Professional Documents
Culture Documents
FROM:
AUGUST 15th 2011 TO FEBRUARY 12th 2012
SIWES REPORT
TABLE OF CONTENTS
|2
SIWES REPORT
|3
SIWES REPORT
LIST OF FIGURES
Figure 1.1: The Entrance of WRPC .................................................................................................................................................... 7
Figure 1.2: Organogram of WRPC ...................................................................................................................................................... 8
Figure 1.3: Organogram of Production Department ................................................................................................................. 9
Figure 2.1: Block Diagram of Reforming Plant ........................................................................................................................... 13
Figure 2.2: Block Diagram of NHU ................................................................................................................................................... 14
Figure 2.3: Cabin (left) and cylindrical (right) heater types ................................................................................................ 16
Figure 2.4: Block diagram of CRU process sections ................................................................................................................. 21
Figure 2.5: Process flow diagram of a semi-regenerative catalytic reformer unit..................................................... 23
Figure 2.6: Radial flow fixed bed reactors in actual reforming unit ................................................................................. 27
Figure 2.7: A typical distillation column ....................................................................................................................................... 30
Figure 2.8: Interiors of a fractionating column .......................................................................................................................... 31
Figure 2.9: Naphtha hydrotreating unit feed pump ................................................................................................................. 32
Figure 2.10: Make up hydrogen gas compressor ...................................................................................................................... 33
Figure 2.11: Heat Exchanger .............................................................................................................................................................. 34
Figure 2.12: Tube Bundle .................................................................................................................................................................... 35
Figure 2.13: Air Coolers ........................................................................................................................................................................ 36
Figure 2.14: Pneumatic Control Valve ........................................................................................................................................... 37
Figure 2.15: Horizontal Separator Drum ...................................................................................................................................... 38
Figure 2.16: Fire Triangle .................................................................................................................................................................... 42
LIST OF TABLES
Table 1.1: WRPC DESIGN PRODUCT SCALE 11
Table 2.1: NHU COMBINED FEED PREAHEATER 15
Table 2.2: REACTOR FEED HEATER PROPERTIES 16
Table 2.3: HYDRODESULPHURISATION REACTOR 17
Table 2.4: NHU PREFLASH COOLERS 18
Table 2.5: COOLED EFFLUENT H.P SEPARATOR 18
Table 2.6: H.P SEPARATOR EFFLUENT COOLER 19
Table 2.7: COOLED EFFLENT L.P SEPARATOR 19
Table 2.8: NHU STRIPPER COLUMN 19
Table 2.9: NHU STRIPPER REFLUX DRUM 20
|4
SIWES REPORT
CHAPTER 1
1 INTRODUCTION
The student’s SIWES program is a skill-acquisition program designed for 300 Level and 400 Level students
of most tertiary institutions as a complementary program to the theoretical education and laboratory
practices engaged in by students in tertiary institutions, which by industrial standard are inadequate to
serve the practical needs of the industries. The practices are idealistic and therefore necessitate that the
student be exposed to actual life practice, which is a far departure from academic institutional class and
laboratory practice.
The official Gazette of the Federal Republic of Nigeria made it clear that, the Supreme Military Council then
headed by General Yakubu Gowon in the year 1972 promulgated decree No.47 to indigenize the Nigeria
Economic Sector. On the 31st of March 1974, the decree came into effect with its core aim of reducing the
dominance of foreigners in the Nigerian economy, and accompanied by a systematic integration of locally
oriented skilled manpower into the economy.
The indigenization decree established many bodies which were charged with different responsibilities to
make the nations dream a reality. Among them include:
The Industrial Training Fund (ITF) was charged with the responsibility of training low and middle level
manpower for sustainable industrialization.
However, when the Federal Government observed that the training of students who are still in school
would be easier and cheaper, and that such training would make them more competent to assume any
responsibility to their related field of study, a scheme known as Students Industrial Work Experience
Scheme was established under ITF. This body was mandated to liaise with all the relevant agencies like
National Universities Commission (NUC), National Board for Technical Education (NBTE) to ensure proper
training of undergraduate students. The Students Industrial Work Experience Scheme (SIWES) was
established in 1974, since the inception of SIWES, it has been a partial fulfillment of the academic program.
SIWES is devised by National University Commission (NUC) as a skill training program that will bridge the
|5
SIWES REPORT
long gap that demarcates theory from practical in science and technology and other related courses in
Nigeria Universities.
Building the students ability to work with equipment they do not have access to in school.
Providing an opportunity for students to apply the theoretical knowledge acquired in the
classroom to a real practical work situation.
Preparing the student against the real challenge they would encounter in their field of
specialization after graduation.
The industries/organizations get involved in training the manpower they need; thereby preparing
the trainee for employment opportunity after graduation.
Participation in Industrial Training is a well-known educational strategy. Classroom studies are integrated
with learning through hands-on work experiences in a field related to the student’s academic major and
career goals. Successful internships foster an experiential learning process that not only promotes career
preparation but provides opportunities for learners to develop skills necessary to become leaders in their
chosen professions.
Participation in SIWES has become a necessary pre-condition for the award of Diploma and Degree
certificates in specific disciplines in most institutions of higher learning in the country, in accordance with
the education policy of government.
Operators: The ITF; the coordinating agencies (NUC, NCCE, NBTE), employers of labor and the
institutions.
|6
SIWES REPORT
Warri refining and petrochemical company is a leading company in the oil and gas sector in Nigeria. The
period of my industrial attachment was from August 2011 to February 2012.
The naphtha hydro-treating and catalytic reforming unit under the production department is the section I
was deployed to, for the duration of my attachment and as hence experienced the production of reformate,
treated naphtha, gasoline(petrol) and other by-products such as hydrogen gas, propane, butane and other
light hydrocarbon ends e. t. c. Also, the unit produces medium pressure steam used to drive steam turbine
pumps and compressors.
|7
SIWES REPORT
of 100,000 barrels per stream day of crude oil. It was de-bottle necked in 1987 to 125,000 barrels per
stream day (17,000metric tonnes per day).
The fuel plants were designed to process the CHEVRON’S ESCRAVOS crude oil (sweet crude) and SHELL’S
UGHELLI QUALITY CONTROL CENTRE (UQCC) crude oil (sour crude).
The petrochemical plants (polypropylene and carbon black) which were built to optimize the refinery
were commissioned in March 1988. An HYDRO-FLOURIC alkylation unit was also added to the refinery the
same year.
|8
SIWES REPORT
Vacuum Distillation Unit: This unit of the refining crude oil utilizes negative pressure to distil
atmosphere bottoms into gas oils and asphalt.
Desalter Unit: Washes out salt from the crude oil before it enters the atmosphere distillation unit.
|9
SIWES REPORT
Kerosene Hydro-treating Unit: The purpose of this unit is to reduce the sulphur and nitrogen content of
the feed and to improve combustion characteristics of transportation fuels.
Naphtha Hydro-treating: Utilizes a cobalt molybdenum catalyst to remove metallic and non metallic
impurities found in the reformer feed.
Catalytic Reforming Unit: This unit is used to convert naphtha boiling range molecules into higher octane
reformate. Reformates has a higher content of aromatics and cyclic hydrocarbons. It also generates the
hydrogen utilized in naphtha hydro treating unit to remove impurities in the reformer feed.
Fluid Catalytic Cracking Unit: The basic purpose of this plant in the refinery is to convert heavy gas oil
which is of less market value into lighter, more valuable hydrocarbons. As the name implies, it uses a fine
powdery catalysts which under the action of fluidization medium such as air, hydrocarbon vapor or steam
behaves like a liquid. The unit is designed to process 26,000bpsd of gas oil feedstock into high valued
products like gasoline and LPG.
HF-Alkylation Unit: This is a process unit used to convert light olefins (e. g propylene, butylenes)
produced in catalytic crackers into a more highly valued gasoline component. Alkylate is one of the best
gasoline blending components produced in the refinery because of its high octane rating and lower vapor
pressure. It is usually referred to as a five star gasoline.
Waste Water Unit: This unit is involved in both collection and treatment of sour water and sludge
received from other units using treatment system like the API separator, dissolved air floatation, activation
sludge bioreactors and some other methods to make such water suitable for re-use or disposal.
A blend on ethylene could be added in a secondary reactor to obtain a co-polymer which has enhanced
properties. The PP plant in WRPC is designed to produce 35,000 MT per year of Polypropylene pellets.
Carbon Black Plant: This plant is designed to produce 18,000 Metric-tonnes per day and is capable of
producing several grades of hard black. The plant is based on the Philips’ technology of regulated
incomplete combustion of decanted oil in horizontal tubular reactor. Carbon black is made of 90-97% very
fine elemental carbon particles. The remaining are organic compounds (carboxylic, phenols,
hydroquinone, lactones groups) strongly absorbed or chemically bounded to the surface layers. The
particle sizes as well as the non-carbon percentage vary in accordance with the different production
methods. Carbon black is used in the manufacture of inks, paints, conveyor belts, foot wears, and other
commodities.
| 10
SIWES REPORT
Auxiliary Units: These units are designed and built to provide various input material and services to the
processing units. They are not involved in the direct conversion of crude (raw material) to finished
products. They include:
At maximum design capacity, the refinery is configured to produce these products at the following rates:
WRPC is primarily involved in the processing of crude oil into finished and semi-finished products. Its
products are sold in the Nigerian local market as well as overseas. The high quality of its products favors
her significantly in both local and foreign markets.
| 11
SIWES REPORT
Kerosene(Domestic/Aviation)
Fuel Oil
E.t.c
WRPC also create opportunities for students and young school leavers to gain industrial knowledge by
giving them placement for SIWES and NYSC programs respectively.
Research, human resource development and capacity building are performed by the company. These
functions are achieved through equipped library, sponsoring its staff to local and foreign training and
seminars and installation of modem laboratory facilities.
| 12
SIWES REPORT
CHAPTER 2
2.1 PREAMBLE
The reforming unit is quite a collection of process units. However the Process description can be divided
into 3 basic sub units namely:
The CRU and NHU are both designed to process 2035.9 Metric Tons per stream day or 16,600 bpsd of
Heavy Naphtha. The installed capacity of the KHU is 8,500 bpsd.
These basic Units shall be discussed into sections as regards this chapter.
To properly eliminate the impurities, the feed undergoes series of processes namely:
| 13
SIWES REPORT
The Heavy Naphtha feed is then mixed with hydrogen rich make up gas coming from the reforming unit before
it is being sent to the preheater. The combined feed is preheated in a two parallel heat exchangers 11-E-01
A/B.
The purpose of the preheater is to pre-heat the combined feed to the required heater inlet temperature to
prevent frying before it is properly heated to a temperature of about 300 degree centigrade. The combined
feed enters the heat exchanger through the inlet of the shell side and passes through the tube bundles before
finally leaving through the outlet of the shell side. Each heat exchanger contains hot heavy naphtha (HN) with
slurry respectively which helps to heat up the feed to about 250°c-260°c before it enters the heater.
| 14
SIWES REPORT
2.2.2 HEATING
The heater in the Naphtha Hydrotreating Unit is a cabin/cathedral heater (11-H-01) which operates by natural
draft system which is adjusted by a manual stack damper for the regulation of air into the heater chamber. The
preheated feed enters the furnace (heater) chamber. The heater is equipped with six burners which utilizes
fuel gas, fuel oil, pilot gas, and atomizing steam as its source of heat for proper combustion of the preheated
feed in the tubes. The feed first enters the tubes in the convection zone (top) of the furnace where it is heated
by the fuel gases before it enters the tubes in the radiation zone (bottom) for proper heating.
The purpose of the heating process is to properly heat up the feed to the required reactor inlet temperature of
about 300°c.
| 15
SIWES REPORT
| 16
SIWES REPORT
In the reactions, the non-metallic impurities {oxygen, sulphur, and nitrogen} are eliminated in the form of
water (H2O), hydrogen sulphide (H2S) and ammonia (NH2) respectively. The chemical reaction takes place
at a temperature of 300°c
Size Mm 2400/4620
2.2.4 COOLING
The cooling process is performed by three cooler heat exchangers. The purpose of the coolers is to reduce
the temperature of the reactor effluent up to the required inlet temperature for the high pressure
separator drum 11-D-02. Therefore, the reactor effluent is cooled in the heat exchanger 11-E-01, air cooler
11-A-01 and trim cooler 11-E-02.
| 17
SIWES REPORT
Firstly, the product from the reactor enters directly to 11-E-01, and then to 11-A-01 and finally gets cooled in
11-E-02.
2.2.5 FLASHING
Flashing in the Naphtha hydrotreating unit is done in the high pressure separator drum and the low pressure
separator drums respectively. The primary function of the high pressure separator drum is for the separation
of the liquid hydrocarbon from the hydrogen/hydrogen sulphide/ammonia gas combination. Also, the
function of the low pressure separator drum is for the separation of liquefied petroleum gases(LPG) prior to
sending the hydrocarbon liquids to fractionation.
Design Temperature °C 55
Thus, the cooled effluent from the exchanger 11-E-02 is flashed in the HP separator drum. The level in the HP
separator drum is controlled by a level regulator and controller (11-LRC-1).After the level controlvalve, the
separator liquid is mixed with the vapour distillates from the stripper overhead drum (11-D-03) and the
reformer stabilizer overhead drum (12-D-03) so as to permit maximum recovery of C3 and C4 for LPG
production.
The combined vapour and liquid stream is then cooled in the water cooler (11-E-03) after which it is flashed
into the low pressure separator drum.
| 18
SIWES REPORT
LP SEPARATOR 11-D-02
Design Temperature °C 55
The vapour phase is sent to fuel gas under pressure control (11-PRC-02) while the separator liquid is pumped
to the stripper column.
2.2.6 STRIPPING
The stripping process is performed in the fractionating column which utilizes the principle of distillation. The
purpose of the stripper 11-C-01is to remove Hydrogen Sulphide (H2S), Water (H2O), and Light hydrocarbon
ends from the treated naphtha before being sent to the reforming unit.
No of Trays 31
The feed flow rate to the stripper is controlled by a flow regulator and controller (11-FRC-2) in cascade with a
level regulator and controller (11-LRC-2) which controls the level on 11-D-02. The feed to the stripper is
preheated in a two parallel heat exchangers (11-E-04 A/B). Also the stripper bottoms are cooled by heat
exchange in 11-E-04 A/B and then sent as H2S free feed to the reforming unit.
Part of the treated naphtha is sent to storage. The amount of treated naphtha sent to storage tank is measured
and recorded by the totalizing flow meter 11-FT-51.
| 19
SIWES REPORT
It is desirable to maintain a constant feed flow rate to the Catalytic Reforming Unit to avoid perturbations on
the reactions. Therefore, the feed flow rate to the reforming unit is controlled by 12-FRC-1 and 12-FRC-2.
The stripper overhead vapoursare partially condensed in air cooler 11-A-02and trim cooler 11-E-05and finally
separated into liquid and vapour phases in the reflux drum 11-D-03.
Design Temperature °C 55
The Vapour phase from 11-D-03 is recycled for LPG recovery(or is sent to fuel gas system) .The Liquid phase is
sent partially as reflux to the top of the stripper column, it is also sent partially as LPG to the gas plant unit 14.
The quantity of LPG is measured and totalized by flow meter 11-FT-52. The water eventually entrained in the
naphtha charged to the pretreating unit is separated by decantation in 11-D-03 and removed from the boot
attached to the stripper reflux drum and sent to Sour Water Stripper 202-C-01.
Stripper column most important operating variables are: temperature profile along the column, pressure and
products composition. These variables directly influence each other and depend on other variables such as
reflux rate and reboiler temperature.
| 20
SIWES REPORT
There are many chemical reactions that occur in the catalytic reforming process, all of which occur in the
presence of a catalyst and a high partial pressure of hydrogen. Depending upon the type or version of
catalytic reforming used as well as the desired reaction severity, the reaction conditions range from
temperatures of about 495 to 525 °C and from pressures of about 5 to 45 atm.
The commonly used catalytic reforming catalysts contain noble metals such as platinum and/or rhenium,
which are very susceptible to poisoningthe nitrogen compounds.
1: The dehydrogenation of naphthenes to convert them into aromatics as exemplified in the conversion
methylcyclohexane (a naphthene) to toluene (an aromatic), as shown below:
2: The isomerisation of normal paraffin to isoparaffinsas exemplified in the conversion of normal octane to
2, 5-Dimethylhexane (an isoparaffin), as shown below:
| 21
SIWES REPORT
4: The hydrocracking of paraffin’s into smaller molecules as exemplified by the cracking of normal
heptanes into isopentane and ethane, as shown below:
The hydrocracking of paraffin’s is the only one of the above four major reforming reactions that consumes
hydrogen. The isomerisation of normal paraffin’s does not consume or produce hydrogen. However, both
the dehydrogenation of naphthenes and the dehydrocyclization of paraffin’s produce hydrogen. The
overall net production of hydrogen in the catalytic reforming of petroleum naphtha’s ranges from about 50
to 200 cubic meters of hydrogen gas (at 0 °C and 1 atm) per cubic meter of liquid naphtha feedstock.
The process flow diagram below depicts a typical semi-regenerative catalytic reforming unit.
| 22
SIWES REPORT
The liquid feed (at the bottom left in the diagram) is pumped up to the reaction pressure (5 to 45 atm) and
is joined by a stream of hydrogen-rich recycle gas. The resulting liquid-gas mixture is preheated by flowing
through a heat exchanger. The preheated feed mixture is then totally vaporized and heated to the reaction
temperature (495 to 520 °C) before the vaporized reactants enter the first reactor. As the vaporized
reactants flow through the fixed bed of catalyst in the reactor, the major reaction is the dehydrogenation of
naphthenes, to aromatics (as described earlier herein) which is highly endothermic and results in a large
temperature decrease between the inlet and outlet of the reactor. To maintain the required reaction
temperature and the rate of reaction, the vaporized stream is reheated in the second fired heater before it
flows through the second reactor. The temperature again decreases across the second reactor and the
vaporized stream must again be reheated in the third fired heater before it flows through the third reactor.
As the vaporized stream proceeds through the three reactors, the reaction rates decrease and the reactors
therefore become larger. At the same time, the amount of reheat required between the reactors becomes
smaller. Usually, three reactors are all that is required to provide the desired performance of the catalytic
reforming unit.
Some installations use three separate fired heaters as shown in the schematic diagram and some
installations use a single fired heater with three separate heating coils.
| 23
SIWES REPORT
The hot reaction products from the third reactor are partially cooled by flowing through the heat
exchanger where the feed to the first reactor is preheated and then flow through a water-cooled heat
exchanger before flowing through the pressure controller (PC) into the gas separator.
Most of the hydrogen-rich gas from the gas separator vessel returns to the suction of the recycle hydrogen
gas compressor and the net production of hydrogen-rich gas from the reforming reactions is exported for
use in the other refinery processes that consume hydrogen (such as hydrodesulphurisation units and/or a
The liquid from the gas separator vessel is routed into a fractionating column commonly called a stabilizer.
The overhead off gas product from the stabilizer contains the by product methane, ethane, propane and
butane gases produced by the hydro cracking reactions as explained in the above discussion of the reaction
chemistry of a catalytic reformer, and it may also contain some small amount of hydrogen. That off gas is
routed to the refinery's central gas processing plant for removal and recovery of propane and butane. The
residual gas after such processing becomes part of the refinery's fuel gas system.
The bottoms product from the stabilizer is the high-octane liquid reformate that will become a component
of the refinery's product gasoline.The reactions are governed by kinetics and thermodynamic rules which
means that they tend towards a thermodynamic equilibrium at varying rates.Usually, the optimum
equilibrium that can be obtained will depend upon the operating conditions that are temperature,
pressure, e.t.c. The reaction rates with which this equilibrium is reached is mainly a function of the quality
and the properties of the catalyst.The extent to which a catalyst favours one or the other reaction and thus
influences the final equilibrium is called the selectivity.
The chemical reactions described above are those that the reforming catalyst favours with respect to
other.Due to these decreasing rates, it is possible to localize the reaction in the following manner:
1st reactor
o Dehydrogenation
o Isomerisation
2nd reactor
o Dehydrogenation
o Isomerisation
o Hydrocracking
o Dehydrocyclisation
3rd reactor
o Isomerisation
| 24
SIWES REPORT
o Hydrocracking
o Dehydrocyclisation
4th reactor
o Hydrocracking
o Dehydrocyclisation
In every reactor, there is always a catalyst which helps to speed up the reaction. Most catalytic reforming
catalysts contain platinum or rhenium on a silica or silica-alumina support base, and some contain both
platinum and rhenium. Fresh catalyst ischlorided (chlorinated) prior to use.
The noble metals (platinum and rhenium) are considered to be catalytic sites for the dehydrogenation
reactions and the chlorinated alumina provides the acid sites needed for isomerisation, cyclization and
hydrocracking reactions.
The activity (i.e., effectiveness) of the catalyst in a semi-regenerative catalytic reformer is reduced over
time during operation bycarbonaceous coke deposition and chloride loss. The activity of the catalyst can be
periodically regenerated or restored by in situ high temperature oxidation of the coke followed by
chlorination. As stated earlier herein, semi-regenerative catalytic reformers are regenerated about once
per 6 to 24 months.
Treated naphtha coming hot from the bottom of hydrotreater stripper 11-C-01 is directly charged to the
reforming unit through pump 12-P-01 A/B.
The feed is then mixed with recycle gas been compressed by compressor 12-K-01.
The combined feed from the heat exchangers is sent to the heater 12-H-06 and then it is sent to the 12-H-
01.
After heating, the combined feed enters the first reactor 12-R-01.
Due to the endothermicity of the reactions each reactor effluent must be heated by means of 3 fired
heaters 12-H-02, 12-H-03 and 12-H-03 and 12-H-04 situation before 12-R-02, 12-R-03 and 12-R-04
respectively.
The effluent from the fourth reactor is cooled through 12-E-01 A/B, it is further cooled in air cooler 12-A-
01 and trim cooler 12-E-02 before it is flashed in the first separator 12-D-01.
| 25
SIWES REPORT
The major part of the vapour from reforming L.P. separator 12-D-01 is split into two streams which are
compressed by compressor 12-K-01 and 12-K-02 A/B/C respectively.
As mentioned earlier one stream of the vapour phase from 12-D-01 is compressed by compressor 12-K-01
and sent, as recycle gas, to the reaction section.
The other stream passes through the K.O drum 12-D-04 and is compressed by 12-K-02 A/B/C and mixed
with the liquid phase from 12-D-01 which is pumped by 12-P-02 A/B to the required pressure.
The combined flow is cooled the trim cooler 12-E-03 and flashed in the H.P. separator drum 12-D-02.The
vapour phase from 12-D-O2 is sent to battery limit to kero hydrogenation (unit 13) and to make up for
naphtha hydrotreating (unit 11), while the liquid phase is sent to the stabilizer column.
Before entering the stabilizer column, the field is pre-heated in exchanger 12-E-04 A/B by the stabilizer
bottom product.
2.3.2 REACTORS
A reactor is a process vessel in which chemical reactions (catalyzed or non-catalyzed) the place during a
chemical conversion type of process. The four reactors installed in actual reforming unit are radial-flow-
fixed bed reactor. This reactor is a variance of the down flow fixed-bed reactor.
Again, the feedstock enters the top of the reactor but instead of flowing downward through the catalyst
bed, the feedstock is encouraged to flow through the bed in a radial direction and then out through the bed
in a radial direction and then out through the base of the reactor.
| 26
SIWES REPORT
Figure 2.6: Radial flow fixed bed reactors in actual reforming unit
2.3.3 HEATING
Description
After passage through 12-E-01 A/B the feed is sent to the feed preheated 12-H-06 and then it is sent to
the first reforming heater 12-H-01 before entering 12-R-01(first reactor).
Due to the endothermicity of the reactions each reactor effluent must be heated by means of 3 fired
heaters 12-H-02,12-H-03,12-H-04 situated before 12-R-02,12-R-03 and 12-R-04 respectively.
The required temperature of each reactor inlet is controlled by TRC situated at the outlet of each heater.
12-H-06 description
The combined feed is controlled into the furnace 12-H-06 radiant zone. (Six burners)
12-H-01 Description
The combined feed is introduced into the furnace 12-H-01 radiant zone.(twelve burner
12-H-02 description
The effluent from the first reactor is introduced into the furnace 12-H-02 radiant zone (twelve burners)
| 27
SIWES REPORT
12-H-03 description
The effluent from the second reactor is introduced into the furnace 12-H-03 radiant zone. (Eighteen
burners)
12-H-04 description
The effluent from the third reactor is introduced into the furnace 12-H-04 radiant zone (Six burners).
It should be noted that in each of the heaters thermocouple are installed to show:
2. Flue gas temperature in the convective zone and stack and oxygen analyzer recorder is installed in the
convective zone.
The burners are of mixed type, fuel gas, fuel oil and atomized steam.
1. Reactor temperature
2. Reactor pressure
3. Reactor space – velocity
4. Hydrogen / hydrocarbons mole ratio
5. Feed composition
6. Catalyst activity.
All of these variables affect the product quality and the economics of operations. The first three of these
variables, listed in order of the effect on product quality, are usually under the direct control of the unit
operator, as is possible for the particular unit and type of operation. The fourth may be controlled by the
operator in some cases. It is frequently fixed during the design of the plant on the basis of a known charger
stock and severity of operations, or is fixed during plant operation by other considerations as discussed
later.
The fifth variable, charge – stock composition, is normally not at the discretion of the operator. This is true
especially when the charge stock is a single stream from an upstream limit. If streams from multiple
sources are charged, the operator has some range of control over the final charge – stock composition.
Catalyst activity, the last variable depends upon the catalyst and the previous catalyst history. Severity is a
combination of temperature, pressure and space velocity.
| 28
SIWES REPORT
As in all process, control of reformers for desired results is achieved by control of the process variables.
Reactor temperature is probably the most important variable in the control of catalyst reformer. In a
particular unit, pressure and space velocity are usually fixed by basic operational considerations as
discussed later. This leaves temperature as the controlling factor in severity control. Reactor temperature
is controlled at the reactor inlet (furnace outlet).
| 29
SIWES REPORT
It should be noted that the amount of heat entering the column from the reboiler and with the feed must equal
the amount of heat removed by the condenser and with the products. The heat (temperature) entering the
column is a crucial operating parameter, addition of excess or
insufficient heat to the column can lead to entrainment, flooding e.t.c. The fractionating column usually
separates a feed stream into one distillate fraction. However, the columns have outlets at intervals up the
column so that multiple products having different boiling ranges may be withdrawn from the column distilling
a multi-component feed stream. The "lightest" products with the lowest boiling points exit from the top of the
columns and the "heaviest" products with the highest boiling points exit from the bottom.
Fractionating columns in the refining plants uses external reflux to achieve better separation of products
thereby maintaining the temperature profile at the top of the column. Reflux refers to the condensed overhead
| 30
SIWES REPORT
liquid product that returns to the upper part of the column (after the overhead vapour has been condensed by
a heat exchanger and separated in a reflux) drum.
Inside the column, the downflowing reflux liquid (downcomers) provides cooling and condensation of
upflowing vapours thereby increasing the efficacy of the distillation tower. Bubble cap "trays" are one of the
types of physical devices, which are used to provide good contact between the upflowing vapors and the
downflowing liquids inside the fractionating column. The efficiency of a tray or plate is typically lower than
that of a theoretical 100% efficient equilibrium stage. Hence, a fractionating column almost always needs
more actual, physical trays than the required number of theoretical stages.
2.5.2 Pumps
These are mechanical devices used to transport liquids to a required destination especially through long
distances. They do so by increasing the pressure of such liquids. Pumps are composed of various parts
such as the suction line, discharge line, pump casing, impellers (rotor), drive shaft, etc. The pumps in the
reforming plant are either driven by an electric motor or a steam turbine. Attached to the discharge line is
a check valve to prevent back flow of fluids. PM/PT is the acronym for pumps in the plant meaning pump
motor/pump turbine respectively, depending on it driving force. There are of various types namely:
| 31
SIWES REPORT
centrifugal pumps, reciprocating pumps, submersible pumps, positive displacement pumps, screw pumps
etc.
However, WRPC reforming plant only utilizes the centrifugal and reciprocating pumps for its operations.
2.5.3 Compressors
Compressors are machines used for compressing air or other gases. There are two main types of compressor
in the reforming plant namely:
Centrifugal compressors which are dynamic machines that increase the pressure of a fluid (air or gas)
traversing it by applying inertia forces (acceleration turning) to the fluid. For example 12-K-02
A/B/C in the catalytic reforming unit (which compresses H 2 for recycling) and 112-K-01 in the
naphtha hydrotreating unit (for the hydrogen bottles in batches).
| 32
SIWES REPORT
Reciprocating compressors which achieve the desired compression of gases by means of a piston
moving back and front in a cylinder. They are especially used to obtain very high pressures but
cannot reach high flow rates because of their low speed. For example 12-KT-01 in the catalytic
reforming unit (which also compresses H2 and sent as recycle gas to the reaction section).
Cooling a liquid.
Heating a liquid.
Condensing a gas.
Evaporating a liquid.
Re-boiling a liquid.
a. Coolers.
| 33
SIWES REPORT
b. Heaters.
c. Condensers.
d. Evaporators.
e. Re-boilers.
Heat exchangers are usually divided into two sections (tube and shell).They use a conducting element which is
usually in the form of a tube or plate to separate two fluids such that one can transfer thermal energy to the
other without inter-mixing both fluids. The hotter products that needs to be cooled enters through the tube
inlet and leaves through the tube outlet, while the colder products that needs to be heated enters through the
shell inlet and leaves through the shell outlet of the heat exchanger.
| 34
SIWES REPORT
These exchangers could be either of the following depending on the physical structure and function; tube and
shell type, fixed tube, floating head, kettle type and u-tube heat exchanger. The heat exchangers are equipped
with series of baffles that increases the residence time by delaying flow, thereby allowing for better
cooling/heating. Heat exchangers in the unit are assigned the acronym E. An example is 12-E-04.
| 35
SIWES REPORT
| 36
SIWES REPORT
Ball valves which are good for on/off control. They are usually installed along a water line.
Gate valves which are mainly used for isolation (i.e. to fully open or close). It is otherwise known for
on/off control.
Globe valves or throttling valves which is good for controlling and regulating flow.
Check valves or non-return valve which allows the fluid to flow only in one direction (0ne directional
valve). It is usually installed in the discharge line of pumps and compressors.
Plug valves for on/off control.
Needle valves installed along an instrument line.
Safety valve or pressure relief valve operated automatically at a set differential pressure to correct a
potentially dangerous situation, typically over-pressure.
Butterfly valve for control of gas flow.
| 37
SIWES REPORT
Flooding is the excessive accumulation of liquid inside the fractionating column which could be caused by;
low liquid flow rates (where most of the liquid on the tray is in the form of droplet), tray pressure drop,
liquid height on the tray, friction under the down comer and excessive feed charging, etc.
Solution
Flooding can be avoided by the use of control system to control process or operational variables.
Controllers to be used are:
| 38
SIWES REPORT
Water can cause severe operational problems in services which are not meant to handle it. Most problems
occur when the fractionating column separates water insoluble material such as hydrocarbons. If a slug of
cold water is suddenly dumped into a hot column containing hydrocarbons; the water will be vaporized.
This vapor is caused by the presence of the liquid phase simultaneously. The water phase will attempt to
exert is own vapor pressure and will therefore rapidly vaporize. Due to its low molecular weight, water
will expand to above 1000 to 2000 times the liquid volume upon vaporization close to atmospheric
pressure. This may generate a rapid and impulsive pressure surge. Such a pressure surge can dislodge or
damage trays, packing lines, support e t c.
Solution
C. Dirty streams
The separator liquid(stripper feed) can be polluted by dirty vapor from flash zone. Dirty streams can be
caused by
Excessive water content which increases the vapor velocity in the flash zone of the column.
Insufficient reflux to keep the lower trays wet.
A low temperature at the heater (stripper reboiler) outlet causes insufficient vaporization in the
flash zone, and sufficient treated naphtha products may not be obtained.
Very high transfer temperature at the heater outlet causes the column to be subjected to excess
thermal duty input and increases the quantity of over flashed liquid.
Solution
o Quality of stripper used must satisfy the operational conditions (temperature and pressure) to
attain optimal stripping operation.
o The amount of product removed from the column should be monitored by panel operators to
avoid rupturing of trays.
| 39
SIWES REPORT
o Temperature of feed from the outlet of the heater should be monitored. Then if any deviation from
its set point, other process variable should be altered to achieve the desired operational
temperature.
c. Cavitation
Cavitation is a phenomenon which occurs when there is an invasion of air (gas) in a pump thereby causing
an impeachment in the flow. This results to a jerk or an abnormal vibration (hammering) of the pump.
From continuum theory: “fluid is said to be in a continuous phase devoid of void” that is to say for a
moving fluid there ought to be no void spaces. Thus this phenomenon is likely to occur when bubbles of
vapor or pockets of air forms in the pump casing as a result of:
Insufficient feed
Overheating
Plugged suction filter
Sudden change in magnitude of the velocity of fluid
Misalignment of spacer coupling
Invasion of air into the liquid stream of the pump
Solution
d. Surging
This has to do with a sudden/major increase in the noise of the compressor usually accompanied by a
powerful forward or backward movement. Surging can be caused by
| 40
SIWES REPORT
Solution
o Gas flow rates should be kept constant by proper monitoring of the flow regulator and controller.
o Barring of gear should be properly conducted before starting up the compressors during shut
down
o The Oil level in the frames and cylinders of the compressors should be properly monitored to
avoid shortage of oil.
e. Incomplete Combustion
Incomplete combustion is a situation whereby coke deposited on the catalyst is burnt off with air and CO
(which constitutes a major health hazard to man) instead of CO2. Incomplete combustion is as a result of:
Solution
1. Accidental Hazards
Slips and fall by floors made slippery by oil, grease, aqueous solutions and solvents.
| 41
SIWES REPORT
2. Physical Hazards
Hazards due to mishandling of equipment such as valve key (openers), weight lifting
devices(such as cranes for lifting lube/seal oil drums) during tank loading.
3. Chemical Hazards
4. Explosive risk
In order for gas to ignite there must be an ignition source, typically a spark (or flame or hot surface) and
oxygen. For ignition to take place, the concentration of gas or vapor in air must be at a level such that the
fuel and oxygen can react chemically. The degree of the explosion depends on the fuel and its
concentration in the atmosphere. The relationship between fuel/air/ignition is illustrated in the fire
triangle below.
Therefore, explosion due to unsafe practices could occur leaving the plant personnel critically injured.
| 42
SIWES REPORT
The safety measures necessary to be observed in the reforming plant can never be over emphasized. Since
the production plant is an area highly exposed to hazards, plant operators are regularly checked by the
health safety and environment (HSE) officers to ensure that personnel in the plant are fully kitted with
their PPE’S (personal protective equipment) in order to maintain a safe working environment.
All operators in the plant should always put on their personal protective equipment (coverall, eye
goggles, ear muffs/plugs, nose mask, hand gloves, safety shoes and helmet) in order to guide
themselves from potential threats in the plant.
If an operation represents a potential safety or health threat, every effort should be made to plan a
safe way to complete the task in a safe manner.
Shortcuts in the plant is highly prohibited, therefore all procedures must be duly followed.
If an operator observes any unsafe or unprotected exposure which may pose a potential threat to
their safety and health, he or she must inform the chief operator or the superintendent
immediately for corrective measures.
| 43
SIWES REPORT
temperature of the products in the tubes and more heat is wasted up the chimney stack. This leads to higher
fuel consumption and poor heating.
The soot blowers in the reforming unit are usually operated automatically from the control room with the aid
of the remotely controlled motors. It is sometimes operated manually if there’s a failure on the part of the
controlling motors. The soot which is removed from the furnace tubes is blown out with the flue gases and
ejected into the outside air through the chimney stack.
those limits required to keep a correct balance between the metallic and acidic functions of the catalyst.
Beyond those limits, the liquid yield and useful life of the catalyst decrease to unacceptable values. The remedy
for hyperactivity of the catalyst consists of injecting small regulated doses of water in the feed.
Finally, for a perfect balance to be maintained, suitable proportions of water and the chlorinating agent (PDC)
is usually injected on the injection tanks (12-TK-13 and 12-TK-14) before being charged to the reforming
reactors.
The phosphate solution used in performing this operation is called tri-sodium phosphate with a chemical
formula of Na3PO4
2.9.4 Regeneration
The coke deposit acts on catalyst activity by reducing the surface of contact. During operation, carbon will
gradually accumulate on the catalyst. The aim of the regeneration operation is to remove this coke by
combustion and retain its initial activity.
The operation is performed with the unit out of service and consists of three phases which must be conducted
under rigidly controlled conditions:
| 44
SIWES REPORT
CHAPTER 3
Students find it difficult to secure an appointment from any organization. At times most students even go
to where they never wanted instead of staying at home.
2. Problem of adaptation
One challenging experience I personally encountered was trying to adapt to the shift operation being
practiced at WRPC (production department). It was really challenging because we were been made to
work from 7a.m to 7p.m for two days and another 7p.m to 7a.m for another two days consecutively, we
were made to stay awake all night till the next morning.
The attitude of some company staffs towards IT students is something that can never be overemphasized,
as some staffs go as far as seeing the IT students as messengers (errand boys or girls) instead of teaching
and inculcating their professional experience on the students.
| 45
SIWES REPORT
It prepares students for the work situation they are likely to meet in the real world.
It provides an avenue for students in Nigerian universities to acquire industrial skills and
experience in their course of study.
It creates a platform for students to apply their theoretical knowledge in a practical form, thereby
bridging the gap between the academia and the industrial world.
It makes the transition from the university to real world easier and thus increases the students
contact for future job employment.
The program exposes students on how to co-operate with colleagues and staffs in their various
places of attachment and to be able to face real life problems.
Therefore, against these backdrops; I say thanks to the organizers of the program, my amiable and God
given lecturers and everyone involved in the success of the program.
| 46
SIWES REPORT
CHAPTER 4
During the course of my internship, I was privileged to work in the plant where I was acquainted with how
the most treasured commodity in Nigeria is produced and that’s none other than the premium motor spirit
(PMS) popularly called petrol. I also got to understand that the same principles being practiced at WRPC is
similar to the principles being applied in any petroleum refinery in the world.
| 47
SIWES REPORT
4.5 CONCLUSION
In the course of the program, I came to terms with the different behavioral attitude of the working class.
The program got me a new view on how to handle operational issues with limited time. In all these, I
became confident of my ability to think independently.
SIWES has improved the practical skills of many students today. Indeed I am glad that I was part of it.
Personally speaking, it has improved my mental and practical capabilities in petroleum processing where
those theories learnt in class are being shown firsthand in the field. The objective created by the SIWES has
been organized to enable students have working experience not only the practical aspect of it but also how
to co-operate with members of staff and how to cope with real life problems. The overall benefits have
been immeasurable and invaluable. Therefore it should be encouraged and empowered immensely.
| 48
SIWES REPORT
5 REFERENCES
1. Fractional distillation - Wikipedia, the free encyclopaedia, 2010.
2. F.Y. El Kady, L.k. Mohammed, S.A. Shaban, ”Hydrotreatment of kerosene fraction to improve its
properties”, Petroleum Refining Division. EPRI (July 2010) Vol. 2, 9-10.
3. Abdel-Aal, H.K. and Mohammed, A.: Petroleum and Gas Field Processing, Marcel-Dekker, Kuwait
(2003)
4. WRPC profile manual.
5. WRPC Reforming plant manual.
| 49
SIWES REPORT
6 APPENDICES
APPENDIX A
| 50
SIWES REPORT
A group photo with other internship colleagues at the topping unit (CDU/ADU)
| 51
SIWES REPORT
APPENDIX B
| 52