Professional Documents
Culture Documents
To the Customer
The part numbers in this parts catalog were correct at the time your catalog was published. It is our policy to constantly improve our machines,
and therefore, part numbers may change. When ordering parts, verify part numbers through your dealer.
SI Units of Measure
Metric dimensions are given, where applicable, throughout this parts catalog.
Direction Arrow
Arrows are used with illustrations to indicate the front of the unit. “Right-Hand” and “Left-Hand” sides are determined by facing in direction of ma-
chine forward travel.
Box-enclosed Illustrations
A key number, shown in the parts list, is assigned to a box enclosing all parts sold as a service assembly. A box not keyed includes non-current
parts.
Orientation of Engine
“Right Hand” and “Left Hand” sides are determined by standing at the flywheel and facing the engine.
544G
1st Line Designates
1 — Two Letters For Engine Factory Designation T-John Deere Dubuque Works
2 — One Digit For Number Of Cylinders And Three Digits For 6059 (5.9 Liter)
Displacement In Liters
3— One Letter For Aspiration Type T-Turbocharged
4— Six Digits For Engine Serial Number 123456
2nd Line Designates
5 — Engine Application 6059TDW05 (544G) (Engine Serial No. -512384)
6059TDW08 (544G) (Engine Serial No. 512385- )
6059TDW07 (544GH)
624G
1st Line Designates
1 — Two Letters For Engine Factory Designation T-John Deere Dubuque Works
2 — One Digit For Number Of Cylinders And Three Digits For 6068 (6.8 Liter)
Displacement In Liters
3— One Letter For Aspiration Type T-Turbocharged
4— Six Digits For Engine Serial Number 123456
2nd Line Designates
5 — Engine Application 6068TDW09 (624G)
6068TDW10 (624GH)
4 - 1700 MM (66.9")
5 - 1700 MM (66.9")
6 - 1953 MM (76.9")
7 - 1953 MM (76.9")
A - Special, 710C Axle Housing And Shaft
B - Special, LH Offset (1627 MM)
C - Special, RH Offset (1627 MM)
D - Special, LH Offset (1500 MM)
E - Special, RH Offset (1500 MM)
1 - Standard Input Housing, No Auxiliary Brake 12. Input Housing And Auxiliary Brake
3 - Special With Manual Brake
5 - Special With SAHR Brake
A - Special, Disconnect
1 - Fixed Mounting 13. Mounting Type
2 - Oscillation, Center Pivot, Front Bracket
A - Special, Offset Support Mounting
1 - No Brakes 14. Brake Type
2 - Standard Capacity - Independent Brakes
3 - Standard Capacity - Dual Brakes
4 - High Capacity - Independent Brakes
5 - High Capacity - Dual Brakes
1 - Standard 15. Differential Type
2 - No-Spin
3 - Hydraulic Lock-Capture System
1 - Standard 16. Differential Case
2 - Low Profile
1 - None 17. Final Drive Reduction
2 - 3.714:1
3 - 4.800:1
4 - 5.500:1
5 - 6.000:1
B - Fixed
1 - Nothing (Interfactory) 18. Trim
2 - VCI Bag
3 - Primer
1 - Miscellaneous Parts (Interfactory) 19. Miscellaneous Parts
2 - Miscellaneous Parts
Trademarks
Throughout this parts catalog, you may find the following Deere and Company trademarks:
Best Bid™ CounterParts™ DEERE™ (Deere™)
Dura-Trax™ Fanggs™ Guardian™
HTH™ Jagz™ JDLink™
MARKS™ MIC™ [Machine Information Center] MTH™
Power Curve™ Powerllel™ PowerShift Plus™
Powerwize™ POWR SAVR™ PowrShift™
ProPath™ Quad-Cool™ Quik-Tatch™
SC-2™ Side-Tracker™ Stinger™
StructureALL™ Swamper™ TMC™ [Total Machine Control]
ValueSelect™ Waratah™ Worksite Pro™
FlexBox™ Funk™ iTorque™
Phoenix™ Phoenix International™ PowerTech™
PowerTech™ E PowerTech™ M PowerTech™ Plus
Precision Joint™ SHIFT-O-MATIC™ SWEDA™ (Super Wide Extreme Dual Axle)
TeamMate™ TeamMate™II TeamMate™ IV
TMII™ TMIII™