Professional Documents
Culture Documents
WT
KA
WT - 1
Notes on work
Caution JES002TA
• Nissan original aluminum wheels, because it is designed to fit the vehicle, that you do not use in other than the specified vehicle.
• Wheel nut of aluminum wheels to use the taper nut Nissan genuine parts.
• Be sure to use from taking the wheel balance. The balance of aluminum wheel weights, use the Arumihoi Lumpur for the weight of the Nissan genuine parts.
• Aluminum wheels, be very careful when handling in order to easily scratched. If you wash off the dirt, N only stone that contains the sand, wire brush or the like must
not be used. Detergent to use a mild detergent.
• After traveling on the road to spray the salt of the anti-freeze is, clean wash the wheel with water.
• When you wash the below and the car at the time of removal in the tire replacement, wash also the back of the wheel.
• When installing the wheel, mounted from wipe so that there is no dirt or foreign matter to the hub surface.
• Bolt, not oil to the absolutely adhere to the threaded portion and the seat surface of the nut of the nut.
• Or over the sharp protrusions while traveling, or riding to the curb and the sidewalk of the road, do not rely on or pickpocket.
• To prevent scratches on the aluminum wheel, to the outside to take the wheel cap after sandwiching a rag or cloth between the wheel and the wrench.
WT - 2
Load wheel tire
Appearance inspection
• Deformation to the load wheel, crack, damage, to check that there is no corrosion.
Runout inspection B
3. Attach the load wheel to the vehicle, the dial gauge, as shown in FIG. C
Set to check the deflection of the wheel.
Vertical deflection limit 0.3mm Less than 0.5mm Less than 1.5mm Less than D
Horizontal deflection limit 0.3mm Less than 0.8mm Less than 1.5mm Less than
Note: Steel wheels (including the emergency wheel) is A, B And shake the average value of the measured
FAA0118D
• When mounting the tire on the load wheels, applying a lubricant such as tire mount Lube to beat portion of the tire. In addition, after installation,
KA
WT - 3
Load wheel tire
removal
2. Away Kei agent (Sumitomo 3M No.4000 Double-sided tape burnished equivalent) is used to remove the double-sided tape remaining on the road wheels.
• After removal of the double-sided tape, than load wheel away Kei agent (Sumitomo 3M No.4000 Double-sided tape burnished or equivalent) be wiped off.
Adjustment
• Depending on the model of wheel balancers are those capable of mode setting for the paste weight, but to adjust to select the mode for the
weights implantation when working below.
1. Set the load wheel to the wheel balancer, to start the wheel balancer.
2. After each of the unbalance amount of the outer and the inner side is displayed, the unbalance amount of the displayed outer side
5/3 The hanging, selects the closest weight to this, mounting the weight on the outer side in the display position (angle).
Caution : Before you install the weight on the outer side, that you do not attach the weight of the inner side.
• If you choose to wait, the closest weight to the value that came out in the calculation that you select.
FAC1187D
• When attaching a weight to the load wheel, according to the steps of the wheel back as shown
in the figure, mounted so as to match the center of the wheel balancer indication position
(angle) WAIT.
• Weights for re-use can not part, that you do not re-use.
SEIA0031J
WT - 4
Load wheel tire
• Value that came out in the calculation 50g If it exceeds, as shown in FIG. Two Install it side-by-side sheets
Caution : Two If you are installing a piece of weight, taken piled the weight
Do not Attach.
B
Four. Unbalance amount and position displayed on the wheel balancer (angle)
In accordance with, kicking Attach the driving weight to the inner side of the road wheels.
FAC1189D
C
Five. Start the wheel balancer, the residual unbalance amount of the outer and the inner side of one side 10g Sure that is less than or equal to
To.
• Residual unbalance amount is one-sided 10g If it exceeds, perform again the same work from the beginning.
rotation JES002TD
• About to extend the life to prevent uneven wear of the tire 5,000km To exchange the position of the tire according to FIG for each run. Also, be inspected at the same time air pressure position
If the spare tire of the vehicle mounted tire (aluminum wheel mounted).
SEIA0214J
If spare A tire of emergency for tire and vehicle mounted tire (Suchiruho Eel installed).
I
SEIA0215J
KA
Caution : In the order of the diagonal line so as not to distort the wheel Two ~ Three Tightening divided into time. Acceptable residual unbalance
WT - 5
Service data
tire JES002LR
215 / 65R16 98S 220 {2.0} 220 {2.2} Except Highway Star
T155 / 70D17 420 {4.2} 420 {4.2} 2WD Car spare (for emergency)
WT - 6