Professional Documents
Culture Documents
EG8010 Datasheet en PDF
EG8010 Datasheet en PDF
EG8010 Datasheets
ASIC for single-phase SPWM control
EG8010 Datasheets
(Single Phase Sinusoid Inverter ASIC)
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
2 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
Contents
1. Features ............................................................................................................................................................... 4
2. Description ........................................................................................................................................................... 4
3. Application ........................................................................................................................................................... 4
4. Pinouts ................................................................................................................................................................. 6
4.1. Pin map ................................................................................................................................................ 6
4.2. Pin descriptions .................................................................................................................................... 6
5. Block Diagram ...................................................................................................................................................... 7
6. Typical Application schematic .............................................................................................................................. 7
6.1 EG8010+IR2110S Sinusoid inverter(unipolar modulation) .................................................................. 7
6.2 EG8010+IR2110S+Cross‐conduction prevention logic Sinusoid inverter (unipolar modulation) ........ 8
6.3 EG8010+IR2106SSinusoid inverter (unipolar modulation) .................................................................. 8
6.4 EG8010+TLP250 Sinusoid inverter (unipolar modulation) ................................................................... 9
6.5 EG8010+IR2110SSinusoid inverter (bipolar modulation) .................................................................... 9
6.6 EG8010+IR2110S Sinusoid inverter (low power frequency transformer) .......................................... 10
7. Electrical Characteristics .................................................................................................................................... 11
7.1 Absolute maximum ratings ................................................................................................................ 11
7.2 Typical ratings .................................................................................................................................... 11
8. Application note ................................................................................................................................................ 12
8.1 AC Output Voltage Feedback ............................................................................................................. 12
8.2 AC Output Current Feedback ............................................................................................................. 13
8.3 Temperature Feedback ...................................................................................................................... 14
8.4 PWM Output Type Set ....................................................................................................................... 14
8.5 Dead Time Setting .............................................................................................................................. 15
8.6 Frequency Setting .............................................................................................................................. 15
8.7 VVVF (Variable Voltage and Variable Frequency Mode) .................................................................... 16
8.8 Serial 12832 LCD Setting .................................................................................................................... 16
8.9 RS232 Serial communication port ...................................................................................................... 17
9. Package Dimensions ....................................................................................................................................... 21
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
3 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
EG8010 DATASHEETS
1. Features
+5V single supply
4 settingsofoutput frequency can set by 2 pins
50Hz constant frequency sine-wave
60Hz constant frequency sine-wave
0-100Hzadjustable frequency sine-wave
0-400Hz adjustable frequency sine-wave
2 modulation modes can set by1 pin
Unipolar modulation
Bipolar modulation
4 settings of dead time can set by 2 pins
300nS
500nS
1.0uS
1.5uS
External 12MHz crystal oscillator
23.4KHz Modulation frequency
Output Voltage \ Current \ Temperature detect and handle
3 seconds soft start can select by 1 pin
USART communication support
Voltage \ Current \ Temperature \ Frequency Display support by external LCD
Parameters and functions customize support
2. Description
EG8010 is a digital pure sine wave inverter ASIC (Application Specific Integrated Circuit) with
complete function of built-in dead time control. It applies to DC-DC-AC two stage power converter
system or DC-AC single stage low power frequency transformer system for boosting. EG8010 can
achieve 50/60Hz pure sine wave with high accuracy, low harmonic and distortion by external
12MHz crystal oscillator. EG8010 is a CMOS IC that integrates SPWM sinusoid generator, dead
time control circuit, range divider,soft start circuit, circuit protection, RS232 serial communication,
12832 serial LCD unit, and etc.
3. Application
Single-Phase sinusoid inverter Digital Generator
Solar power generation inverter Medium frequency power supply
Wind power generation inverter Single-phase motor speed controller
UPS(Uninterruptible power supply) Single-phase frequency transformer
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
4 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
Sinusoid light modulator Sinusoid generator
Sinusoid voltage regulator Inverter welder
4. Pinouts
4.1. Pin map
Figure 4.1EG8010 pin map
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
6 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
LED warning display:
Normal:
Over current:
8 LEDOUT O
Over voltage:
Below voltage:
Over temperature:
PWM type select
“0”: positive polarity PWM type,MOSFET on when SPWMOUT is high
“1” positive polarity PWM type,MOSFET on when SPWMOUT is low
9 PWMTYP I
Best configuring pin according to driver device and referring to the typical
application schematic below, otherwise will result in both sides of MOS
tubes conducting at the same time.
10 OSC1 I 12MHz extern crystal oscillator input
11 OSC2 I 12MHz extern crystal oscillator output
13 VFB I AC output voltage feedback input
14 IFB I AC output current feedback input
15 TFB I Temperature feedback input
FRQADJ/ Frequency adjust input on Frequency adjust mode
16 I
VFB2 AC output voltage feedback input on Bipolar modulation mode
17 VREF I Voltage reference input
AC output frequency select,
18 FRQSEL0 I “00”: 50Hz
“01”: 60Hz
19 FRQSEL1 I “10”: 0-100Hz Frequency adjust mode
“11”: 0-400Hz Frequency adjust mode
Modulation mode select
20 MODSEL I “0”: Unipolar modulation mode
“1”: Bipolar modulation mode
Soft start enable
21 SST I “0”: Disable
“1”: Enable
22,23 NC - Not connect
24 LCDCLK O Clock signal of LCD serial bus
25 LCDDI O Data signal of LCD serial bus
27 SPWMOUT1 O Right-high FET SPWMOUT of Full bridge
28 SPWMOUT2 O Right-low FET SPWMOUT of Full bridge
29 SPWMOUT3 O Left-high FET SPWMOUT of Full bridge
30 SPWMOUT4 O Left-low FET SPWMOUT of Full bridge
31 LCDEN O Chip select signal of LCD serial bus
Variable voltage variable frequency function enable:
32 VVVF I “0”: Disable
“1”: Enable
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
6 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
5. Block Diagram
Figure 5‐1. EG8010 block diagram
F1
散热风扇
D1状态指示灯说明 +5V 大于45°开启风扇
正常:长亮 9 NC HO 8
过流:闪烁 2下,灭2秒,一直循环 R1 C2 小于40°关闭风扇
过压:闪烁 3下,灭2秒,一直循环 1K 10 NC VB 7
IR2110S
JP3
欠压:闪烁 4下,灭2秒,一直循环 D1 LED +5V 10uF/16V
过温:闪烁 5下,灭2秒,一直循环 11 VDD VS 6 R25 Q1
JP4
2.2K 8050
C5 C6 12 HIN NC 5 D2
8 LEDOUT
7 FANCTR
6 SPWMEN
5 TXD
4 RXD
3 GND
2 DT0
1 DT1
10uF/16V 0.1uF
U1
FR107 RT1
JP7 JP8 13 SD NC 4 FANCTR R19
+12V
17 NTC/10K 200K
死区选择 14 LIN VCC 3
C4 TFB 温度传感器 C24 C23 R21 R23
PWMTYP 15 VSS COM 2
C3
10uF/16V 16 0.01uF 0.1uF 10K 10K
32 31 30 29 28 27 26 25
VVVF
9
0.1uF 正弦波输出电压调整
VFB
OSC1 15
10 11 12 13 14 15 16
C1 22P Y1 LCDEN 16 NC LO 1
12M
OSC2 SPWMOUT4 +5V
C7 22P
U2 14
GND SPWMOUT3
VFB
EG8010 SPWMOUT2
GND
13
+12V V1 D5 IN4148 V2
IFB SPWMOUT1 12 D4 IN4148
TFB +5V
VCC 9 NC HO 8 GND R11 R12
C8 11 4.7Ω 4.7Ω
FRQADJ/VFB2 LCDDI 10 NC VB 7 R13 R14
FRQSEL0 18
FRQSEL1 19
LCDCLK 24
IR2110S
L1 3.3mH P2
SST 21
VS2
NC 22
NC 23
13 SD NC 4 2LO 2.2uF
8 N 正弦 220V输出
+12V
14 LIN VCC 3 P3
C12 GND
15 VSS COM 2
C11
0.1uF 10uF/16V 7 D6 IN4148 V3 D7 IN4148 V4
JP1 JP5 JP2 JP6
1HO
50/60Hz选择 软启动选择 16 NC LO 1 6 R15 R16
4.7Ω 4.7Ω
+5V VS1 R17
5 IRF840 R18 IRF840
R3 10K 10K
温度反馈
GND
100Ω
R7
4
电流反馈
1LO
电压反馈
1K
R2
3
100Ω GND
+5V +5V 2
R8 IFB
C18 C17 C16 C21 C15 10K 1
R10 0.1uF 10uF/16V 0.1uF 1000P 0.1uF
R24
10K P1 康铜丝 0.1Ω
R27
不贴-备用
C30 R5
8
不贴-备用
10K
-
+
U4 +0.65V
LM393
EG8010.IR2110正弦波逆变器
+
-
R6 C20
1.5K 0.01uF
1
R4
10K
驱动电路原理图(单极性调制方式) C19
不贴 -备用
R26
100K
www.EGmicro.com
2. In variable frequency and constant voltage mode (Pin VVVF at “0” low electrical level) 0~100Hz(FRQSEL1,FRQSEL0=10)or 0Hz~400Hz(FRQSEL1,FRQSEL0=11), pin FRQADJ needs to connect an external
adjustable resistor. Pin FRQADJ adjusts output frequency and R23 sets output voltage.
3. In variable frequency and variable voltage mode (Pin VVVF at “1” high electrical level) 0~100Hz(FRQSEL1,FRQSEL0=10) or 0Hz~400Hz(FRQSEL1,FRQSEL0=11), pin FRQADJ needs to connect an
external adjustable resistor. Pin FRQADJ sets output frequency and voltage. EG8010 maintains V/F as a constant. R23 sets output frequency at 50Hz when voltage effective value is 220V.
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
7 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
6.2 EG8010+IR2110S+Cross-conduction prevention logic Sinusoid
F1
散热风扇
+5V
D1状态指示灯说明 大于45°开启风扇
正常:长亮 R1 9 NC HO 8
过流:闪烁 2下,灭 2秒,一直循环 1K
C2 小于40°关闭风扇
10 NC VB 7
IR2110S
过压:闪烁 3下,灭 2秒,一直循环
D1 LED JP3 10uF/16V
欠压:闪烁 4下,灭 2秒,一直循环 +5V Q1
过温:闪烁 5下,灭 2秒,一直循环
11 VDD VS 6 R25
JP4
C5 C6 2.2K 8050
Q2
2SA1015 12 HIN NC 5 D2
JP7 JP8 10uF/16V 0.1uF
8 LEDOUT
7 FANCTR
6 SPWMEN
5 TXD
4 RXD
3 GND
2 DT0
1 DT1
FR107
U1
R31 13 SD NC 4 FANCTR RT1 R19
R30 5.1K +12V
17 NTC/10K 200K
死区选择 14 LIN VCC 3
5.1K TFB 温度传感器 C24 C23 R21 R23
PWMTYP VVVF Q3 15 VSS COM 2
C3 C4
16 0.01uF 0.1uF 10K 10K
32 31 30 29 28 27 26 25
0.1uF 10uF/16V
9
2SA1015 正弦波输出电压调整
VFB
OSC1 LCDCEN
15
10 11 12 13 14 15 16
C1 22P Y1 LCDEN 16 NC LO 1
R33
12M R32 5.1K
OSC2 SPWMOUT4 +5V
C7 22P
U2 5.1K 14
GND SPWMOUT3
VFB
EG8010 SPWMOUT2
Q4
2SA1015
GND
13
R35 +12V V1 V2
IFB SPWMOUT1 R34 5.1K 12 D4 IN4148 D5 IN4148
2HO IRF840
MODSEL 20
LCDCLK 24
IR2110S
0.1uF 10uF/16V R37 +5V 11 VDD VS 6
10uF/16V
10 10K 0.1uF/630V 10K 0.1uF/630V
正弦220V输出
VREF 17
LCDDI
5.1K
10uF/16V 0.1uF
12 HIN NC 5 D3 9 C22
L P2
FR107
U3
13 SD NC 4 2LO 2.2uF
8 N P3
LCDCLK
+12V
+5V
14 LIN VCC 3
LCDCLK
LCDCEN
正弦220V输出
LCDDI
C11 GND
C12
7
GND
GND
+5V
软启动选择
8
4.7Ω 4.7Ω
+5V VS1
P?
5 R17 IRF840 R18
10K
IRF840
10K
温度反馈 R3
GND
100Ω 4
电流反馈 R38 R7
1LO
电压反馈
100K 1K
R2
3
100Ω GND
+5V +5V 2
R8
10K IFB
C24 C18 C17 C16 C21 C15 1
R10
0.01uF 0.1uF 10uF/16V 0.1uF 1000P 0.1uF R24
10K P1 康铜丝 0.1Ω
R27
不贴 -备用
C30 R5
8
不贴 -备用 10K
-
+
U4 +0.65V
LM393
EG8010.IR2110正弦波逆变器(EG03)
+
-
R6 C20
R4 1.5K 0.01uF
1
10K
驱动电路原理图(单极性调制方式) C19
不贴 -备用
R26
100K
www.EGmicro.com
F1
散热风扇
D1状态指示灯说明 +5V
正常:长亮
大于 45°开启风扇
过流:闪烁 2下,灭 2秒,一直循环 R1 小于 40°关闭风扇
过压:闪烁 3下,灭 2秒,一直循环 1K
欠压:闪烁 4下,灭 2秒,一直循环 D2 LED JP3
C2 C1 FR107
JP7 JP8 C3 FANCTR RT1 R19
10uF/16V 0.1uF 17 NTC/10K 200K
死区选择 10uF/16V
1 VCC VB 8
TFB 温度传感器 C24 C23 R21 R23
PWMTYP 16 0.01uF 0.1uF 10K 10K
IR2106
VVVF
32 31 30 29 28 27 26 25
9
正弦波输出电压调整
2 HIN HO 7
VFB
OSC1 15
10 11 12 13 14 15 16
C4 22P Y1 LCDEN
12M R30 10K
OSC2 SPWMOUT4 3 LIN VS 6
+5V
C5 22P 14
U1
GND U2 SPWMOUT3
R31 10K
LO
EG8010
4 COM 5
GND
VFB SPWMOUT2
R32 10K 13
R33 10K +12V +12V V1 D5 IN4148 V2
IFB SPWMOUT1 12 D4 IN4148
TFB +5V D3
VCC C8 GND R11 R12
C9
10uF/16V 0.1uF
C10 FR107 11 4.7Ω 4.7Ω
FRQADJ/VFB2 LCDDI R13 IRF840 R14
FRQSEL0 18
FRQSEL1 19
C6 C7 IRF840 C28
MODSEL 20
LCDCLK 24
L1 3.3mH
IR2106
P2
SST 21
NC 22
NC 23
VS2 正弦 220V输出
2 HIN HO 7 9 C22
L
2LO 2.2uF
3 LIN VS 6 8 N 正弦 220V输出
U3
P3
D8 D9 D10 D11 GND
4 COM LO 5 7 D6 IN4148 D7 IN4148
JP1 JP5 JP2 JP6
4148 4148 4148 4148
1HO
50/60Hz选择 软启动选择 6 R15 R16
4.7Ω V3 4.7Ω V4
+5V VS1
5 R17 IRF840 R18 IRF840
R3 10K 10K
温度反馈
GND
100Ω
R7
4
电流反馈
1LO
电压反馈
1K
R2
3
100Ω GND
+5V +5V 2
R8 IFB
R4 R28 R26 R5 C14 C13 C12 C17 C11 10K 1
0.1uF 10uF/16V 0.1uF 1000P 0.1uF
10K 20K
10K 20K
P1 康铜丝
R24
+2.5V 0.1Ω
EG8010.IR2106正弦波逆变器
-
U4
+
LM393
+
驱动电路原理图(单极性调制方式)
-
1
www.EGmicro.com R29
20K
3. In variable frequency and constant voltage mode (Pin VVVF at “0” low electrical level) 0~100Hz(FRQSEL1,FRQSEL0=10)or 0Hz~400Hz(FRQSEL1,FRQSEL0=11), pin FRQADJ needs to connect an
external adjustable resistor. Pin FRQADJ adjusts output frequency and R23 sets output voltage.
4. In variable frequency and variable voltage mode (Pin VVVF at “1” high electrical level) 0~100Hz(FRQSEL1,FRQSEL0=10) or 0Hz~400Hz(FRQSEL1,FRQSEL0=11), pin FRQADJ needs to connect an
external adjustable resistor. Pin FRQADJ sets output frequency and voltage. EG8010 maintains V/F as a constant. R23 sets output frequency at 50Hz when voltage effective value is 220V.
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
8 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
6.4 EG8010+TLP250 Sinusoid inverter (unipolar modulation)
+5V +12V +400V
F1
散热风扇
D1状态指示灯说明 +5V
正常:长亮
D1 FR107 大于 45°开启风扇
1 8
过流:闪烁 2下,灭 2秒,一直循环 R1
C2 C1
小于 40°关闭风扇
过压:闪烁 3下,灭 2秒,一直循环 1K 2
欠压:闪烁 4下,灭 2秒,一直循环 D2 LED JP3
7
10uF/16V 0.1uF
过温:闪烁 5下,灭 2秒,一直循环 R8 R2 Q1
33 6
JP4
510Ω C3 2.2K 8050
0.1uF 4 U2 5
8 LEDOUT
7 FANCTR
6 SPWMEN
5 TXD
4 RXD
3 GND
2 DT0
1 DT1
TLP-250
JP7 JP8 FANCTR RT1 R3
17 NTC/10K 200K
死区选择
1 8 TFB 温度传感器 C5 C4 R4 R5
PWMTYP VVVF
C6 16 0.01uF 0.1uF 10K 10K
32 31 30 29 28 27 26 25
9
2 7 0.1uF 正弦波输出电压调整
VFB
OSC1 R7
15
10 11 12 13 14 15 16
C7 22P Y1 LCDEN 33
Q2 6
12M 510Ω C8
OSC2 SPWMOUT4 S8050 +5V
C9 22P
U1 0.1uF 4 U3
TLP-250
5
14
GND SPWMOUT3 C10
VFB
EG8010 SPWMOUT2 D3 FR107
10uF/16V GND
13
1 8
+12V +12V V1 D4 IN4148 V2
IFB SPWMOUT1
2
C12 C11 12 D5 IN4148
+5V
7
10uF/16V 0.1uF
TFB VCC R10 GND R11 R12
Q3
33 6 11 4.7Ω 4.7Ω
FRQADJ/VFB2 LCDDI 510Ω C13 R13 IRF840 IRF840 C29
R14
FRQSEL0 18
FRQSEL1 19
LCDCLK 24
0.1uF U4 2HO
0.1uF 10uF/16V
4
TLP-250
5
10 10K
C28
0.1uF/630V 10K 0.1uF/630V L1 3.3mH
VREF 17
P2
SST 21
NC 22
NC 23
VS2
9 L 正弦 220V输出
1 8
C16
2LO 2.2uF
2
C17
0.1uF 8 N 正弦 220V输出
R30 R31 7
P3
510Ω 510Ω R32 GND
510Ω C18
33 6
7 D6 IN4148 V3 D7 IN4148 V4
JP1 JP5 JP2 JP6
0.1uF 4 U5 1HO
6
5
TLP-250 R15 R16
50/60Hz选择 软启动选择
4.7Ω 4.7Ω
+5V +5V VS1 R17 IRF840
5 IRF840 R18
R19 10K 10K
温度反馈
GND
100Ω
R20
4
电流反馈
1LO
电压反馈
1K
R21
3
100Ω GND
+5V 2
R6
IFB
R22 R23 R26
C19 C20 C21 C22 C23
10K 1
R28 0.1uF 10uF/16V 0.1uF 1000P 0.1uF
10K 1K 10K 10K P1 康铜丝
R24
+2.5V 0.1Ω
C24
R25 C25 R27 C27
8
1000P
U6
+
LM393
+
驱动电路原理图(单极性调制方式)
-
R33
1
20K
www.EGmicro.com C26
0.01uF R9 20K
5. In variable frequency and constant voltage mode (Pin VVVF at “0” low electrical level) 0~100Hz(FRQSEL1,FRQSEL0=10)or 0Hz~400Hz(FRQSEL1,FRQSEL0=11), pin FRQADJ needs to connect an external
adjustable resistor. Pin FRQADJ adjusts output frequency and R23 sets output voltage.
6. In variable frequency and variable voltage mode (Pin VVVF at “1” high electrical level) 0~100Hz(FRQSEL1,FRQSEL0=10) or 0Hz~400Hz(FRQSEL1,FRQSEL0=11), pin FRQADJ needs to connect an
external adjustable resistor. Pin FRQADJ sets output frequency and voltage. EG8010 maintains V/F as a constant. R23 sets output frequency at 50Hz when voltage effective value is 220V.
F1
散热风扇
+5V
D1状态指示灯说明
正常:长亮 9 NC HO 8
大于45°开启风扇
过流:闪烁 2下, 灭 2秒,一直循环 R1
1K
C2 小于40°关闭风扇
过压:闪烁 3下, 灭 2秒,一直循环 10 NC VB 7
IR2110S
JP3
欠压:闪烁 4下, 灭 2秒,一直循环 D1 LED +5V 10uF/16V
过温:闪烁 5下, 灭 2秒,一直循环 11 VDD VS 6 R25 Q1
JP4
2.2K 8050
C5 C6 12 HIN NC 5 R19 R26
D2
8 LEDOUT
7 FANCTR
6 SPWMEN
5 TXD
4 RXD
3 GND
2 DT0
1 DT1
FR107 RT1
JP7 JP8 13 SD NC 4 FANCTR
死区选择 14 LIN VCC 3
+12V 17 NTC/10K
C3 C4 TFB 温度传感器 C24 C23 R21 R23 C25 R27 R23
0.1uF 10K 10K 0.1uF 10K 10K
PWMTYP VVVF 15 VSS COM 2 0.1uF 10uF/16V 16 0.01uF
32 31 30 29 28 27 26 25
9
OSC1 VFB
10 11 12 13 14 15 16
LCDEN 16 NC LO 1
C1 22P Y1
12M
15
OSC2 SPWMOUT4 +5V
C7 22P
GND
U2 SPWMOUT3
14 正弦波输出电压调整
VFB
EG8010 SPWMOUT2
GND
13
+12V D5 IN4148
IFB SPWMOUT1 D4 IN4148
+5V
12
TFB VCC 9 NC HO 8 GND R11 R12
C8
FRQADJ/VFB2 LCDDI 10 NC VB 7
11 4.7Ω
R13
V1
IRF840
4.7Ω
R14
V2
IRF840
C9 C10
FRQSEL0 18
FRQSEL1 19
2HO
MODSEL 20
LCDCLK 24
IR2110S
0.1uF/630V L1 3.3mH P2
SST 21
VS2
NC 22
NC 23
0.1uF/630V
C13 C14 12 HIN NC 5 D3
9 C22
L 正弦220V输出
10uF/16V 0.1uF FR107 L2 3.3mH
U3
13 SD NC 4 2LO 2.2uF
+12V 8 N 正弦220V输出
14 LIN VCC 3 P3
C11 C12 GND
D6 IN4148 D7 IN4148
JP1 JP5 JP2 JP6
15 VSS COM 2 0.1uF 10uF/16V 7
1HO
16 NC LO 1 R15 R16
50/60Hz选择 软启动选择 6 4.7Ω V3 4.7Ω V4
+5V VS1 R17 IRF840 R18 IRF840
不贴 -备用
10K
- +
U4 +0.65V
EG8010.IR2110正弦波逆变器 LM393
- +
R6 C20
10K
www.EGmicro.com
R30
C19 100K
不贴 -备用
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
9 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
6.6 EG8010+IR2110S Sinusoid inverter (low power frequency
transformer)
+5V +12V/+24V/+36V
+12V
F1
散热风扇
+5V
D1状态指示灯说明 大于45°开启风扇
正常:长亮 9 NC HO 8
过流:闪烁 2下,灭 2秒,一直循环 R1 C2 小于40°关闭风扇
过压:闪烁 3下,灭 2秒,一直循环 1K 10 NC VB 7
IR2110S
JP3
欠压:闪烁 4下,灭 2秒,一直循环 D1 LED +5V 10μF/16V
过温:闪烁 5下,灭 2秒,一直循环 11 VDD VS 6 R29 Q1
JP4
2.2K 8050
C5 C6 12 HIN NC 5 D2
8 LEDOUT
7 FANCTR
6 SPWMEN
5 TXD
4 RXD
3 GND
2 DT0
1 DT1
10μF/16V 0.1μF
U1
FR107 RT1
JP7 JP8 13 SD NC 4 FANCTR
+12V
17 NTC/10K C24
死区选择 14 LIN VCC 3 D8
温度传感器 0.01μF
C4 TFB
PWMTYP 15 VSS COM 2
C3
10μF/16V 16 R25 FR107 FR107
32 31 30 29 28 27 26 25
VVVF 0.1μF
9
100K
VFB R28 FR107 FR107
OSC1 16 NC LO 1 15
10 11 12 13 14 15 16
+5V
TFB VCC 9 NC HO 8 GND R11 R12 T1
C8 11 4.7Ω V1 4.7Ω V2
FRQADJ/VFB2 LCDDI 10 NC VB 7 R13 IRF3205 IRF3205
4
C9 C10 R14
FRQSEL0 18
FRQSEL1 19
2HO
MODSEL 20
LCDCLK 24
SST 21
VS2 P2
NC 22
NC 23
L 正弦 220V输出
10μF/16V 0.1μF
FR107 C22
U3
13 SD NC 4 2LO
+12V
8 2
2.2μF
N 正弦 220V输出
14 LIN VCC 3
C12 GND
15 VSS COM 2
C11
0.1μF 10μF/16V 7 D6 IN4148 D7 IN4148
P3
4.7Ω V3 4.7Ω V4
VS1
温度反馈
+5V
R3
5 R17
10K
IRF3205 R18
10K
IRF3205
工频变压器
GND
100Ω
R7
4
电流反馈
1LO
电压反馈
1K
R2
3
100Ω GND
+5V +5V 2
IFB
C18 C17 C16 C21 C15
R8
10K 1
R10 0.1μF 10uF/16V 0.1uF 1000P 0.1uF
R31
10K P1 康铜丝 0.01Ω
R27
不贴 备用
C30 R5
8
不贴 备用
10K
-
+
U4 +0.65V
LM393
+
基于EG8010工频变压器正弦波逆变器
-
R6 C20
1.5K 0.01μF
1
R4
10K
驱动电路原理图(单极性调制方式) C19
不贴 备用
R26
100K
www.EGmicro.com
2. For full-bridge power MOSFET choose low Rdson MOSFET according to the input voltage.
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
10 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
7. Electrical Characteristics
7.1 Absolute maximum ratings
TA=25℃ unless otherwise specified.
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
11 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
8. Application note
8.1 AC Output Voltage Feedback
EG8010 works under two modulation modes: unipolar modulation and bipolar modulation.
Under unipolar modulation, only one bridge (EG8010 pins SPWMOUT3 & SPWMOUT4) is used
for SPWM modulate output, and another bridge (EG8010 pins SPWMOUT1,SPWMOUT2) is used
for fundamental wave output. A filter inductor needs to connect to SPWM output port, and a voltage
feedback circuit needs to connect to SPWM inductor’s output port(as shown in Fig 8.1a). Under
bipolar modulation, both bridges (EG8010 pins SPWM3, SPWM4, SPWM1, SPWM2) are used for
SPWM output. Using both inductors will result in better flirting, a voltage feedback circuit need
difference and feedback handling by voltage divider of both channels (as shown in Fig 8.c).
Under unipolar modulation, EG8010’s voltage feedback process is through measuring the AC
voltage output of inverter by pin(13)VFB. Pin (16)FRQADJ/VFB2 only functions as FRQADJ,
while VFB2 feedback has no effect. For such voltage sampling and feedback circuit shown in Fig
8.1a, it calculates the error between measured peak voltage and the sinusoid voltage reference (3V),
and adjusts the output voltage accordingly. When output voltage increases, the pin voltage increases.
The circuit does the error calculation and adjust range divider factor, therefore decreases the voltage
to achieve voltage stabilization. Conversely, as the voltage on this pin decreases, the chip will
increase output voltage.
CH1:220V/50Hz AC output wave CH1: VFB voltage feedback wave
Figure 8.1a EG8010voltage sampling and feedback circuit under unipolar modulation
Figure 8.1bObservedSPWM unipolar modulation sinusoid output and VFB feedback wave
Figure 8.1b is the actual testing wave under unipolar modulation. EG8010 uses the peak point
sampling to output voltage, which has advantages of accurate voltage stabilization and short voltage
adjustment time. If output voltage is deviated by some reasons such as change of load or input
voltage, EG8010 can recover to expected output voltage in one to three AC cycle.
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
12 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
Under bipolar modulation, EG8010’s voltage feedback process is through measuring the output
voltage of the left bridge by pin VFB2. Pin (16)FRQADJ/VFB2 only functions as VFB2 to measure
the output voltage of right bridge, while FRQADJ has no effect at this time. For such voltage
feedback circuit shown in Fig 8.c, it calculates the error between peak differential voltage measured
by two channels differential feedback and the sinusoid max voltage reference (3V), and adjusts the
output voltage accordingly. The circuit does the error calculation and adjust range divider factor to
achieve voltage stabilization. Bipolar modulation can adjust to expected output voltage in one to
three AC cycle as well.
Figure 8.1cEG8010Outputvoltage feedback circuit under bipolar modulation
To prevent output voltage is too low or too high when supply to the load, EG8010 has integrated
overvoltage and undervoltage protection. Overvoltage protection is set at 3.15V with 300mS delay.
Undervoltage protection is set at 2.75V with 3S delay. When either situation happens, depending on
pin (9)PWMTYP’s setting, EG8010 will set the level of SPWMOUT1 to SPWMOUT4 at “0” or “1”,
and shut down all power MOSFET to decrease the voltage to zero. Eight seconds after overvoltage
or undervoltage protection activates, EG8010 will turn on power MOSFET for 100ms to
re-determine output voltage. If overvoltage or undervoltage issue still exists, EG8010 will repeat the
process above every eight seconds. If EG8010 runs regularly for more than one minute, it will zero
the counter of overvoltage and undervoltage. However, if EG8010 does not function regularly after
five 8-second cycle, it will complete turn off the output of SPWM unit. It needs a hard reset to start
again.
Figure 8.3a EG8010 Temperature detection circuit
Figure 8.4a EG8010 Positive PWM output Figure 8.4b EG8010 Positive PWM driver IR2110
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
14 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
PWMTYP=“1” outputs negative PWM and applies to the field where the dead level is
meanwhile high (such as opticalcoupler’s negative pole likeTLP250). Figure 8.4c is the output wave
of SPWMOUT. (low electrical level drives opticalcoupler and outputs high level drive power
MOSFET),. Figure 8.4d is an application schematic of negative PWM type driver TL250
opticalcoupler.
Figure 8.4c Negative PWM output Figure 8.4d Negative PWM output drives TLP250
Figure 8.5a EG8010 Dead time control setting
Figure 8.6a EG8010 Frequency adjust circuit
Figure 8.8a EG8010 Serial 12832 LCD
EG8010’s LCD communication control protocol supports ST7920 LCD modules such as 12832
LCD. Control time sequence is shown in figure 8.8b.
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
16 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
Figure 8.8b EG8010 Serial 12832 LCD time sequence
Figure 8.8c: Display on LCD when EG8010 connects to 12832 Figure 8.8d: 12832 LCD dimension
Figure 8.9a RS232serial communication port
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
17 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
Serial port parameters:
Baud rate:2400
Data bit length:8
Parity:none
Stop bit:1
Protocol description:
Use MCU or PC as master,EG8010 as server. Once server receives data from master, it
responds immediately and sends the data back to master.
Protocol data format
Serial Parameter:2400 8 N 1
Format shown as the figure above. During the communication, master sends two bytes data: the
first is command byte and the second is data byte. When server receives two bytes, immediately
returns four data bytes.
Command format:
Read Mode:
1. Read voltage, current, temperature and frequency.
Read voltage, current, temperature AD values and frequency. EG8010
Function returns BYTE1 (voltage AD value), BYTE2 (current AD value), BYTE3
(temperature AD value) and BYTE4 (frequency)
BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Master CODE 41H(Read) 0 1 0 0 0 0 0 1
sends DATA 00H 0 0 0 0 0 0 0 0
Server BYTE1 Voltage V7 V6 V5 V4 V3 V2 V1 V0
returns BYTE2 Current I7 I6 I5 I4 I3 I2 I1 I0
BYTE3 Temperature T7 T6 T5 T4 T3 T2 T1 T0
BYTE4 Frequency F7 F6 F5 F4 F3 F2 F1 F0
V7~V0: Feedback voltage AD value from pin VFB
I7~I0: Feedback current AD value from pin IFB
T7~T0: Feedback temperature AD value from pin
F7~F0: configuration of sinusoid output frequency
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
18 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
2. Enable/ disable SPWM output
Enable/ disable SPWM output
Function Once EG8010 receives the command, it returns BYTE1 (81H) to
indicate written successfully.
BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Master CODE 81H 1 0 0 0 0 0 0 1
sends CTL Control - - - - - - - -
byte
Server BYTE1 81H 1 0 0 0 0 0 0 1
returns BYTE2 Reserved 0 0 0 0 0 0 0 0
BYTE3 Reserved 0 0 0 0 0 0 0 0
BYTE4 Reserved 0 0 0 0 0 0 0 0
The second byte the master sends is control byte CTL
CTL= “55h”: Enable SPWM output.
CTL= “0AAH”: Disable SPWM output.
3. Write control commands
EG8010’s working mode is configured by serial communication
Function Once EG8010 receives the command, it returns BYTE1 (82H) to
indicate written successfully.
BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Master CODE 82H 1 0 0 0 0 0 1 0
sends CTL Control MOD DT1 DT0 VVVF SST MS FS1 FS0
byte
Server BYTE1 82H 1 0 0 0 0 0 1 0
returns BYTE2 Reserved 0 0 0 0 0 0 0 0
BYTE3 Reserved 0 0 0 0 0 0 0 0
BYTE4 Reserved 0 0 0 0 0 0 0 0
MOD sets the control mode: “0”= by external I/O; “1”=by internal register
DT1, DT0 sets the dead time: “00”= 300nS; “01”= 500nS; “10”=1uS; “11”= 1.5uS
VVVF selects variable voltage variable frequency mode: “0”= variable frequency constant voltage;
“1”= variable frequency variable voltage
SST selects soft start mode: “0”= soft start mode off; “1”= soft start mode on.
MS selects modulation mode: “0”= unipolar modulation; “1”= bipolar modulation.
FS1, FS0 selects AC output frequency: “00”= 50Hz, “01”= 60Hz, “10”= 0~100Hz, “11”= 0~
400Hz
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
19 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
4. Write AC output voltage
Write output voltage.
Function Once EG8010 receives the command, it returns BYTE1 (83H) to
indicate written successfully.
BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Master CODE 83H 1 0 0 0 0 0 1 1
sends Vol Value V7 V6 V5 V4 V3 V2 V1 V0
Server BYTE1 83H 1 0 0 0 0 0 1 1
returns BYTE2 reserved 0 0 0 0 0 0 0 0
BYTE3 reserved 0 0 0 0 0 0 0 0
BYTE4 reserved 0 0 0 0 0 0 0 0
Voltage is adjusted linearly. 1LSB= 19.6mV
Vol7 ~Vol0 ranges from 0x00~0xFF, corresponding to Pin VFB’s voltage 0V~5V
5. Write AC output frequency
Write output frequency.
Function Once IC receives the command, it returns BYTE1 (84H) to
indicate written successfully.
BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Master CODE 84H 1 0 0 0 0 1 0 0
sends FRQ Value F7 F6 F5 F4 F3 F2 F1 F0
Server BYTE1 84H 1 0 0 0 0 1 0 0
returns BYTE2 reserved 0 0 0 0 0 0 0 0
BYTE3 reserved 0 0 0 0 0 0 0 0
BYTE4 reserved 0 0 0 0 0 0 0 0
When FRQSEL1 and FRQSEL0 = “10”,
Frq7~Frq0= “0x00”: Output frequency= 0Hz
Frq7~Frq0= “0xFF”: Output frequency= 100Hz
Frq7~Frq0= “0x7F”: Output frequency= 50Hz
When FRQSEL1 and FRQSEL0 = “11”,
Frq7~Frq0= “0x00”: Output frequency= 0Hz
Frq7~Frq0= “0xFF”: Output frequency= 400Hz
Frq7~Frq0= “0x7F”: Output frequency= 200Hz
Above are linear adjustments.
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
20 / 20
micro corp. EG8010 Datasheets
ASIC for single-phase SPWM control
9. Package Dimensions
LQFP32 package dimension:
器
0.25
辑
F 编
P D
捷
Symbol A A1 A2 A3 b b1 c c1 D D1 E E1 e eB L L1 θ
MIN ‐ 0.05 1.35 0.59 0.32 0.31 0.13 0.12 8.80 6.90 8.80 6.908.10 0.40 0
0.80 1.00
NOM ‐ ‐ 1.40 0.64 ‐ 0.35 ‐ 0.13 9.00 7.00 9.00 7.00 ‐ ‐ ‐
BSC BSC
迅
MAX 1.60 0.20 1.45 0.69 0.43 0.39 0.18 0.14 9.20 7.10 9.20 7.10 8.25 0.65 7
O
Unit mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
Copyright © 2014 by EG Microelectronics Corporation
www.EGmicro.com
21 / 20