Professional Documents
Culture Documents
Samsung b1930n Monitor PDF
Samsung b1930n Monitor PDF
Model : B1930N
ODM Vendor : INNOLUX
[ Important ! ]
SVC P/G was separated per ODM Vendor for
downloading the MCU code and EDID file.
So SVC P/G should be used according to ODM vendor.
The 10th digit is ODM vendor code.
Example LS19HANKBUTRU
“U”: INNOLUX, “H”: QISTA, “G”: TPV
SERVICE Manual
1. Precautions
2. Product specifications
4. Troubleshooting
6. Wiring Diagram
7. Schematic Diagram
B1930N
Refer to the service manual in the GSPN (see the rear cover) for the more information.
1
GSPN (Global Service Partner Network)
Area Web Site
North America http://service.samsungportal.com
Latin America http://latin.samsungportal.com
CIS http://cis.samsungportal.com
Europe http://europe.samsungportal.com
China http://china.samsungportal.com
Asia http://asia.samsungportal.com
Mideast &Africa http://mea.samsungportal.com
This Service Manual is a property of Samsung Electronics Co.,Ltd. © 2009 Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable All rights reserved.
International and/or domestic law. Printed in Korea
P/N: TBD
56
3 Disassembly and Assembly
3-1 Disassembly
Caution: 1. Turn the monitor of before beginning the disassembly process.
2. When disassembling the monitor, do not use any metal tools except for the provided jig.
3. Disassemble the monitor carefully as directed in the following procedures.
11
4. 1) remove the screws on the right side for front
cover & back cover
12
7. Remove the SHIELD-LAMP.
Firstly hold chassis with one hand and bend
the shielding in the direction of the arrow as
shown in figure to unhook the shielding from
the chassis.
13
10. Remove the LENS from the front cover
14
13. Remove the 4 screws shown in the figure.
15
3 Disassembly and Assembly
Memo
16
4 Troubleshooting
4. Troubleshooting
4-1 Troubleshooting
1. Check the power state and the cable connections.
Check the connections of the power and signal cables.
Check whether the function button operates normally.
Notes:
2. If the screen is blank, check whether the power cord is connected correctly.
4. *Press the MENU button and hold down the” (Enter)”button for more than five (5) seconds to
return the monitor to default mode.
17
4 Troubleshooting
- W hen turning on the Power button after connecting the power cable, the LED
Symptom
at the front of the monitor does not operate.
- W hen turning on the Power button after connecting the power cable, the LED
at the front of the monitor does not operate.
- Check the IP board power fuse and the IP board output power.
Major checkpoints
- Check the connections for the IP board and the Main board inside the monitor.
- Check the Main board power part and also check whether there is any
abnormal output at any of the other output terminals.
ok
NG
Is DC 3.3V measured at pin 3 of
Check the circuits related to
Diagnostics U101
U101.
when pin 2 is DC 5V?
ok
NG
Is DC 1.8V measured at pin 3 of
Check the circuits related to
U102
U102.
when pin 2 is DC 3 3V?
ok
Caution Make sure to disconnect the power before working on the IP board.
18
4 Troubleshooting
Attached PDF
DC-DC
19
4 Troubleshooting
C aution M ake sure to disconnect the power before working on the IP board.
20
4 Troubleshooting
③HSYNC ④VSCIN
U105 Pin 16 17
LVDS Connector
CN103
① Is X101
oscillating correctly?
Attached PDF.
21
4 Troubleshooting
22
4 Troubleshooting
23
4 Troubleshooting
4-5 Adjustment
Entering: Menu Brightness 0 Contrast 0 Hold down the Enter button for five (5) seconds
24
4 Troubleshooting
1. Checking the MCU code version and checksum after entering SVC Mode.
3. Safe Mode
- When the input signal is higher than the supported frequency of the product, safe mode gives users some
time (one minute) to change the video card settings to the Recommended Mode settings.
25
4 Troubleshooting
After replacing the panel, move the panel item and hold down the Menu button for five (5) seconds.
The Ch. No is incremented by 1 and then both the on time and cycle are set to 0.
26
4 Troubleshooting
VGA Cable
Print Port
VGA
(D-Sub)
27
4 Troubleshooting
2) Write EDID: Click “Model” button to show the “Change Model” Window.
Then Select a Model which you want to write EDID (Detailed Model as Table 1)
28
4 Troubleshooting
29
4 Troubleshooting
2) Write EDID: It will auto write when you enter a S/N which is 15 chars, Pic as below:
30
4 Troubleshooting
31
4 Troubleshooting
VGA Cable Pa
rallel Cable
Print Port
VGA
(D-Sub)
32
4 Troubleshooting
2) Program process: Open the Attached Mstar ISP Tool for Samsung’s DDC Manager (Version
4.3.9.5 E) . Run it. Click ‘Connect ' button, It will select flash memory type automatically
33
4 Troubleshooting
2) Program process: Click `Read ' button, then select the MCU Code
34
4 Troubleshooting
2) Program process: Sometimes, if you program error, please try again with no worry
3) Finished
35
5. Exploded View & Part List
SB03A
Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-1
5. Exploded View & Part List
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-2
6 Wiring Diagram
6 Wiring Diagram
6-1 Wiring Diagram –Main Board
.
Panel
CN104 CN102
Keypad Control VGA Input
39
6 Wiring Diagram
6-2 Wiring Diagram – Main Board
LVDS Connector
(Connector to Panel
IP Board
Keypad Connector
(Connector to Keypad)
RGB Connector
(Connector to PC)
40
6 Wiring Diagram
Connector Functions
Supplies 5V from the power board to the main board and transmits the PWM output
from the power board to the inverter.
CN101 CN801
*When a problem occurs: The No Power and Blank Screen errors may occur.
Transmits the lamp current (6mA ~ 7mA) generated in the inverter to the lamp of the
CN501 ~ CN502 panel.
*When a problem occurs: The Blank Screen error may occur.
Transmits the LVDS signals from the main board to the panel.
CN105
*When a problem occurs: The Blank screen and No Power errors may occur.
6-4 Cables
Use LVDS 30P FFC cable
Code
Photo
41
6 Wiring Diagram
Memo
42