Professional Documents
Culture Documents
62.1:3710
D200437X012
July 2009 3710 and 3720 Positioners
W6144 / IL
SUPPLY
CONNECTION
EXTERNAL
GROUNDING
SCREW
W6058−1 / IL
www.Fisher.com
Product Bulletin
62.1:3710
3710 and 3720 Positioners July 2009
Specifications
Available Configuration 3720:.
3710: J Single− or J double−acting pneumatic 6mm Spool Valve: 1.0 normal m3/hr
rotary valve positioner (36 scfh) at 4.1 bar (60 psig) supply pressure
3720: J Single− or J double−acting
electro−pneumatic rotary valve positioner Maximum Supply Air Demand(4) (Double−Acting)
consisting of a 3710 with a 3722 attached
3722: An electro−pneumatic converter that 6 mm Spool Valve: 20 normal m3/hr (700 scfh) at
converts a 4−20 mA DC input signal to a 0.2 to 4.1 bar (60 psig) supply pressure
1.0 bar (3 to 15 psig) signal for the pneumatic
positioner Typical Performance(5)
Input Signal 3710 Pneumatic Positioner
Independent Linearity: ±0.5% of output span
3710:. Hysteresis: 0.5% of output span
Standard: J 0.2 to 1.0 bar (3 to 15 psig) or J 0.4 Deadband: 0.3% of input span
to 2.0 bar (6 to 30 psig)
Split−Range: J 0.2 to 0.6 bar (3 to 9 psig) and 0.6 3720 Electro−Pneumatic Positioner
to 1.0 bar (9 to 15 psig) or J 0.4 to 1.2 bar (6 to Independent Linearity: ±1.0% of output span
18 psig) and 1.2 to 2.0 bar (18 to 30 psig) Hysteresis: 0.6% of output span
3720:. Deadband: 0.35% of input span
Standard: J 4−20 mA DC constant current with
30 VDC maximum compliance voltage Electromagnetic Compatibility for 3722
Split−Range: J 4−12 mA DC or 12−20 mA DC electro−pneumatic converter:
Meets EN 61326−1 (First Edition)
Immunity—Industrial locations per Table 2 of
Equivalent Circuit
the EN 61326−1 standard. Performance is
3720: 120 ohms shunted by three 5.6 V zener shown in table 1 below.
diodes Emissions—Class A
ISM equipment rating: Group 1, Class A
Output Signal Note: Electromagnetic Compatibility
Pneumatic pressure as required by the actuator specifications also apply to the 3720
up to full supply pressure positioner
Action(1): Field reversible between direct and
reverse
Operating Influences
Supply Pressure(2) Supply Pressure Sensitivity: A 10% change in
Minimum Recommended: 0.3 bar (5 psig) above supply pressure changes the valve shaft position
actuator requirement less than the following percentages of valve
Maximum: 10.3 bar (150 psig) or maximum rotation:
pressure rating of the actuator, whichever is lower 3710: 1.0% at 4.1 bar (60 psig) supply pressure
3720: 1.5% at 4.1 bar (60 psig) supply pressure
Supply Medium
3710: air or natural gas(3) Operative Temperature Limits(2)
3720: air J −40 to 80_C (−40 to 180_F), J −50 to 107_C
(−58 to 225_F)
The 3720 positioner is not approved for use
with natural gas as the supply medium
Construction Materials
Steady−State Air Consumption(4) Positioner Base: Low copper aluminum alloy
3710:. Cover: Polyester plastic
6 mm Spool Valve: 0.82 normal m3/hr Feedback Shaft: Stainless steel
(29 scfh) at 4.1 bar (60 psig) supply pressure Range Spring: Stainless steel
−continued−
2
Product Bulletin
62.1:3710
July 2009 3710 and 3720 Positioners
Specifications (Continued)
Construction Materials (continued) IECEx—Intrinsic Safety, Flameproof, Type n
Input Module Diaphragm, O−rings: J Nitrile or SAA—Intrinsic Safety, Flameproof, Type n
J Ethylene−propylene (EPDM)
Refer to tables 2, 3, 4, 5, and 6 for additional
Spool Valve: SST/C72900 approvals information.
Tubing: Copper (standard)
Fittings: Brass (standard) Note: These classifications also apply to the
Gauges: Chrome−plated brass connection with 3720 positioner
plastic case
Connectors for diagnostic testing: J Stainless Pressure Connections
steel or J Brass 1/4 NPT internal
Options
Housing Classification for 3722 Span Adjuster Assembly: J 0.2 to 1.0 bar (3 to
CSA Type 3 Encl., NEMA 3, IP54 per IEC 60529. 15 psig) input range or, J 0.4 to 2.0 bar (6 to 30
Mount instrument with vent on side or bottom if psig) input range
weatherproofing is a concern. Elastomers (O−rings, diaphragm): J standard
temperature range, −40 to 80_C (−40 to 180_F),
Note: These classifications also apply to the
J extended temperature range −50 to 107_C
3720 positioner
(−58 to 225_F)
Electrical Classifications for 3722 J special applications J Beacon Indicator,
J Gauges(6), tire valves, or connectors for
CSA—Intrinsic Safety, Explosion Proof, Type n,
diagnostic testing
Dust−Ignition Proof
FM—Intrinsic Safety, Explosion Proof, Type n, Approximate Weight
Non−incendive, Dust−Ignition Proof 3710: 2.04 kg (4.5 pounds)
ATEX—Intrinsic Safety, Flameproof, Type n 3720: 2.72 kg (6.0 pounds)
NOTE: Specialized instrument terms are defined in ANSI/ISA Standard 51.1 − Process Instrument Terminology.
1. Direct−acting, an increasing input signal extends actuator rod. Reverse−acting, an increasing input signal retracts actuator rod.
2. The pressure and temperature limits in this document and any applicable standard or code limitation should not be exceeded.
3. Natural gas should not contain more than 20 ppm of H2S.
4. Normal m3/hr−−Normal cubic meters per hour (0_C and 1.01325 bar, absolute); Scfh−−Standard cubic feet per hour (60_F and 14.7 psia).
5. Typical values determined by tests with a 1061 size 30 actuator at 4.1 bar (60 psig) supply pressure. Performance may vary with other actuator types and supply pressures.
6. Gauges not available for high temperature range.
3
Product Bulletin
62.1:3710
3710 and 3720 Positioners July 2009
4
Product Bulletin
62.1:3710
July 2009 3710 and 3720 Positioners
1 ACTION BLOCK
SPAN ADJ ASSY
NAMEPLATE 2 MOUNTING SCREW HOLE
AREA
SCREENED
VENT
OPENING
SPOOL VALVE
SPAN ADJ
SHAFT INPUT MODULE
(THREADED ROD)
ZERO ADJUSTER
LOCK NUT
ZERO ADJUSTER
SUMMING BEAM
MOUNTING
FEEDBACK MOUNTING SCREW
ARM ASSEMBLY CAM HOLE
W5947 / IL SCREW HOLE
NOTE:
1 THE SPAN ADJ ASSY IS MADE UP OF THE RANGE SPRING, SPAN ADJ SHAFT (THREADED ROD), AND SPAN ADJ KNOB.
2 THE SPAN ADJ ASSY FEATURES A RED COLOR−CODED RANGE SPRING FOR A 6 TO 30 PSIG INPUT SIGNAL
D 1061, sizes 30, 40, 60, and 68 D 1066, sizes 20, 27, and 75
5
Product Bulletin
62.1:3710
3710 and 3720 Positioners July 2009
MOUNTING
SCREW
FEEDBACK
SHAFT
POSITIONER
MOUNTING TIE BAR
MOUNTING
SCREWS EXTENSION
W6059 / IL PLATE
Principle of Operation port A of the spool valve opens, allowing the right
side of the actuator to vent to atmosphere.
Refer to the positioner schematic (figure 6). The
operational description here follows the schematic The piston in the actuator moves to the right, rotating
layout and orientation. the feedback shaft and cam counterclockwise. This
rotation causes the feedback lever to rotate
The 3710 pneumatic positioner is a force−balance clockwise, increasing the compression on the
instrument that provides a control valve position feedback spring. These rotations continue until the
proportional to a pneumatic input signal. The additional force from the spring balances with the
balance of opposing forces in the positioner occurs input module force on the summing beam. When the
at the summing beam. forces are equal, the summing beam returns to its
steady state or neutral position and the actuator is
held at a new position.
One force applied to the summing beam is
developed from the input signal pressure on the In a 3720 positioner, the 3722 converter receives the
diaphragm. The other force is from the feedback milliampere (mA), direct current (DC), input signal
spring and is proportional to the position of the and provides a proportional pneumatic output signal
feedback lever. through a nozzle/flapper arrangement. Nozzle
pressure from the converter module travels through
When the input pressure is increased to the the converter housing to provide the input signal
diaphragm of the input module, the diaphragm pressure to the 3710 pneumatic positioner.
strokes down, increasing the effective force from the
input module and compressing the feedback spring. The feedback lever position is determined by the
The summing beam moves the spool down in the location or rise of the cam (figure 7) which is
spool body, opening output port B to supply air to the attached to the feedback shaft. When the two
left side of the actuator. At the same time, output opposing forces are equal or at a steady state, the
6
Product Bulletin
62.1:3710
July 2009 3710 and 3720 Positioners
INPUT MODULE
SUMMING BEAM
PIVOT
SPOOL VALVE
FEEDBACK
A SPRING
B
SUPPLY CAM
SPAN ADJ
PIVOT
FEEDBACK
LEVER
ZERO ADJ
PIVOT
OUTPUT B
PISTON ACTUATOR
OUTPUT A
A5944−1 / IL
Installation
The supply pressure medium must be a clean, dry,
filtered air, or noncorrosive gas (3710 positioner
only). If the supply source is capable of exceeding
the maximum actuator operating pressure or
positioner supply pressure, take appropriate steps
during installation to protect the positioner and all
connected equipment against overpressure.
CAM ROLLER
Positioner connections including connections for A6045 / IL
7
Product Bulletin
62.1:3710
3710 and 3720 Positioners July 2009
BODY PROTECTOR
BODY
PIPE BUSHING
84.0
(3.31)
PIPE TEE
50.5
(1.99)
1/4−18 NPT
OUTPUT CONN (A)
41.8
PLUGGED ON
(1.65)
SINGLE ACTING PIPE NIPPLE
12B8055−A DIAGNOSTIC CONNECTOR
B2385 / IL
1/4−18 NPT
INSTR CONN
1/4−18 NPT
OUTPUT CONN (B) 1/4−18 NPT
SUPPLY CONN
48.0
167.9 (1.89)
(6.61)
70.3
45.2 (2.77)
(1.78)
68.7 41.8
(2.70) (1.65)
167.9
(6.61) 132.6
(5.22)
A5945−1 / IL
132.6
(5.22)
146.1 39.6
(5.75) (1.56)
mm
11B5496−A INCH
A6149−1 / IL
8
Product Bulletin
62.1:3710
July 2009 3710 and 3720 Positioners
9
Product Bulletin
62.1:3710
3710 and 3720 Positioners July 2009
Table 2. Fisher 3722 Electro−Pneumatic Converter (1) Hazardous Area Classifications—CSA (Canada)
CERTIFICATION
CERTIFICATION OBTAINED ENTITY RATING TEMPERATURE CODE ENCLOSURE RATING
BODY
(Intrinsic Safety)
Vmax = 30 VDC
Zone
Imax = 150 mA T4 (Tamb v 82°C)
Ex ia IIC T4/T5/T6 per drawing GE28591
Pi = 1.25 W T5 (Tamb v 62°C) CSA Type 3 Encl.
Class/Division
Ci = 0 nF T6 (Tamb v 47°C)
Class I, II Division 1 GP A,B,C,D,E,F,G
Li = 0 mH
T4/T5/T6 per drawing GE28591
(Explosion Proof)
Zone
Ex d IIC T5 −−− T5 (Tamb v 82°C) CSA Type 3 Encl.
CSA
Class/Division
Class I, Division 1, GP A,B,C,D T5
(Type n)
Zone −−− T6 (Tamb v 82°C) CSA Type 3 Encl.
Ex nA IIC T6
Class I, Division 2, GP A,B,C,D T6 T6 (Tamb v 82°C)
Class II, Division 1, GP E,F,G T5 −−− T5 (Tamb v 82°C) CSA Type 3 Encl.
Class II, Division 2, GP F,G T6 T6 (Tamb v 82°C)
1. These hazardous area classification also apply to 3720 positioners.
Table 3. Fisher 3722 Electro−Pneumatic Converter (1) Hazardous Area Classifications—FM (United States)
CERTIFICATION
CERTIFICATION OBTAINED ENTITY RATING TEMPERATURE CODE ENCLOSURE RATING
BODY
(Intrinsic Safety)
Zone Vmax = 30 VDC
Class I Zone 0 AEx ia IIC T4/T5/T6 per Imax = 150 mA T4 (Tamb v 82°C)
drawing GE28590 Pi = 1.25 W T5 (Tamb v 62°C) NEMA 3, IP54
Class/Division Ci = 0 nF T6 (Tamb v 47°C)
Class I, II, III Division 1 GP A,B,C,D,E,F,G Li = 0 mH
T4/T5/T6 per drawing GE28590
(Explosion Proof)
Zone
FM Class I Zone 1 AEx d IIC T5 −−− T5 (Tamb v 82°C) NEMA 3, IP54
Class/Division
Class I, Division I, GP A,B,C,D T5
(Type n)
Zone −−− T5 (Tamb v 82°C) NEMA 3, IP54
Class I Zone 2 AEx nA IIC T5
Class I, Division 2, GP A,B,C,D T5
Class II, Division 1, GP E,F,G T5 −−− T5 (Tamb v 82°C) NEMA 3, IP54
Class II, Division 2, GP F,G T5
1. These hazardous area classification also apply to 3720 positioners.
10
Product Bulletin
62.1:3710
July 2009 3710 and 3720 Positioners
Table 6. Fisher 3722 Electro−Pneumatic Converter (1) Hazardous Area Classifications—SAA (Australia)
CERTIFICATION CERTIFICATION OBTAINED ENTITY RATING TEMPERATURE CODE ENCLOSURE RATING
Ui = 32 VDC
Gas Ii = 150 mA
T4 (Tamb v 40°C) IP54
Ex ia IIC T4 − Intrinsic Safety Ci = 0 nF
Li = 0 mH
SAA Gas
−−− T6 (Tamb v 40°C) IP54
Ex d IIB T6 − Flameproof
Gas
−−− T4 (Tamb t 40°C) IP54
Ex n IIC T4 − Type n
1. These hazardous area classification also apply to 3720 positioners.
11
Product Bulletin
62.1:3710
3710 and 3720 Positioners July 2009
Fisher is a mark owned by one of the companies in the Emerson Process Management business division of Emerson Electric Co. Emerson
Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property
of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the
designs or specifications of such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated
entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of
any product remains solely with the purchaser and end−user.
EFisher
12 Controls International LLC 1991, 2009; All Rights Reserved