Flow 0.6 m³/h L or D Flux 0.2 m/h Area 3 m² Width/Lenght - square shape - L 1.7 m Diameter - circular shape - D 2.0 m HL Average sand particle diameter 0.3 mm H1 H1 Sand bed height H3 1m H H2 L H2 Minimum water height over the filtration bed H2 0.3 m HC Maximum water height over the filtration bed H1 0.8 m Height of the inter-compartment channel HL 0.10 m H3 Height of the compact filter Hc 1.9 m Height of the conventional design filter H 2.1 m Flow H4 H3 Flow Support layers Uniform coefficient of the support materials 1.3 H5 Top layer - Sand - Particle diameter 1.3 mm H6 HL Top layer- Areia - Height H4 0.10 m Intermediate layer - Seixos - Particle diameter 5 mm Intermediate layer - Seixos - Height H5 0.1 m Inferior layer - Seixos - Particle diameter 10 mm Inferior layer - Seixos - Height H6 0.1 m Notes about the operation: - Slow sand filters cannot be backwashed. The top of the filter bed should be scraped (2 - 5cm) every time the water depht reached the H1 height. - Never allow the water level to be beyond the H2 height (follow the piping layout from the conventional layout drawing). - Slow sand filters are based on biological processes therefore the water cannot be pre-chlorinated. - The turbidity of the feedwater should be under 5 NTU for optimal performance. - The best performance will be reached after 10 or 15 days of operation, when the biological filtration layer (schmutzdecke) is stabilished and functional. - It's recomended to keep the filter covered to avoid algae growth. Dimensionamento de Filtros Lentos Atende a norma NBR12216
Vazão 0.6 m³/h L ou D Taxa 0.2 m/h Área 3 m² Lateral - quadrado - L 1.7 m Diâmetro - circular - D 2.0 m HL Diâmetro dos grãos de areia 0.3 mm H1 H1 Profundidade do leito de areia H3 1m H H2 L H2 Altura mínima de água acima da areia H2 0.3 m HC Altura máxima da água sobre a areia H1 0.8 m Altura do canal de interligação HL 0.10 m H3 Altura do tanque compacto Hc 1.9 m Altura do tanque convencional H 2.1 m Fluxo H4 H3 Fluxo Camadas de base Coeficiente de uniformidade das camadas 1.3 H5 Base superior - Areia - Diâmetro 1.3 mm H6 HL Base superior - Areia - Espessura H4 0.10 m Base intermediária- Seixos - Diâmetro 5 mm Base intermediária - Seixos - Espessura H5 0.1 m Base inferior - Seixos - Diâmetro 10 mm Base inferior - Seixos - Espessura H6 0.1 m Notas sobre a operação: - Filtros lentos não podem ser contralavados. A camada superior da areia (2 a 5cm) deve ser raspada quando a altura H1 de água for atingida. - Nunca deixar a água ficar abaixo da altura H2 (ver desenho do tubo de saída no arranjo convencional). - Filtros lentos não podem receber dosagem de cloro na alimentação pois baseiam-se em princípios biológicos. - A turbidez de entrada deve ser baixa (< 5 NTU). - O desempenho máximo é atingido após cerca de 10 dias, quando a camada de biofilme (schmutzdecke) é estabelecida. - É recomendável cobrir o filtro para evitar a proliferação de algas.