Professional Documents
Culture Documents
ISO 262:1998
m4ti, mlmm?RfaTadmd3fmm
Rwi@m)
Indian Standard
ISO GENERAL PURPOSE METRIC SCREW THREADS
PART 4 SELI?CTED SIZES FOR SCREWS, BOLTS AND NUTS
( Seco;d Revision )
Ics 21.040.01
,--
@ BIS 2001
!,
NATIONAL FOREWORD
This Indian Standard ( Part 4 ) ( Second Revision ) which is identical with ISO 262:1998 ‘ISO general
purpose metric screw threads — Selected sizes for screws, bolts and nuts’ issued by the International [J,.
Organization for Standardization ( ISO ) was adopted by the Bureau of Indian Standards on the recommendation ,$
of the Engineering Standards Sectional Committee and approval of the Basic and Production Engineering ‘;1
i“
Division Council.
This standard was originally issued in 1967 and subsequently revised in 1976. The first revision was
based on ISO 965/1 ‘ISO general purpose metric screw threads —Tolerances — Part 1: Principles and
basic data’, DIN 13 Sheet 14 and DIN 13 Sheet 15 covering the tolerances. This second revision has
been issued by adopting ISO 262:1998 and covers the selected sizes for screws, bolts and nuts which
were earlier covered in IS 4218 ( Part 6 ) :1978 and IS 12241 :1987. The principles and basic data for $
;
tolerances on screws, bolts and nuts now covered in Part 1 of new standard, that is’ IS 14962 ( Part 1 )
‘[ ,“
published on tolerances for ISO general purpose metric screw threads by adopting ISO 965-1:1998. )4
After the publication of this standard IS 4218 ( Part 6 ) :1978 and IS 12241 :1987 stand withdrawn. ;’
The Committee, responsible for preparation of Indian Standards on Screw Threads, decided to revise all $’
,’
the six parts of IS 4218 in the following manner:
b) For tolerances on ISO general purpose metric screw threads a new standard, that is IS 14962 to
be published in five parts, that is ( Parts 1 to 5 ) by adopting ISO 965 ( Part 1 ) :1998, <,,
ISO 965 ( Part 2 ) :1998, ISO 965 ( Part 3 ) :1998, ISO 965 ( Part 4 ) :1998 and ISO 965
~
( Part 5 ) :1998 respectively; and
~;
c) After the publication of above standards IS 4218 ( Part 5 ): 1979 and IS 4218 ( Part 6 ) :1978 j,
stand withdrawn.
The text of ISO Standard has been approved as suitable for publication as an Indian Standard without
deviations. In the adopted standard certain conventions are not identical to those used in Indian Standards.
Attention is especially drawn to the following:
a) Wherever the words ‘International Standard’ appear referring to this standard, they should be
read as ‘Indian Standard’.
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is
to use a full point (.) as the decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian Standards
also exist. The corresponding Indian Standards which are to be substituted in their place are listed
below along with their degree of equivalence for the editions indicated:
ISO 68-1:1998 IS 4218 ( Part 1 ) :2001 ISO general purpose metric Identical
screw threads: Part 1 Basic profile ( second revision)
Indian Standard
ISO GENERAL PURPOSE METRIC SCREW THREADS
PART 4 SELECTED SIZES FOR SCREWS, BOLTS AND NUTS
(Second Revision )
1 Scope
This International Standard specifies selected sizes for screws, bolts and nuts in the diameter range from 1 mm to
64 mm of ISO general purpose metric screw threads (M) having basic profile according to ISO 68-1.
These selected sizes are recommended also for general engineering use.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. Ail standards are subject to
revision, and parties to agreements based on this International. Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 68-1:1998, ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads.
ISO 261:1998, ISO general purpose metric screw threads — General plan.
ISO 965-1:1998, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data.
3 Definitions
For the purposes of this International Standard, the definitions given in ISO 5408 apply.
1
IS 4218 ( Part 4 ) :2001
ISO 262:1998
4 Selected sizes
See table 1.
Table 1
Dimensions in millimetres
= .oaraepi~ fine 9
1 0,25
1,2 0,25
1,4 0,3
1,6 0,35
1,8 0,35
2 0,4
2,5 0,45
3 0,5
3,5 0,6
4 0,7
5 0,8
6 1
7 1
8 1,25 1
10 1,5 1,25 1
12 1,75 1,5 1,25
14 2 1,5
16 2 1,5
18 2,5 2 1,5
20 2,5 2 1,5
22 2,5 2 1,5
24 3 2
27 3 2
30 3,5 2
33 3,5 2
36 I 14 13 I
39 4 3
42 4,5 3
45 4,5 3
48 5 3
52 5 4
56 5,5 4
60 5,5 4
64 6 4
( Continued from second cover)
ISO 965-1:1998 IS 14962 ( Part 1 ) :2001 ISO general purpose metric Identical
screw threads — Tolerances: Part 1 Principles and
basic data
1S No. Title
IS 4218 ( Part 1 ) : 2001/ ISO general purpose metric screw threads: Part 1 Basic profile
ISO 68-1:1998 ( second revision)
IS 4218 ( Part 2 ) : 20(?1/ ISO general purpose metric screw threads: Part 2 General plan
ISO 261:1998 ( second revision)
IS 4218 ( Part 3 ) : 1999/ ISO general purpose metric screw threads: Part 3 Basic dimensions
ISO 724:1993 ( second revision)
Indian Standards ( being ) published on tolerances for ISO general purpose metric screw threads are
listed below:
IS No, Title
IS 14962 ( Part 1 ) : 2001/ ISO general purpose metric screw threads — Tolerances: Part 1
ISO 965-1:1998 Principles and basic data
IS 14962 ( Part 2 ) : 2001/ ISO general purpose metric screw threads — Tolerances: Part 2
ISO 965-2:1998 Limits of sizes for general purposes external and internal screw
threads — Medium quality
1
,.-
I
IS 14962( Part 3 ) : 2001/ ISO general purpose metric screw threads — Tolerances: Part 3
ISO 965-3:1998 Deviations for constructional screw threads
IS 14962 ( Part 4 ) : 2001/ , ISO general purpose metric screw threads —Tolerances: Part 4
ISO 965-4:1998 Limits of sizes for hot-dip galvanized external screw threads to
mate with internal screw threads tapped with tolerance position
H or G after galvanizing
IS 14962 ( Part 5 ) : 2001/ ISO general purpose metric screw threads — Tolerances: Part 5
ISO 965-5:1998 Limits of sizes for internal screw threads to mate with hot-dip
galvanized external screw threati with maximum size of tolerance
position h before galvanizing
In reporting the results of a test or analysis made in accordance with ~is standard, if the final value,
observed or calculated, is to be rounded off, it shall be done in accordance with IS 2:1960 ‘Rules for
rounding off numerical values ( revised)’.
.
\’
&
BIS is a statutory institutionestablished under the Bureau of Indian Standards Act, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of goods and
attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications maybe reproduced in any form without
the prior permission in writing of BIS. This does not preclude the free,use, in the course of implementing the
standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating to
copyright be addressed to the Director (Publications), BIS.
Amendments are issued to standards as the need arises onthebasis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are 1:
needed; if the review indicates that changes are needed, it is taken up for revision., Users of Indian Standards
should ascertain that they are in possession of tlie latest amendments or edition by referring to the latest issue /
of ‘BIS Catalogue’ and’ Standards: Monthly Additions’.
This Indian Standard has been. developed from Doc : No. BP 20 ( 0461 ).
!
\
Amendments Issued Since Publication
;...-