Professional Documents
Culture Documents
com
COLOR TV
SERVICE MANUAL
CHASSIS : CW62C
MODEL : 29FU1RLX
MODEL : 29FU1RLX-T1
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
June, 2007
P/NO : MFL37794405 Printed in China
Contents ...................................................................................................................2
Safety Precautions..............................................................................................3
Control Descriptions..........................................................................................4
Specifications........................................................................................................7
Exploded View....................................................................................................24
SVC. Sheet..................................................................................................................
-2-
An isolation Transformer should always be used during always perform an AC leakage current check on the exposed
the servicing of a receiver whose chassis is not isolated from metallic parts of the cabinet, such as antennas, terminals, etc.,
the AC power line. Use a transformer of adequate power rating to be sure the set is safe to operate without damage of
as this protects the technician from accidents resulting in electrical shock.
personal injury from electrical shocks.
Leakage Current Cold Check(Antenna Cold Check)
It will also protect the receiver and it's components from being With the instrument AC plug removed from AC source,
damaged by accidental shorts of the circuitry that may be connect an electrical jumper across the two AC plug prongs.
inadvertently introduced during the service operation. Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
If any fuse (or Fusible Resistor) in this TV receiver is blown, ohm-meter lead in turn to each exposed metallic parts such as
replace it with the specified. antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
When replacing a high wattage resistor (Oxide Metal Film measured resistance should be between 1MΩ and 5.2MΩ.
Resistor, over 1W), keep the resistor 10mm away from PCB. When the exposed metal has no return path to the chassis the
reading must be infinite.
Keep wires away from high voltage or high temperature parts. An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube. Leakage Current Hot Check (See below Figure)
Do not lift the Picture tube by it's Neck. Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
X-RAY Radiation Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
Warning: and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
The source of X-RAY RADIATION in this TV receiver is the voltmeter with 1000 ohms/volt or more sensitivity.
High Voltage Section and the Picture Tube. Reverse plug the AC cord into the AC outlet and repeat AC
For continued X-RAY RADIATION protection, the voltage measurements for each exposed metallic part. Any
replacement tube must be the same type tube as specified in voltage measured must not exceed 0.75 volt RMS which is
the Replacement Parts List. corresponds to 0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
To determine the presence of high voltage, use an accurate
high impedance HV meter. Leakage Current Hot Check circuit
1.5 Kohm/10W
-3-
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
1 10
1. POWER
switches the set on from standby or off to standby.
3 11
2. NUMBER BUTTONS
PR
Switches the set on from standby or directly select a number.
3. MENU
VOL OK VOL
4 selects a menu.
13 PR 4. D / E (Programme Up/Down)
14 selects a programme or a menu item.
switches the set on from standby.
6 scans programmes automatically.
5 F / G (Volume Up/Down)
adjusts the volume.
12 adjusts menu settings.
7 OK
accepts your selection or displays the current mode.
-4-
10. MUTE
2
switches the sound on or off.
11. TV/AV
selects TV or AV mode.
switches the set on from standby. 3 11
exits the Teletext mode.
PR
12. I/II/
* the language during dual language broadcast.
selects
4 VOL OK VOL
selects the sound output (option).
Q.VIEW LIST
PR
13. Q.VIEW (or YELLOW) 13 14
returns to the previously viewed programme. 9
14. LIST (or BLUE) 6 8
displays the programme table.
12
PR
VOL OK VOL
PR
-5-
2. POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby
mode.
dims when the set is switched on.
1 2 3
3. MENU
selects a menu.
4. OK
4 accepts your selection or displays the current
OK
mode.
F / G (Volume Down/Up)
adjusts the volume.
5
PR
adjusts menu settings.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
-6-
-7-
following conditions.
1) Temperature: 25±5°C STC Pre-Adjustment
2) Humidity : 65±10%
(4) AC Voltage 220V ±10% Purity adjustment
15 ~ 20mm
Following direction is a case using of None-ITC CPT for CPT This adjustment should be operated at the best condition of
manufacture factory. FOCUS after finishing the PURITY adjustment.
This adjustment should be done as below direction. 1) BACK RASTER receives black CROSS HATCH signal.
2) Adjust Brightness so that there are 9-12 dots.
3) Widen two tabs of 4pole Magnet with equal angles and
accord red, blue vertical lines at the center of screen.
4) With keeping angle of "c. clause", rotate tab and accord
red/blue, green vertical lines at the center of screen.
-8-
-9-
EP
CRNL
CRNL6
- 10 -
Warning: First adjust in PAL 50HZ, and then adjust in NTSC 60HZ, but it needs confirm
adjustment state again in NTSC System. Adjust if necessary.
-PAL
- 11 -
RPO RATION POSITIVE/NEGATIVE PEAK 3 3 3 3 OPTION2 SOUND 0: RF stereo, 1:AV stereo, 2: Mono, 3: Mono Dual
RPA RATION PRE/AFTER SHOOT 2 2 2 2 PIP 0: No PIP, 1: 1 Tuner PIP, 2: 2 Tuner PIP, 3: Reserved
PWLDAC PWLDAC PEAK WHITE LIMITER DAC 8 2 8 5 VOL CURVE(volume curve) 0: EU=>Low curve, 1: NON-EU=>High curve
IFOFF IF DEMODULATIOR 37 37 37 37 A2 STEREO Nicam check & FM stereo / Dual
CHSE CHROMA SENSITIVITY 1 1 1 1 I/II SAVE 0: OFF, 1:ON=>Dual sound setting save on
ACL AUTO COLOR LIMITING 1 1 1 1 AV3 0: W/O SIDE A/V, 1: W/ SIDE A/V
CLPDEL50 PAL CLAMPING DELAY 20 20 20 20
OPTION3 SCART 0: No SCART, 1: 1 SCART, 2: 2 SCART, 3: Reserved
CLPDEL60 NTSC CLAMPING DELAY 2 2 2 2
DVD 0: W/O DVD, 1: W/ DVD
CLPLEN CLAMPING PULSE LENGTH 3 3 3 3
XWAVE 0: W/O XWAVE, 1: W/ XWAVE
CLMPID CLAMPING DURATION 3 3 3 3
EYE 0: W/O EVE, 1: W/ EYE
- 12 -
- 13 -
3 RESERVED
4 RESERVED
5 RESERVED
6 RESERVED
7 RESERVED
10 Korea/Middle south America
11 Taiwan
- 14 -
2 Input TV
3 MEMORY CH. MEMORY refer to
CHANNEL manage benchmark
4 SOUND 30 STEPS
5 MUTE OFF
6 PSM DYNAMIC
7 XD ON
8 SSM FLAT
10 AVL OFF
11 BALANCE 0
17 TILT 0 OPTION
6. SOUND PRE-SCALER
This SVC setting value is set since Model design for standard, so
adjustment should not be done at manufacture process. This
adjustment specification shows for only reference.
- 15 -
OK
NO
Check the waveform IF 1 of TU101 Check/ Replace TU101 or Input signal
OK
NO NO
Check the voltage at pin 3, 9, 16, 43,
Check the waveform at pin 4, 5 of IC501 Check/ Replace IC501
86, 88, 90 of UOCIII
OK
NO
Check the voltage at pin 57, 58 of
Check the waveform at pin 4, 2 of IC601
UOCIII
OK
NO
Check the waveform at pin 6 of IC601 Check/ Replace Q601
OK
NO
Check the waveform at pin 8, 9, 11, 12
Check/ Replace IC601
of IC601
OK
NO
Check the waveform at pin 5, 7 of IC601 Check/ Replace R823, D826
Check HV, Screen voltage of CPT Check R, G, B out of CPT board Check the Heater pulse of FBT T402
Check IC901,
Check FBT T402 Check 197V line of CPT Board & Check FR901, P403A, Check FBT T402
P403A
if no problem check and Replace P902B, FR401
- 16 -
OPEN
NO Check Fuse of AC line
Is the voltage each
pin voltage of IC501
Check/ Replace
IC501 Check/ Replace DB801
Check Q402
collector waveform Check the voltage NO
pin4 of IC810
Check/ Replace
Q402
Check/ Replace Fuse and IC810
Check T401 & each
pin voltage
Check/ Replace
IC810, IC802, Q830
Check/ Replace
T401
Check Q401collect NO
Check Fuse and Diode of secondary
waveform
Load of SMPS trans(T801)
Check/ Replace
Q401
OK
Check & Replace Check/ Replace IC501
T402
- 17 -
NO
OK
OK
Check IC501 pin 83, Check receiving system in MENU OK
84, 85 (R, G, B out) & execute Auto - Program
OK
NO NO
Check the waveform Check IC501 pin 83, Check SMPS Trans Go to No sound/
pin73(H-out) 84, 85 (R, G, B out) Secondary Voltage picture OK
OK
OK
NO
Check pin7, 8 SCL, Check IC12(EEPROM)
SDA & SCL, SDA, Line
OK
OK
Replace IC501
- 18 -
OK
OK
Check the connection of AV
equipment
AV
OK
NO
Check the waveform at
Check the signal line of SPK-N,P
pin4, 12, of IC601
OK
NO
Check the waveform at
Check pin5 (mute) of IC501
pin6 of IC601
OK
NO NO
Check the waveform at Check the voltage at Check/ Replace
pin8, 9, 11, 12 of IC601 pin5, 7, of IC601 R823, D826
OK
NO
Check the connection of side
Correct the Board
or Front AV Board P201A
OK
Replace IC601
- 19 -
- 20 -
CONTROL
PIP (option)
- 21 -
- 22 -
- 23 -
400
102
520
150
311
310
530
170
120
590
112
320
591
540
120
330
102
101
300
- 24 -