Professional Documents
Culture Documents
SI-3000KFE Series Low Current Consumption, Low Dropout Voltage Linear Regulator ICs
■Applications *1: A built-in input-overvoltage-protection circuit shuts down the output voltage at the Input Overvoltage Shutdown Voltage
of the electrical characteristics.
• Secondary stabilized power supply (local
power supply)
*1: VIN (max) and IO (max) are restricted by the relationship PD (max) = (VIN - VO) × IO = 16.6W.
*2: Refer to the Dropout Voltage parameter.
■Electrical Characteristics
Ratings
Parameter Symbol SI-3010KFE Unit
min. typ. max.
VADJ 0.98 1.00 1.02
Reference Voltage VIN=7V, IO=0.01A, V
Conditions
VC=2V, VO=5A
∆VOLINE 30
Line Regulation VIN=6 to 15V, IO=0.01A, mV
Conditions
VC=2V, VO=5A
∆VOLOAD 75
Load Regulation VIN=7V, IO=0 to 1A, VC=2V, mV
Conditions
VO=5A
VDIF 0.3
Conditions IO=0.5A, VC=2V, VO=5V
Dropout Voltage V
0.5
Conditions IO=1.0A, VC=2V, VO=5V
Iq 600
Quiescent Circuit Current µA
Conditions VIN=7V, IO=0A, VC=2V
Iq (OFF) 1
Circuit Current at Output OFF µA
Conditions VIN=7V, VC=0V
∆VO/∆Ta ±0.5
Temperature Coefficient of
VIN=7V, IO=0.01A, VC=2V, mV/ °C
Output Voltage Conditions
Tj=0 to 100°C, VO=2.5V
RREJ 75
Ripple Rejection VIN=7V, IO=0.1A, VC=2V, dB
Conditions
f=100 to 120Hz, V O=5V
Overcurrent Protection Starting IS1 1.1
A
Current*3 Conditions VIN=7V, VC=2V
VC, IH 2
Control Voltage (Output ON)*4 V
Conditions VIN=7V
VC, IL 0.8
Control Voltage (Output OFF) V
VC Conditions VIN=7V
Terminal IC, IH 40
Control Current (Output ON) µA
Conditions VIN=7V, VC=2V
IC, IL –5 0
Control Current (Output OFF) µA
Conditions VIN=7V, VC=0V
Input Overvoltage Shutdown VOVP 33
V
Voltage Conditions IO=0.01A
*3: IS1 is specified at the 5% drop point of output voltage VO on the condition that VIN = overcurrent protection starting current, IO = 10 mA.
*4: Output is OFF when the output control terminal VC is open. Each input level is equivalent to LS-TTL level. Therefore, the device can be driven directly by LS-TTLs.
*5: SI-3000KFE cannot be used in the following applications because the built-in foldback-type overcurrent protection may cause errors during start-up stage.
(1) Constant current load (2) Positive and negative power supply (3) Series-connected power supply (4) VO adjustment by raising ground voltage
32 ICs
SI-3000KFE Series
■Block Diagram
SI-3010KFE
VIN 2 4 VOUT
VC 1 5 ADJ
TSD
–
+ 3 GND
REF
●SI-3010KFE
D1*1
VIN VO
2 4 R1
+ +
VC GND ADJ
CIN Load
1 5 CO
3 R3
*2 R2
CIN: Input capacitor (22µF or larger) R1, R2: Output voltage setting resistors
CO: Output capacitor (47µF or larger) The output voltage can be adjusted by connecting R1 and R2 as shown
If a low ESR capacitor (such as a ceramic capacitor) is used above.
for the output capacitor, oscillation may occur. The recommended value for R2 is 10kΩ.
R1=(VO–VADJ)÷(VADJ/R2)
*1. D1: Reverse bias protection diode
This diode is required for protection against reverse *2: For SI-3010KFE, insert R3 in case of setting VO to VO ≤ 1.5V.
biasing between the input and output. The recommended value for R3 is 10kΩ.
(Sanken RU2Z is recommended.)
20
±0.2
Silicone Grease: 4.7
±0.2
10.16 ±0.2
With Infinite Heatsink G746 (Shin-Etsu Chemical) 2.54
±0.1
15
±0.2
5.4
200×200×2mm (2.3°C/W)
6.68
±0.2
15.87
10 100×100×2mm (5.2°C/W)
3.
φ
75×75×2mm (7.6°C/W) 2 ±0
. 2
A ±0.2
a. Part Number
SK 2.76
(17.9)
B b. Lot Number
5 C
c. Administer Number
(2)
±0.6
4 × p1.7
Ambient Temperature Ta (°C) +0.2 ±0.7
q Vc
0.5 –0.1 4.3
9.6
±0.2 w VIN
±0.7
8.2
e GND
r Vout
t ADJ
1 2 3 4 5
ICs 33