Professional Documents
Culture Documents
BHEL Haridwar Block 3 Turbine Manufacturing Training Report PDF
BHEL Haridwar Block 3 Turbine Manufacturing Training Report PDF
Training report
On
“TURBINE MANUFACTURING”
At
BHEL HARIDWAR
Bachelor of Technology
In
Mechanical Engineering
“Inspiration and motivation have always played a key role in the success of any
venture.”
[i]
INDEX
1. BHEL 2 – 17
1.1.OVERVIEW 2
1.2.WORKING AREAS 3
1.2.1 POWER GENERATION 3
1.2.2 POWER TRANSMISSION &DISTRIBUTION 3
1.2.3 INDUSTRIES 4
1.2.4 TRANSPORTATION 5
1.2.5 TELECOMMUNICATION 5
1.2.6 RENEWABLE ENERGY 5
1.2.7 INTERNATIONAL OPERATIONS 6
1.3 TECHNOLOGY UP GRADATION AND 7
RESEARCH AND DEVELOPMENT
1.3.1HUMAN RESOURCE DEVELOPMENT INSTITUTE 7
1.4 HEALTH, SAFETY AND ENVIRONMENT 8
MANAGEMENT
1.4.1 ENVIRONMENTAL POLICY 8
1.4.2 OCCUPATIONAL HEALTH AND SAFETY POLICY 8
1.4.3 PRINCIPLES OF THE "GLOBAL COMPACT" 9
1.5 BHEL UNITS 11
1.6 BHEL HARIDWAR 13
1.6.1LOCATION 13
1.6.2ADDRESS 13
1.6.3 AREA 13
1.6.4 UNITS 14
1.6.5 HEEP PRODUCT PROFILE 16
[ii]
2. STEAM TURBINE 18-21
2.1 INTRODUCTION 18
2.2 ADVANTAGES 20
2.3DISADVANTAGES 21
2.4 STEAM TURBINES THE MAINSTAY OF BHEL 21
[iii]
6.2.2 SECONDAY OR MACHINING PROCESSES 36
7. BLOCK-3 LAY-OUT 38
10. CONCLUSION 46
[iv]
FIGURE INDEX
[v]
TABLE INDEX
[vi]
INTRODUCTION
BHEL caters to core sectors of the Indian Economy viz., Power Generation's &
Transmission, Industry, Transportation, Telecommunication, Renewable Energy,
Defense, etc. The wide network of BHEL's 14 manufacturing division, four power
Sector regional centers, over 150 project sites, eight service centers and 18 regional
offices, enables the Company to promptly serve its customers and provide them with
suitable products, systems and services – efficiently and at competitive prices. BHEL
has already attained ISO 9000 certification for quality management, and ISO 14001
certification for environment management.
The company’s inherent potential coupled with its strong performance make this
one of the “NAVRATNAS”, which is supported by the government in their endeavor to
become future global players.
1
1. BHEL
1.1. OVERVIEW
Established in 1960s under the Indo-Soviet Agreements of 1959 and 1960 in the
area of Scientific, Technical and Industrial Cooperation.
BHEL has its setup spread all over India namely New Delhi, Gurgaon, Haridwar,
Rudrapur, Jhansi, Bhopal, Hyderabad, Jagdishpur , Tiruchirapalli, Bangalore and
many more.
BHEL has already attained ISO 9000 certification for quality management, and
ISO 14001 certification for environment management.
It is one of India's nine largest Public Sector Undertakings or PSUs, known as the
NAVRATNAS or 'the nine jewels'
2
1.2. WORKING AREAS
Power generation sector comprises thermal, gas, hydro and nuclear power plant
business as of 31.03.2001, BHEL supplied sets account for nearly 64737 MW or 65% of
the total installed capacity of 99,146 MW in the country, as against nil till 1969-70.
BHEL has proven turnkey capabilities for executing power projects from concept
to commissioning, it possesses the technology and capability to produce thermal sets with
super critical parameters up to 1000 MW unit rating and gas turbine generator sets of up
to 240 MW unit rating. Co-generation and combined-cycle plants have been introduced
to achieve higher plant efficiencies. to make efficient use of the high-ash-content coal
available in India, BHEL supplies circulating fluidized bed combustion boilers to both
thermal and combined cycle power plants.
The company manufactures 235 MW nuclear turbine generator sets and has
commenced production of 500 MW nuclear turbine generator sets.
Custom made hydro sets of Francis, Pelton and Kaplan types for different head
discharge combination are also engineering and manufactured by BHEL.
In all, orders for more than 700 utility sets of thermal, hydro, gas and nuclear have
been placed on the Company as on date. The power plant equipment manufactured by
BHEL is based on contemporary technology comparable to the best in the world and is
also internationally competitive.
BHEL offer wide ranging products and systems for T & D applications. Products
manufactured include power transformers, instrument transformers, dry type
3
transformers, series – and stunt reactor, capacitor tanks, vacuum – and SF circuit breakers
gas insulated switch gears and insulators.
1.2.3. INDUSTRIES
4
The Company has commenced manufacture of large desalination plants to help
augment the supply of drinking water to people.
1.2.4. TRANSPORTATION
1.2.5. TELECOMMUNICATION
5
1.2.7. INTERNATIONAL OPERATIONS
BHEL has, over the years, established its references in around 60 countries of the
world, ranging for the United States in the west to New Zealand in the far east. these
references encompass almost the entire product range of BHEL, covering turnkey power
projects of thermal, hydro and gas-based types, substation projects, rehabilitation
projects, besides a wide variety of products, like transformers, insulators, switchgears,
heat exchangers, castings and forgings, valves, well-head equipment, centrifugal
compressors, photo-voltaic equipment etc. apart from over 1110mw of boiler capacity
contributed in Malaysia, and execution of four prestigious power projects in Oman, some
of the other major successes achieved by the company have been in Australia, Saudi
Arabia, Libya, Greece, Cyprus, Malta, Egypt, Bangladesh, Azerbaijan, Sri Lanka, Iraq
etc.
The success in the area of rehabilitation and life extension of power projects has
established BHEL as a comparable alternative to the original equipment manufacturers
(OEM’S) for such plants.
6
1.3. TECHNOLOGY UPGRADATION AND RESEARCH & DEVELOPMENT
The Corporate R&D Division at Hyderabad, spread over a 140 acre complex,
leads BHEL's research efforts in a number of areas of importance to BHEL's product
range. Research and product development centers at each of the manufacturing divisions
play a complementary role.
Some of the on-going development & demonstration projects include: Smart wall
blowing system for cleaning boiler soot deposits, and micro-controller based governor for
diesel-electric locomotives. The company is also engaged in research in futuristic areas,
such as application of super conducting materials in power generations and industry, and
fuel cells for distributed, environment-friendly power generation.
The most prized asset of BHEL is its employees. The Human Resource
Development Institute and other HRD centers of the Company help in not only keeping
their skills updated and finely honed but also in adding new skills, whenever required.
Continuous training and retraining, positive, a positive work culture and participative
7
style of management, have engendered development of a committed and motivated work
force leading to enhanced productivity and higher levels of quality.
8
Formulation and maintenance of OH&S Management programs for continual
improvement;
The major units of BHEL have already acquired ISO 14001 Environmental
Management System Certification, and other units are in advanced stages of acquiring the
same. Action plan has been prepared to acquire OHSAS 18001 Occupational Health and
Safety Management System certification for all BHEL units.
The "Global Compact" is a partnership between the United Nations, the business
community, international labor and NGOs. It provides a forum for them to work together
and improve corporate practices through co-operation rather than confrontation.
BHEL has joined the "Global Compact" of United Nations and has committed to
support it and the set of core values enshrined in its nine principles:
HUMAN RIGHTS
9
LABOUR STANDARDS
3. Business should uphold the freedom of association and the effective recognition
of the right to collective bargaining;
6. Eliminate discrimination.
ENVIRONMENT
By joining the "Global Compact", BHEL would get a unique opportunity of networking
with corporate and sharing experience relating to social responsibility on global basis.
10
1.5. BHEL UNITS
2. Haridwar
3.Hyderabad
4.Tiruchi
HPBP High Pressure Boiling Steam less steel tubes, Spiral fin welded
Plant tubes.
SSTP
5.Jhansi
Transformers, Diesel shunt less AC locos
TP Transformer Plant
and AC EMU
11
6.Banglore
7.Ranipet
Electrostatic precipitator, Air pre-heater,
BAP Boiler Auxiliaries Plant
Fans, Wind electric generators, Desalination
plants.
8.Goindwal Industrial Valves Plant Industrial valves and Fabrication
9.Jagdishpur
TABLE1
12
1.6. BHEL HARIDWAR
1.6.1. LOCATION
1.6.2. ADDRESS
Ranipur, Haridwar
PIN:- 249403
1.6.3. AREA
The Heavy Electricals Equipment Plant (HEEP) located in Haridwar, is one of the
major manufacturing plants of BHEL. The core business of HEEP includes design and
manufacture of large steam and gas turbines, turbo generators, hydro turbines and
generators, large AC/DC motors and so on.
1.6.4. UNITS
13
THERE ARE 8 BLOCKS IN HEEP
I. Electrical Machine Turbo generator, generator exciter , motor (ac and dc)
III. Turbine & Auxiliary Steam ,hydro ,gas turbines, turbine blade , special tooling
VI. Fabrication Fabricated oil tanks, hollow guide blades, Rings, stator frames
and rotor spindle, all dies, stamping for generators and
Stamping and die
motors
manufacturing
14
VII. Wood working Wooden packing, spacers.
VIII. Heaters & coolers LP heaters, ejectors, glands, steam and oil coolers,
TABLE 2
TABLE 3
15
1.6.5. HEEP PRODUCT PROFILE
1. THERMAL SETS:
Steam turbines and generators up to 500 MW capacity for utility and combined
cycle applications
Capability to manufacture up to 1000 MW unit cycle.
2. GAS TURBINES:
Gas turbines for industry and utility application; range-3 to 200 MW (ISO).
Gas turbines based co-generation and combined cycle system .
3. HYDRO SETS:
Custom– built conventional hydro turbine of Kaplan, Francis and Pelton with
matching generators up to 250 MW unit size.
Pump turbines with matching motor-generators.
Mini / micro hydro sets.
Spherical butterfly and rotary valves and auxiliaries for hydro station.
5. ELECTRICAL MACHINES:
DC general purpose and rolling mill machines from 100 to 19000KW suitable for
operation on voltage up to 1200V. These are provided with STDP, totally
enclosed and duct ventilated enclosures.
DC auxiliary mill motors.
16
6. CONTROL PANEL:
Control panel for voltage up to 400KW and control desks for generating stations
and EMV sub–stations.
8. DEFENCE:
Naval guns with collaboration of Italy.
17
2. STEAM TURBINE
2.1 INTRODUCTION
In a steam turbine, the steam’s energy is extracted through the turbine and the steam
leaves the turbine at a lower energy state. High pressure and temperature fluid at the inlet
of the turbine exit as lower pressure and temperature fluid. The difference is energy
converted by the turbine to mechanical rotational energy, less any aerodynamic and
mechanical inefficiencies incurred in the process. Since the fluid is at a lower pressure at
the exit of the turbine than at the inlet, it is common to say the fluid has been “expanded”
across the turbine. Because of the expanding flow, higher volumetric flow
18
occurs at the turbine exit (at least for compressible fluids) leading to the need for larger
turbine exit areas than at the inlet.
The generic symbol for a turbine used in a flow diagram is shown in Figure
below. The symbol diverges with a larger area at the exit than at the inlet. This is how
one can tell a turbine symbol from a compressor symbol. In Figure , the graphic is
colored to indicate the general trend of temperature drop through a turbine. In a turbine
with a high inlet pressure, the turbine blades convert this pressure energy into velocity or
kinetic energy, which causes the blades to rotate. Many green cycles use a turbine in this
fashion, although the inlet conditions may not be the same as for a conventional high
pressure and temperature steam turbine. Bottoming cycles, for instance, extract fluid
energy that is at a lower pressure and temperature than a turbine in a conventional power
plant. A bottoming cycle might be used to extract energy from the exhaust gases of a
large diesel engine, but the fluid in a bottoming cycle still has sufficient energy to be
extracted across a turbine, with the energy converted into rotational energy.
Turbines also extract energy in fluid flow where the pressure is not high but
where the fluid has sufficient fluid kinetic energy. The classic example is a wind turbine,
which converts the wind’s kinetic energy to rotational energy. This type of kinetic energy
conversion is common in green energy cycles for applications ranging from larger wind
turbines to smaller hydrokinetic turbines currently being designed for and demonstrated
in river and tidal applications. Turbines can be designed to work well in a variety of
fluids, including gases and liquids, where they are used not only to drive generators, but
also to drive compressors or pumps.
19
One common (and somewhat misleading) use of the word “turbine” is “gas
turbine,” as in a gas turbine engine. A gas turbine engine is more than just a turbine and
typically includes a compressor, combustor and turbine combined to be a self-contained
unit used to provide shaft or thrust power. The turbine component inside the gas turbine
still provides power, but a compressor and combustor are required to make a self-
contained system that needs only the fuel to burn in the combustor.
Also note that turbines in high inlet-pressure applications are sometimes called
expanders. The terms “turbine” and “expander” can be used interchangeably for most
applications, but expander is not used when referring to kinetic energy applications, as
the fluid does not go through significant expansion.
2.2. ADVANTAGES:-
Ability to utilize high pressure and high temperature steam.
High efficiency.
High rotational speed.
High capacity/weight ratio.
Smooth, nearly vibration-free operation.
No internal lubrication.
Oil free exhausts steam.
20
2.3 DISADVANTAGES:-
For slow speed application reduction gears are required. The steam turbine cannot
be made reversible. The efficiency of small simple steam turbines is poor.
21
3. TYPES OF STEAM TURBINE
There are complicated methods to properly harness steam power that give rise to
the two primary turbine designs: impulse and reaction turbines. These different designs
engage the steam in a different method so as to turn the rotor
The steam passes through the stationary nozzles and is directed at high velocity against
rotor buckets causing the rotor to rotate at high speed.
22
pressure at the inlet to the moving blades is the same as the pressure at the outlet from
the moving blades.
A reaction turbine has rows of fixed blades alternating with rows of moving
blades. The steam expands first in the stationary or fixed blades where it gains some
velocity as it drops in pressure. It then enters the moving blades where its direction of
flow is changed thus producing an impulse force on the moving blades. In addition,
however, the steam upon passing through the moving blades again expands and further
drops in pressure giving a reaction force to the blades. This sequence is repeated as the
steam passes through additional rows of fixed and moving blades.
In order for the steam to give up all its kinetic energy to the moving blades in an
impulse turbine, it should leave the blades at zero absolute velocity. This condition will
exist if the blade velocity is equal to one half of the steam velocity. Therefore, for good
efficiency the blade velocity should be about one half of steam velocity.
In order to reduce steam velocity and blade velocity, the following methods may be used:
1. Pressure compounding.
2. Velocity compounding.
3. Pressure-velocity compounding.
4. Pressure Compounding
23
4. TURBINE PARTS
Casings or cylinders are of the horizontal split type. This is not ideal, as the heavy
flanges of the joints are slow to follow the temperature changes of the cylinder walls.
However, for assembling and inspection purposes there is no other solution. The casing is
heavy in order to withstand the high pressures and temperatures. It is general practice to
let the thickness of walls and flanges decrease from inlet- to exhaust-end.
The casing joints are made steam tight, without the use of gaskets, by matching
the flange faces very exactly and very smoothly. The bolt holes in the flanges are drilled
for smoothly fitting bolts, but dowel pins are often added to secure exact alignment of the
flange joint. Double casings are used for very high steam pressures. The high pressure is
applied to the inner casing, which is open at the exhaust end, letting the turbine exhaust to
the outer casings.
24
4.3 TURBINE ROTORS
The design of a turbine rotor depends on the operating principle of the turbine. The
impulse turbine with pressure drop across the stationary blades must have seals between
stationary blades and the rotor. The smaller the sealing area, the smaller the leakage;
therefore the stationary blades are mounted in diaphragms with labyrinth seals around the
shaft. This construction requires a disc rotor. Basically there are two types of rotor:
DISC ROTORS
All larger disc rotors are now machined out of a solid forging of nickel steel;
this should give the strongest rotor and a fully balanced rotor. It is rather
expensive, as the weight of the final rotor is approximately 50% of the initial
forging. Older or smaller disc rotors have shaft and discs made in separate
pieces with the discs shrunk on the shaft. The bore of the discs is made 0.1%
smaller in diameter than the shaft. The discs are then heated until they easily
are slid along the shaft and located in the correct position on the shaft and
shaft key. A small clearance between the discs prevents thermal stress in the
shaft.
DRUM ROTORS
The first reaction turbines had solid forged drum rotors. They were strong,
generally well balanced as they were machined over the total surface. With the
increasing size of turbines the solid rotors got too heavy pieces. For good
balance the drum must be machined both outside and inside and the drum
must be open at one end. The second part of the rotor is the drum end cover
with shaft.
25
5. CONSTRUCTIONAL FEATURES OF A BLADE
The profile, which converts the thermal energy of steam into kinetic energy, with
a certain efficiency depending upon the profile shape.
The root, which fixes the blade to the turbine rotor, giving a proper anchor to the
blade, and transmitting the kinetic energy of the blade to the rotor.
The damping element, which reduces the vibrations which necessarily occur in
the blades due to the steam flowing through the blades. These damping elements
may be integral with blades, or they may be separate elements mounted between
the blades.
Each of these elements will be separately dealt with in the following sections.
CAMBER LINE
CHORD
BITANGENT LINE
26
If circles are drawn tangential to the suction side and pressure side profiles of a
blade, and their centers are joined by a curve, this curve is called the camber line. This
camber line intersects the profile at two points A and B. The line joining these points is
called chord, and the length of this line is called the chord length. A line which is
tangential to the inlet and outlet edges is called the bitangent line. The angle which this
line makes with the circumferential direction is called the setting angle. Pitch of a blade is
the circumferential distance between any point on the profile and an identical point on the
next blade.
There are two basic types of profiles - Impulse and Reaction. In the impulse type
of profiles, the entire heat drop of the stage occurs only in the stationary blades. In the
reaction type of blades, the heat drop of the stage is distributed almost equally between
the guide and moving blades.
Though the theoretical impulse blades have zero pressure drop in the moving
blades, practically, for the flow to take place across the moving blades, there must be a
small pressure drop across the moving blades also. Therefore, the impulse stages in
practice have a small degree of reaction. These stages are therefore more accurately,
though less widely, described as low-reaction stages.
The presently used reaction profiles are more efficient than the impulse profiles at
part loads. This is because of the more rounded inlet edge for reaction profiles. Due to
this, even if the inlet angle of the steam is not tangential to the pressure-side profile of the
blade, the losses are low.
However, the impulse profiles have one advantage. The impulse profiles can take
a large heat drop across a single stage, and the same heat drop would require a greater
number of stages if reaction profiles are used, thereby increasing the turbine length.
27
The Steam turbines use the impulse profiles for the control stage (1st stage), and
the reaction profiles for subsequent stages. There are three reasons for using impulse
profile for the first stage.
a) Most of the turbines are partial arc admission turbines. If the first stage is a
reaction stage, the lower half of the moving blades do not have any inlet
steam, and would ventilate. Therefore, most of the stage heat drop should
occur in the guide blades.
b) The heat drop across the first stage should be high, so that the wheel chamber
of the outer casing is not exposed to the high inlet parameters. In case of -4
turbines, the inner casing parting plane strength becomes the limitation, and
therefore requires a large heat drop across the 1st stage.
c) Nozzle control gives better efficiency at part loads than throttle control.
d) The number of stages in the turbine should not be too high, as this will
increase the length of the turbine.
There are exceptions to the rule. Turbines used for CCPs, and BFP drive turbines
do not have a control stage. They are throttle-governed machines. Such designs are used
when the inlet pressure slides. Such machines only have reaction stages. However, the
inlet passages of such turbines must be so designed that the inlet steam to the first
reaction stage is properly mixed, and occupies the entire 360 degrees. There are also
cases of controlled extraction turbines where the L.P. control stage is an impulse stage.
This is either to reduce the number of stages to make the turbine short, or to increase the
part load efficiency by using nozzle control, which minimizes throttle losses.
The root is a part of the blade that fixes the blade to the rotor or stator. Its design
depends upon the centrifugal and steam bending forces of the blade. It should be
designed such that the material in the blade root as well as the rotor / stator claw and any
fixing element are in the safe limits to avoid failure. The roots are T-root and Fork-root.
The fork root has a higher load-carrying capacity than the T-root. It was found that
28
machining this T-root with side grip is more of a problem. It has to be machined by
broaching, and the broaching machine available could not handle the sizes of the root.
The typical roots used for the HP moving blades for various steam turbine applications
are shown in the following figure:
T-ROOT
FORK ROOT
29
5.4 L.P. BLADE PROFILES
The LP blade profiles of moving blades are twisted and tapered. These blades are
used when blade height-to-mean stage diameter ratio (h/Dm) exceeds 0.2.
1) 2 blading :
The roots of both the LP stages in –2 type of LP blading are T-roots.
2) 3 blading:
The last stage LP blade of HK, SK and LK blades have a fork-root. SK blades have
4-fork roots for all sizes. HK blades have 4-fork roots up to 56 size, where modified
profiles are used. Beyond this size, HK blades have 3 fork roots. LK blades have 3-fork
roots for all sizes. The roots of the LP blades of preceding stages are of T-roots.
The excitation of any blade comes from different sources. They are:
a) Nozzle-passing excitation: As the blades pass the nozzles of the stage, they
encounter flow disturbances due to the pressure variations across the guide blade
passage. They also encounter disturbances due to the wakes and eddies in the flow
path. These are sufficient to cause excitation in the moving blades. The excitation
gets repeated at every pitch of the blade. This is called nozzle-passing frequency
excitation. The order of this frequency = no. of guide blades x speed of the
machine. Multiples of this frequency are considered for checking for resonance.
30
For HP blades, due to the thick and cylindrical cross-sections and short blade heights, the
natural frequencies are very high. Nozzle-passing frequencies are therefore necessarily
considered, since resonance with the lower natural frequencies occurs only with these
orders of excitation.
In LP blades, since the blades are thin and long, the natural frequencies are low.
The excitation frequencies to be considered are therefore the first few multiples of speed,
since the nozzle-passing frequencies only give resonance with very high modes, where
the vibration stresses are low.
The HP moving blades experience relatively low vibration amplitudes due to their
thicker sections and shorter heights. They also have integral shrouds. These shrouds of
adjacent blades butt against each other forming a continuous ring. This ring serves two
purposes – it acts as a steam seal, and it acts as a damper for the vibrations. When
vibrations occur, the vibration energy is dissipated as friction between shrouds of
adjacent blades.
For HP guide blades of Wesel design, the shroud is not integral, but a shroud band
is riveted to a number of guide blades together. The function of this shroud band is
mainly to seat the steam. In some designs HP guide blades may have integral shrouds like
moving blades. The primary function remains steam sealing.
31
also, it is not possible to avoid resonance. In such cases, where it is not possible to avoid
resonance, a damping element is to be used in the LP blades to reduce the dynamic
stresses, so that the blades can operate continuously under resonance also. There may be
blades which are not adequately damped due to manufacturing inaccuracies. The need for
a damping element is therefore eliminated. In case the frequencies of the blades tend
towards resonance due to manufacturing inaccuracies, tuning is to be done on the blades
to correct the frequency. This tuning is done by grinding off material at the tip (which
reduces the inertia more than the stiffness) to increase the frequency, and by grinding off
material at the base of the profile (which reduces the stiffness more than the inertia) to
reduce the natural frequency.
This condition gives zero friction damping, and only the material and
aerodynamic damping exists. In a periodically varying excitation force, it may frequently
happen that the force is less than the friction force. During this phase, the damping is very
32
less. At the same time, due to the locking of the rubbing surfaces, the overall stiffness
increases and the natural frequency shifts drastically away from the individual value. The
response therefore also changes in the locked condition. The resonant response of a
system therefore depends upon the amount of damping in the system (which is
determined by the relative duration of slip and stick in the system, i.e., the relative
magnitude of excitation and friction forces) and the natural frequency of the system
(which alters between the individual values and the locked condition value, depending
upon the slip or stick condition).
Among the different materials typically used for blading are 403 stainless steel,
422 stainless steel, A-286, and Haynes Stellite Alloy Number 31 and titanium alloy. The
403 stainless steel is essentially the industry’s standard blade material and, on impulse
steam turbines, it is probably found on over 90 percent of all the stages. It is used because
of its high yield strength, endurance limit, ductility, toughness, erosion and corrosion
resistance, and damping. It is used within a Brinell hardness range of 207 to 248 to
maximize its damping and corrosion resistance. The 422 stainless steel material is applied
only on high temperature stages (between 700 and 900°F or 371 and 482°C), where its
higher yield, endurance, creep and rupture strengths are needed.
The A-286 material is a nickel-based super alloy that is generally used in hot gas
expanders with stage temperatures between 900 and 1150°F (482 and 621°C). The
Haynes Stellite Alloy Number 31 is a cobalt-based super alloy and is used on jet
expanders when precision cast blades are needed. The Haynes Stellite Number 31 is used
at stage temperatures between 900 and 1200°F (482 and 649°C). Another blade material
is titanium. Its high strength, low density, and good erosion resistance make it a good
candidate for high speed or long-last stage blading.
33
6. MANUFACTURING PROCESS
6.1 INTRODUCTION
34
rolling mills to obtain market form of material supply in form of bloom, billets, slabs and
rods.
These forms of material supply are further subjected to various manufacturing processes
for getting usable metal products of different shapes and sizes in various manufacturing
shops. All these processes used in manufacturing concern for changing the ingots into
usable products may be classified into six major groups as
(1) Casting
(2) Powder metallurgy
(3) Plastic technology
(4) Gas cutting
(5) Bending and
(6) Forging.
35
6.2.2 SECONDARY OR MACHINING PROCESSES
As large number of components require further processing after the primary
processes. These components are subjected to one or more number of machining
operations in machine shops, to obtain the desired shape and dimensional accuracy on flat
and cylindrical jobs. Thus, the jobs undergoing these operations are the roughly finished
products received through primary shaping processes. The process of removing the
undesired or unwanted material from the work-piece or job or component to produce a
required shape using a cutting tool is known as machining. This can be done by a manual
process or by using a machine called machine tool (traditional machines namely lathe,
milling machine, drilling, shaper, planner, slotter). In many cases these operations are
performed on rods, bars and flat surfaces in machine shops.
These secondary processes are mainly required for achieving dimensional
accuracy and a very high degree of surface finish. The secondary processes require the
use of one or more machine tools, various single or multi-point cutting tools (cutters), job
holding devices, marking and measuring instruments, testing devices and gauges etc. for
getting desired dimensional control and required degree of surface finish on the work-
pieces. The example of parts produced by machining processes includes hand tools
machine tools instruments, automobile parts, nuts, bolts and gears etc. Lot of material is
wasted as scrap in the secondary or machining process. Some of the common secondary
or machining processes are:
Turning
Threading
Knurling
Milling
Drilling
Boring
Planning
Shaping
Slotting
Sawing
36
Broaching
Hobbing
Grinding
Gear Cutting
Thread cutting and
Unconventional machining processes namely machining with Numerical
control (NC) machines tools or Computer Numerical Control(CNC)
machine tool using ECM, LBM, AJM, USM setups.
37
7. BLOCK 3 LAY-OUT
38
8. CLASSIFICATION OF BLOCK 3
BAY-1 IS FURTHER DIVIDED INTO THREE PARTS
1. HMS -
In this shop heavy machine work is done with the help of different NC &
CNC machines such as center lathes, vertical and horizontal boring &
milling machines. Asia’s largest vertical boring machine is installed here
and CNC horizontal boring milling machines from Skoda of
Czechoslovakia.
39
FIG.4 OVERSPEED AND VACCUM BALANCING TUNNEL
For balancing and over speed testing of rotors up to 320 tons in weight,
1800 mm in length and 6900 mm diameter under vacuum conditions of 1
Torr
40
then rotor is fitted inside this casing. After it this internal casing with rotor is
inserted into the external.
41
FIG.5 STEAM TURBINE CASING AND ROTORS IN ASSEMBLY AREA
2. Turning section- Same as the turning section in Bay-3, there are several small
Machine like lathes machines, milling, boring, grinding machines etc.
42
9. BLADE SHOP
Blade shop is an important shop of Block 3. Blades of all the stages of turbine are
made in this shop only. They have a variety of centre lathe and CNC machines to perform
the complete operation of blades. The designs of the blades are sent to the shop and the
Respective job is distributed to the operators. Operators perform their job in a fixed
interval of time.
9.1 TYPES OF BLADES
Basically the design of blades is classified according to the stages of turbine. The
size of LP TURBINE BLADES is generally greater than that of HP TURBINE BLADES.
At the first T1, T2, T3 & T4 kinds of blades were used, these were 2nd generation blades.
Then it was replaced by TX, BDS (for HP TURBINE) & F shaped blades. The most
modern blades are F & Z shaped blades.
43
9.2 OPERATIONS PERFORMED ON BLADES
Some of the important operations performed on blade manufacturing are:-
Milling
Blank Cutting
Grinding of both the surfaces
Cutting
Root milling
44
9.4 NEW BLADE SHOP
A new blade shop is being in operation, mostly 500mw turbine blades are
manufactured in this shop. This is a highly hi tech shop where complete manufacturing of
blades is done using single advanced CNC machines. Complete blades are finished using
modernized CNC machines. Some of the machines are:-
Pama CNC ram boring machine
Wotum horizontal machine with 6 axis CNC control
CNC shaping machine
45
10. CONCLUSION
Gone through rigorous one month training under the guidance of capable engineers
and workers of BHEL Haridwar in Block-3 “TURBINE MANUFACTURING” headed by
Senior Engineer of department Mr. A.K. KHUSHWAHA situated in Ranipur, Haridwar,
Uttarakhand.
The training was specified under the Turbine Manufacturing Department. Working
under the department I came to know about the basic grinding, scaling and machining
processes which was shown on heavy to medium machines. Duty lathes were planted in the
same line where the specified work was undertaken.
46