Professional Documents
Culture Documents
21FK2RGX-T4 Manual de Servicio Chasis CW81B PDF
21FK2RGX-T4 Manual de Servicio Chasis CW81B PDF
COLOR TV
SERVICE MANUAL
CHASSIS : CW81B
MODEL : 21FK2RL/RG/RGX/RLX/
RLD/RGUL
MODEL : 21FK2RL/RG/RGX/RLX/
RLD/RGUL-T4/Z4
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Jan., 2009
P/NO : MFL42115606 Printed in China
CONTENTS
CONTENTS ............................................................................................... 2
SAFETY PRECAUTIONS...........................................................................3
SPECIFICATIONS ......................................................................................4
ADJUSTMENT ...........................................................................................6
Copyright©2009 LG Electronics.Inc. All right reserved. -2- LGE Internal Use Only
Only for training and service purposes.
SAFETY PRECAUTIONS
An isolation Transformer should always be used during the always perform an AC leakage current check on the exposed
servicing of a receiver whose chassis is not isolated from the AC metallic parts of the cabinet, such as antennas, terminals, etc., to
power line. Use a transformer of adequate power rating as this be sure the set is safe to operate without damage of electrical
protects the technician from accidents resulting in personal injury shock.
from electrical shocks.
Leakage Current Cold Check(Antenna Cold Check)
It will also protect the receiver and it's components from being With the instrument AC plug removed from AC source, connect an
damaged by accidental shorts of the circuitry that may be electrical jumper across the two AC plug prongs. Place the AC
inadvertently introduced during the service operation. switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
If any fuse (or Fusible Resistor) in this TV receiver is blown, each exposed metallic parts such as antenna terminals, phone
replace it with the specified. jacks, etc.
If the exposed metallic part has a return path to the chassis, the
When replacing a high wattage resistor (Oxide Metal Film Resistor, measured resistance should be between 1MΩ and 5.2MΩ.
over 1W), keep the resistor 10mm away from PCB. When the exposed metal has no return path to the chassis the
reading must be infinite.
Keep wires away from high voltage or high temperature parts. An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube. Do Leakage Current Hot Check (See below Figure)
not lift the Picture tube by it's Neck. Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
X-RAY Radiation Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
Warning: and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
The source of X-RAY RADIATION in this TV receiver is the High with 1000 ohms/volt or more sensitivity.
Voltage Section and the Picture Tube. Reverse plug the AC cord into the AC outlet and repeat AC voltage
For continued X-RAY RADIATION protection, the replacement measurements for each exposed metallic part. Any voltage
tube must be the same type tube as specified in the measured must not exceed 0.75 volt RMS which is corresponds to
Replacement Parts List. 0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
To determine the presence of high voltage, use an accurate high
impedance HV meter. Leakage Current Hot Check circuit
1.5 Kohm/10W
Copyright©2009 LG Electronics.Inc. All right reserved. -3- LGE Internal Use Only
Only for training and service purposes.
SPECIFICATIONS
Note : Specification and others are subject to change without notice for improvement.
General specification
Copyright©2009 LG Electronics.Inc. All right reserved. -4- LGE Internal Use Only
Only for training and service purposes.
Features and Function (For China. Indonesia, Vietnam, Thai, CIS / Middle East Asia, Africa)
6 Timer Clock -- : --
Off time -- : -- Off(On)
On time -- : -- Pr 1 VOL 30 Off (On)
Auto off On/ Off
7 Special Language English/ Indonesia/ Thai/ Vietnam East Asia
Input TV/ AV/ Component
Child lock On/ Off
Etc. Sleep
8 Review
Copyright©2009 LG Electronics.Inc. All right reserved. -5- LGE Internal Use Only
Only for training and service purposes.
ADJUSTMENT
1. Scope of Application 4. Screen Voltage Adjustment
These instructions are applied to CW81B Chassis.
4-1. Adjustment (Using Factory Remote Control)
1) Input in the 75Ω cable LG standard signal (Digital Pattern,
2. Notes 480NC).
1) Because this is a cold chassis, it is not necessary to use an 2) Press the “ADJ’ key of factory remote control once to make
isolation transformer. However, operating it using a the TV set display horizontal line.
transformer between the power supply line and chassis input 3) Turn the screen volume on the FBT clockwise until the
to prevent electric shock and to protect the test instrument. horizontal line is visible and turn it counterclockwise until
2) All adjustment must be done in the correct sequence. horizontal line faintly visible.
However, for better productivity, it can be change in a pre- (Exit screen voltage adjustment by press “Enter(A)” key of
permitted range. factory remote control.)
3) Environment conditions : If not specified, it must be done in
following conditions.
Temperature : 25 ± 5°C 5. Purity and Convergence Adjustment
Humidity: 65% ± 10%
4) Power supply of SET for PAL/SECAM 5-1. Purity adjustment
China/indonesia/Vietnam/CIS Market: AC100~240V±10%,
50/60Hz. (1) Adjustment Preparation
5) If not specified, the receiver must be operated for more than 1) Receive Red Raster Pattern for purity adjustment (51CH).
20 minutes prior to the adjustment. 2) Demagnetize the CPT and Cabinet with a degaussing coil.
6) Signal : Received the standard color signal (65dB±1dBuV).
PAL/SECAM: LG standard signal means the digital pattern (2) Adjustment
PAL-B/G 05CH. 1) Pre-adjust the static convergence (STC) with the 4 and
7) If not specified, APC ON is APC CLEAR (DYNAMIC) 6pole magnet.
2) If the horizontal Line is inline with CPT Mark, 2-Pole
magnet should direct 3-9 o’clock direction.
3. AGC Voltage Adjustment 3) If not, direct 2-pole magnet handle toward 6-12 o’clock
direction and adjust the Horizontal Line to fall onto the
3-1. Necessary Instrument mark opening the magnet at an angle.
- Digital Multi-meter: 1 set 4) Push the DY(deflection yoke) all the way to the CPT
- Max Input Current : Over 1A/ Max Input Voltage : 500Vdc funnel.
- Measurement Range : 10mV-100mVdc/ Accuracy : 0.03% 5) Turn the purity magnet(2-pole magnet) so that the “green”
color portion of left side and the “blue” color portion on the
3-2. Adjustment Preparation right side have equal amount of color.
1) Input in the 75Ω cable 65dB(±1dB) LG standard signal.
2) Connect the multi-meter to J105 (AGC Check, Marking). G R B G R B
3-3. Adjustment 6) Pull the DY slowly backward and fix it when the whole
1) Press the “INSTART” key of factory remote control and screen becomes red.
select “VP0 (RF AGC)” adjustment mode. (The specified torque for fixing DY screw should be
2) Press the VOL+/- (F/ G) key until the multi-meter shows 10Kg/cm.)
reading as shown below.
3) CAUTION: Since the signal strength can be easily G R B R
changed by the condition of signal cable, you need to
check the signal strength frequently in order to prevent
error. 5-2. Convergency Adjustment
Tuner P/N Maker AGC Vol Signal Tuner Spec. Remark (1) Necessary Instrument
6700NFNS11E LGIT 2.15 ± 0.05V 65dBu TAEA-H111F Korea
1) Degaussing Coil
6700VS0002F LGIT 3.0 ± 0.05V 65dBu TAEW-G002D PAL 2) Convergency fixing instrument (Speical tools)
6700PF0006B SANYO 2.3 ± 0.05V 65dBu 115-B-A86EL PAL
6870NB0026A LGIT 2.15 ± 0.05V 65dBu TAEA-J001F HITACHI (2) Adjustment Preparation
6700MF0014A LGIT 2.3 ± 0.05V 65dBu TAEW-G013D PAL 1) Operate the unit at least 15 minutes before adjustment.
6700MF0018A LGIT 2.5 ± 0.05V 65dBu TAEA-G011D SECAM(CIS) 2) Using degaussing coil, remove the stains on CPT &
6700MF0018B LGIT 2.4 ± 0.05V 65dBu TAEA-G001D PAL Cabinet.
6700MF0018D LGIT 2.4 ± 0.05V 65dBu TAEA-G011D PAL 3) Received the Cross Hatch Pattern of Convergence. (09ch)
6700MF0018E LGIT 2.5 ± 0.05V 65dBu TAEA-G111D SECAM(CIS) 4) Let the Contrast in normal luminance level.
Copyright©2009 LG Electronics.Inc. All right reserved. -6- LGE Internal Use Only
Only for training and service purposes.
2) Before adjusting Static Convergence (STC), adjust the light with B-BIAS to have the color temperature as
focus first seeing to it that the WHITE color picture quality shown below.
is sharp enough. e. Repeat steps a~d until both low and high light have the
3) Converge the RED vertical and BLUE vertical line in unity same readings as shown below.
(same line) by changing the angle between the 2 tabs of
Market Color Temperature X-AXIS Y-AXIS
4-pole magnet.
ALL 13,000 268±5 273±5
4) Converge the RED horizontal and BLUE horizontal line in
unity(same line) by turning the 2 tabs of the 4-pole
magnet. At this time, do not change the angle between
the 2 tabs. 7. Focus Voltage Adjustment
5) Converge the R, G, B vertical line in unity (same line) by This adjustment must be done after operating the TV set
changing the angle between the 2 tabs of the 6-pole receiver sufficiently.
magnet.
6) Converge the R, G, B horizontal line in unity(same line) by 7-1. Adjustment Preparation
turning the 2 tabs of the 6-pole magnet. At this time, do Receive the LG standard pattern (PAL: Digital pattern,
not change the angle between the 2 tabs. 480NC,13CH) and set the picture condition on “APC ON”
(CLEAR) mode.
(4) Dynamic Convergence (DYC) Adjustment
1) Y-axis Adjustment: 7-2. Adjustment
Adjust convergence of Y-axis (vertical) by moving the Turn the focus volume on the FBT upper direction to have
deflection yoke (DY) left and right. the best focus vertical line (Fig. 1(a)) and horizontal line (Fig.
2) X-axis Adjustment: 1(b)) as shown below.
Adjust convergence of X-axis (horizontal) by moving the
deflection yoke (DY) up and down.
(a)
Copyright©2009 LG Electronics.Inc. All right reserved. -7- LGE Internal Use Only
Only for training and service purposes.
4) Press the VOLF, G key to change the data. 11. Auto Adjustment Preparation
9-2. Adjustment Setting Table
1) Horizontal Position Adjustment
Select SVC02(H-POS) and adjust so that the left and right VIDEO IC EEPROM Speed Delay
vertical line are symmetrical as possible. SLave ADD BA A0 1 5
2) Vertical Position Adjustment TV PC
VCD
Select SVC02(V-POS) and adjust so that the horizontal R DRIVE R BIAS B DRIVE B BIAS B AMP B CUT G AMP G CUT
center line coincide with geometric horizontal center of the Sub Add D A F C
CPT. Start Bit 6 7 6 7
3) Vertical Size Adjustment Stop Bit 0 0 0 0
Select SVC02(VA) and adjust so that the middle circle of the Masking 0 0 0 0
Digital Pattern(480NC, 13CH) coincide with the effective Direction 1 1 1 1
screen of CPT.
EEPROM
8D 8A 8F 8C
Sub Add
9-3. Adjustment (21'' Superslim, Ultra S/S
Model) SpeedPlus
3 3 3 3
Step/Data
1) Vertical Position Adjustment
Select SVC02(V-POS) and adjust so that the horizontal
center line coincide with geometric horizontal center of the
CPT.
2) Vertical linearity Adjustment
Select SVC02(V-LIN) and adjust so that the size of the upper
circle is alike with the one of the lower circle at LG standard
pattern (PAL: EU05CH, NTSC: 13CH)
3) Vertical Size Adjustment
Select SVC02(VA) and adjust so that the middle circle of the
Digital Pattern(PAL B/G 5CH) has 6~7mm gaps from the
effective screen of CPT
4) Horizontal Position Adjustment
Select SVC02(H-POS) and adjust so that the left and right
vertival line are symmetrical as possible.
5) Horizontal Size Adjustment
Select SVC02(EW WIDTH) and adjust so that the outer line of
the left and right and the remotest grid will correspond to the
effective boundary surface. (The remotest grid PAL: within
0~25%; NTSC: within 2.5~3.0 column)
6) Parabora Adjustment
Select SVC02(EW PARAB) and adjust so that the vertical line
of the remotest grid at the left or right side of the screen will
be parallel to the vertical line of the center of screen. (or the
remotest grid of CPT)
7) Trapezoidal Adjustment
Select SVC02(EW TRAPE) and adjust so that the width of
the upper part of screen is alike with the one of the lower part
of the screen.
8) EW UPCOR / LOCOR Adjustment
Select SVC02(EW C UPCOR, EW LOCOR) and adjust so
that the vertical line in the four corners become straight line.
9) BOW Adjustment
Select SVC02(HP BOW) and adjust so that the vertical line in
the four corners become straight line.
Copyright©2009 LG Electronics.Inc. All right reserved. -8- LGE Internal Use Only
Only for training and service purposes.
12. EEPROM OPTION TABLE
( <Table 1> PAL MODEL SOUTH EAST, <Table 2> PAL MODEL MIDDLE EAST)
You can find the EEPROM Option Data if entering the IN-START key of the adjustable remote control and then pressing the MENU key.
<Table 2>
Copyright©2009 LG Electronics.Inc. All right reserved. -9- LGE Internal Use Only
Only for training and service purposes.
<TABLE 3 >
SVC Register Range Initial(PAL) Initial(SECAM) Remark
RF AGC 0 ~ 63 38 38 Necessary
R BIAS 0 ~ 255 90 90 Necessary
G BIAS 0 ~ 255 90 90 Others CPT
127 127 IRICO CPT
Unnecessary
SVC 01 B BIAS 0 ~ 255 90 90 Necessary
R DRIVE 0 ~ 127 90 90 Necessary
G DRIVE 0 ~ 127 85 85 Unnecessary
B DRIVE 0 ~ 127 90 90 Necessary
Y-DELAY 0 ~ 15 7 7 Unnecessary
OSD CONT. 0~7 5 5 Unnecessary
OSD POS. 0 ~ 60 42 40 Unnecessary
V POS 0 ~ 15 6 8 Ultra 2 LG CPT
7 Ultra HF CPT
7 FLAT HF CPT
FLATIRICOCPT
9 FLAT LG CPT
Necessary
V LIN 0 ~ 31 19 18 Ultra 2 LG CPT
18 17 Ultra HF CPT
20 FLAT HF CPT
17 FLATIRICOCPT
19 18 FLAT LG CPT
Unnecessary
VA 0 ~ 127 37 37 Ultra 2 LG CPT
54 Ultra HF CPT
12 FLAT HF CPT
FLATIRICOCPT
22 FLAT LG CPT
Necessary
H POS 0 ~ 31 16 20 Ultra 2 LG CPT
18 Ultra HF CPT
14 FLAT HF CPT
FLATIRICOCPT
16 FLAT LG CPT
Necessary
SVC 02 EW WIDTH 0 ~ 127 65 65 Ultra 2 LG CPT
95 Ultra HF CPT
FLAT HF CPT
FLATIRICOCPT
FLAT LG CPT
Necessary
EW PARAB 0 ~ 127 27 24 Ultra 2 LG CPT
17 Ultra HF CPT
FLAT HF CPT
FLATIRICOCPT
FLAT LG CPT
Necessary
EW TRAPE 0 ~ 127 16 14 Ultra 2 LG CPT
15 Ultra HF CPT
FLAT HF CPT
FLATIRICOCPT
FLAT LG CPT
Necessary
EW UPCOR 0 ~ 31 14 14 Ultra 2 LG CPT
16 Ultra HF CPT
FLAT HF CPT
FLATIRICOCPT
FLAT LG CPT
Necessary
EW COR 0:normal mode 0 0 Unnecessary
1:corner pin gain up mode
1. TV FUNCTIONAL
11100 TUNER / IF 14400 HORZ. DEFL
12500 VIDEO/MICOM
2. TU / IF SECTION
11100 TUNER
11100
2 7 8 10
6 TUNER/IF
(TU101) 11
9
4 5 1
3. VIDEO PROCESSING
12511
PA01,R82,C30,C28,
R154,C101,Z111
12509 KEY I/P Section NO SOUND
DEFLECTION SECTION
LV762XX 17~22
R404,R512,R532,C512,C513
1~13
12502 C515,C516,C517,C523,C544
04,09,35,4
REAR A/V DVD Deflection Problem
12 41 9,62
Vertical/Horizontal Line
AUDIO L/R L IN: L221,C215
R IN: L222,C222 12505
VIDEO IN: L225,R226 12503 12504
POWER SUPPLY SECTION
DVD-Y,Pb,Pr IN: C210,C211,C212
OSC SECTION (4.43MHz) RESET SECTION
DVD-R IN: L221,C215 POWER
DVD-L IN: L222,C222 X501, R22,C15 ST-5V(C521,R528)
R537 RGB 9V(C510,C511,R515)
AUDIO/VIDEO No I/P, O/P IF VCC(C528,C526,L528,C547)
SET Maneuver SET Maneuver
VCC(C518,L503)
defectiveness defectiveness
Clock Error MENU Picture Error SET Maneuver defectiveness
OSD Not Working SET LATCH-UP KEY Not Working No Sound
MENU Picture Error
(S-Vcc)
LA42101 (#7,Vcc) IC 601 (SOUND-amp) 5W MONO
17V 14V / 25mA
20V-(10W) D824 C831
(330u/25V) LA42102 (#7,Vcc) IC 601 (SOUND-amp) 5W+5 W ST
(SFAF504G)
17V LA42102N (#7,Vcc) IC 601 (SOUND-amp) 10W+10W ST
(st-by 5V)
ST-5V
11V KIA78L05BP D-Coil Relay
D813 R873 IC04 T/X Pre-Amp
(RU3AMV) (47/0.5W)
C826
MAIN IC (#24, Vcc)
(1000u/16V) IC806
ST-5V EEPROM (#8, Vcc)
ST_BY 1W KIA78R05API
Option D806
R620
(TVR06J) IC804
(RS 5.6/2W) IC803 5V_1 5.0V / 231mA
KIA78R09API KIA7805API LV76213(#62,#4 Vcc) IC 501 (Main IC)
C838 5.0V / 14mA
(2200u/25V) NT: 398mA
PAL:503mA NT: 360mA LA72730 (#8 Vcc) IC 751 (S/W IC )
PAL:465mA 5.0V / 40mA
SMPS LA72702N (#19 Vcc) IC 661 (RF STEREO NT)
Trans
FBT LA42102 (#5,St-by) IC 601 (SOUND-amp)
85mA
Trans 184.47V / 18mA 3.3V LC75024E (3.3V Vcc) IC 807 (NICAM)
180V CPT Board 3.3V Reg. 5V
1.8V 145mA.
LC75024E (1.5V Vcc)
1.5V Reg.
D505 C540 60mA
(RGP10J)) (4.7u/250V) R520 FM TX, Game, USB OPT
9V (RS 620) 3.3V / 10mA
LV76213(#9, Vcc) IC 501 (Main IC 3.3V Vcc)
28.2V / 320mA R513
LA78040N 9V (RS 300)
5.0V / 13mA
26V (#2,Vcc) LV76213(#20, Vcc) IC 501 (Main IC Hor Vcc)
R529
8.0V / 15mA
D301 9V (RS 68)
(RGP15J)) LV76213(#49,Vcc) IC 501 (Main IC RGB Vcc)
R132
9V 5V /75mA.
C309 (RS 68)
(470u/35V) TUNER(Vcc)
110V FBT B+
D826 R833 L802 FR403
29.97V / 10mA (28V~32V)
(RU3AMV) (RS 0.47/2W) (82uH) (RF 1.2/2W)
Tuner 30V
C831 R107
(220u/160V) (RS 12K/2W)
15300
VERTICAL IC(IC301)
LA78141
15305
O/STAGE
V-IN
PUMP V-
VCC -UP GND OUT
VERTICAL O/P DAMPING V
V-REF & FILTER E
R310,R315,C314,C305,C310 R
15301 T
VERTICAL FOLDING
VERTICAL I/P VERTICAL ROLLING NOISE D
R305,R309,R311,C322 (HORZ LINE MOVING UP/DOWN) Y
15303 15308
VCC SECTION (24V) 15304 OUTPUT STAGE VCC SECTION
FR301,D301,C303,C309,C306 PUMP UP VCC
C307
FBT SEC O/P VCC C307,D302
FULL RASTER
RETRACE LINE
VCT VERT. PROTECTION
VERT. PROTECTION ENABLE ENABLE
CAUSES NO POWER POWER OFF
POWER OFF
7. HORIZONTAL SECTION
COLLECTOR
14410
HEATER
VOLTAGE
.FR401
X-RAY WORKING
SAFETY PROB
ROLLING PICT
180V VOLTAGE
FR501,D505,C540
NO RETRACE
T402
26V VOL
ANODE
FOCUS
SCREEN
ANT.
Speaker
13603
1 CHIP IC NICAM IC
TUNER LA42102L(10W*2))
(LV762XX) (LC75024E)
TUNER : RF signal is feed to TUNER through Antenna. IF output from Tuner is then given to 1 CHIP IC.
1 CHIP IC : 1 CHIP IC processes the input IF. Demodulates Picture and sound information and gives analog R G B
output for Display and SPKL/R as audio output, this sound output is further Amplified and feed to speakers.
Sound Amp : Sound amps(LA42102L) is and Audio Amplifier it amplifies the output sound signal from
L901
180V
Q901
The CPT-BOARD assembly is composed of discrete type RGB
Amplifier. Q903
Amp- Gain is defined by Resistance of R917, R912,R923.
B
L904 R906
R905 R921
C902
9V
R908 C904 R922
D902
VIDEO PROCESSING
11500 SECTION CPT DRIVE
16100 SECTION
L901 16004
180V DISCHARGE
16101 PROTECTION CIRCUIT
R,G,B Signal-IN L902 ONE SIGNAL R/G/B)
L902, L903, L904 MISSING
R NO PICTURE, CPT
ONE SIGNAL (R/G/B) Q901 Dead >
MISSING
G >
L903 R916 CPT / e-GUN
R915 Q902
C907
16002 B >
L904 R906
CPT CIRCUIT VCC / GND R905 R921
1 Vcc 180V 5 GND C902
9V
R908 C904 R922
D902
16005 17006
Spot Killer CIRCUIT Heater Voltage
AUDIO B+
MONO
MONO 9
IC04 (17V/11V)
SOUND
SOUND AMP
AMP L-OUT ST-5V REG
SPK1. SMPS
LA42101
LA42101 9v
SPK2.
From IC803
IC803 R620
R620 TRANS
STEREO,
STEREO, R-OUT IC804 12
IC701
V_DY
BTSC
1 2 5 49 46~48 62 19 9
12 24
LA72702 Ext R/L RGB 17 6
- 18 -
EXT RGB IF H-Vcc VDD Vcc
IN Video-in OUT V-OUT
9V 5V 5V 3.3V 5V 24V
2 7 22
50 SPK L/R USOC
H-OUT
51 OUT 2 185V
LA76213
LA76213
IC661
SIF IN SIF 10 AFC
5 54 IF IN Y(G)/Cr(R)/Cb(B) EW-OUT
A2/NICAM FBT
BLOCK DIAGRAM
out
57 56 64 61 8 33 10 11 13 31 32 16 8 ABL
LC75024E 1
9 HEATER
27 26
FB
ID
Collector
AV
SDA SCL
3 B+
SDA SCL TV IN(ST) IC02
9V EEPROM
M_R/L OUT(ST)
IF SAW
SAW
From 24C04/16
V-OUT (Mono)
AV1(V/R/L)-IN
HDT
IC804 Vcc
FBP in Q402
(Mono)
5V Z102 V-in
M L-OUT
ST-5V MD1803
TUNER Audio(Game)
R,G,
Video(Game)
33V From USOC
5.1V B IC401
JA01 TDA8145
SDA
4,5,6 8 7
EW IN EW OUT
SCL Rear_AV(1) SCART DVD L401
HIC291
HIC291 Rear_AV(1) SCART DVD
Game
Game Pack(Game
Pack(Game Opt)
Opt) (( PHONE)
PHONE) (FLAT
(FLAT OPT.)
OPT.)
CPT (option)
LED+PRE AMP
POWER
943
400
170 150
510
913 174
520
112
540
120
590
591
300
330
311
310
530