information on models with side RJ45 ports, see website
2. Not available with AR or ADCX options
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 3
SPECIFICATIONS
Size: 4.55” Dia. (11.56 cm) 1.55” Deep (3.94 cm) nLight Bus Power Consumption: ~3mA
Weight: 6 oz nLight Network Connection: 2 RJ-45 Ports (via an included RJ-45
Mounting: Ceiling Tile / Sheetrock Surface, 3.5” Octagon splitter)
Box, Single Gang Handy box Relay Rating (AR option only): 1A @ 24 VAC/VDC (resistive only)
Color: Matte White ROHS Compliant, Title 24 Component
Wires / Cables: (1) CAT5e patch cable, 1ft (factory installed)
(2) 20 AWG wires (AR option only)
COVERAGE PATTERNS
SMALL MOTION 360º (Model # nCM 9/nCM PDT 91)
3.7 12
9.1 6 3 0m 3 6 9.1
30 20 10 0 ft 10 20 30
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 2 of 3
TYPICAL APPLICATIONS
nCM xx RJB
CAT-5e Splitter
(included)
nCM xx RJB
or
nCM xx ADCX RJB
nLight Enabled
Luminaire
TYPICAL APPLICATIONS
The following instructions are for mounting sensor directly to a ceiling tile or sheetrock
surface. Sensor’s mounting holes also align with standard round fixture or single gang
handy box (screws not provided).
1. Using template included with unit, mark spots on ceiling tile/sheetrock for cable hole
to/from nLight
and mounting anchors/screws
2. Drill 1/2” hole through ceiling surface at location indicated on template Zone
3. Insert provided anchors into ceiling surface at locations indicated on template CAT-5e CAT-5e
4. Remove provided RJ-45 splitter from sensor’s attached CAT5e cable and then thread
cable (and low voltage wires if -AR option included) through hole from underside
5. Mount sensor to anchors using two screws provided CAT-5e Splitter
CAT-5e
6. Attach provided RJ45 splitter device (model CAT5 Y) above ceiling to cable from sensor
(see diagram on right) BRN
7. Interconnect CAT-5e cables to/from rest of nLight zone to RJ45 splitter - AR option
BRN
8. Once power is received via CAT-5e connection, all devices in zone will automatically (contact closure
begin functioning together according to each device’s defaults
9. Install decorative sensor lid by rotating clockwise
10. Refer to included instruction card for default settings and directions on push-button
programming.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 3 of 3
OVERVIEW
The nCM xx RJB family of nLight ceiling/surface mount occupancy sensors provide a range of
networked sensor solutions for applications with finished ceilings (e.g. ceiling tiles, sheetrock,
plaster). nCM xx RJB family sensors utilize 100% digital Passive Infrared (PIR) detection and
are available with several lens options, providing flexibility for multiple mounting height and
coverage pattern requirements. Dual technology occupancy detection can also be added as an
option for applications where occupants are stationary for long periods of time. All sensors have
integrated on/off photocells as a standard feature, with automatic daylight harvesting/dimming
control as an available option. Additionally, nCM xx RJB family sensors are also available with
an optional auxiliary low voltage relay for simple integration with a BMS system or other building
nCM xx RJB
system. nCM PDT xx RJB
nCM xx RJB family sensors are powered via the nLight network bus and typically communicate
with one or more nLight enabled luminaires (e.g. Lithonia VTLED Series) or nLight relay/dimming
packs to enable control of fixtures individually or in groups. These configurations work standalone
and do not require a connection to a larger nLight network.
FEATURES
• 100% digital PIR detection
• Integrated photocell standard (disabled by default) — Photocell views down through sensor
lens and when enabled provides two selectable modes of operation
– On/Off mode: Photocell has full on/off control during periods of occupancy nCM
nCM 9 RJB
– Inhibit mode: Photocell can prevent lights from turning on if adequate daylight is available, nCM PDT 9 RJB
but cannot turn lights off
• Optional dimming photocell (ADCX option)
• Optional auxiliary low voltage relay (AR option) for dry contact output - relay only tracks
occupancy by default, ignoring switch and photocell commands
• LED status indicator
• Adjustable settings (e.g. occupancy time delays, photocell set-points) via push-button or
SensorView software application
• Broadcasts occupancy and photocell information over a local nLight channel nCM 10 RJB
• Remotely upgradeable firmware nCM PDT 10 RJB
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
nCM 6 RJB
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nCM xx RJB Example: nCM PDT 9 ADCX RJB
Series / Detection Coverage Type Options (See Below) RJ45 Port Location
nCM PIR Detection 9 Small Motion 360° RJB Rear RJ45 (CAT5e patch cable & RJ45
nCM PDT Dual Tech (PIR/ Microphonics) 10 Large Motion 360 ° splitter included)
6 High Mount 360° (not available with PDT version)
[blank] On/Off Photocell (disabled by default) [blank] None [blank] Single Time Delay [blank] Standard
ADCX Automatic Dimming Control (of remote dimming output) AR Low Voltage Aux. Relay 2P Dual Time Delay LT Low Temp / High Humidity
NOTES:
1. For information on models with side RJ45 ports, see website
2. Not available with AR or ADCX options
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 3
SPECIFICATIONS
Size: 4.55” Dia. (11.56 cm) 1.55” Deep (3.94 cm) nLight Bus Power Consumption: ~3mA
Weight: 6 oz nLight Network Connection: 2 RJ-45 Ports (via an included RJ-45
Mounting: Ceiling Tile / Sheetrock Surface, 3.5” Octagon splitter)
Box, Single Gang Handy box Relay Rating (AR option only): 1A @ 24 VAC/VDC (resistive only)
Color: Matte White ROHS Compliant, Title 24 Component
Wires / Cables: (1) CAT5e patch cable, 1ft (factory installed)
(2) 20 AWG wires (AR option only)
COVERAGE PATTERNS
SMALL MOTION 360º (Model # nCM 9/nCM PDT 91)
3.7 12
9.1 6 3 0m 3 6 9.1
30 20 10 0 ft 10 20 30
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 2 of 3
TYPICAL APPLICATIONS
nCM xx RJB
CAT-5e Splitter
(included)
nCM xx RJB
or
nCM xx ADCX RJB
nLight Enabled
Luminaire
TYPICAL APPLICATIONS
The following instructions are for mounting sensor directly to a ceiling tile or sheetrock
surface. Sensor’s mounting holes also align with standard round fixture or single gang
handy box (screws not provided).
1. Using template included with unit, mark spots on ceiling tile/sheetrock for cable hole
to/from nLight
and mounting anchors/screws
2. Drill 1/2” hole through ceiling surface at location indicated on template Zone
3. Insert provided anchors into ceiling surface at locations indicated on template CAT-5e CAT-5e
4. Remove provided RJ-45 splitter from sensor’s attached CAT5e cable and then thread
cable (and low voltage wires if -AR option included) through hole from underside
5. Mount sensor to anchors using two screws provided CAT-5e Splitter
CAT-5e
6. Attach provided RJ45 splitter device (model CAT5 Y) above ceiling to cable from sensor
(see diagram on right) BRN
7. Interconnect CAT-5e cables to/from rest of nLight zone to RJ45 splitter - AR option
BRN
8. Once power is received via CAT-5e connection, all devices in zone will automatically (contact closure
begin functioning together according to each device’s defaults
9. Install decorative sensor lid by rotating clockwise
10. Refer to included instruction card for default settings and directions on push-button
programming.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 3 of 3
OVERVIEW
The nCM xx RJB family of nLight ceiling/surface mount occupancy sensors provide a range of
networked sensor solutions for applications with finished ceilings (e.g. ceiling tiles, sheetrock,
plaster). nCM xx RJB family sensors utilize 100% digital Passive Infrared (PIR) detection and
are available with several lens options, providing flexibility for multiple mounting height and
coverage pattern requirements. Dual technology occupancy detection can also be added as an
option for applications where occupants are stationary for long periods of time. All sensors have
integrated on/off photocells as a standard feature, with automatic daylight harvesting/dimming
control as an available option. Additionally, nCM xx RJB family sensors are also available with
an optional auxiliary low voltage relay for simple integration with a BMS system or other building
nCM xx RJB
system. nCM PDT xx RJB
nCM xx RJB family sensors are powered via the nLight network bus and typically communicate
with one or more nLight enabled luminaires (e.g. Lithonia VTLED Series) or nLight relay/dimming
packs to enable control of fixtures individually or in groups. These configurations work standalone
and do not require a connection to a larger nLight network.
FEATURES
• 100% digital PIR detection
• Integrated photocell standard (disabled by default) — Photocell views down through sensor
lens and when enabled provides two selectable modes of operation
– On/Off mode: Photocell has full on/off control during periods of occupancy nCM
nCM 9 RJB
– Inhibit mode: Photocell can prevent lights from turning on if adequate daylight is available, nCM PDT 9 RJB
but cannot turn lights off
• Optional dimming photocell (ADCX option)
• Optional auxiliary low voltage relay (AR option) for dry contact output - relay only tracks
occupancy by default, ignoring switch and photocell commands
• LED status indicator
• Adjustable settings (e.g. occupancy time delays, photocell set-points) via push-button or
SensorView software application
• Broadcasts occupancy and photocell information over a local nLight channel nCM 10 RJB
• Remotely upgradeable firmware nCM PDT 10 RJB
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
nCM 6 RJB
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nCM xx RJB Example: nCM PDT 9 ADCX RJB
Series / Detection Coverage Type Options (See Below) RJ45 Port Location
nCM PIR Detection 9 Small Motion 360° RJB Rear RJ45 (CAT5e patch cable & RJ45
nCM PDT Dual Tech (PIR/ Microphonics) 10 Large Motion 360 ° splitter included)
6 High Mount 360° (not available with PDT version)
[blank] On/Off Photocell (disabled by default) [blank] None [blank] Single Time Delay [blank] Standard
ADCX Automatic Dimming Control (of remote dimming output) AR Low Voltage Aux. Relay 2P Dual Time Delay LT Low Temp / High Humidity
NOTES:
1. For information on models with side RJ45 ports, see website
2. Not available with AR or ADCX options
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 3
SPECIFICATIONS
Size: 4.55” Dia. (11.56 cm) 1.55” Deep (3.94 cm) nLight Bus Power Consumption: ~3mA
Weight: 6 oz nLight Network Connection: 2 RJ-45 Ports (via an included RJ-45
Mounting: Ceiling Tile / Sheetrock Surface, 3.5” Octagon splitter)
Box, Single Gang Handy box Relay Rating (AR option only): 1A @ 24 VAC/VDC (resistive only)
Color: Matte White ROHS Compliant, Title 24 Component
Wires / Cables: (1) CAT5e patch cable, 1ft (factory installed)
(2) 20 AWG wires (AR option only)
COVERAGE PATTERNS
SMALL MOTION 360º (Model # nCM 9/nCM PDT 91)
3.7 12
9.1 6 3 0m 3 6 9.1
30 20 10 0 ft 10 20 30
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 2 of 3
TYPICAL APPLICATIONS
nCM xx RJB
CAT-5e Splitter
(included)
nCM xx RJB
or
nCM xx ADCX RJB
nLight Enabled
Luminaire
TYPICAL APPLICATIONS
The following instructions are for mounting sensor directly to a ceiling tile or sheetrock
surface. Sensor’s mounting holes also align with standard round fixture or single gang
handy box (screws not provided).
1. Using template included with unit, mark spots on ceiling tile/sheetrock for cable hole
to/from nLight
and mounting anchors/screws
2. Drill 1/2” hole through ceiling surface at location indicated on template Zone
3. Insert provided anchors into ceiling surface at locations indicated on template CAT-5e CAT-5e
4. Remove provided RJ-45 splitter from sensor’s attached CAT5e cable and then thread
cable (and low voltage wires if -AR option included) through hole from underside
5. Mount sensor to anchors using two screws provided CAT-5e Splitter
CAT-5e
6. Attach provided RJ45 splitter device (model CAT5 Y) above ceiling to cable from sensor
(see diagram on right) BRN
7. Interconnect CAT-5e cables to/from rest of nLight zone to RJ45 splitter - AR option
BRN
8. Once power is received via CAT-5e connection, all devices in zone will automatically (contact closure
begin functioning together according to each device’s defaults
9. Install decorative sensor lid by rotating clockwise
10. Refer to included instruction card for default settings and directions on push-button
programming.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 3 of 3
OVERVIEW
nLight ECLYPSE extends the power of nLight to deliver the next level of lighting control. This BTL listed
B-BC device leverages native BACnet™/IP and WiFi to let you seamlessly integrate your lighting control
system with your building management systems. With its robust embedded web server, nLight ECLYPSE
hosts edge applications like SiteView™ Energy and Space Utilization, and generates actionable, visual data
with ENVYSION user interface.
FEATURES
nLight ECLYPSE
• BACnet Testing Laboratories (BTL) listed as a BACnet Building Controller (B-BC)
• Communicates over IP Local Area Network (LAN) with SensorView, Distech ECLYPSE, XPoint Wireless
IP & Building Management
• bridges and nADR devices Interface for nLight Networks
• View and manage the nLight network with nLight Explorer web interface which supports ECLYPSE
SiteView EnergyTM solution that allows monitoring of building energy consumption and provides an
informative dashboard demonstrating energy savings and environmental impact.
• Extra security provided by HTTPS Server
• %URZVHUꢀEDVHGꢁQ/LJKWꢁ(&/<36(ꢁDQGꢁ(19<6,21ꢁFRQƓJXUDWLRQꢁXVLQJꢁ+70/ꢂꢁWHFKQRORJ\
• Wi-Fi client, access point and hot spot capabilities
• Discovers and commissions nLight and Xpoint Wireless devices
• Provides system time-clock including astronomical time-clock capabilities.
• 6WRUHVꢁWLPHꢀEDVHGꢁDQGꢁLQSXWꢁDFWLYHꢁSURƓOHV
• Manages forwarding of global control channels across bridge devices and other nLight ECLYPSE
*DWHZD\Vꢃꢁ2QꢀGHPDQGꢁSURƓOHꢁIRUZDUGLQJꢁEHWZHHQꢁJDWHZD\V
• 5HPRWHO\ꢁFRQƓJXUDEOHꢁDQGꢁXSJUDGDEOH
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢁVXEMHFWꢁWRꢁFKDQJHꢁZLWKRXWꢁQRWLFHꢃ
ORDERING INFORMATION
NECY Example: NECY 120 BAC SVS
nECY nLight ECLYPSE 24 24 VAC/DC [blank] None [blank] Standard – Not Enabled [blank] Standard – Not Enabled
120 120-277 VAC BAC BACnet SVS SiteView1 SVEA SiteView Energy Application2
Notes
1. Requires BACnet option
2. Requires SVS & BACnet option
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NECY
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/06/17 1 of 3
SPECIFICATIONS
COMMUNICATION
Ethernet Connection Speed: 10/100 Mbps Supported BACnet MS/TP and Modbus RTU Connectivity:
Addressing: IPv4 or Hostname • BACnet MS/TP OR Modbus RTU 1 × RS-485 serial communications ports
ꢀ %$&QHWꢀ3URƓOHꢂꢀ ꢀ%$&QHWꢀ%XLOGLQJꢀ&RQWUROOHUꢀꢎ%ꢆ%&ꢏꢀ • Each RS-485 port supports one communication protocol at a time
BACnet Listing: BTL, B-BC • 56ꢆꢅꢐꢋꢀ:LULQJꢀꢆꢀꢊꢆSDLUꢀꢍꢀ&RPPRQꢃVKLHOG
BACnet Interconnectivity: BBMD forwarding capabilities • RS-485 EOL Resistor - Built-in
BACnet/IP to BACnet MS/TP routing • RS-485 Baud Rates - 9600, 19 200, 38 400, or 76 800 bps
BACnet Transport Layer: MS/TP & IP (optional) • 56ꢆꢅꢐꢋꢀ$GGUHVVLQJꢀꢆꢀ&RQWUROOHUōVꢀ:HEꢀ&RQƓJXUDWLRQꢀ,QWHUIDFH
Web Server Protocol: HTML5 Supported Wireless Connectivity:
Web Server Application Interface: REST API • Wireless Adapter - USB Port Connection
• Wi-Fi Communication Protocol - IEEE 802.11b/g/n
• Wi-Fi Network Types - Client, Access Point, Hotspot
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NECY
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/06/17 2 of 3
SYSTEM ARCHITECTURE
The nLight ECLYPSE serves as the backbone for nLight and XPoint Wireless networked luminaires and controls. The nLight ECLYPSE provides both nLight and XPoint Wireless
devices with schedule management and software programming interface. The backbone also provides support for system-wide controls such as master override switches,
automated demand response, and BACnet integration. One nLight ECLYPSE is capable of handling up to 1500 total devices and up to 128 channels for the entire network.
The nLight ECLYPSE is compatible with other Distech ECLYPSE products offering a full suite of BAS capabilities and also host Edge applications such as SiteView Energy.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NECY
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/06/17 3 of 3
OVERVIEW
The nLight ECLYPSE graphic touch screen (nGWY2 GFX) provides a simple and easy-to-use view into the
nLight network. This optional 3.5” high-resolution touch screen connects directly to the ECLYPSE nLight
interface port marked “GFX”, and provides system information and status.
FEATURES
• 3.5” Full color Touch Screen (Diagonal)
• Mounts to a Single Gang Switch Box
• 3URYLGHVꢀ2QOLQHꢀꢁꢀ2IŴLQHꢀꢁꢀ(UURUꢀ'HYLFHꢀ&RXQWVꢀ nGWY2 GFX
• Includes View of all Connected System Devices
• 3URYLGHVꢀ8VHUꢀ9LHZꢀDQGꢀ0DQXDOꢀ&RQWUROꢀRIꢀ$FWLYHꢁ,QDFWLYHꢀ3URƓOHVꢀ
• (QDEOHVꢀ8VHUꢀ&RQƓJXUDWLRQꢀRIꢀ'HYLFHꢀ/DEHOꢂꢀ;3:ꢀ0RGHꢂꢀ/RFDWLRQꢀDQGꢀ6HFXULW\ꢀ3DVVZRUGꢀ
• Optional Password Protection for Controls and Setup Screens
• Customizable Screen Saver Image
• 6XSSRUWHGꢀƓOHꢀIRUPDWVꢃꢀ-3*ꢂꢀ31*ꢂꢀ*,)ꢂꢀ%03ꢂꢀ7,)ꢀ
• Optimal resolution: 320x240 16bit color
• Onboard Help Screens
SPECIFICATIONS
Size: 5.06”H x 3.50”W x 0.69”D (12.85 cm x 8.89 cm x 1.75 cm)
Weight: 6 oz
Mounting: Single gang switch box or low voltage ring
Mounting Height: 60” (152 cm) - recommended
Color: White
ꢀ 1HWZRUNꢀFRQQHFWLRQꢃꢀ ꢄꢅꢆꢀ5-ꢇꢈꢀSRUWV
Input Voltage: 15-24VDC
Power Consumption: 60mA
Wires: None
Power Supply: PS-150 (347) via terminal connections – ordered separately
ROHS Compliant, Title 24 Component
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢉ
ORDERING INFORMATION
nGWY2 GFX Example: nGWY2 GFX
Series
nGWY2 GFX
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NGWY2 GFX
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 04/04/17 1 of 2
OVERVIEW
There are two RJ-45 ports on the rear of the graphic touchscreen for CAT5e N H
connection to the nLight ECLYPSE™. Only one port will be utilized, and the RED
RE WHT
PS 150 (347)
other will remain unused. Additionally, there is a set of power terminals where
BLK (120 V) / ORN (277 V)
low voltage power (e.g. from a PS 150 power supply module) is connected. BLK
BL
RED (347 V)
Note: No power is used/supplied from/to the nLight bus.
The Graphic WallPod flush mounts to a single-gang switch box. The housing
has two sliding panels that cover the mounting screws, an indicator LED, and a
recessed reset button.
RESET BUTTON
MICRO-USB
NLIGHT NETWORK
PORT
PORTS (RJ-45) POWER STATUS LED
SCREW HOLES
POWER TERMINALS
• Before mounting, connect Class 2 low voltage wires from power supply to power terminal connections (polarity insensitive)
• Verify unit has power by observing screen and/or LED
• &RQQHFWꢀ&$7ꢁꢂHꢀFDEOHꢃVꢄꢀIURPꢀQ/,JKWꢀ(&/<36(ꢀSRUWꢀPDUNHGꢀŏ*);ŐꢀWRꢀ5-ꢁꢅꢂꢀSRUW
• Unit will begin discovering connected devices (indicated by on-screen message box)
• Mount unit to standard single gang switch box (screws provided)
• 7RꢀDFFHVVꢀFRQƓJXUDWLRQꢀVFUHHQVꢆꢀWRXFKꢀORFNꢀLFRQꢀLQꢀXSSHUꢀOHIWꢇꢀ'HIDXOWꢀSDVVZRUGꢀLVꢀŏꢈꢉꢊꢅŐ
• Pressing reset button twice is equivalent to repowering unit
• Press reset button three times to restart unit in screen-calibration mode
Riser
nECY nLight Zone
SensorView Schedules and System
Configuration and Monitoring Software Profiles
nBRG
nLight Zones
nLight Bus
nGWY2 GFX
PS 150 N H
BLK - 120 V
WHT
RED ORN - 277 V
BLK BLK/ORN
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NGWY2 GFX
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 04/04/17 2 of 2
OVERVIEW
The nLight Handheld Programmer uses a Bluetooth® Low Energy (BLE) Radio Module to
allow wireless communication between the local nLight zone and iOS/Android smart phone
DSSOLFDWLRQꢀꢁQ&RQƓJꢂꢁ7KLVꢁGHYLFHꢁRIIHUVꢁWZRꢁ5-ꢃꢄꢅꢁSRUWVꢁWRꢁEHꢁSODFHGꢁLQꢁDQ\ꢁORFDWLRQꢁRQꢁDꢁORFDOꢁ
nLight zone, and the unit powers up directly off of the nLight bus. The smart phone application
offers secure pairing with the BLE device when within range, and once connected can be used for
LGHQWLI\LQJꢁDQGꢁFRQƓJXULQJꢁGHYLFHVꢁZLWKLQꢁWKDWꢁ]RQHꢂ
nIO BT
SPECIFICATIONS Bluetooth® Low Energy
Communication Module
Size (Inline Wired):
2.54”H x 1.98”W x 1.00”D (6.45 cm x 5.03 cm x 2.54cm)
Weight:
2oz
Color:
Clear (blue LED)
ꢁ Q/LJKWꢁ1HWZRUNꢁ3RUWVꢆꢁ
ꢇꢁ5-ꢃꢄꢅ
Bus Power Consumption: ~7 mA
Wires:
None
Wireless Frequency:BLE
Wireless Range Guidelines:(See installation notes for maximum signal)
Line of Sight: ~50 ft
Plasterboard/Dry Wood: ~30 ft
Concrete: ~15 ft
RoHS Compliant, Title 24 System Component
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢁVXEMHFWꢁWRꢁFKDQJHꢁZLWKRXWꢁQRWLFHꢂ
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
nLight and the Acuity Controls and Acuity Brands logos are trademarks of Acuity Brands. Bluetooth is
a trademark of Bluetooth SIG, Inc. used by Acuity Brands under license. Apple and the Apple logo are
trademarks of Apple Inc. Android and Google Play are trademarks of Google, Inc. Other trademarks are
property of their respective owners.
ORDERING INFORMATION
nIO BT Example: nIO BT
Series
nIO BT Bluetooth Low Energy Communication Module
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NIO BT
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/28/17 1 of 2
WIRING
Stand-Alone nLight Zone
COMPLIANCE INFORMATION
nIO BT: FCC: VR8-SSIINTR004
IC: 7791A-SSIINTR004
These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
The intentional radiator is identical in all variants of the apparatus.
&$87,21ꢀꢁ&KDQJHVꢁRUꢁPRGLƓFDWLRQVꢁQRWꢁH[SUHVVO\ꢁDSSURYHGꢁE\ꢁWKHꢁSDUW\ꢁUHVSRQVLEOHꢁIRUꢁFRPSOLDQFHꢁFRXOGꢁYRLGꢁWKHꢁXVHUōVꢁDXWKRULW\ꢁWRꢁRSHUDWHꢁWKHꢁHTXLSPHQWꢂ
CAN RSS-Gen/CNR-Gen:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of the device.
/HꢁSU«VHQWꢁDSSDUHLOꢁHVWꢁFRQIRUPHꢁDX[ꢁ&15ꢁGō,QGXVWULHꢁ&DQDGDꢁDSSOLFDEOHVꢁDX[ꢁDSSDUHLOVꢁUDGLRꢁH[HPSWVꢁGHꢁOLFHQFHꢂꢁ/ōH[SORLWDWLRQꢁHVWꢁDXWRULV«HꢁDX[ꢁGHX[ꢁFRQGLWLRQVꢁVXLYDQWHVꢁꢀꢁ
ꢃꢄꢅꢁOōDSSDUHLOꢁQHꢁGRLWꢁSDVꢁSURGXLUHꢁGHꢁEURXLOODJHꢆꢁHWꢁꢃꢇꢅꢁOōXWLOLVDWHXUꢁGHꢁOōDSSDUHLOꢁGRLWꢁDFFHSWHUꢁWRXWꢁEURXLOODJHꢁUDGLR«OHFWULTXHꢁVXELꢆꢁP¬PHꢁVLꢁOHꢁEURXLOODJHꢁHVWꢁVXVFHSWLEOHꢁGōHQꢁ
compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
&RQIRUP«PHQWꢁ¢ꢁODꢁU«JOHPHQWDWLRQꢁGō,QGXVWULHꢁ&DQDGDꢆꢁOHꢁSU«VHQWꢁ«PHWWHXUꢁUDGLRꢁSHXWꢁIRQFWLRQQHUꢁDYHFꢁXQHꢁDQWHQQHꢁGōXQꢁW\SHꢁHWꢁGōXQꢁJDLQꢁPD[LPDOꢁꢃRXꢁLQI«ULHXUꢁDSSURXY«ꢁSRXUꢁ
Oō«PHWWHXUꢁSDUꢁ,QGXVWULHꢁ&DQDGDꢂ
'DQVꢁOHꢁEXWꢁGHꢁU«GXLUHꢁOHVꢁULVTXHVꢁGHꢁEURXLOODJHꢁUDGLR«OHFWULTXHꢁ¢ꢁOōLQWHQWLRQꢁGHVꢁDXWUHVꢁXWLOLVDWHXUVꢆꢁLOꢁIDXWꢁFKRLVLUꢁOHꢁW\SHꢁGōDQWHQQHꢁHWꢁVRQꢁJDLQꢁGHꢁVRUWHꢁTXHꢁODSXLVVDQFHꢁLVRWURSHꢁ
UD\RQQ«Hꢁ«TXLYDOHQWHꢁꢃSꢂLꢂUꢂHꢂꢅꢁQHꢁG«SDVVHꢁSDVꢁOōLQWHQVLW«ꢁQ«FHVVDLUHꢁ¢ꢁOō«WDEOLVVHPHQWꢁGōXQHꢁFRPPXQLFDWLRQꢁVDWLVIDLVDQWHꢂ
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NIO BT
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/28/17 2 of 2
OVERVIEW
The nLight nIO PC KIT provides an outdoor photocontrol solution for nLight networks. In
addition to a weatherproof outdoor photocontrol that mounts to any 1/2” knockout, the nIO
PC KIT includes an interface device with a normally low input. This device called a nIO NLI 1S,
detects the state of the photocontrol and communicates it over the nLight network to a relay(s)
controlling a lighting load. The nIO NLI 1S can also trigger local or remote control scenes to run
when the photocontrol’s state changes.
The nIO NLI 1S is daisy-chain wired into any zone of nLight devices (sensors, power packs,
WallPods) using CAT-5e cabling. Power to the nIO NLI 1S device is provided by the CAT-5e nIO PC Kit
connection to an nLight power pack/supply within its zone, or a Bridge. Power to the outdoor Outdoor Photocell
photocontrol is provided via Class 2 wires from the included PS 150 power supply or other low Interface Kit
voltage source (for example the auxiliary power output on an nPANEL 4).
The nIO NLI 1S can trigger one of several modes when the connected outdoor photocontrol
changes states:
FEATURES
• Kit Provides both Outdoor Photocell & Specialized nIO Interface Device
• nIO Interfaces Outdoor Photocell Using Normally Low Input
• Sends Toggle Signal to Relays within Local Zone
• Initiates a Local or Remote Scene
• Communicates w/ nLight Network *Outdoor Photocell (PC) is model
• Remotely Configurable/Upgradeable number LCS-624D from Precision
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nIO PC Kit Example: nIO PC Kit
Series
nIO PC Kit
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 2
WIRING
OPTION 1* OPTION 2*
*Note, line connection to power supply not shown. Additional nLight devices are
required to switch lighting load (e.g., nPP16). *Note, line and load connections to nPANEL 4 not shown.
GRY GRY
RED BLK - + RED BLK - +
Outdoor Outdoor nIO NLI 1S
Photocontrol PS 150 Photocontrol nPANEL 4
nIO NLI 1S Power Unit
Unit
Supply
SPECIFICATIONS
(nIO NLI 1S)
Size: 3.38”H x 2.53”W x 1.83”D (8.59 cm x 6.43 cm x 4.65 cm)
Weight: 2 oz
Color: White
Network Connection: 2 RJ-45 each device
Power Requirements: < 3 mA
Wires: 20 AWG (3)
RoHS Compliant
(PC)
Size: 3.50” H x 1.25” W x 0.25” D (8.89 cm x 3.18 cm x 0.64 cm)
Mounting: 1/2” KO in any approved weatherproof outdoor box
Weight: 4 oz
Color: Gray
PowerRequirements: < 35 mA @ 12-28 VDC
Wires: 20 AWG (3)
(PS150)
Size: (not including ½” chase nipple) 3.00” H x 2.25” W x 1.88” D
(7.62 cm x 5.72 cm x 4.78 cm)
Weight: 6 oz
Mounting: 1/2” KO
Color: Black
Operating Voltage: 120/277
Output Voltage, Current: 15 VDC, 150 mA
Wires: 18 AWG (3) & 20 AWG (2)
RoHS Compliant
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 2 of 2
OVERVIEW
The nPODM Series WallPods are nLight-enabled toggle and/or raise/lower switches that provide a user with
local control of a lighting zone. These single gang decorator style devices have soft-click buttons and have
a green LED indicator for each button. WallPods communicate with other nLight devices via a CAT-5e cable
that connects to one of its two RJ-45 connectors. A basic low voltage WallPod can work with an nLight power
SDFNꢀRUꢀQ/LJKWꢀHQDEOHGꢀƓ[WXUHꢀWRꢀSURYLGHꢀWRJJOHꢀVZLWFKꢀRSHUDWLRQꢁꢀ:DOO3RGVꢀZLWKꢀWKHꢀ';ꢀRSWLRQꢀKDYHꢀWKHꢀ
added ability to adjust the level of any nLight controlled dimmable lighting.
FEATURES nPODM
• Communicates with nLight network
Wallpod: On/Off & On/
• 5HPRWHO\ꢀFRQƓJXUDEOHꢂXSJUDGHDEOH Off+Raise/Lower
• Soft-click push-button control
• Custom button engraving at no charge (WH, IV, AL GY units only)
• 1, 2, or 4 channel on/off
• 1, 2, or 4 channel raise/lower
• ŏ'\QDPLFŐꢀRSWLRQVꢀIRUꢀFXVWRPꢀEXWWRQꢀQDPHVꢀZKHQꢀSDLULQJꢀZLWKꢀ$FXLW\ꢀ%UDQGVꢀQ781(ꢀƓ[WXUHV
Warranty
Five-year limited warranty. Complete warranty terms located at:
ZZZꢁDFXLW\EUDQGVꢁFRPꢂ&XVWRPHU5HVRXUFHVꢂ7HUPVBDQGBFRQGLWLRQVꢁDVS[
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢁ
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nPODM Example: nPODM 2P WH
XX-Specify
Series Preset Type Dimming Control Dynamic Color Temp/ Humidity
nPODM [blank] Single channel [blank] On/off control [blank] Standard WH White [blank] Normal
2P Two channels DX On/off + raise/lower control CCT1 Correlated color temperature IV Ivory LT Low temp
4P Four channels GRSC1 Grayscale GY Gray
COLOR1 Color control AL Almond
BK Black
RD Red
• &XVWRPꢀOHWWHULQJꢀIRUꢀ:+ꢃꢀ,9ꢃꢀ$/ꢃꢀDQGꢀ*<ꢀXQLWVꢀFDQꢀEHꢀVSHFLƓHGꢀDQGꢀRUGHUHGꢀDWꢀQRꢀFKDUJHꢀDWꢄꢀ
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
• 7RꢀHQVXUHꢀFRORUꢀXQLIRUPLW\ꢃꢀRUGHULQJꢀWHPSODWHVꢀIDFLOLWDWHꢀVSHFLƓ\LQJꢀDOOꢀEXWWRQVꢀRQꢀDꢀXQLWꢀDVꢀFXVWRPꢀ
lettered. Replacing single buttons not recommended.
• %XWWRQVꢀPD\ꢀVKLSꢀVHSDUDWHO\ꢀDQGꢀUHTXLUHꢀƓHOGꢀLQVWDOODWLRQꢁꢀ
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 1 of 3
SPECIFICATIONS
6L]Hꢀꢁ ꢂQRWꢁLQFOXGLQJꢁJURXQGꢁVWUDSꢃꢁꢄꢅꢆꢇŐꢁ+ꢁ[ꢁꢈꢅꢉꢊŐꢁ:ꢁ[ꢁꢈꢅꢉꢋŐꢁ'ꢁ
ꢂꢉꢅꢌꢉꢁFPꢁ[ꢁꢇꢅꢄꢆꢁFPꢁ[ꢁꢇꢅꢈꢇꢁFPꢃꢁ
Weight: 2 oz
0RXQWLQJꢀꢁ 6LQJOHꢁ*DQJꢁ6ZLWFKꢁ%R[ꢁRUꢁ/RZꢁ9ROWDJHꢁ5LQJ
Color: White, Ivory, Lt. Almond, Gray, Black, Red
nLight Network Ports: 2 RJ-45
Power Consumption: < 5 mA
Wires: None
RoHS Compliant, Title 24 System Component
WIRING
TYPICAL WIRING
Power to WallPod device is provided via the CAT-5e connection to an nLight enabled fixture, nLight power pack (e.g. nPP16), power supply (nPS80), or Bridge (nBRG 8).
BLK - 120 V
nPP16 ORN - 277 V
CAT-5 CAT-5
LOAD
CAT-5
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 2 of 3
DEFAULT LABELING
ON OFF 1 2
ON OFF 3 4
ON OFF ON
ON OFF OFF
Dynamic wallpod options feature custom button names when pairing with Acuity Brands nTUNE(TM) fixtures. Reference fixture cut sheets for additional details.
Custom lettering for WH, IV, AL, and GY units can be specified and ordered at no charge at:
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
INSTALLATION
• 0RXQWꢀ:DOO3RGꢀXVLQJꢀKROHVꢀWKDWꢀDOLJQꢀZLWKꢀVWDQGDUGꢀVLQJOHꢀJDQJꢀVZLWFKꢀER[ꢀRUꢀORZꢀYROWDJHꢀULQJ
• Access RJ-45 ports by sliding plastic guard up
SLIDE
• Once power is received via CAT-5e connection, all devices in zone will automatically begin
T-
5
PROGRAMMING
Refer to instruction card IN-11.3 for directions on programming the sensor via the upper-most left push-button. All buttons are factory set to the matching switch channel (button
1 - channel 1, button 2 - channel 2, etc). For nPODM 4P DX, channels to be controlled are selected first, then the control button (on/off or raise/lower).
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 3 of 3
OVERVIEW
The nPODM Series WallPods are nLight-enabled toggle and/or raise/lower switches that provide a user with
local control of a lighting zone. These single gang decorator style devices have soft-click buttons and have
a green LED indicator for each button. WallPods communicate with other nLight devices via a CAT-5e cable
that connects to one of its two RJ-45 connectors. A basic low voltage WallPod can work with an nLight power
SDFNꢀRUꢀQ/LJKWꢀHQDEOHGꢀƓ[WXUHꢀWRꢀSURYLGHꢀWRJJOHꢀVZLWFKꢀRSHUDWLRQꢁꢀ:DOO3RGVꢀZLWKꢀWKHꢀ';ꢀRSWLRQꢀKDYHꢀWKHꢀ
added ability to adjust the level of any nLight controlled dimmable lighting.
FEATURES nPODM
• Communicates with nLight network
Wallpod: On/Off & On/
• 5HPRWHO\ꢀFRQƓJXUDEOHꢂXSJUDGHDEOH Off+Raise/Lower
• Soft-click push-button control
• Custom button engraving at no charge (WH, IV, AL GY units only)
• 1, 2, or 4 channel on/off
• 1, 2, or 4 channel raise/lower
• ŏ'\QDPLFŐꢀRSWLRQVꢀIRUꢀFXVWRPꢀEXWWRQꢀQDPHVꢀZKHQꢀSDLULQJꢀZLWKꢀ$FXLW\ꢀ%UDQGVꢀQ781(ꢀƓ[WXUHV
Warranty
Five-year limited warranty. Complete warranty terms located at:
ZZZꢁDFXLW\EUDQGVꢁFRPꢂ&XVWRPHU5HVRXUFHVꢂ7HUPVBDQGBFRQGLWLRQVꢁDVS[
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢁ
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nPODM Example: nPODM 2P WH
XX-Specify
Series Preset Type Dimming Control Dynamic Color Temp/ Humidity
nPODM [blank] Single channel [blank] On/off control [blank] Standard WH White [blank] Normal
2P Two channels DX On/off + raise/lower control CCT1 Correlated color temperature IV Ivory LT Low temp
4P Four channels GRSC1 Grayscale GY Gray
COLOR1 Color control AL Almond
BK Black
RD Red
• &XVWRPꢀOHWWHULQJꢀIRUꢀ:+ꢃꢀ,9ꢃꢀ$/ꢃꢀDQGꢀ*<ꢀXQLWVꢀFDQꢀEHꢀVSHFLƓHGꢀDQGꢀRUGHUHGꢀDWꢀQRꢀFKDUJHꢀDWꢄꢀ
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
• 7RꢀHQVXUHꢀFRORUꢀXQLIRUPLW\ꢃꢀRUGHULQJꢀWHPSODWHVꢀIDFLOLWDWHꢀVSHFLƓ\LQJꢀDOOꢀEXWWRQVꢀRQꢀDꢀXQLWꢀDVꢀFXVWRPꢀ
lettered. Replacing single buttons not recommended.
• %XWWRQVꢀPD\ꢀVKLSꢀVHSDUDWHO\ꢀDQGꢀUHTXLUHꢀƓHOGꢀLQVWDOODWLRQꢁꢀ
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 1 of 3
SPECIFICATIONS
6L]Hꢀꢁ ꢂQRWꢁLQFOXGLQJꢁJURXQGꢁVWUDSꢃꢁꢄꢅꢆꢇŐꢁ+ꢁ[ꢁꢈꢅꢉꢊŐꢁ:ꢁ[ꢁꢈꢅꢉꢋŐꢁ'ꢁ
ꢂꢉꢅꢌꢉꢁFPꢁ[ꢁꢇꢅꢄꢆꢁFPꢁ[ꢁꢇꢅꢈꢇꢁFPꢃꢁ
Weight: 2 oz
0RXQWLQJꢀꢁ 6LQJOHꢁ*DQJꢁ6ZLWFKꢁ%R[ꢁRUꢁ/RZꢁ9ROWDJHꢁ5LQJ
Color: White, Ivory, Lt. Almond, Gray, Black, Red
nLight Network Ports: 2 RJ-45
Power Consumption: < 5 mA
Wires: None
RoHS Compliant, Title 24 System Component
WIRING
TYPICAL WIRING
Power to WallPod device is provided via the CAT-5e connection to an nLight enabled fixture, nLight power pack (e.g. nPP16), power supply (nPS80), or Bridge (nBRG 8).
BLK - 120 V
nPP16 ORN - 277 V
CAT-5 CAT-5
LOAD
CAT-5
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 2 of 3
DEFAULT LABELING
ON OFF 1 2
ON OFF 3 4
ON OFF ON
ON OFF OFF
Dynamic wallpod options feature custom button names when pairing with Acuity Brands nTUNE(TM) fixtures. Reference fixture cut sheets for additional details.
Custom lettering for WH, IV, AL, and GY units can be specified and ordered at no charge at:
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
INSTALLATION
• 0RXQWꢀ:DOO3RGꢀXVLQJꢀKROHVꢀWKDWꢀDOLJQꢀZLWKꢀVWDQGDUGꢀVLQJOHꢀJDQJꢀVZLWFKꢀER[ꢀRUꢀORZꢀYROWDJHꢀULQJ
• Access RJ-45 ports by sliding plastic guard up
SLIDE
• Once power is received via CAT-5e connection, all devices in zone will automatically begin
T-
5
PROGRAMMING
Refer to instruction card IN-11.3 for directions on programming the sensor via the upper-most left push-button. All buttons are factory set to the matching switch channel (button
1 - channel 1, button 2 - channel 2, etc). For nPODM 4P DX, channels to be controlled are selected first, then the control button (on/off or raise/lower).
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 3 of 3
OVERVIEW
The nPODM Series WallPods are nLight-enabled toggle and/or raise/lower switches that provide a user with
local control of a lighting zone. These single gang decorator style devices have soft-click buttons and have
a green LED indicator for each button. WallPods communicate with other nLight devices via a CAT-5e cable
that connects to one of its two RJ-45 connectors. A basic low voltage WallPod can work with an nLight power
SDFNꢀRUꢀQ/LJKWꢀHQDEOHGꢀƓ[WXUHꢀWRꢀSURYLGHꢀWRJJOHꢀVZLWFKꢀRSHUDWLRQꢁꢀ:DOO3RGVꢀZLWKꢀWKHꢀ';ꢀRSWLRQꢀKDYHꢀWKHꢀ
added ability to adjust the level of any nLight controlled dimmable lighting.
FEATURES nPODM
• Communicates with nLight network
Wallpod: On/Off & On/
• 5HPRWHO\ꢀFRQƓJXUDEOHꢂXSJUDGHDEOH Off+Raise/Lower
• Soft-click push-button control
• Custom button engraving at no charge (WH, IV, AL GY units only)
• 1, 2, or 4 channel on/off
• 1, 2, or 4 channel raise/lower
• ŏ'\QDPLFŐꢀRSWLRQVꢀIRUꢀFXVWRPꢀEXWWRQꢀQDPHVꢀZKHQꢀSDLULQJꢀZLWKꢀ$FXLW\ꢀ%UDQGVꢀQ781(ꢀƓ[WXUHV
Warranty
Five-year limited warranty. Complete warranty terms located at:
ZZZꢁDFXLW\EUDQGVꢁFRPꢂ&XVWRPHU5HVRXUFHVꢂ7HUPVBDQGBFRQGLWLRQVꢁDVS[
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢁ
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nPODM Example: nPODM 2P WH
XX-Specify
Series Preset Type Dimming Control Dynamic Color Temp/ Humidity
nPODM [blank] Single channel [blank] On/off control [blank] Standard WH White [blank] Normal
2P Two channels DX On/off + raise/lower control CCT1 Correlated color temperature IV Ivory LT Low temp
4P Four channels GRSC1 Grayscale GY Gray
COLOR1 Color control AL Almond
BK Black
RD Red
• &XVWRPꢀOHWWHULQJꢀIRUꢀ:+ꢃꢀ,9ꢃꢀ$/ꢃꢀDQGꢀ*<ꢀXQLWVꢀFDQꢀEHꢀVSHFLƓHGꢀDQGꢀRUGHUHGꢀDWꢀQRꢀFKDUJHꢀDWꢄꢀ
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
• 7RꢀHQVXUHꢀFRORUꢀXQLIRUPLW\ꢃꢀRUGHULQJꢀWHPSODWHVꢀIDFLOLWDWHꢀVSHFLƓ\LQJꢀDOOꢀEXWWRQVꢀRQꢀDꢀXQLWꢀDVꢀFXVWRPꢀ
lettered. Replacing single buttons not recommended.
• %XWWRQVꢀPD\ꢀVKLSꢀVHSDUDWHO\ꢀDQGꢀUHTXLUHꢀƓHOGꢀLQVWDOODWLRQꢁꢀ
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 1 of 3
SPECIFICATIONS
6L]Hꢀꢁ ꢂQRWꢁLQFOXGLQJꢁJURXQGꢁVWUDSꢃꢁꢄꢅꢆꢇŐꢁ+ꢁ[ꢁꢈꢅꢉꢊŐꢁ:ꢁ[ꢁꢈꢅꢉꢋŐꢁ'ꢁ
ꢂꢉꢅꢌꢉꢁFPꢁ[ꢁꢇꢅꢄꢆꢁFPꢁ[ꢁꢇꢅꢈꢇꢁFPꢃꢁ
Weight: 2 oz
0RXQWLQJꢀꢁ 6LQJOHꢁ*DQJꢁ6ZLWFKꢁ%R[ꢁRUꢁ/RZꢁ9ROWDJHꢁ5LQJ
Color: White, Ivory, Lt. Almond, Gray, Black, Red
nLight Network Ports: 2 RJ-45
Power Consumption: < 5 mA
Wires: None
RoHS Compliant, Title 24 System Component
WIRING
TYPICAL WIRING
Power to WallPod device is provided via the CAT-5e connection to an nLight enabled fixture, nLight power pack (e.g. nPP16), power supply (nPS80), or Bridge (nBRG 8).
BLK - 120 V
nPP16 ORN - 277 V
CAT-5 CAT-5
LOAD
CAT-5
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 2 of 3
DEFAULT LABELING
ON OFF 1 2
ON OFF 3 4
ON OFF ON
ON OFF OFF
Dynamic wallpod options feature custom button names when pairing with Acuity Brands nTUNE(TM) fixtures. Reference fixture cut sheets for additional details.
Custom lettering for WH, IV, AL, and GY units can be specified and ordered at no charge at:
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
INSTALLATION
• 0RXQWꢀ:DOO3RGꢀXVLQJꢀKROHVꢀWKDWꢀDOLJQꢀZLWKꢀVWDQGDUGꢀVLQJOHꢀJDQJꢀVZLWFKꢀER[ꢀRUꢀORZꢀYROWDJHꢀULQJ
• Access RJ-45 ports by sliding plastic guard up
SLIDE
• Once power is received via CAT-5e connection, all devices in zone will automatically begin
T-
5
PROGRAMMING
Refer to instruction card IN-11.3 for directions on programming the sensor via the upper-most left push-button. All buttons are factory set to the matching switch channel (button
1 - channel 1, button 2 - channel 2, etc). For nPODM 4P DX, channels to be controlled are selected first, then the control button (on/off or raise/lower).
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 3 of 3
OVERVIEW
The nPODM Series WallPods are nLight-enabled toggle and/or raise/lower switches that provide a user with
local control of a lighting zone. These single gang decorator style devices have soft-click buttons and have
a green LED indicator for each button. WallPods communicate with other nLight devices via a CAT-5e cable
that connects to one of its two RJ-45 connectors. A basic low voltage WallPod can work with an nLight power
SDFNꢀRUꢀQ/LJKWꢀHQDEOHGꢀƓ[WXUHꢀWRꢀSURYLGHꢀWRJJOHꢀVZLWFKꢀRSHUDWLRQꢁꢀ:DOO3RGVꢀZLWKꢀWKHꢀ';ꢀRSWLRQꢀKDYHꢀWKHꢀ
added ability to adjust the level of any nLight controlled dimmable lighting.
FEATURES nPODM
• Communicates with nLight network
Wallpod: On/Off & On/
• 5HPRWHO\ꢀFRQƓJXUDEOHꢂXSJUDGHDEOH Off+Raise/Lower
• Soft-click push-button control
• Custom button engraving at no charge (WH, IV, AL GY units only)
• 1, 2, or 4 channel on/off
• 1, 2, or 4 channel raise/lower
• ŏ'\QDPLFŐꢀRSWLRQVꢀIRUꢀFXVWRPꢀEXWWRQꢀQDPHVꢀZKHQꢀSDLULQJꢀZLWKꢀ$FXLW\ꢀ%UDQGVꢀQ781(ꢀƓ[WXUHV
Warranty
Five-year limited warranty. Complete warranty terms located at:
ZZZꢁDFXLW\EUDQGVꢁFRPꢂ&XVWRPHU5HVRXUFHVꢂ7HUPVBDQGBFRQGLWLRQVꢁDVS[
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢁ
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nPODM Example: nPODM 2P WH
XX-Specify
Series Preset Type Dimming Control Dynamic Color Temp/ Humidity
nPODM [blank] Single channel [blank] On/off control [blank] Standard WH White [blank] Normal
2P Two channels DX On/off + raise/lower control CCT1 Correlated color temperature IV Ivory LT Low temp
4P Four channels GRSC1 Grayscale GY Gray
COLOR1 Color control AL Almond
BK Black
RD Red
• &XVWRPꢀOHWWHULQJꢀIRUꢀ:+ꢃꢀ,9ꢃꢀ$/ꢃꢀDQGꢀ*<ꢀXQLWVꢀFDQꢀEHꢀVSHFLƓHGꢀDQGꢀRUGHUHGꢀDWꢀQRꢀFKDUJHꢀDWꢄꢀ
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
• 7RꢀHQVXUHꢀFRORUꢀXQLIRUPLW\ꢃꢀRUGHULQJꢀWHPSODWHVꢀIDFLOLWDWHꢀVSHFLƓ\LQJꢀDOOꢀEXWWRQVꢀRQꢀDꢀXQLWꢀDVꢀFXVWRPꢀ
lettered. Replacing single buttons not recommended.
• %XWWRQVꢀPD\ꢀVKLSꢀVHSDUDWHO\ꢀDQGꢀUHTXLUHꢀƓHOGꢀLQVWDOODWLRQꢁꢀ
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 1 of 3
SPECIFICATIONS
6L]Hꢀꢁ ꢂQRWꢁLQFOXGLQJꢁJURXQGꢁVWUDSꢃꢁꢄꢅꢆꢇŐꢁ+ꢁ[ꢁꢈꢅꢉꢊŐꢁ:ꢁ[ꢁꢈꢅꢉꢋŐꢁ'ꢁ
ꢂꢉꢅꢌꢉꢁFPꢁ[ꢁꢇꢅꢄꢆꢁFPꢁ[ꢁꢇꢅꢈꢇꢁFPꢃꢁ
Weight: 2 oz
0RXQWLQJꢀꢁ 6LQJOHꢁ*DQJꢁ6ZLWFKꢁ%R[ꢁRUꢁ/RZꢁ9ROWDJHꢁ5LQJ
Color: White, Ivory, Lt. Almond, Gray, Black, Red
nLight Network Ports: 2 RJ-45
Power Consumption: < 5 mA
Wires: None
RoHS Compliant, Title 24 System Component
WIRING
TYPICAL WIRING
Power to WallPod device is provided via the CAT-5e connection to an nLight enabled fixture, nLight power pack (e.g. nPP16), power supply (nPS80), or Bridge (nBRG 8).
BLK - 120 V
nPP16 ORN - 277 V
CAT-5 CAT-5
LOAD
CAT-5
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 2 of 3
DEFAULT LABELING
ON OFF 1 2
ON OFF 3 4
ON OFF ON
ON OFF OFF
Dynamic wallpod options feature custom button names when pairing with Acuity Brands nTUNE(TM) fixtures. Reference fixture cut sheets for additional details.
Custom lettering for WH, IV, AL, and GY units can be specified and ordered at no charge at:
http://www.acuitybrands.com/products/-/media/Files/Acuity/Brands/Controls/nLight/NGRAVE.PDF
INSTALLATION
• 0RXQWꢀ:DOO3RGꢀXVLQJꢀKROHVꢀWKDWꢀDOLJQꢀZLWKꢀVWDQGDUGꢀVLQJOHꢀJDQJꢀVZLWFKꢀER[ꢀRUꢀORZꢀYROWDJHꢀULQJ
• Access RJ-45 ports by sliding plastic guard up
SLIDE
• Once power is received via CAT-5e connection, all devices in zone will automatically begin
T-
5
PROGRAMMING
Refer to instruction card IN-11.3 for directions on programming the sensor via the upper-most left push-button. All buttons are factory set to the matching switch channel (button
1 - channel 1, button 2 - channel 2, etc). For nPODM 4P DX, channels to be controlled are selected first, then the control button (on/off or raise/lower).
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com nPODM
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/13/17 3 of 3
OVERVIEW
The nLight nPP16 family of power packs is the workhorse of an nLight system, delivering robust system
performance and design versatility for commercial and industrial lighting control applications. The nPP16
family is capable of switching loads up to 16 Amps via an internal latching relay designed with robust
SURWHFWLRQꢀIURPꢀWKHꢀKDUVKꢀVZLWFKLQJꢀUHTXLUHPHQWVꢀRIꢀ7ꢁꢀŴXRUHVFHQWꢀDQGꢀ/('ꢀORDGVꢂꢀ7KHVHꢀSRZHUꢀSDFNVꢀDOVRꢀ
provide nLight system bus power - up to 40mA from each of its two RJ-45 ports - by transforming Class 1
line voltage (120/277 VAC or 347 VAC) to Class 2 low voltage (15 VDC). This power is typically utilized by
other nLight devices within the power pack’s local control zone; however, remaining power is also made
available over the network for Bridges and devices in other zones to utilize.
FEATURES nPP16
•
•
Communicates w/ nLight Network
Self-Contained Relay Switches Line Voltage Load
Power/Relay Pack
• Supplies 40mA of Bus Power / RJ-45 port
• Optional out-of-box vacancy and partial-on modes
• 5HPRWHO\ꢀ&RQƓJXUDEOHꢃ8SJUDGHDEOH
• Push-Button Programmable
• &RQƓJXUDEOHꢀ5HOD\ꢀ/RJLF
• Extended Chase Nipple
• Plenum rated
SPECIFICATIONS
Size: (not including ½” chase nipple) 3.38” H x 2.53” W x 1.83” D (8.59 cm
x 6.43 cm x 4.65 cm) Model #: nPP16 (D) Model #: nPP16 (D) ER
Weight: 6 oz
Mounting: 1/2” Knockout
Color: White (standard), Red (ER)
nLight Network Ports: 2 RJ-45
Operating Voltage: 120/240/277VAC, 347VAC (with 347 option)
Max Load: 16A @ 120VAC/277VAC, 347VAC
Motor Load: 1/2 HP
Relay type: Latching
Frequency: 50/60Hz
Operating Temp: 14°F to 122°F (-10°C to 50°C)
Relative Humidity: 20-90% non-condensing
Bus Output Current/Voltage: 15 VDC, 40 mA / port (non-ER units only), 40 mA total at 240VAC
Max Dimming Load: Sinks 100mA; 0-10VDC dimmable ballasts or LED drivers
*If power pack is enclosed within a junction box, max ambient temperature is 45° C
RoHS Compliant, Title 24 System Component, Class 1 Listed, Plenum Rated, cULus Listed, CSA Listed
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢂ
ORDERING INFORMATION
Example: nPP16 D ER LT
nPP16 Power/Relay Pack [blank] None [blank] None [blank] Auto On (Switch Ch. 1) [blank] 120/277VAC [blank] Standard
D 0-10VDC Dimming ER UL924 Emergency SW2 Auto On (Switch Ch. 2) 347 120/347VAC LT Low temp
output (via chase nipple) Operation SA Manual On (Switch Ch. 1)
DS 0-10VDC Dimming output
(via side slot) SA2 Manual On (Switch Ch. 2)
PA70 Auto On to 70% (Partial On)¹
PA Auto On to 50% (Partial On)¹
1. Requires D or DS option.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 1 of 3
T568B pin/pair assignment is recommended for all CAT-5e cables. For Supply Connections, use 14 AWG/90°C, 12 AWG/75°C or larger.
Diagram for non-dimming units Diagram for units with a dimming option (-D or -DS suffix)
Diagram for non-dimming units Diagram for units with a dimming option (-D or -DS suffix)
Normal3 Emergency Normal3 Emergency
(sense only) (sense only) EMERGENCY
VIO (low voltage 0-10 VDC
dim out)
Ballast or
GRY (low voltage
common) LED Driver
OPTIONAL (120VAC (120VAC
TEST
YEL Emer. Feed) 120 VAC OPTIONAL
YEL Emer. Feed) 120 VAC
SWITCH RED
(277VAC
Emer. Feed2)
OR TEST
SWITCH
nPP16 D ER RED
(277VAC
Emer. Feed2)
OR
BLK nPP16 ER
277 VAC1
or 277 VAC1
BLK
(Normal Feed)
BLU (Emer. Feed)
(Normal Feed)
nPP16 DS ER BLU (Emer. Feed)
green wire to an approved ground connection. Note: wires have 600V rated insulation. RJ-45 PORTS
• Interconnect unit (via RJ-45 ports) with other nLight devices in lighting zone using CAT-5e cables. LED
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 2 of 3
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
• Equipment should be mounted in locations and at heights where it will not be subjected to
tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an
unsafe condition.
• Turn power off, both normal and emergency sources before installation/servicing any
equipment connected to this unit.
• Do not use this equipment for other than its intended use.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 3 of 3
OVERVIEW
The nLight nPP16 family of power packs is the workhorse of an nLight system, delivering robust system
performance and design versatility for commercial and industrial lighting control applications. The nPP16
family is capable of switching loads up to 16 Amps via an internal latching relay designed with robust
SURWHFWLRQꢀIURPꢀWKHꢀKDUVKꢀVZLWFKLQJꢀUHTXLUHPHQWVꢀRIꢀ7ꢁꢀŴXRUHVFHQWꢀDQGꢀ/('ꢀORDGVꢂꢀ7KHVHꢀSRZHUꢀSDFNVꢀDOVRꢀ
provide nLight system bus power - up to 40mA from each of its two RJ-45 ports - by transforming Class 1
line voltage (120/277 VAC or 347 VAC) to Class 2 low voltage (15 VDC). This power is typically utilized by
other nLight devices within the power pack’s local control zone; however, remaining power is also made
available over the network for Bridges and devices in other zones to utilize.
FEATURES nPP16
•
•
Communicates w/ nLight Network
Self-Contained Relay Switches Line Voltage Load
Power/Relay Pack
• Supplies 40mA of Bus Power / RJ-45 port
• Optional out-of-box vacancy and partial-on modes
• 5HPRWHO\ꢀ&RQƓJXUDEOHꢃ8SJUDGHDEOH
• Push-Button Programmable
• &RQƓJXUDEOHꢀ5HOD\ꢀ/RJLF
• Extended Chase Nipple
• Plenum rated
SPECIFICATIONS
Size: (not including ½” chase nipple) 3.38” H x 2.53” W x 1.83” D (8.59 cm
x 6.43 cm x 4.65 cm) Model #: nPP16 (D) Model #: nPP16 (D) ER
Weight: 6 oz
Mounting: 1/2” Knockout
Color: White (standard), Red (ER)
nLight Network Ports: 2 RJ-45
Operating Voltage: 120/240/277VAC, 347VAC (with 347 option)
Max Load: 16A @ 120VAC/277VAC, 347VAC
Motor Load: 1/2 HP
Relay type: Latching
Frequency: 50/60Hz
Operating Temp: 14°F to 122°F (-10°C to 50°C)
Relative Humidity: 20-90% non-condensing
Bus Output Current/Voltage: 15 VDC, 40 mA / port (non-ER units only), 40 mA total at 240VAC
Max Dimming Load: Sinks 100mA; 0-10VDC dimmable ballasts or LED drivers
*If power pack is enclosed within a junction box, max ambient temperature is 45° C
RoHS Compliant, Title 24 System Component, Class 1 Listed, Plenum Rated, cULus Listed, CSA Listed
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢂ
ORDERING INFORMATION
Example: nPP16 D ER LT
nPP16 Power/Relay Pack [blank] None [blank] None [blank] Auto On (Switch Ch. 1) [blank] 120/277VAC [blank] Standard
D 0-10VDC Dimming ER UL924 Emergency SW2 Auto On (Switch Ch. 2) 347 120/347VAC LT Low temp
output (via chase nipple) Operation SA Manual On (Switch Ch. 1)
DS 0-10VDC Dimming output
(via side slot) SA2 Manual On (Switch Ch. 2)
PA70 Auto On to 70% (Partial On)¹
PA Auto On to 50% (Partial On)¹
1. Requires D or DS option.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 1 of 3
T568B pin/pair assignment is recommended for all CAT-5e cables. For Supply Connections, use 14 AWG/90°C, 12 AWG/75°C or larger.
Diagram for non-dimming units Diagram for units with a dimming option (-D or -DS suffix)
Diagram for non-dimming units Diagram for units with a dimming option (-D or -DS suffix)
Normal3 Emergency Normal3 Emergency
(sense only) (sense only) EMERGENCY
VIO (low voltage 0-10 VDC
dim out)
Ballast or
GRY (low voltage
common) LED Driver
OPTIONAL (120VAC (120VAC
TEST
YEL Emer. Feed) 120 VAC OPTIONAL
YEL Emer. Feed) 120 VAC
SWITCH RED
(277VAC
Emer. Feed2)
OR TEST
SWITCH
nPP16 D ER RED
(277VAC
Emer. Feed2)
OR
BLK nPP16 ER
277 VAC1
or 277 VAC1
BLK
(Normal Feed)
BLU (Emer. Feed)
(Normal Feed)
nPP16 DS ER BLU (Emer. Feed)
green wire to an approved ground connection. Note: wires have 600V rated insulation. RJ-45 PORTS
• Interconnect unit (via RJ-45 ports) with other nLight devices in lighting zone using CAT-5e cables. LED
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 2 of 3
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
• Equipment should be mounted in locations and at heights where it will not be subjected to
tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an
unsafe condition.
• Turn power off, both normal and emergency sources before installation/servicing any
equipment connected to this unit.
• Do not use this equipment for other than its intended use.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 3 of 3
OVERVIEW
The nLight nPP16 family of power packs is the workhorse of an nLight system, delivering robust system
performance and design versatility for commercial and industrial lighting control applications. The nPP16
family is capable of switching loads up to 16 Amps via an internal latching relay designed with robust
SURWHFWLRQꢀIURPꢀWKHꢀKDUVKꢀVZLWFKLQJꢀUHTXLUHPHQWVꢀRIꢀ7ꢁꢀŴXRUHVFHQWꢀDQGꢀ/('ꢀORDGVꢂꢀ7KHVHꢀSRZHUꢀSDFNVꢀDOVRꢀ
provide nLight system bus power - up to 40mA from each of its two RJ-45 ports - by transforming Class 1
line voltage (120/277 VAC or 347 VAC) to Class 2 low voltage (15 VDC). This power is typically utilized by
other nLight devices within the power pack’s local control zone; however, remaining power is also made
available over the network for Bridges and devices in other zones to utilize.
FEATURES nPP16
•
•
Communicates w/ nLight Network
Self-Contained Relay Switches Line Voltage Load
Power/Relay Pack
• Supplies 40mA of Bus Power / RJ-45 port
• Optional out-of-box vacancy and partial-on modes
• 5HPRWHO\ꢀ&RQƓJXUDEOHꢃ8SJUDGHDEOH
• Push-Button Programmable
• &RQƓJXUDEOHꢀ5HOD\ꢀ/RJLF
• Extended Chase Nipple
• Plenum rated
SPECIFICATIONS
Size: (not including ½” chase nipple) 3.38” H x 2.53” W x 1.83” D (8.59 cm
x 6.43 cm x 4.65 cm) Model #: nPP16 (D) Model #: nPP16 (D) ER
Weight: 6 oz
Mounting: 1/2” Knockout
Color: White (standard), Red (ER)
nLight Network Ports: 2 RJ-45
Operating Voltage: 120/240/277VAC, 347VAC (with 347 option)
Max Load: 16A @ 120VAC/277VAC, 347VAC
Motor Load: 1/2 HP
Relay type: Latching
Frequency: 50/60Hz
Operating Temp: 14°F to 122°F (-10°C to 50°C)
Relative Humidity: 20-90% non-condensing
Bus Output Current/Voltage: 15 VDC, 40 mA / port (non-ER units only), 40 mA total at 240VAC
Max Dimming Load: Sinks 100mA; 0-10VDC dimmable ballasts or LED drivers
*If power pack is enclosed within a junction box, max ambient temperature is 45° C
RoHS Compliant, Title 24 System Component, Class 1 Listed, Plenum Rated, cULus Listed, CSA Listed
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢂ
ORDERING INFORMATION
Example: nPP16 D ER LT
nPP16 Power/Relay Pack [blank] None [blank] None [blank] Auto On (Switch Ch. 1) [blank] 120/277VAC [blank] Standard
D 0-10VDC Dimming ER UL924 Emergency SW2 Auto On (Switch Ch. 2) 347 120/347VAC LT Low temp
output (via chase nipple) Operation SA Manual On (Switch Ch. 1)
DS 0-10VDC Dimming output
(via side slot) SA2 Manual On (Switch Ch. 2)
PA70 Auto On to 70% (Partial On)¹
PA Auto On to 50% (Partial On)¹
1. Requires D or DS option.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 1 of 3
T568B pin/pair assignment is recommended for all CAT-5e cables. For Supply Connections, use 14 AWG/90°C, 12 AWG/75°C or larger.
Diagram for non-dimming units Diagram for units with a dimming option (-D or -DS suffix)
Diagram for non-dimming units Diagram for units with a dimming option (-D or -DS suffix)
Normal3 Emergency Normal3 Emergency
(sense only) (sense only) EMERGENCY
VIO (low voltage 0-10 VDC
dim out)
Ballast or
GRY (low voltage
common) LED Driver
OPTIONAL (120VAC (120VAC
TEST
YEL Emer. Feed) 120 VAC OPTIONAL
YEL Emer. Feed) 120 VAC
SWITCH RED
(277VAC
Emer. Feed2)
OR TEST
SWITCH
nPP16 D ER RED
(277VAC
Emer. Feed2)
OR
BLK nPP16 ER
277 VAC1
or 277 VAC1
BLK
(Normal Feed)
BLU (Emer. Feed)
(Normal Feed)
nPP16 DS ER BLU (Emer. Feed)
green wire to an approved ground connection. Note: wires have 600V rated insulation. RJ-45 PORTS
• Interconnect unit (via RJ-45 ports) with other nLight devices in lighting zone using CAT-5e cables. LED
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 2 of 3
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
• Equipment should be mounted in locations and at heights where it will not be subjected to
tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an
unsafe condition.
• Turn power off, both normal and emergency sources before installation/servicing any
equipment connected to this unit.
• Do not use this equipment for other than its intended use.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com NPP16_FAMILY IS-NPP16 ER
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/18/17 3 of 3
OVERVIEW
The nLight nPP20 PL power pack extends the power pack family, delivering robust system
performance and design versatility for commercial and industrial control applications. The nPP20
PL is capable of switching loads up to 20 Amps for general purpose receptacle load via an internal
latching relay designed with robust protection. This power pack also has two available options
– the base unit powers off of line voltage, but does not provide nLight bus power. An option is
available for a unit that provides bus power – this option (BP) provides up to 40mA from each of
its two RJ-45 ports by transforming Class 1 line voltage (120 VAC) to Class 2 low voltage (15 VDC).
This power is typically utilized by other nLight devices within the power pack’s local control zone;
however, remaining power is also made available over the network for Bridges and devices in
other zones to utilize. Simply add this device into an nLight control zone with an occupancy sensor
and the unit will automatically switch off when the room becomes vacant. Local manual switch
nPP20 PL
and photocell control of receptacles is not typically required, therefore it is disabled by default. Plug Load Control Power
The nPP20 PL’s two RJ-45 connectors make control wiring with standard CAT5e cabling easy and
Pack
clean. For simplifying installation, the nPP20 PL is designed with an elongated chase nipple that
allows them to be attached directly through a ½” knockout into a junction box.
FEATURES
• Communicates w/ nLight Network
• Self-Contained Relay Switches Line Voltage Load
• BP Option Supplies 40mA of Bus Power / RJ-45 port
• Remotely Configurable/Upgradeable
• Push-Button Programmable
• Configurable Relay Logic
• Extended Chase Nipple
SPECIFICATIONS
Size:
(not including ½” chase nipple) 3.38” H x 2.53” W x 1.83” D
(8.59 cm x 6.43 cm x 4.65 cm)
Weight: 6 oz
Mounting: 1/2” Knockout
ꢀ
Color: Blue
nLight Network Ports: 2 RJ-45
Operating Voltage: 120VAC
Max Receptacle Load: 20A @ 120VAC - General Purpose per UL testing
Relay Type: Latching
Frequency: 50/60Hz
BusOutput Current/Voltage: (BP option only) 40mA / port @ 15VDC
ROHS Compliant, Title 24 System Component
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nPP20 PL Example: nPP20 PL BP
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 2
T568B pin/pair assignment is recommended for all CAT-5e cables. For Supply Connections, use 14 AWG/90°C, 12 AWG/75°C or larger.
WHT (neutral)
BLK (line in)
120 VAC
nPP20 PL
BLU (line in)
nPP20 PL - 911-00104-001
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 2 of 2
OVERVIEW
The nWSX LV / nWSX PDT LV series nLight wall switch occupancy sensor provides a simple
control solution for a small room, in particular one utilizing nLight enabled digital luminaires.
Capable of detecting small motion up to 20 ft (6.10 m), this sensor is perfect for private offices,
private rest rooms, copy rooms, closets or any small enclosed space. The nWSX LV uses Passive
Infrared (PIR) detection while the nWSX PDT LV utilizes PIR/Microphonics Dual Technology (PDT).
This stylish sensor can be programmed locally, via the front push-button(s), or remotely via the
nLight SensorView software. The nWSX LV/nWSX PDT LV includes an integrated photocell
(disabled by default).
nWSX LV
FEATURES
• 100% digitial PIR detection, vandal resistant lens standard, includes wall plate (screwless
nWSX PDT LV
sold separate) Low Voltage Wall Switch
• Push-button programmable, adjustable time delays, multiple operating modes Occupancy Sensor
• Multiple nWSX sensors or WallPods can be used in 3 way(or greater) configurations w/o
traveler wires
• Photocell standard (disabled by default) - Not available in night light versions
• Broadcasts occupancy, photocell, and switch information over a local and/or global nLight
channel
• Remotely firmware upgradeable
CONTROL MODES
A control zone with an nWSX LV / nWSX PDT LV can operate in several modes:
1. Auto On / Auto Off (i.e. Fully Automatic)
2. Manual On (initial state) to Override On (with expiration timer)
3. Auto On (initial state) to Override On (with expiration timer)
4. Manual On / Automatic Off (i.e. Semi-Automatic)
5. Manual On (initial state) to Fully Automatic nWSX LV nWSX LV NL nWSX LV DX
6. Predictive Off Switch (returns zone to auto-on unless person remained in room after an off nWSX PDT LV nWSX PDT LV NL nWSX PDT LV DX
switch press)
*See MLO operation chart on page 2.
SPECIFICATIONS
Size: 2.74” H x 1.68” W x 1.63” D
Weight: 5 oz
Mounting: Single gang switch box or low voltage ring
Bus power consumption: < 3mA
Wires: None
RoHS Compliant, Title 24 component
Warranty
Five-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
Specifications subject to change without notice.
Capable
This item is an A+ capable component, which has been designed and tested to provide out-of-the-box
luminaire compatibility with simple commissioning, when included as part of an A+ Certified™ Solution.
To learn more about A+, visit www.acuitybrands.com/aplus.
ORDERING INFORMATION
nWSX Example: nWSX LV WH LT
XX-Specify
Series Night Light or Dimming Color Temp/Humidity
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 1 of 2
COVERAGE PATTERN
• Small Motion (e.g. hand movements) detection up to 20 ft (6.10 m)
• Large motion (e.g. walking) detection greater than 36 ft (10.97 m)
• Wall to Wall Coverage
• Passive Dual Technology (Microphonics) provides overlapping detection of
human activity over the complete PIR coverage area. Advanced filtering is
utilized to prevent non-occupant noises from keeping the lights on.
SIDE VIEW
1.2 m
4 ft
0m 3 6 9 12
0 ft 9 18 27 36
Small motion
detection to ~20 ft
Large motion detection to >36 ft
CAT-5
To other nLight devices (optional) CAT-5
To other nLight
devices (optional)
BI-LEVEL SWITCHING USING MULTI-LEVEL OPERATING MODE WIRING to nLIGHT ENABLED DIGITAL LUMINAIRE (e.g. RTLED)
(MLO)
BLK - 120 V
ORN - 277 V
nPP16 CAT-5
CAT-5
LOAD A
CAT-5
To other nLight devices (optional)
BLK - 120 V
CAT-5
nPP16
ORN - 277 V NOTES:
• nLight enabled fixture must have nIO LEDG/nIO EZ PH for
To other nLight LOAD B
standalone operation
devices (optional) • Luminaires with nIO LEDG ER/nIO EZ PH ER require bus power from
another device
• Provides on/off and continuous raise/lower dimming operation by
default. For bi-level operation only program nWSX LV / nWSX PDT LV
MLO OPERATIONAL MODES for Multi-Level Operating Mode (MLO)
Additionally, an nWSX LV / nWSX PDT LV can be set to function in 2 State (Bi-Level) 2 State - Alternating 3 State Sequence
Multi-Level Operating Mode (MLO) which enables the user to select Sequence Sequence
from multiple on/off lighting states using just the unit’s single on/off Button
button. This mode is designed specifically for bi-level applications and Load A Load B Load A Load B Load A Load B
Press #
eliminates user confusion created when wall stations have multiple
buttons. Several different transition sequences are available in order 1 On Off On Off On Off
to comply with energy codes or user preference. Depending on the
sequence selected and initial lighting state, every subsequent button 2 On On Off On Off On
push steps through states according to below table. MLO sequences
are also available that enable high/low or low/high step operation via 3 Off Off Off Off On On
any nLight dimming output. 4 Off Off
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. 02/13/17 2 of 2
OVERVIEW
The WSX family of wall switch occupancy sensors provides simple and cost effective solutions for
commercial and residential lighting control applications. All WSX family sensors have a stylish low
SURƓOHꢀDSSHDUDQFHꢁꢀVRIWꢂFOLFNꢀEXWWRQVꢁꢀDQGꢀSURYLGHꢀVPDOOꢀPRWLRQꢀGHWHFWLRQꢀXSꢀWRꢀꢃꢄꢀIWꢀꢅꢆꢇꢈꢄꢀPꢉꢁꢀPDNLQJꢀ
WKHPꢀSHUIHFWꢀIRUꢀSULYDWHꢀRIƓFHVꢁꢀSULYDWHꢀUHVWꢀURRPVꢁꢀFORVHWVꢁꢀFRS\ꢀURRPVꢁꢀRUꢀDQ\ꢀRWKHUꢀVPDOOꢀHQFORVHGꢀ
VSDFHꢇꢀ$GGLWLRQDOO\ꢁꢀDOOꢀ:6;ꢀIDPLO\ꢀVHQVRUVꢀKDYHꢀDꢀSDWHQWꢂSHQGLQJꢀZLULQJꢀPHWKRGꢀWKDWꢀHQDEOHVꢀWKHPꢀWRꢀ
IXQFWLRQꢀHLWKHUꢀZLWKꢀRUꢀZLWKRXWꢀDꢀQHXWUDOꢀFRQQHFWLRQꢇꢀ:6;ꢀXQLWVꢀFRPHꢀSUHꢂFRQƓJXUHGꢀIRUꢀZLULQJꢀZLWKRXWꢀ
DꢀQHXWUDOꢁꢀKRZHYHUꢀLIꢀFRQQHFWLRQꢀWRꢀQHXWUDOꢀLVꢀUHTXLUHGꢀE\ꢀFRGHꢁꢀFRQWUDFWRUVꢀFDQꢀFRQYHUWꢀWKHꢀXQLWꢀLQꢀ
seconds.
SPECIFICATIONS
WSX D
Dimming Occupancy Wall
Size: ꢃꢇꢊꢋŐꢀ+ꢀ[ꢀꢈꢇꢆꢌŐꢀ:ꢀ[ꢀꢈꢇꢆꢍŐꢀ'ꢀꢅꢆꢇꢎꢆꢀFPꢀ[ꢀꢋꢇꢃꢊꢀFPꢀ[ꢀꢋꢇꢈꢋꢀFPꢉ Switch
ꢅQRWꢀLQFOXGLQJꢀJURXQGꢀVWUDSꢉ
Weight: 5 oz
Mounting: Single Gang Switch Box
0RXQWLQJꢀ+HLJKWꢏꢀ ꢍꢄꢂꢋꢌꢀLQꢀꢅꢊꢆꢇꢃꢂꢈꢃꢈꢇꢎꢀFPꢉ
Maximum Load/Pole: ꢅ5HOD\ꢉꢀꢌꢄꢄꢀ:ꢀ#ꢀꢈꢃꢄ9$&ꢁꢀꢈꢃꢄꢄꢀ:ꢀ#ꢀꢃꢊꢊ9$&ꢁꢀꢈꢐꢄꢄꢀ:ꢀ#ꢀꢍꢋꢊ9$&
Minimum Load: None
Motor Load: 1/4 HP
0D[ꢀ6LQNꢀ&XUUHQWꢏꢀ ꢐꢄꢀP$
ꢄꢂꢈꢄ9ꢀ'LPꢀ0LQꢀ2XWSXWꢏꢀ ꢑꢄꢇꢍꢀ9
)UHTXHQF\ꢏꢀ ꢐꢄꢒꢆꢄꢀ+]ꢀꢅWLPHUVꢀDUHꢀꢈꢇꢃ[ꢀIRUꢀꢐꢄ+]ꢉ
ROHS Compliant
Warranty
5-year limited warranty. Complete warranty terms located at:
ZZZꢇDFXLW\EUDQGVꢇFRPꢒ&XVWRPHU5HVRXUFHVꢒ7HUPVBDQGBFRQGLWLRQVꢇDVS[
Note: Actual performance may differ as a result of end-user environment and application.
6SHFLƓFDWLRQVꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢇ
ORDERING INFORMATION
WSX D Example: WSX PDTD 347 WH 8H
WSX Wall Switch Occupancy Sensor [blank] Passive Infrared (PIR) [blank] None D Dimming [blank] Automatic On
PDT Dual Technology EZ1 eldoLED Driver Compatibility SA Manual On
VA Vacancy
[blank] 120/277 VAC WH White AL Almond [blank] 10 VDC [blank] 0 VDC 4V 4 VDC
3472 347 VAC IV Ivory BK Black 9H 9 VDC 1V 1 VDC 5V 5 VDC
GY Gray RD4 Red Specify 8H 8 VDC 2V 2 VDC 6V 6 VDC
7H 7 VDC 3V 3 VDC
NOTES:
1. 0D[ꢀ'LPꢀ/HYHOꢀGHIDXOWꢀVHWꢀWRꢀꢎꢇꢈ9'&ꢇꢀꢀ0LQꢀ'LPꢀ/HYHOꢀGHIDXOWꢀVHWꢀWRꢀꢈꢇꢐ9'&
2. :DOOꢀSODWHGꢀLQFOXGHGꢀIRUꢀZKLWHꢀRUꢀLYRU\ꢀRQO\ꢀIRUꢀꢍꢋꢊꢀ9$&ꢀXQLWV
3. 0DWFKLQJꢀZDOOꢀSODWHꢀSURYLGHGꢀIRUꢀꢈꢃꢄꢒꢃꢊꢊꢀ9$&ꢀXQLWV
4. Special order
5. For setting other than default, minimum order quantity of 30 units
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com WSX D
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/02/17 1 of 4
COVERAGE PATTERNS
• Small motion (e.g. hand movements) detection up to 20 ft (6.10 m), ~625 ft2 20 6 Small TOP VIEW
• Large motion (e.g. walking) detection greater than 36 ft (10.97 m), ~2025 ft2 motion
detection
NOTES:
1.) Per NEC requirements, the 0-10V violet and gray wires must be installed as Class One.
2.) The 0-10V control wires must not exceed 250 ft (76 m) in length and must be sized at no less than 20AWG.
NO DAYLIGHT
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com WSX D
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/02/17 2 of 4
OPERATIONAL SETTINGS
2 = Occupancy Time Delay 6 = Daylight Set-Point
The length of time an occupancy sensor will keep the lights on after it last detects The ambient light level at which the sensor sets the lights to the Low Trim setting. 14 = Manual On Grace Period
occupancy. 1 - Set Now** 5 - 8 fc 9 - 48 fc 13 - 128 fc Time period after lights automatically turn off that they can be reactivated by
1 - Test Mode** 5 - 7.5 min 9 - 17.5 min 13 - 27.5 min motion. Applicable only when sensor is in Manual On (Semi Auto) mode.
2 - 0.1 fc 6 - 16 fc 10 - 64 fc* 14- 192 fc 1 - 0 sec 3 - 15 sec*
2 - 30 sec 6 - 10.0 min* 10 - 20.0 min 14 - 30.0 min
3 - 1 fc 7 - 24 fc 11 - 80 fc 15 - 256 fc
3 - 2.5 min 7 - 12.5 min 11 - 22.5 min
4 - 4 fc 8 - 32 fc 12 - 96 fc
4 - 5.0 min 8 - 15.0 min 12 - 25.0 min
**Set Now will automatically select the Daylight Set-Point based on the current
15 = Dimming Range Max (High Trim)
The maximum output level of the sensor.
**Test mode sets Occupancy Time Delay to 30 seconds, and increases photocell conditions in the room. Lights will go to full dim and sensor will rapid flash for 15
transition rate in addition to disabling the microphone on units with Dual seconds allowing occupant to move out of direct view of sensor. Once the set-point 1 - 0 VDC 5 - 3 VDC 9 - 7 VDC 13 - 10 VDC*
Technology. selection is completed, the sensor will double-blink in confirmation. 2 - 1 VDC 6 - 4 VDC 10 - 8 VDC
Button will turn lights off and keep them off until pressed again. The lights will 2 - 30 sec 6 - 10 min 10 - 20 min 17 = Predictive Exit Time
remain off until the button is pressed again, restoring the sensor to Automatic On Time period after manually switching lights off for occupant to leave the space.
mode. 3 - 2.5 min 7 - 12.5 min 11 - Stays at dim (never off) Applicable only when sensor is in Predictive Off mode.
Switch Disable 1 - 5 sec 4 - 8 sec 7 - 15 sec
4 - 5 min 8 - 15 min
User is prevented from turning off the lights via the push-button. 2 - 6 sec 5 - 9 sec 8 - 20 sec
Predictive Mode
Pressing the push-button switch overrides the lights off and temporarily disables 9 = Restore Defaults 3 - 7 sec 6 - 10 sec* 9 - 30 sec
the occupancy detection. After 10 seconds, the occupancy detection reactivates Returns all functions to original settings.
and monitors for an additional 30 seconds. If no occupancy is detected during this
1 - Maintain Current*
period, the sensor will revert to Automatic On operation. If occupancy is detected, 18 = Predictive Grace Time
the sensor will remain in Override Off mode and requires the switch to be pressed 2 - Restore Defaults Time period after Predictive Exit Time that sensor rescans the room for remaining
again in order to restore the sensor to Automatic On. occupants. Applicable only when sensor is in Predictive Off mode.
Predictive Mode with Expiration 1 - 0 sec 4 - 20 sec 7 - 50 sec
Pressing the push-button switch overrides the lights off and temporarily disables
10 = Minimum On Time
Required initial time for lamps to be on after each switch on, regardless of 2 - 5 sec 5 - 30 sec* 8 - 60 sec
the occupancy detection. After 10 seconds, the occupancy detection reactivates
occupancy status. Once met, lights resume following occupancy time delay.
and monitors for an additional 30 seconds. If no occupancy is detected during this
period, the sensor will revert to Automatic On operation. 1 - 0 min (disabled)* 4 - 45 min 3 - 10 sec 6 - 40 sec
1 - Switch Enable 3 - Predictive Mode 2 - 15 min 5 - 60 min
2 - Switch Disable 4 - Predictive Mode with Expiration* 3 - 30 min 19 = Fade On Rate
Time required for light to reach preset level.
5 = Darkness Set-Point/ Inhibit Set-Point 1 - 0.75 sec* 3 - 5 sec
The ambient light level at which the sensor sets the lights to the High Trim setting. 11 = LED Operation
Indicates behavior of device’s LED. 2 - 2.5 sec 4 - 15 sec
1 - Set Now** 5 - 8 fc 9 - 48 fc 13 - 128 fc
1 - Occupancy Indication*
2 - 0.1 fc 6 - 16 fc 10 - 64 fc 14- 192 fc
2 - Disabled 20 = Fade Off Rate
3 - 1 fc 7 - 24 fc* 11 - 80 fc 15 - 256 fc Time required for light to turn Off.
1 - 0.75 sec 3 - 5 sec
4 - 4 fc 8 - 32 fc 12 - 96 fc 12 = Dual Technology (Microphonics™)
The secondary method of occupancy detection that allows the sensor to hear 2 - 2.5 sec* 4 - 15 sec
**Set Now will automatically select the Darkness Set-Point based on the current
occupants.
conditions in the room. Lights will go to full bright and sensor will rapid flash for
1 - Normal* 4 - Low
15 seconds allowing occupant to move out of direct view of sensor. Once the set-
point selection is completed, the sensor will double-blink in confirmation. 2 - Off 5 - Phase Off (15-10-5 min)
21 = Start Level
Level of light output when occupancy is initially detected. Not applicable in
3 - Medium Automatic Dimming Control (ADH) mode.
1 - 10% 4 - 40% 7 - 70% 10 - 100%*
2 - 10 sec* 6 - 50 sec
3 - 20 sec 7 - 60 sec
4 - 30 sec
* Default Setting
1. Not Applicable with Vacancy (VA) Option
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com WSX D
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/02/17 3 of 4
PROGRAMMING INSTRUCTIONS
Operational settings can be changed via the push-button sequence outlined below (note the example used is for changing occupancy time delay).
e.g., press 5x
to change
to 7.5 min
5. 6. Fade
Start
Level
Time
Delay On
Mode
Switch
7.
On Modes
2x 3x
20x 21x
Rate
Darkness
Pred
Grace 19x 4x Set-Point
18x 5x Daylight
Pred PROGRAMMING
While LED Exit 17x 6x Set-Point LED FLASHES
flashes back new Low 16x 7x Photocell CONFIRMATION
Mode
Trim
setting 10x... 15x PRESS BUTTON 8x TWICE
High 14x 9x Dim to
Off
COMPLETE
Trim
13x 10x
Man 12x 11x Defaults
e.g., 5 flashes On
Grace Mic
confirms new Grace Dual LED
Tech Operation e.g., press 2x (for Occupancy
7.5 min time
Time Delay) to save and exit
delay setting
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com WSX D
© 2014-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 02/02/17 4 of 4
Interior Lighting
Specification Section: 26 51 00
January 8, 2018
ELECTRICAL SUBCONTRACTOR
Bergelectric Corporation
650 Opper Street
Escondido, CA 92029
GENERAL CONTRACTOR
Cannon Building
1861 E. Miraloma Ave.
Placentia, CA 92123
ARCHITECT ENGINEER
Ewing Cole Ewing Cole
15231 Laguna Canyon Road, Suite #200 15231 Laguna Canyon Road, Suite #200
Irvine, CA 92618 Irvine, CA 92618
650 Opper Street, Escondido, CA 92029 - Tel (760) 746.1003 Fax (760) 741.0918 - License No. C10-85046
C1727 ELS THV
16010-10 Submittal
FOR REVIEW Page 61 of 110 01/08/2018
TABLE OF CONTENTS
Interior Lighting
Specification Section: 26 51 00
TAB # 1
Interior Lighting
Interior Lighting
Specification Section: 26 51 00
C1727 ELS THV
16010-10 Submittal
FOR REVIEW Page 64 of 110 01/08/2018
Lighting Fixture
Submittal
Job Name:
EDWARDS LIFESCIENCES
THV
Prepared For:
BERGELECTRIC
Date:
JANUARY 5, 2018
C1727 ELS THV
16010-10 Submittal
FOR REVIEW Page 65 of 110 01/08/2018
PROJECT INFORMATION
Fixture Type
CSEDI SERIES – LED – INSET DOOR
Catalog Number
PRODUCT FEATURES:
» High-output, high-CRI LED lamp sources for accurate color rendition Approved by
and lighting performance
» Diffused high-efficiency lens for reduced glare
» Recessed ceiling mount; grid or flange - 1'×4' (30.48cm×121.92cm),
2'×2' (60.96cm×60.96cm), 2'×4' (60.96cm×121.92cm)
» Suitable for universal installation into 1.0" (2.54cm) and 1.5" (3.81cm)
grid or flange (drywall) ceilings
» One piece inset doorframe, secured to housing with aircraft cables.
In Stock SKU
BSL
LED C
IP65 K230 ISO 5
Class 100
CCEA
Approved 1-2 CSEDI-24-90L40K-DCC-DV-5F-2H-SYM
CSEDI_14_22_24-013117
SIMPLESEAL™
CSEDI SERIES – TECHNICAL DATA
PERFORMANCE Initial Delivered Lumens
Displayed information is for selected luminaires only. Additional wattages and color temperatures are also available.
Visit www.kenall.com for additional information.
CSEDI_14_22_24-013117
SIMPLESEAL™
CSEDI SERIES – TECHNICAL DATA
PERFORMANCE
Model: CSEDI14-67L40K-DCC-1-DV-2F-2H Model: CSEDI22-67L40K-DCC-1-DV-2F-2H Model: CSEDI22-90L40K-DCC-1-DV-2F-2H-SYM
3616 3349 4304
1 1
Maximum Candela = 3616 Located At Horizontal Angle = 15, Vertical Angle = 5 Maximum Candela = 3349 Located At Horizontal Angle = 0, Vertical Angle = 0 Max Candela = 4304 Located At Horizontal Angle = 0, Vertical Angle = 0
1 - Vertical Plane Through Horizontal Angles (15-195) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0-180) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.)
2 - Horizontal Cone Through Vertical Angle (5) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.)
1
1
Maximum Candela = 3470 Located At Horizontal Angle = 0, Vertical Angle = 0 Maximum Candela = 4460 Located At Horizontal Angle = 0, Vertical Angle = 0 Max Candela = 8620 Located At Horizontal Angle = 0, Vertical Angle = 5
1 - Vertical Plane Through Horizontal Angles (0-180) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0-180) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.)
2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (5) (Through Max. Cd.)
DIMENSIONAL DATA
Fixture
Housing
Lens Retention A C
Bracket
Lens
D
Inset Doorframe Door B
Gasket
CSEDI_14_22_24-013117
PROJECT INFORMATION
Fixture Type
CSEDI SERIES – LED – INSET DOOR
Catalog Number
PRODUCT FEATURES:
» High-output, high-CRI LED lamp sources for accurate color rendition Approved by
and lighting performance
» Diffused high-efficiency lens for reduced glare
» Recessed ceiling mount; grid or flange - 1'×4' (30.48cm×121.92cm),
2'×2' (60.96cm×60.96cm), 2'×4' (60.96cm×121.92cm)
» Suitable for universal installation into 1.0" (2.54cm) and 1.5" (3.81cm)
grid or flange (drywall) ceilings
» One piece inset doorframe, secured to housing with aircraft cables.
In Stock SKU
BSL
LED C
IP65 K230 ISO 5
Class 100
CCEA
Approved 1-2 CSEDI-24-90L40K-DCC-DV-5F-2H-SYM
CSEDI_14_22_24-013117
SIMPLESEAL™
CSEDI SERIES – TECHNICAL DATA
PERFORMANCE Initial Delivered Lumens
Displayed information is for selected luminaires only. Additional wattages and color temperatures are also available.
Visit www.kenall.com for additional information.
CSEDI_14_22_24-013117
SIMPLESEAL™
CSEDI SERIES – TECHNICAL DATA
PERFORMANCE
Model: CSEDI14-67L40K-DCC-1-DV-2F-2H Model: CSEDI22-67L40K-DCC-1-DV-2F-2H Model: CSEDI22-90L40K-DCC-1-DV-2F-2H-SYM
3616 3349 4304
1 1
Maximum Candela = 3616 Located At Horizontal Angle = 15, Vertical Angle = 5 Maximum Candela = 3349 Located At Horizontal Angle = 0, Vertical Angle = 0 Max Candela = 4304 Located At Horizontal Angle = 0, Vertical Angle = 0
1 - Vertical Plane Through Horizontal Angles (15-195) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0-180) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.)
2 - Horizontal Cone Through Vertical Angle (5) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.)
1
1
Maximum Candela = 3470 Located At Horizontal Angle = 0, Vertical Angle = 0 Maximum Candela = 4460 Located At Horizontal Angle = 0, Vertical Angle = 0 Max Candela = 8620 Located At Horizontal Angle = 0, Vertical Angle = 5
1 - Vertical Plane Through Horizontal Angles (0-180) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0-180) (Through Max. Cd.) 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.)
2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) 2 - Horizontal Cone Through Vertical Angle (5) (Through Max. Cd.)
DIMENSIONAL DATA
Fixture
Housing
Lens Retention A C
Bracket
Lens
D
Inset Doorframe Door B
Gasket
CSEDI_14_22_24-013117
Catalog
Number
Notes
INDUSTRIAL IBG
Page 1 of 11
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: IBG 24000LM SEF AFL GND MVOLT OZ10 40K 80CRI DWH
Performance Color
Series Nominal lumens package Lens Distribution Voltage Driver temperature
IBG 8000LM 8,000 lumens2 30000LM 30,000 lumens SEF Standard AFL Acrylic, frosted WD Wide MVOLT 120-277V OZ10 0-10V 30K 3000 K
IBGN1 12000LM 12,000 lumens 36000LM 36,000 lumens efficiency ACL Clear acrylic GND General HVOLT 347-480V3 dimming2 35K 3500 K
15000LM 15,000 lumens 48000LM 48,000 lumens HEF Premium PCL Clear polycarbonate ND Narrow 120 120V AZ10 0-10V 40K 4000 K
efficiency dimming,
18000LM 18,000 lumens 60000LM 60,000 lumens PFL Semi-diffuse FD Focus 208 208V aux. 50K 5000 K
24000LM 24,000 lumens polycarbonate 240 240V output6
L/LENS Less lens 277 277V
347 347V4
480 480V4,5
Coloring
rendering index Options Finish
70CRI 70 CRI HA High ambient 7
Cord sets: Controls: 20
DNA Natural
80CRI 80 CRI SPD Surge protection device8 CS1W Straight plug, HLN360 Haleon 360° High Mount Occ Sensor, pre-wired; aluminum
90CRI 90 CRI BPK Fixture backpack9 120V17 Bluetooth® DWH Gloss white
PS1050 Emergency battery pack10 CS3W Twist-lock, 120V17 HLN360HL Haleon 360° High Mount Occ Sensor w/HL Default, pre-
CS7W Straight plug, wired; Bluetooth®
PS10250 Emergency battery pack11 HLN360ADC Haleon 360° High Mount Occ Sensor w/ADC Default,
277V17
PS30250 Emergency battery pack12 CS11W Twist-lock, 277V17 pre-wired; Bluetooth®
BGTD Generator transfer CS25W Twist-lock, 347V17 HLN360ANL Haleon 360° High Mount Occ Sensor w/ANL Default,
device13 pre-wired; Bluetooth®
SF Single fuse14 CS97W Twist-lock, 480V17 HLNASL Haleon High Mount Aisleway Occ Sensor, pre-wired;
DF Double fuse15 CS93W 600 SO white Bluetooth®
cord, no plug (no HLNASLHL Haleon High Mount Aisleway Occ Sensor w/HL Default,
OUTCTR Wiring leads pulled voltage required)
through back center of pre-wired; Bluetooth®
fixture16 CS93W5CD 600 SO HLNASLADC Haleon High Mount Aisleway Occ Sensor w/ADC Default,
5-conductor pre-wired; Bluetooth®
OCS RELOC® OnePass® white cord, no
selectable cable 6' HLNASLANL Haleon High Mount Aisleway Occ Sensor w/ANL Default,
plug (no voltage pre-wired; Bluetooth®
installed 17, 18 required)
OCU__ RELOC® OnePass® LAOZU 360° high mount motion sensor, pre-wired
unselectable cable 6' LAH0SZU 360° high mount motion sensor with dimming, pre-wired
installed (must specify
tap position)17 LAPZU 360° high mount motion sensor with photocell, pre-
IMP Integrated modular wired
plug 19 LAM0SZU 360° high mount motion sensor, dimming & switching
RRL_ RELOC®-Ready luminaire. photocell, pre-wired
See page 10 for ordering C6D0SUEM 360° high mount motion sensor, dimming & switching
information photocell capable, pre-wired; UL924 listed21
WGX Standard wire guard, C10D0SUEM 360° low mount motion sensor, dimming & switching
installed photocell capable, pre-wired; UL924 listed21
nPP16D nLight® dimming & switching module22
nPP16DER nLight® dimming & switching module with emergency
relay22
nMSI nLight® high mount aisleway motion sensor, pre-wired22
nMSI360 nLight® 360° high mount motion sensor, pre-wired22
nMSID nLight® high mount aisleway motion sensor with
dimming, pre-wired22
nMSI360D nLight® 360° high mount motion sensor with dimming,
pre-wired22
MSI6XADL DSCXADL XPoint™ Wireless 360° high mount motion sensor with
photocell
XPW XPoint™ Wireless 0-10V relay, external (utilizes XPA
CMRB0) 55°C max ambient
XAD XPoint™ Wireless 0-10V relay, internal, lower max
ambient23
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 2 of 11
Notes 13 Requires BPK option. 120 or 277V only. Not available with PS1050, PS10250, PS30250. Not available with 347 or
1 Available with 18000LM, 24000LM, 30000LM and 36000LM only. 480V when ordered in combination with XAD or XPW. For ambient temperatures up to 113°F (45°C).
2 Not available with Haleon sensor controls options. 14 Available on 120, 277, 347V. Not available with MVOLT or HVOLT.
3 Not available with 8000LM. Not available with BTGD, nPP16D, nPP16DER, PS1050, PS10250, PS30250 or XAD. 15 Available on 208, 240, 480V. Not available with MVOLT or HVOLT.
4 When ordered with 8000LM voltage selected utilizes the fixture back pack. 16 Not available with BPK option. Requires IBGPMPHB accessory to mount fixture. Not available with Cord Set
options.
5 Not available with nPP16D or nPP16DER.
17 Must specify voltage.
6 Only available with Haleon sensor controls options.
18 Cannot be used in dimming applications, must use RRLC12S
7 55 C when suspended, 45 C when surface mounted. Not available with BGTD, PS1050, PS10250, PS30250, XAD,
or XPW. 19 Not available with BPK, nPP16D, nPP16DER, nMSI, nMSI360, PS1050, PS10250, or PS30250.
8 Standard with HVOLT, 347, or 480V - only specify for MVOLT, 120, 208, 240, or 277V. Standard with Motion sen- 20 Must specify voltage. Refer to page 7 for Haleon sensor default settings matrix. Refer to page 9 for additional
sors/controls, BGTD & Power Sentry battery options. LSXR ordering options. Refer to page 10 for additional C6D0SUEM and C10D0SUEM information.
9 Required with PS1050, PS10250, PS30250, BGTD. Required with 8000LM when ordered with 347/480V. 21 Daylight harvesting functionality not enabled by default. See page 10 for default sequence of operation.
Required with Xpoint controls when order with 347/480V. Not available with nLight. Not for use with THUN 22 Not available with 208V, 240V, or 480V.
mount (surface). 23 Not available with HVOLT. When ordered with 347V or 480V, BPK option is required. Not available with HA
10 Requires BPK option. Available 120-277V only. Available with 8000LM only. For ambient temperatures of 32°F option.
to 122°F (0°C to 50°C). Not available with IMP. 24 Maximum ambient temperature of standard fixture mounted with THUN is 95°F (35°C). With HA option 113°F
11 Requires BPK option. Available 120-277V only. Not available with 8000LM. For ambient temperatures of 50°F to (45°C). Not available with MSIIMPIBG or MSI360IMPIBG options.
122°F (10°C to 50°C).Not available with IMP.
12 Requires BPK option. 120 or 277V only. Not available with 8000LM. For ambient temperatures of 32°F to 122°F
(0°C to 50°C). Not available with IMP.
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 3 of 11
25.60 25.60
25.60
47.28
5.77
BPK OPTION
47.28
5.48
PS30250 OPTION
20.71 47.28
2.68
IBG 36000LM 48000LM 60000LM
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 4 of 11
PHOTOMETRICS
See www.lithonia.com.
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 5 of 11
IBGN CHARACTERISTICS
Wattage
Length Width Depth
Lumen Standard efficiency High efficiency
package
120V 277V 347V 480V 120V 277V 347V 480V Dimensions are shown in inches (centimeters)
unless otherwise noted.
18000LM 117 114 115 114 104 102 101 101 47.29 11.75 2.75
24000LM 172 170 167 167 152 150 153 153 47.29 11.75 2.75
30000LM 209 205 208 207 183 180 179 178 47.29 11.75 2.75
36000LM 246 240 242 243 207 203 202 201 47.29 11.75 2.75
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 6 of 11
IBGN 5 41 1.03
Operating hours 0 15,000 30,000 45,000 60,000 100,000 10 50 1.02
Lumen maintenance factor 1 0.97 0.93 0.90 0.87 0.81 20 68 1.01
25 77 1.00
30 86 0.99
AMBIENT TEMPERATURE RATINGS 35 95 0.99
Mounting Suspended Surface 40 104 0.98
Standard temperature rating 113°F (45°C) 95°F (35°C) 45 113 0.97
HA option temperature rating 131°F (55°C) 113°F (45°C) 50 122 0.96
55 131 0.96
HLNxxx
10 minutes Disabled Disabled Disabled Disabled Disabled
Occupancy Only
HLNxxxHL
10 minutes Disabled Disabled 10% 100% 2.5 minutes
0-10V Dimming
HLNxxxADC
10 minutes On/Off/Dim 4 fc 10% 100% 0 seconds
Dim & Switch Photocell
HLNxxxANL
Dim & Switch Photocel with 10 minutes On/Off/Dim 4 fc 10% 100% Stay Dim/ Never Off
High/Low Occ Op
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 7 of 11
40 12
12 6.1 0m 6.1 12
20 6.1
40 20 0 ft 20 40
40 12
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 8 of 11
SELECTIONS BELOW WILL EXTEND ORDER LEAD TIME. CONSULT YOUR SALES REPRESENTATIVE FOR DETAILS.
SINGLE RELAY
ORDERING INFORMATION Example: LAH0SZU
Default occupancy
Series Lens option Dimming/Photocell Max. dim level Min. dim level Temp/Humidity time delay
L LSXR passive A High mount, O None1 0 10 VDC S Minimum dim Z None I 30 sec
infrared indoor 360° H High/low occupancy 9 9 VDC level of ballast T Low temperature2 D 2.5 min
occupancy sensor B Low mount, operation 1 1 VDC
8 8 VDC X 5.0 min
360° P Switching photocell 2 2 VDC
7 7 VDC R 7.5 min
C High mount (on/off)1 3 3 VDC
aisleway U 10.0 min
M Dimming and 4 4 VDC (with minimum 15
switching photocell minute on time)
5 5 VDC
G Dimming and V 15.0 min
switching photocell 6 6 VDC
with high/low oc- W 20.0 min
cupancy operation Y 30.0 min
Notes
1 Max and min dim levels not applicable with this option.
2 Ambient temperature rating of -4°F (-20°C) to 131°F (55°C).
Series Lens option Poles Operating mode Temp/Humidity Default occupancy time delay
L LSXR passive infrared A High mount, 360° 2 Dual relay J None Z None I 30 sec
indoor occupancy sensor B Low mount, 360° K Alternating off relays (promotes even lamp wear) T Low temperature1 D 2.5 min
C High mount aisleway O Alternating off relays w/photocell X 5.0 min
P Switching photocell(on/off) R 7.5 min
E Photocell on/off (pole 1 only) U 10.0 min (with minimum
F Photocell on/off - both poles (dual set-point) 15 minute on time)
V 15.0 min
W 20.0 min
Y 30.0 min
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 9 of 11
6 3 0m 3 6 9.1 6 3 0m 3 6 9.1
20 10 0 ft 10 20 30 20 10 0 ft 10 20 30
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 10 of 11
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: RRLA
RRL RELOC®-ready luminaire A Hot conductor wired to position #1 (phase A); non-dimming AE Hot conductor wired to position #1 (phase A), hot conductor #2 wired to position
#2 (phase B); non-dimming 2
B Hot conductor wired to position #2 (phase B); non-dimming ABE Hot conductor wired to position #1 (phase A), hot conductor #2 wired to position
#2 (phase B), inverter conductor wired to position #3 (phase C); non-dimming 1,2
C Hot conductor wired to position #3 (phase C); non-dimming 1 C12S Hot conductor in position #1 (phase A), low voltage conductor #1 in position
#2,low voltage conductor #2 in position #3; dimming 1,3
AB Outboard hot conductor wired to position #1 (phase A), inboard hot
conductor wired to position #2 (phase B); non-dimming
Compatible RELOC® Cables for Industrial Luminaires (ordered and shipped separately)
(click to view RELOC product page for more information)
OCS OCU OD
Notes
1 C, ABE, and C12S options are not used with Quick-Flex QFC,
QSFC, QPT, and QD.
2 AE and ABE commercial fixtures should disconnect the TSPL be-
fore unplugging the RRL so it does not go into discharge mode.
3 C12S option is used with the OnePass OD and 820 SSC, PT, and
DC for 0-10V/DALI applications.
DC PT
IBG
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/17/17
Page 11 of 11
Catalog
Number
Notes
2VTL
include integral T-bar clips. Fixture may be mounted and wired in continuous rows. Total fixture height is only 4-3/8".
OPTICS — Volumetric illumination is achieved by creating an optimal mix of light to walls, partitions, vertical ADP
and horizontal work surfaces — rendering the interior space, objects and occupants in a more balanced,
complementary luminous environment. Linear faceted reflector cavity softens and distributes light into
the space while minimizing luminous contrast between the fixture and ceiling. Sloped end plates provide
a smooth, luminous transition between fixture and ceiling while enhancing the perception of fixture depth.
High-performance diffuser provides LED concealment, even illumination across the diffuser and improved
2' x 4'
lumen-per-watt performance. LED
Now available with two different aesthetics including the standard Acrylic Linear Prismatic Diffuser (ADP) and the Acrylic ADPT
Linear Prismatic Diffuser with Diffuser Trim Rings (ADPT).
ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality
of illumination for extended service life. 80% LED lumen maintenance at 60,000 hours (L80/60,000).
eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free,
low-current inrush, 89% efficiency and low EMI.
Optional integrated nLight® controls make each luminaire addressable - allowing it to digitally communicate
with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply
connect all the nLight enabled control devices and the VTL luminaires using standard Cat-5 cabling. Unique
plug-and-play convenience as devices and luminaires automatically discover each other and self-commission.
Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that
actively manages the LED light source so that constant lumen output is maintained over the system life,
preventing the energy waste created by the traditional practice of over-lighting.
Step-level dimming option allows system to be switched to 50% power for compliance with common energy
codes while maintaining fixture appearance.
Driver disconnect provided where required to comply with US and Canadian codes.
SENSOR— Integrated sensor (individual control): Sensor Switch MSD7ADCX (Passive infrared (PIR))
or MSDPDT7ADCX (PIR/Microphonics Dual Tech (PDT)) integrated occupancy sensor/automatic dimming
Dimensions
photocell allows the luminaire to power off when the space is unoccupied or enough ambient light is entering All dimensions are inches (centimeters) unless otherwise specified.
the space. See page 2 for more details on the integrated sensor.
Integrated Sensor (nLight Wired Networking): This sensor is nLight-enabled, meaning it has the ability Specifications
to communicate over an nLight network. When wired, using CAT-5 cabling, with other nLight-enabled
sensors, power packs, or WallPods, an nLight control zone is created. Once linked to a Gateway, directly or Length: 48 (122.0) 4-3/8
(11.1)
via a Bridge, the zone becomes capable of remote status monitoring and control via SensorView software. Width: 24 (61.0)
See page 2 for the nLight sensor options.
Depth: 4-3/8 (11.1) 8-1/4
Integrated Smart Sensor (nLight Air Wireless Platform): The rES7 sensor is nLight AIR enabled, meaning (21)
it has the ability to communicate over the wireless nLight control platform. It is both a digital PIR occupancy 24
sensor/automatic dimming photocell. It pairs to other luminaires and wall switches through our mobile (61.0)
app, CLAIRITY, which allows for simple sensor adjustment. See page 3 for more details on the Integrated
Smart Sensor.
INSTALLATION — Unique grid interfacing arrangement provides mounting into standard 1" and 9/16"
tee bar or screw slot grids. 9/16" allows fixture trim to hang level with architectural ceiling tiles. Drywall
ceiling adaptors available. Suitable for damp location.
LISTINGS — CSA Certified to meet U.S. and Canadian standards. IC rated. DesignLights Consortium® (DLC)
Premium qualified product. Not all versions of this product may be DLC Premium qualified. Please check
the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified.
WARRANTY — 5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
NOTE: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specifications subject to change without notice.
Capable Luminaire
This item is an A+ capable luminaire, which has been designed and tested
to provide consistent color appearance and out-of-the-box control compatibility
with simple commissioning.
• All configurations of this luminaire meet the Acuity Brands’ specification for
chromatic consistency
• This luminaire is part of an A+ Certified solution for nLight® or XPoint™ Wireless
control networks when ordered with drivers marked by a shaded background*
To learn more about A+, visit www.acuitybrands.com/aplus.
*See ordering tree for details
LED 2VTL2X4
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: 2VTL4 40L ADPT EZ1 LP840 MSD7ADCX
2VTL4
2VTL4 2X4 VTL (blank) Static 30L 3000 lumens ADP Acrylic linear prismatic (blank) MVOLT EZ1 eldoLED dims to 1%, 0-10V
H Heat removal 40L 4000 lumens ADPT Acrylic linear prismatic 347 347V2 EZB eldoLED dims to dark, 0-10V
48L 4800 lumens with diffuser trim rings EDB eldoLED DALI3
60L 6000 lumens EXB eldoLED DMX/RDM3
72L 7200 lumens SLD Step-level dimming3
EXA1 Dims to 1%, XPoint wireless enabled4
EXAB Dims to dark, XPoint Wireless enabled4
LP830 3000 K, 80 CRI (blank) No nLight® (blank) No sensor control EL7L 700 lumen battery
LP835 3500 K, 80 CRI N80 nLight® with 80% lumen nLight Wired Networking pack (non-CEC
management compliant)
LP840 4000 K, 80 CRI NES7 nLight® nES 7 PIR integral occupancy sensor7,10
N80EMG nLight® with 80% lumen EL14L 1400 lumen battery
LP850 5000 K, 80 CRI NESPDT7 nLight® nES PDT 7 dual technology integral occupancy control7,10 pack (non-CEC
management for use with
generator supply EM power5 NES7ADCX nLight® nES 7 ADCX PIR integral occupancy sensor with automatic compliant)
dimming photocell7,10 EL14LSD 1400 lumen battery
N100 nLight® without lumen
management NESPDT7ADCX nLight® nES 7 PDT 7 dual technology intergral occupancy sensor with pack with self-
automatic dimming photocell7,10 diagnostic testing
N100EMG nLight® without lumen feature (non-CEC
management for use with Individual Control compliant) 12
generator supply EM power5 MSD7ADCX PIR integral occupancy sensor with automatic dimming control E10WLCP EM Self-Diagnostic
NLTAIR nLight AIR enabled6 photocell3,7,11 battery pack, 10W
MSDPDT7ADCX PDT integral occupancy sensor with automatic dimming control Constant Power, CEC
photocell3,7,11 compliant
Xpoint Wireless CP Chicago plenum
XADS7 XPoint™ wireless controller and micro 360° PIR occupancy and
photocell sensor3,4,9
nLight Wireless Networking
RES7N nLight® AIR PIR integral occupancy sensor with automatic
dimming photocell for Networking Capabilities 7,10
nLight Wireless Zone
RES7Z nLight® AIR PIR integral occupancy sensor with automatic
dimming photocell for zone control 7,10
2VTL2X4
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2011-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/09/17
Sequence of Operation
MOTION NO MOTION MOTION
MAX
MIN
LIGHTS ON 17.5 MIN 2.5 MIN AT LIGHTS OFF LIGHTS ON Occupants Room Sensor
TIME DELAY A 1% LEVEL Detected In Unoccupied Detects
LIGHT LEVEL
9 FT Mounting
H N H N H N
5.5 18
4.6 15
3.7 12
2.7 9
1.8 6 BLT Series
0.9 3
0m 0 ft
0.9 3 Simple as 1,2,3
1.8 6
2.7 9 1. Install the nLight® AIR fixtures with embedded smart sensor
3.7 12 2. Install the wireless battery-powered wall switch
4.6 15
5.5 18 3. With our CLAIRITY app, pair the fixtures with the wall switch and
if desired, customize the sensor settings for the intended outcome
rPODB 2P DX Mobile Device
2VTL2X4
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2011-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/09/17
RCR
800 5 74 61 52 60 51 44 58 50 44 0° - 180° 4394 100.0 100.0
45° 911 1037
1000 55° 706 865 6 69 55 46 54 45 39 52 44 38
65° 484 677 7 63 50 41 49 40 34 47 39 34
1200 40° 75° 254 466 8 59 45 36 44 36 30 43 36 30
1400 85° 55 153 9 55 41 33 41 33 27 40 32 27
0° 20° 90 4 10 10 52 38 30 38 30 25 37 30 25
0° 90°
2VTL2X4
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2011-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/09/17
Catalog
Number
Notes
2VTL
distribution. End plates include integral T-bar clips. Fixture may be mounted and wired in continuous rows.
Total fixture height is only 4-3/8".
OPTICS — Volumetric illumination is achieved by creating an optimal mix of light to walls, partitions, vertical
and horizontal work surfaces — rendering the interior space, objects and occupants in a more balanced,
complementary luminous environment. Linear faceted reflector cavity softens and distributes light into
the space while minimizing luminous contrast between the fixture and ceiling. Sloped end plates provide
a smooth, luminous transition between fixture and ceiling while enhancing the perception of fixture depth. 2' x 2'
High-performance diffuser provides LED concealment, even illumination across the diffuser and improved ADPT LED
lumen-per-watt performance.
Now available with two different aesthetics including the standard Acrylic Linear Prismatic Diffuser (ADP) and the Acrylic
Linear Prismatic Diffuser with Diffuser Trim Rings (ADPT).
ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality
of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000).
eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free,
low-current inrush, 89% efficiency and low EMI.
Optional integrated nLight®controls make each luminaire addressable - allowing it to digitally communicate
with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply
connect all the nLight enabled control devices and the VTLED luminaires using standard Cat-5 cabling. Unique
plug-and-play convenience as devices and luminaires automatically discover each other and self-commission.
Lumen Management: Unique lumen management system (option N80) provides on board intelligence that
actively manages the LED light source so that constant lumen output is maintained over the system life,
preventing the energy waste created by the traditional practice of over-lighting.
Step-level dimming option allows system to be switched to 50% power for compliance with common energy
codes while maintaining fixture appearance.
Driver disconnect provided where required to comply with US and Canadian codes.
SENSOR— Integrated sensor (individual control): Sensor Switch MSD7ADCX (Passive infrared (PIR))
or MSDPDT7ADCX (PIR/Microphonics Dual Tech (PDT)) integrated occupancy sensor/automatic dimming Dimensions
photocell allows the luminaire to power off when the space is unoccupied or enough ambient light is entering All dimensions are inches (centimeters) unless otherwise specified.
the space. See page 2 for more details on the integrated sensor.
Integrated Sensor (nLight Wired Networking): This sensor is nLight-enabled, meaning it has the ability
to communicate over an nLight network. When wired, using CAT-5 cabling, with other nLight-enabled Specifications
sensors, power packs, or WallPods, an nLight control zone is created. Once linked to a Gateway, directly or
via a Bridge, the zone becomes capable of remote status monitoring and control via SensorView software. Length: 24 (61.0) 4-3/8
See page 2 for the nLight sensor options. (11.1)
Width: 24 (61.0)
Integrated Smart Sensor (nLight Air Wireless Platform): The rES7 sensor is nLight AIR enabled, meaning
it has the ability to communicate over the wireless nLight control platform. It is both a digital PIR occupancy Depth: 4-3/8 (11.1) 8-1/4
(21)
sensor/automatic dimming photocell. It pairs to other luminaires and wall switches through our mobile 24
app, CLAIRITY, which allows for simple sensor adjustment. See page 3 for more details on the Integrated (61.0)
Smart Sensor.
INSTALLATION — Unique grid interfacing arrangement provides mounting into standard 1" and 9/16"
tee bar or screw slot grids. 9/16" allows fixture trim to hang level with architectural ceiling tiles. Drywall
ceiling adaptors available. Suitable for damp location.
LISTINGS — CSA Certified to meet U.S. and Canadian standards. IC rated. DesignLights Consortium® (DLC)
qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified
Products List at www.designlights.org/QPL to confirm which versions are qualified.
WARRANTY — 5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
NOTE: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specifications subject to change without notice.
Capable Luminaire
This item is an A+ capable luminaire, which has been designed and tested
to provide consistent color appearance and out-of-the-box control compatibility
with simple commissioning.
• All configurations of this luminaire meet the Acuity Brands’ specification for
chromatic consistency
• This luminaire is part of an A+ Certified solution for nLight® or XPoint™ Wireless
control networks when ordered with drivers marked by a shaded background*
To learn more about A+, visit www.acuitybrands.com/aplus.
*See ordering tree for details
LED 2VTL2X2
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: 2VTL2 40L ADPT EZ1 LP840 MSD7ADCX
2VTL2
2VTL2 2X2 VTL (blank) Static 20L 2000 lumens ADP Acrylic linear prismatic (blank) MVOLT EZ1 eldoLED dims to 1%, 0-10V
H Heat removal 33L 3000 lumens ADPT Acrylic linear prismatic 347 347V2 EZB eldoLED dims to dark, 0-10V
40L 4000 lumens with diffuser trim rings EDB eldoLED DALI3
EXB eldoLED DMX/RDM3
SLD Step-level dimming3
EXA1 Dims to 1%, XPoint wireless enabled4
EXAB Dims to dark, XPoint Wireless enabled4
LP830 3000 K, 80 CRI (blank) No nLight® (blank) No sensor control EL7L 700 lumen battery
LP835 3500 K, 80 CRI N80 nLight® with 80% lumen nLight Wired Networking pack (non-CEC
management compliant)
LP840 4000 K, 80 CRI NES7 nLight® nES 7 PIR integral occupancy sensor7,10
N80EMG nLight® with 80% lumen EL14L 1400 lumen battery
LP850 5000 K, 80 CRI NESPDT7 nLight® nES PDT 7 dual technology integral occupancy control7,10 pack (non-CEC
management for use with
LP930 3000 K, 90 CRI generator supply EM power5 NES7ADCX nLight® nES 7 ADCX PIR integral occupancy sensor with automatic compliant)
LP935 3500 K, 90 CRI dimming photocell7,10 EL14LSD 1400 lumen battery
N100 nLight® without lumen
management NESPDT7ADCX nLight® nES 7 PDT 7 dual technology intergral occupancy sensor with pack with self-
LP940 4000 K, 90 CRI diagnostic testing
automatic dimming photocell7,10
LP950 5000 K, 90 CRI N100EMG nLight® without lumen feature (non-CEC
management for use with Individual Control compliant) 12
generator supply EM power5 MSD7ADCX PIR integral occupancy sensor with automatic dimming control E10WLCP EM Self-Diagnostic
NLTAIR nLight AIR enabled6 photocell3,7,11 battery pack, 10W
MSDPDT7ADCX PDT integral occupancy sensor with automatic dimming control Constant Power, CEC
photocell3,7,11 compliant
Xpoint Wireless CP Chicago plenum
XADS7 XPoint™ wireless controller and micro 360° PIR occupancy and
photocell sensor3,4,9
nLight Wireless Networking
RES7N nLight® AIR PIR integral occupancy sensor with automatic
dimming photocell for Networking Capabilities 7,10
nLight Wireless Zone
RES7Z nLight® AIR PIR integral occupancy sensor with automatic
dimming photocell for zone control 7,10
2VTL2X2
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2011-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/09/17
Sequence of Operation
MOTION NO MOTION MOTION
MAX
MIN
LIGHTS ON 17.5 MIN 2.5 MIN AT LIGHTS OFF LIGHTS ON
TIME DELAY A 1% LEVEL Occupants Room Sensor
Detected In Unoccupied Detects
LIGHT LEVEL
*The presetting on the automatic dimming photocell is 5fc. The Space Motion
height up to 15 ft (4.57 m) and *The presetting on the automatic dimming photocell is 5fc.
• 1.75x up to 20 ft (6.10 m).
• Provides 12 ft (3.66 m) radial detection of small motion when mounted at 9 ft (2.74 m)
• Initial detection will occur earlier when walking across sensor’s field of view than when
walking directly at sensor
9 FT Mounting
H N H N H N
5.5 18
4.6 15
3.7 12
2.7 9
1.8 6 BLT Series
0.9 3
0m 0 ft
0.9 3 Simple as 1,2,3
1.8 6
2.7 9 1. Install the nLight® AIR fixtures with embedded smart sensor
3.7 12 2. Install the wireless battery-powered wall switch
4.6 15
5.5 18 3. With our CLAIRITY app, pair the fixtures with the wall switch and
if desired, customize the sensor settings for the intended outcome
rPODB 2P DX Mobile Device
2VTL2X2
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2011-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/09/17
RCR
45° 470 550 5 75 61 52 60 51 45 58 50 44 0° - 180° 2287 100.0 100.0
500 55° 361 458 6 69 55 46 54 46 39 52 45 39
600 65° 246 358 7 64 50 41 49 41 35 48 40 34
40° 75° 128 238 8 59 46 37 45 37 31 43 36 31
700 85° 29 65 9 55 42 33 41 33 28 40 33 28
0° 20° 90 2 2 10 52 39 31 38 30 25 37 30 25
0° 90°
2VTL2X2
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2011-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/09/17
Luminaire Type:
Catalog Number
(autopopulated):
8” Evo®
Downlight
Solid-State Lighting
Series Color temperature Nominal lumen values Aperture/Trim color Distribution Finish Voltage
EVO 27/ 2700 K 20 2000 lumens 8AR Clear VND Very narrow (0.5 s/mh) LSS Semi-specular 120
30/ 3000 K 25 2500 lumens 8PR Pewter ND Narrow (0.7 s/mh) LD Matte-diffuse 277
35/ 3500 K 30 3000 lumens 8WTR Wheat MD Medium (0.9 s/mh) LS Specular 3472
40/ 4000 K 8GR Gold MWD Medium wide (1.0 s/mh)
8WR1 White WD Wide (1.2 s/mh)
8BR1 Black
8WRAMF1 White anti-
microbial
Driver3 Options
EZ10 eldoLED 0-10V ECOdrive. Linear dimming to 10% min. SF5 Single fuse. BGTD Bodine generator transfer device.
EZ1 eldoLED 0-10V ECOdrive. Linear dimming to 1% min. TRW6 White painted flange Specify 120V or 277V.
EZB eldoLED 0-10V SOLOdrive. Logarithmic dimming to <1%. TRBL7 Black painted flange CRI90 High CRI (90+)
EDAB eldoLED SOLOdrive DALI. Logarithmic dimming to <1%. EL8 Emergency battery pack with CP11 Chicago plenum. Specify 120V or 277V.
EDXB eldoLED POWERdrive DMX with RDM (remote device manage- integral test switch RRL__ RELOC®-ready luminaire connectors
ment). Square Law dimming to <1%. Includes termination ELR8 Emergency battery pack with enable a simple and consistent factory
resistor. Refer to DMXR Manual. remote test switch installed option across all ABL luminaire
EXA1 XPoint Wireless, eldoLED 0-10V ECOdrive. Linear dimming to NPS80EZ5 nLight® dimming pack controls brands. Refer to RRL for complete
1%. Refer to XPoint tech sheet. 0-10V eldoLED drivers. nomenclature.
EXAB XPoint Wireless, eldoLED 0-10V SOLOdrive. Logarithmic NPS80EZER5,9 nLight® dimming pack controls
dimming to <1%. Refer to XPoint tech sheet. 0-10V eldoLED drivers. ER
ECOS24,5 Lutron® Hi-Lume® 2-wire forward-phase driver.120V only. controls fixtures on emergency
Minimum dimming level 1%. circuit.
ECOS34,5 Lutron® Hi-Lume® 3-wire or EcoSystem dimming driver. N8010 nLight® Lumen Compensation
Minimum dimming level 1%.
8” EVO
Downlight
Solid-State Lighting
85
8 [22.0]
15 7
8 [40.3]
3 [36.0]
14 16
ORDERING NOTES
1. Not available with finishes. 7. Not available with black reflector
2. Not available with EL or ELR options. 8. For dimensional changes, refer to TECH-140. Not available with 347V.
3. Refer to TECH-240 for compatible dimmers. 9. For use with generator supply EM power. Will require an emergency hot feed and normal hot feed.
4. Not available with nLight® and XPoint options. 10. Fixture begins at 80% light level. Must be specified with NPS80EZ or NPS80EZER.
5. Specify voltage. 11. ELR not available.
6. Not available with white reflector.
8” EVO
Downlight
Solid-State Lighting
Distribution Curve Distribution Data Output Data Coefficient of Utilization Illuminance: Single Luminaire 30” Above Floor
LUMEN OUTPUT MULTIPLIER - CRI LUMEN OUTPUT MULTIPLIER - CCT LUMEN OUTPUT MULTIPLIER - TRIM FINISH
CRI FACTOR CRI FACTOR CLEAR PEWTER WHEAT GOLD WHITE BLACK
FINISH (AR) (PR) (WTR) (GR) (WR/WRAMF) (BR)
80 CRI 1 4000 K 1.035
Specular (LS) 1.00 0.88 0.83 0.95 N/A N/A
90 CRI 0.79 3500 K 1
Semi-specular (LSS) 0.95 0.84 0.79 0.90 N/A N/A
3000 K 0.973
Matte-diffuse (LD) 0.85 0.73 0.69 0.80 N/A N/A
2700 K 0.938
Paint N/A N/A N/A N/A 0.87 0.73
PHOTOMETRY NOTES
• Tested in accordance with IESNA LM-79-08.
• Tested to current IES and NEMA standards under stabilized laboratory conditions.
• CRI: 85 typical.
8” EVO
Downlight
Solid-State Lighting
A B
C
nPS 80 EZ
A
B B
C
Push-Button WallPod
Traditional tactile buttons Graphic WallPod nPS 80 EZ
and LED user feedback Full color touch screen
provides a sophisticated WIRING KEY
look and feel A B C OPTIONAL
Low Voltage A
CAT-5e Cable Line Power
Dimming Wires nCM ADCX
EXAMPLE
Group Fixture Control*
*Application diagram applies for fixtures with eldoLED drivers only.
Capable Luminaire
This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and
out-of-the-box control compatibility with simple commissioning.
• All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency
• This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a
shaded background*
• This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality
at the luminaire level, when selection includes driver and control options marked by a shaded background*
To learn more about A+, visit www.acuitybrands.com/aplus.
*See ordering tree for details
Catalog
Number
Notes
LED WL4LED
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: WL4 30L EZ1 LP840
WL4
Series Lumens1 Voltage Driver Color temperature Controls
WL4 4' wall-mount LED 20L 2000 lumens (blank) MVOLT EZ1 eldoLED dims to 1%, 0-10V LP830 3000 K (blank) No nLight
30L 3000 lumens 347 347V EZB eldoLED dims to dark, 0-10V LP835 3500 K N80 nLight® with 80% lumen
40L 4000 lumens LP840 4000 K management
LP850 5000 K N80EMG nLight® with 80% lumen
management for use with
generator supply EM power2
N100 nLight® without lumen
management
N100EMG nLight® without lumen
management for use with
generator supply EM power2
NLTAIR nLight AIR enabled3
(blank) No sensor control (blank) Fixture turns off when unoccupied EL7L LED Emergency battery pack (blank) White
nLight Wired Networking DIM10 Fixture dims to approximately 10% (nominal 700 lumens); see Life
light output when unoccupied Safety section9
NES7 nLight® nES 7 PIR integral occupancy sensor5
DIM50 Fixture dims to approximately 50% EL14L LED Emergency battery pack
NESPDT7 nLight® nES PDT 7 dual technology integral occupancy control 5 (nominal 1400 lumens); see Life
light output when unoccupied
NES7ADCX nLight® nES 7 ADCX PIR integral occupancy sensor with Safety section9
automatic dimming photocell5 SC Surface conduit end cap provisions
Individual Control
MSD7 Sensor Switch® MSD 7 PIR Integral Occupancy Control6
Xpoint Wireless
XADS7 XPoint™wireless controller and micro 360° PIR occupancy and
photocell sensor7
XADNS7 XPoint™å wireless controller and micro 360° PIR occupancy and
photocell sensor (egress lighting)7
nLight Wireless Networking
RES7N nLight® AIR PIR integral occupancy sensor with automatic
dimming photocell for Networking Capabilities
nLight Wireless Zone
RES7Z nLight® AIR PIR integral occupancy sensor with automatic
dimming photocell for zone control
Notes
1 Approximate lumen output.
2 nLight EMG option requires a connectio nto existing nLight network. Power is provided
from a separate N80 or N100 enabled fixture
3 Must order with RES7N or RES7Z sensor. Only availble with EZ1 driver.
4 See sensor options on page 3.
5 Requires N80, N100, N80EMG, or N100EMG. Cannot be ordered with EZB and EL7L or
EL14L together.
6 Not available with nLight options or EZB.
7 Not available with nLight options or Standyby Mode. Gateway not included. Requires
on-site commissioning. Visit www.lightingcontrols.com/XPointWireless for more
information.
8 Requires Occupancy Control.
9 Not available with 347V. Cannot be ordered with 40L, EZB, and sensor combination.
10 For additional paint finishes, refer to Architectural Colors.
WL4LED
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/05/17
WL4LED
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/05/17
Sequence of Operation
MOTION NO MOTION MOTION
MAX
MIN
LIGHTS ON 17.5 MIN 2.5 MIN AT LIGHTS OFF LIGHTS ON Occupants Room Sensor
Detected In Unoccupied Detects
LIGHT LEVEL
9 FT Mounting H H H
N N N
5.5 18
4.6 15
3.7 12
2.7 9
1.8 6
0.9 3 Simple as 1,2,3
0m 0 ft
0.9 3 1. Install the nLight® AIR fixtures with embedded smart sensor
1.8 6 2. Install the wireless battery-powered wall switch
2.7 9
3.7 12 3. With CLAIRITY app, pair the fixtures with the wall switch and if
4.6 15 desired, customize the sensor settings for the desired outcome
5.5 18
WL4LED
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/05/17
PHOTOMETRICS
WL4 30L EZ1 LP840, 3250.8 delivered lumens, test no. LTL25482P5, tested in accordance to IESNA LM-79
180°
Coefficients of Utilization
pf 20%
90°
CP Summary pc 80% 70% 50% Zonal Lumen Summary
80° 0° 90 pw 70%50%30% 50%30%10% 50%30%10% Zone Lumens % Lamp % Fixture
100
0° 912 912 0 116 116 116 112 112 112 104 104 104 0° - 30° 701 21.6 21.6
200 5° 901 910 1 104 99 94 95 91 87 88 85 81 0° - 40° 1143 35.2 35.2
300 15° 856 879 2 94 85 78 82 75 70 76 71 66 0° - 60° 2032 62.5 62.5
60°
400 25° 777 823 3 85 74 66 72 64 57 67 60 55 0° - 90° 2829 87.0 87.0
35° 666 745 4 78 66 56 63 55 48 59 52 46 90° - 120° 256 7.9 7.9
500
RCR
MOUNTING DATA
For unit installation; surface ceiling or wall mounting.
46
1 (116.8)
(2.5)
1-5/8
(4.1) 3-3/8
(8.1)
1-3/8 17-3/4
(3.5) (45.1)
WL4LED
LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2016-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 09/05/17
SPECIFICATIONS
Project:
HIGHLIGHTS
3 1 ⁄ 2” LUMEN PACKAGES
Option:
Flat end cap Sculptured end cap DISTRIBUTION
100% Down
COMPANION LUMINAIRE(S)
CUSTOMIZATION
PeerlessLighting.com
© 2014-2017 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting. Products and technologies 510.845.2760ꢀ|ꢀTechSupport@PeerlessLighting.com
in this document may be covered by one or more U.S. Patents and Patents Pending. NOTE: Specifications subject to change without notice. Rev. 09/05/17 1
Type:
SPECIFICATIONS
MODEL NUMBERꢀExample:ꢂSQWS LLP 16FT MSL8 80CRI 35K 800LMF DARK ZT 120 SCT F1/24A C110
t t t t t t
Luminaire Linear Length Plan Total Run Length Maximum Section Length LED Color Rendering LED Color Temperature
SQWS LLP Linear longest possible __FT 4FT MSL4 4' Section(s) 80CRI 80+ CRI 30K 3000K
LSL Longest same length Indicate Luminaire Row Length MSL8 8' Section(s) 35K 3500K
in 4’ increments. Ex: 12FT 40K 4000K
t t t t t
Direct LED Output Minimum Dimming Level Control Input Voltage Wiring Option
400LMF 400 nominal direct lumens per foot DARK Constant current, dimming to < 1% ZT* 0-10V 120 120V SCT Single circuit
800LMF 800 nominal direct lumens per foot DALI** DALI 277 277V
*0-10V will use linear
dimming curve
** Will use logarithmic
dimming curve
t t
Emergency Options Color Options
(Blank) None C032 Gloss white CSA Manufactured to Canadian Standards
1EC (1) Emergency circuit module C100 Anodized aluminum CP Chicago Plenum (available with F1A only)
2EC (2) Emergency circuit module C110 Painted aluminum ELH* Emergency through wiring w/single feed, shared neutral
__EC ___ Emergency circuit modules C201 Black (low gloss) ELS2* Emergency through wiring w/single feed, seperate neutrals
Emergency type is installed in last 4’ of luminaire C099 Custom color GLR Fast blow
sections. Separate feed required.
GMF Slow blow
SCEP Sculptured end cap
*Not available with CSA
PeerlessLighting.com
© 2014-2017 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting. Products and technologies 510.845.2760ꢀ|ꢀTechSupport@PeerlessLighting.com
in this document may be covered by one or more U.S. Patents and Patents Pending. NOTE: Specifications subject to change without notice. Rev. 09/05/17 2
Type:
PHOTOMETRICS
6’-8”
8’ Section
34 LBS
8’-2” O.A.
ELEVATION
LINEAR PLAN:
PEERLESS offers the ability to provide a continuous run plan to suit your requirements by optionally offering three different methods of configuration.
LLP 8 FT 8 FT 4FT
PeerlessLighting.com
© 2014-2017 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting. Products and technologies 510.845.2760ꢀ|ꢀTechSupport@PeerlessLighting.com
in this document may be covered by one or more U.S. Patents and Patents Pending. NOTE: Specifications subject to change without notice. Rev. 09/05/17 3
Type:
MOUNTING DETAIL
3 1 ⁄2 ”
3 1 ⁄4”
Wall Bracket
1
⁄2 ”
Mounting holes
for #10 screw
Mounting holes to luminaire
PeerlessLighting.com/eldoLED-compatibility
PeerlessLighting.com
© 2014-2017 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting. Products and technologies 510.845.2760ꢀ|ꢀTechSupport@PeerlessLighting.com
in this document may be covered by one or more U.S. Patents and Patents Pending. NOTE: Specifications subject to change without notice. Rev. 09/05/17 4
Catalog
Number
Notes
FEATURES & SPECIFICATIONS
INTENDED USE — Sharing many popular Z Series elements, this solid-state strip offers long main- Type
tenance-free life, several color temperatures, lumen outputs and lengths. Ideal for new construction
and retrofit applications in T5 and T8 lengths. Ideal for uplight and downlight in commercial, retail,
manufacturing, warehouse, cove and display applications.
CONSTRUCTION — Compact-design channel and cover are formed from code-gauge, cold-rolled steel. Lensed LED Striplight
Improved easy "snap 'n' lock" end plates allow for quick attachment.
ZL2N
Finish: Paint options include high-gloss, baked white enamel (WH), galvanized (GALV), matte black
(MB) and smoke gray (SKGY). Five-stage iron phosphate pre-treatment ensures superior paint adhesion
and rust resistance.
OPTICS — Replaceable medium diffuse lens (up to 10%) offer ingress protection from debris.
ELECTRICAL — Utilizes high-output LEDs integrated on a two-layer circuit board, ensuring cool-running
operation. Internal pluggable wiring harness prevents wiring errors. Electronic LED driver is rated for 75
input watts maximum (see Operational Data on page two for actual wattage consumption), multi-volt 24" and 48" Lengths
input and 0-10V dimming standard. This fixture is designed to withstand a maximum line surge of
1.5kV at 0.75kA combination wave for indoor locations, for applications requiring higher level of protec-
tion additional surge protection must be provided.
LEDs provide 83 CRI at 3000 K, 3500 K,4000 K or 5000 K.
Lumen output ranges from 2100 to 6000 lumens. Beam angle is 110 FWHM (full width at half maximum).
Lumen output up to 1,300 lumens per foot. In 86°F (30°C) ambient environments, L70 is predicted to
be 100,000+ hours, L85 at 44,000 hours. Luminaire should be installed in applications where ambient
temperatures do not exceed 86°F (30°C). Ambient temperatures that exceed 86°F (30°C) will result in
reduced life and will void warranty.
INSTALLATION — Tool-less channel cover for easy installation.
Fixture may be surface, pendant or stem mounted. Three-point aligner locks in place for easy continuous
row mounting.
LISTINGS — UL Listed. CSA certified to US and Canadian safety standards. For use in damp locations
between -4°F (-20°C) and 86°F (30°C).
WARRANTY — 5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specifications subject to change without notice.
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: ZL2N L48 3000LM MDD MVOLT 40K 80CRI WH
ZL2N
Series Length Nominal lumens1 Diffuser Voltage
ZL2N Lensed LED striplight L24 24" 2000LM 2,000 lumens MDD Medium diffuse MVOLT 120-277V 277 277V
L46 46" 2000LM 2,000 lumens ZSD Zebra striped lens 120 120V 347 3472
L48 48" 3000LM 3,000 lumens 208 208V 480 4802
5000LM 5,000 lumens 240 240V
Notes
1 See Operational Data on page 2 for actual lumens.
Accessories: Order as separate catalog number. Replacement Lens
2 Not available with L24, 24" fixture. 347V and 480V utilize a step-down transformer.
ZACVH Aircraft cable with hook LZL2 XX MDIF Medium-diffuse lens. Specify length 3 See ordering information on page 3.
HC36 Hanger chain, 36" 24 or 48 (example: LZL2 24 MDIF)9 4 Not available with cordsets.
ZSPRG For 15/16" T-grid only 5 Use ZSPRG for surface mounting when order this option.
LSXR Sensor Switch® LSXR occupancy sensor3 6 Specify voltage, 120 or 277.
7 Output is 1400 lumens.
8 Cordsets exit back of fixture unless OUTEND option is specified.
9 XX denotes length.
INDUSTRIAL ZL2N
Page 1 of 4
48-1/8
1-3/8 (122.2) 1-3/8
(3.6) (3.6)
24-1/8
1-3/8 (61.3) 1-3/8 1-1/4
(3.6) (3.6) (3.0)
3-1/2
(8.9)
PHOTOMETRICS
Please see www.lithonia.com.
INDUSTRIAL ZL2N
Page 2 of 4
PLR
variety of architectural products mounted in continuous rows. 1, 2, 3 and 4-lamp fixtures. PLR22 (2-cir-
cuit) and PLR33 (3-circuit) crossover harness switches hot circuit serving next fixture in row. Reduces
fixture types on job for alternating circuit applications (see example below.)
Easy one-step installation, saves up to 35% on labor costs. Expanded switching flexibility helps save energy.
Rows can be 50% longer with two-circuit systems. Polarized, lock-together nylon connectors prevent
miswiring in the field. #12 THHN conductor, rated 600V, 90°C. White neutral wire included. Grounding Advanced 3-Circuit Plug-In
accomplished by fixture in-row connectors.
CSA certified systems available with up to 2 circuits. G ground required.
Note: Specifications subject to change without notice.
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative.
LSXR
also elapsed) if no occupancy is detected.
This timer is factory set at 10 minutes to promote energy savings, but is adjustable between 30 seconds
and 30 minutes. These adjustments may be done through the unit’s push-button.
FEATURES
• Four interchangeable lenses - high mount 360°, low mount 360°, high mount aisleway, and small
motion 360°. Single Relay
• Integrated mounting bracket drops lens down 3" from chase nipple - no bracket accessory required.
• 100% digital PIR detection - provides excellent RF immunity
Note: Specifications subject to change without notice.
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: LSXR 10 ADC HVOLT 30M
LSXR
Series Lens option Dimming/photocell
LSXR Passive Infrared Indoor (blank) No lens 610 High and low mount 360° (blank) None
Occupancy Sensor 6 High mount, 360® 650 High mount 360° and aisleway HL High/low occupancy operation
10 Low mount, 360° 3PK High and low mount 360° and aisleway P Switching photocell (on/off)
50 High mount aisleway 4PK All lenses ADC Dimming and switching photocell
9 Small motion, 360° ANL Dimming and switching photocell with
high/low occupancy operation
Voltage Max dim level Min dim level Lead length Temp humidity Default time delay
(blank) 120-277 VAC (blank) 10 VDC (blank) Minimum dimming level of ballast (blank) 14" (blank) None (blank) 10 minutes (with minimum
(MVOLT) 9H 9 VDC 1V 1 VDC 42L 42" LT Low temperature 15 minutes on time)
HVOLT 347-480 VAC 8H 8 VDC 2V 2 VDC 5M 5 minutes (LED only)
7H 7 VDC 3V 3 VDC 15M 15 minutes
4V 4 VDC 20M 20 minutes
5V 5 VDC 30M 30 minutes
6V 6 VDC
INDUSTRIAL ZL2N
Page 3 of 4
ZACVH HANGER
10' Aircraft cable with Y hanger.
Order as:
ZACVH
ZL2N
INDUSTRIAL: One Lithonia Way, Conyers, GA 30012 Phone: 800-315-4963 Fax: 770-981-8191 www.lithonia.com © 2013-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 06/29/17
Page 4 of 4
Catalog
Number
Notes
FEATURES & SPECIFICATIONS
INTENDED USE — Suitable for architectural applications where aesthetics and superior performance
are required. Type
CONSTRUCTION — High-polish, injection-molded virgin acrylic panel, ultrasonically welded to eliminate
visible hardware. Graduated depth of molded letters provides uniform light distribution on graphics.
Standard housing finish is brushed aluminum.
Precision-molded, textured letters – 6” high with 3/4” stroke, with 100 ft viewing distance rating, based
upon UL924 standard. Chevron indicator direction must be specified.
Recessed rough-in section constructed of 20-gauge, die-formed galvanized steel. Extruded aluminum
housing trim mounts flush onto wall or ceiling.
Edge-Lit Exits
Mounting canopy for top mount is constructed of extruded aluminum housing to match housing finish.
ELECTRICAL — Sealed, maintenance-free nickel cadmium battery delivers 90 minutes capacity to lamp.
Constant-current series charger, 24-hour recharge after 90-minute discharge.
Polarized battery connector simplifies installation and maintenance; prevents charger damage due to
improper connection.
LRP
OPTICS — LEDs mounted on printed circuit board. The typical life of the exit LED lamp is 10 years.
Low energy consumption – EL N operation: only 2.3W for 120V single-face red sign; 1.7W for 120V LED LAMPS
single-face green sign. Non-emergency operation: only 1.5W for 120V single-face red sign; 1.2W for 120V
single-face green sign.
INSTALLATION — Recessed mount – rough-in section for back, ceiling or end mounting. Fits into minimum
wall or ceiling opening 13-5/8” L x 4-1/2” W x 3-1/8” D.
Adjustable T-bar hangers adapt mounting tray for mounting in suspended ceilings or variable-size framed
openings. Trim ring has 3/4” variable depth adjustment to ensure flush fit against surface of wall or ceiling.
Plug-in wire connections and self-captive mounting screws for mounting panel/trim to rough-in section. WARRANTY — 5-year limited warranty, including lamps. Complete warranty terms located at:
Top Mount (TM) - low-profile mounting canopy attaches exit to J-box. No rough-in section required. www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
LISTINGS — UL listed. Non-IC recessed mounting. Meets UL 924, NFPA 101 (current Life Safety Code), NOTE: Actual performance may differ as a result of end-user environment and application.
NEC and OSHA illumination standards, and State of Minnesota requirements for less than 20W energy All values are design or typical values, measured under laboratory conditions at 25°C.
consumption. Listed and labeled to comply with Canadian Standards C-860 and C-22.2 No.9 (see options). Specifications subject to change without notice.
NEMA Premium certified.
ORDERING INFORMATION For shortest lead times, configure products using bolded options. Example: LRP 1 RMR LA 120/277 EL N
LRP
Family Housing color Number of faces Letters/background Directional indicators2 Input voltage
LRP LED (blank) Brushed aluminum 1 Single face RW Red on white (blank) None 120/277 Dual voltage
W White 2 Double face RC Red on clear (single face only)2,3 LA Left3 120/347 Dual voltage5
B Black RMR Red on mirror (simulates clear background RA Right3
BZ Bronze Specify for double-face exits)2,4 LRA Left and right
BS Polished Brass1 GW Green on white DA Double face4
U Unfinished GC Green on clear (single face only)2,3
GMR Green on mirror (simulates clear background Specify
for double-face exits)2,4
EMERGENCY LRP
ELECTRICAL AC ONLY 2
(5.1)
Primary Circuit 14-3/4
8
(37.5)
(20.3) 3-1/8
Typical Supply Number of Input Max. (7.9)
Type LED life1 voltage faces watts amps 13-1/2 4-1/2 13-5/8
(11.4) (34.6)
120 1 1.5 .087 (34.3)
Red 10 years 277 1 1.8 .089 End Mount (recessed) Rough -In Section
347 1 2.2 .107
120 2 3.1 .178 5-1/4
(13.3)
Red 10 years 277 2 3.4 .180
347 2 4.1 .220 4-1/4
120 1 1.2 .064 (10.8)
Green 10 years
277 1 1.3 .062
120 2 2.0 .06
Green 10 years
277 2 2.3 .06
Silk-screening process allows customized text and/ Unique wedge-shaped panel design concentrates Trim fits flush against wall or ceiling for clean, Small rough-in section.
or graphics. light for uniform letter illumination. attractive appearance.
LRP
EMERGENCY: One Lithonia Way Conyers, GA 30012 Phone: 800.334.8694 www.lithonia.com © 1994-2017 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/01/17