Professional Documents
Culture Documents
310-00C Fuel System - General Information - 2.0L EcoBoost (184kW/250PS) - 2013 - 2014 Fusion
MI4
General Procedures Procedure revision date: 05/23/2013
Disconnect
NOTICE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove
any foreign material from the connector retaining clip area before separating from the tube or damage
to the tube or connector retaining clip may occur.
NOTICE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is
essential that absolute cleanliness is observed when working with these components or component
damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTICE: Do not use any tools. The use of tools may cause a deformity in the clip components which
may cause fuel leaks.
NOTE: Type 1
1. WARNING: Before beginning any service procedure in this section, refer to Safety Warnings
in section 100-00 General Information. Failure to follow this instruction may result in serious
personal injury.
Refer to: Gasoline and Gasoline-Ethanol Fuel Systems Health and Safety Precautions (100-00 General
Information, Description and Operation).
2. If servicing a liquid fuel tube quick connect coupling, release the fuel system pressure.
Refer to: Fuel System Pressure Release (310-00C Fuel System - General Information - 2.0L EcoBoost
(184kW/250PS) - MI4, General Procedures).
4.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 2 of 14
5.
Connect
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 3 of 14
2. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick
connect coupling.
Press the retainer clip into the quick connect coupling body until flush and the tabs are locked in place.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 4 of 14
Disconnect
NOTICE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove
any foreign material from the connector retaining clip area before separating from the tube or damage
to the tube or connector retaining clip may occur.
NOTICE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is
essential that absolute cleanliness is observed when working with these components or component
damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTICE: Do not use any tools. The use of tools may cause a deformity in the clip components which
may cause fuel leaks.
NOTE: Type 2
1. WARNING: Before beginning any service procedure in this section, refer to Safety Warnings
in section 100-00 General Information. Failure to follow this instruction may result in serious
personal injury.
Refer to: Gasoline and Gasoline-Ethanol Fuel Systems Health and Safety Precautions (100-00 General
Information, Description and Operation).
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 5 of 14
4.
5.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 6 of 14
Connect
1.
2.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 7 of 14
Disconnect
NOTICE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove
any foreign material from the connector retaining clip area before separating from the tube or damage
to the tube or connector retaining clip may occur.
NOTICE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is
essential that absolute cleanliness is observed when working with these components or component
damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTICE: Do not use any tools. The use of tools may cause a deformity in the clip components which
may cause fuel leaks.
NOTE: Type 3
1. WARNING: Before beginning any service procedure in this section, refer to Safety Warnings
in section 100-00 General Information. Failure to follow this instruction may result in serious
personal injury.
Refer to: Gasoline and Gasoline-Ethanol Fuel Systems Health and Safety Precautions (100-00 General
Information, Description and Operation).
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 8 of 14
Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
4.
Connect
1.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 9 of 14
2.
Disconnect
NOTICE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove
any foreign material from the connector retaining clip area before separating from the tube or damage
to the tube or connector retaining clip may occur.
NOTICE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is
essential that absolute cleanliness is observed when working with these components or component
damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTICE: Do not use any tools. The use of tools may cause a deformity in the clip components which
may cause fuel leaks.
NOTE: Type 4
1. WARNING: Before beginning any service procedure in this section, refer to Safety Warnings
in section 100-00 General Information. Failure to follow this instruction may result in serious
personal injury.
Refer to: Gasoline and Gasoline-Ethanol Fuel Systems Health and Safety Precautions (100-00 General
Information, Description and Operation).
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 10 of 14
4.
5.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 11 of 14
Connect
1.
Disconnect
NOTICE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign
material from the connector retaining clip area before separating from the tube or damage to the tube or
connector retaining clip may occur.
NOTICE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is
essential that absolute cleanliness is observed when working with these components or component
damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTICE: Do not use any tools. The use of tools may cause a deformity in the clip components which
may cause fuel leaks.
NOTE: Type 5
1. WARNING: Before beginning any service procedure in this section, refer to Safety Warnings
in section 100-00 General Information. Failure to follow this instruction may result in serious
personal injury.
Refer to: Gasoline and Gasoline-Ethanol Fuel Systems Health and Safety Precautions (100-00 General
Information, Description and Operation).
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 12 of 14
Refer to: Fuel System Pressure Release (310-00C Fuel System - General Information - 2.0L EcoBoost
(184kW/250PS) - MI4, General Procedures).
4.
5.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 13 of 14
Connect
1.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015
Page 14 of 14
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ODY/~WSDS/US/EN... 3/2/2015