Professional Documents
Culture Documents
SE Sheet
Driver's seat power seat ............................................... Five And removal, installation ................................... . . . twenty one
System FIG. ................................................. . . . . . .Five Seat back of decomposition, assembly .................... twenty one
System Overview .............................................. . . . . . .Five Decomposition of the sheet cushion, assembly ............. twenty four
E
· Component mounting position ....................................... ...... 6 Removing the second seat slide rail,
attachment .................................................. ...... twenty five
·circuit diagram .................................................. ............. Six
Multi-center seat slide rail up
Sheet switch input and output signal reference value ............. ...... 6
Remove, mounting ............................................. 26
- How to proceed with fault diagnosis ....................................... ...... 7
Third seat .................................................. .. . . . 28 F
And diagnosis before inspection ................................................. ...... 7
·Diagram .................................................. ....... . . . 28
- Phenomenon by fault diagnosis table ....................................... ...... 7
And removal, installation ................................... . . . 29
• The power circuit system inspection ................................................ Seven
Seat back of decomposition, assembly .................... 29
Switch system inspection ....................................... ...... 8
Decomposition of the sheet cushion, assembly ............. 31
Harness system inspection ....................................... ...... 8
G
Removing third seat slide rail, taken
Front seat ................................................ . . . . Ten
Attach .................................................. ....... . . . 32
SE
KA
SE - 1
Notes on work
SRS Air bag, care about the pre-tensioner seat belt with a car JIS006ZP
warning : • SRS The configuration of the associated air bag and pretensioner seat belt system components desorption and harness desorption, key
switch OFF In, disconnect the negative battery terminal Three It is carried out after leaving more than minute. (For discharging the electricity stored in the auxiliary power
• The desorption of the components, air tools and power tools, etc. that you do not use.
• SRS Air bag and harness for the pre-tensioner seat belt system is, that you do not repair by solder or the like. In addition, careful attention should be given to
interference with the biting and other parts of the harness.
• SRS That you do not use the electric tester such as circuit testers when the inspection of the air bag and pretensioner seat belt circuit and
separately state. (Working prevention by fine current of the tester)
• The connector of the air bag module and pre-tensioner seat belts, of foreign matter such as a driver plug is not. (Working preventing
electrostatic)
• SRS The airbag and pretensioner seat belt, using the yellow harness connector as identification, and to distinguish from other harness.
• For safety reasons, maintenance work, " SB Seat belt "and" SRS SRS Making reference to the air bag. "
• During removal and disassembly of the parts is damaged, performing in mind deformation. In addition, sites that appear to interference be protected by a rag or the like.
• Use a screwdriver or remove parts such (mating remove etc.) case, that the protection of each piece wrapped in cloth or plastic tape.
• It is replaced with a new one when you removed the re-unusable parts.
• After the completion of re-assembly is necessary to confirm that the function of each site is working properly.
- Water-soluble stains: A soft cloth dipped in warm water, wipe off the dirt part from squeeze hard. Then to wipe with
a soft cloth.
- Oily dirt: Lukewarm water to neutral detergent (concentration Two ~ Three % Within) was dissolved, wipe off the dirt portion a soft cloth dipped in the liquid. Then squeeze hard a
cloth soaked in fresh water, after wiping off to clean the detergent, to wipe with a soft cloth.
• Thinner, benzine, alcohol, organic solvents such as gasoline that you do not use.
• Leather seats is, to remove the dirt in the leather seat cleaner.
SE - 2
Clip list
List JIS004C1
SE
PIIA2121J
KA
SE - 3
Prepared by
name Use
ZZA1177D
Hoguringu
Seat trim pad mounting Each Nissan parts sales company
86901 32200
SE - 4
Driver's seat power seat
PIIA1686J
C
Slide adjustment to the driver's seat has set the power seat as possible.
D
Feature Description
Slide function
The seat can be adjusted back and forth by operating the slide switch of the cushion side portion.
E
DESCRIPTION OF OPERATION
circuit diagram
PIIA9646J
Slide operated H
• Slide switch One To turn terminal, it is powered at all times the supply.
• When you slide the slide switch in the forward direction, the slide switch Three Slide motor from turn terminal One Power is supplied to turn terminal in through
Ri motor, from the motor, slide motor Two Ban terminal, slide switch Four Ban terminal slide switch Two The circuit is formed by dropping the turn terminal as
the ground, rotate the motor, the sheet is advanced by allowing the slide screw times are rolling. SE
• When you slide the slide switch in the backward direction, the slide switch Four Slide motor from turn terminal Two Power is supplied to turn terminal in
through Ri motor, from the motor, slide motor One Ban terminal, slide switch Three Ban terminal slide switch Two The circuit is formed by dropping the turn
terminal as the ground, rotate the motor, sheet is retracted by causing the slide screw times are rolling. J
KA
SE - 5
Driver's seat power seat
PIIA1955J
slide SW Slide of the cushion side portion SW To control the slide motor by operating the
slide SW The motor is rotated by power supplied from, by rotating the slide screw and performs seat adjustment.
Slide motor
PIIA9646J
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW
SE - 6
Driver's seat power seat
3. The diagnosis before inspection is carried out. " Before diagnosis inspection "( SE-7 page ) See.
Four. From the phenomenon by fault diagnosis table, to repair or replace the cause of the failure. " Phenomenon by fault diagnosis Table "( SE-7 page ) reference. B
6. End
• Deformation or harness of the slide rail portion, malfunction due to foreign matter such as pinching. D
• Malfunction due to foreign matter such as adhesion of the slide motor and slide rail lead screw.
G
The power supply circuit system inspection JIS004A8
Inspection results
SE
OK » Two What
1. Slide switch vehicle side harness connector One Ban terminal ~ Body
Inspection results
OK »Normal
PIIA1919J
SE - 7
Driver's seat power seat
»harness
Measurement condition Voltage( V )
(+) (-)
Inspection results
OK » Two What
2. Slide switch Three Ban terminal ~ Two To measure the conduction between the turn terminal.
3. Slide switch Four Ban terminal ~ Two To measure the conduction between the turn terminal.
Inspection results
OK »Normal
2. Slide switch vehicle side harness connector Three Ban terminal - slide
Motor vehicle side harness connector One Check the continuity of turn terminal.
3. Slide switch vehicle side harness connector Four Ban terminal - slide
Motor vehicle side harness connector Two Check the continuity of turn terminal.
Inspection results
SE - 8
Driver's seat power seat
2. Slide switch vehicle side harness connector Two Ban terminal ~ Body
Inspection results
PIIA1920J
SE
KA
SE - 9
Front seat
Diagram JIS003HJ
Caution : When the sheet desorption, a site that appears to interfere with protected by a cloth, etc., possible to prevent scratches.
Manual sheet
PIIA1710J
SE - 10
Front seat
Four. Headrest holder (free type) Five. Headrest holder (rock type) Six Seat back pad
Ten. Armrest bracket 11. Seat cushion frame 12. Rear finisher cap
13. Rear finisher 14. Front seat slide cover 15. Lifter dial knob
16. Reclining lever knob 17. Outer finisher Eighteen Device inner cover
19. Adjust ASSY 20. Device inner cover twenty one. Inner finisher
B
twenty two. Front finisher twenty three. Armrest
SE
KA
SE - 11
Front seat
Power seat
PIIA1709J
Four. Headrest holder (free type) Five. Headrest holder (rock type) Six Seat back pad
SE - 12
Front seat
13. Rear finisher cap 14. Rear finisher 15. Front seat slide cover
16. Slide switch knob 17. Lifter dial knob Eighteen Reclining lever knob
19. Outer finisher 20. Device inner cover twenty one. Adjust ASSY
twenty two. Device inner cover twenty three. Inner finisher twenty four. Armrest
removal
Reference: Before, the rear seat is slid to the front seat Sly
C
Remove the lower side of the nails of the compartment cover, the cover before the vehicle is moved
PIIA1830J
2. To a position where the position and the tool body mounting bolts can be seen entering to slide the seat.
E
Four. Remove the connector and vehicle harness fixing clip of the power seat harness, remove from the vehicle.
F
Caution : During desorption, a site that appears to interfere with protected by a cloth, etc., possible to prevent scratches.
attachment
Caution : • To confirm that there is no biting of the carpet in the bolt holes in the slide leg before tightening the bolt.
• Seat slide, recline and operate smoothly, to make sure that there is no looseness or noise. G
• When the seat slide, by operating the reclining, wounded of harnesses, to make sure that there is no Setsuson.
1. Before tightening the anchor bolt, that the inner side and outer side of the slide rail is locked at the same position
To make sure.
H
2. Fit the harness connector and vehicle harness fixing clip.
3. The outer side slide rail rear of the nut of the temporary tightening.
Four. The outer side of the slide rail front of the anchor bolt is tightened.
SE
Five. The inner side of the slide rail front of the anchor bolt is tightened.
6. The slide rail rear of the anchor bolt on the inner side to this tightening.
KA
SE - 13
Front seat
Disassembly
1. Remove the bolt to open the armrest of the fasteners, remove the armrest.
2. Remove the clip of the front back garnish inside, the seat back
Because it takes the nail in the frame, remove while pulling down.
PIIA1717J
3. The push-up while knob the claws of the arrow portion of the figure, the headrest holder
BID1251D
Four. Attached to the seat back frame, outside the clip and retainer
Then, remove the seat back trim and pad.
PIIA1831J
assembly
Assembly is performed in reverse order of disassembly. Reference: When installing the Hoguringu, hog
Caution : • When the headrest holder mounting, left and right position and the front and rear direction
Be careful to come.
• When installing the seat back trim to the seat back frame, stretched well
wrinkles attach retainer, the clip.
PIIA1829J
SE - 14
Front seat
Disassembly
1. Remove the seat back trim and pad. " Seat back trim and pad "( SE-14 page ) See.
2. Remove the reclining device mounting bolts of the seat back frame, remove the seat back frame.
assembly B
Caution : After assembling the seat back frame, it always reclining device is to confirm that you want to operate.
Disassembly
1. Reclining lever knob causes the nail on the inside, slide the knob on the front side D
Remove by Ido.
BID1175D F
2. Hook the snap pin to the wire, remove it pulled up to the top, the lifter -
Remove the dial.
Four. Remove the cushion the back of the retainer, seat cushion trim and
Remove the pad.
H
Five. Remove the Hoguringu, remove the trim and pad.
Reference: When installing a new trim, old Hoguringu fixed position birds BID1272D
SE
assembly
Assembly is performed in reverse order of disassembly. Reference: When installing the Hoguringu, hog
• When to install a seat cushion trim to the seat cushion frame, attach
stretched well wrinkles. KA
PIIA1829J
SE - 15
Front seat
Disassembly
1. Removing the seat cushion trim and pad, the seat cushion
Down decomposition, assembly of the (manual sheet) One ~ Three After the procedure, remove the
2. Remove the cushion the back of the retainer, seat cushion trim and
Remove the pad.
Reference: When installing a new trim, old Hoguringu fixed position birds
assembly
Assembly is performed in reverse order of disassembly. Reference: When installing the Hoguringu, hog
• When to install a seat cushion trim to the seat cushion frame, attach
stretched well wrinkles.
PIIA1829J
Disassembly
1. Remove the seat cushion trim and pad. " Seat cushion trim and pad "( SE-15 page ) See.
2. Remove the mounting bolts, the seat cushion frame seat slide ASSY Remove more.
assembly
Assembly is performed in reverse order of disassembly.
SE - 16
Second seat
Diagram JIS003SY
Rotating seat
SE
KA
L
PIIA1711J
SE - 17
Second seat
Four. Headrest holder (free type) Five. Headrest holder (rock type) 6. Seat back pad
Ten. Rotate lever knob 11. Inner finisher 12. Seat cushion frame
13. Reclining device 14. Arm cover 15. Device outer cover
16. Slide lever knob 17. Reclining lever knob 18. The lower cover (right)
19. Leg cover (after) 20. Leg cover (ago) twenty one. The lower cover (left)
SE - 18
Second seat
SE
KA
PIIA1832J
Four. Sea back trim (lower) Five. Armrest 6. Headrest holder (free type)
7. Headrest holder (rock type) 8. Seat back trim (upper) 9. Seat back pad ASSY (upper) L
Ten. Folding device 11. Seat back frame (lower) 12. Seat cushion trim
SE - 19
Second seat
13. Medium broken lever 14. Free hinge cover 15. Armrest pad
16. Armrest trim 17. Reclining device 18. Device inner cover
19. Reclining lever knob 20. Slide lever knob twenty one. Device outer finisher
twenty two. The lower cover (right) twenty three. Seat cushion frame twenty four. Inner finisher
twenty five. Rotate lever knob 26. Leg cover (after) 27. The lower cover (left)
28. Leg cover (ago) 29. Cup holder 30. Turntable (turntable)
Multi-center seat
PIIA1713J
1. Cup holder 2. Seat back trim and pad 3. Seat cushion rear (Bakkurupo
Ket)
Four. Seat cushion trim and pad Five. Seat back frame 6. Free hinge cover
Ten. Seat cushion frame 11. Leg cover (ago) 12. Device arm cover (upper)
13. Device arm cover (lower) 14. Folding device finisher 15. Ahead of schedule lever knob
Shah
16. Device finisher 17. Reclining lever knob 18. Seat cushion hinge cover
SE - 20
Second seat
removal
Caution : During desorption, a site that appears to interfere with protected by a cloth, etc., possible to prevent scratches.
1. Remove the front and back of the seat slide lever (re unusable parts). (Multi-center seat only)
3. Remove the second seat mounting bolts, remove the second sheet.
PIIA1835J
attachment
Caution : To ensure that the seat back is locked. E
Four. To this tighten the rear-side slide rail outer mounting bolts.
6. Attach the front and back of the seat slide lever. (Multi-center seat only) G
1. Remove by pulling up on the snap ring on the top, outside the center-folding lever knob
It is.
SE
2. Open the armrest of the fasteners, remove the mounting bolts, Amure
Remove the strike.
PIIA1833J
KA
SE - 21
Second seat
BID1228D
6. After removal of the seat back (lower) trim and pad, to separate the trim and pad to remove the Hoguringu.
Reference: When installing a new trim, good workability and the Hoguringu fixed position keep the old trim reference.
7. Seat back ASSY Remove the mounting bolts of the (upper), the seat back ASSY Remove the (upper).
assembly
Assembly is performed in reverse order of disassembly. Reference: When installing the Hoguringu, hog
Caution : • When the headrest holder mounting, left and right position and the front and rear direction
Be careful to come.
• When installing the seat back trim to the seat back frame, attach stretched
well wrinkles.
PIIA1829J
Disassembly
1. Open the armrest of the fasteners, remove the mounting bolts, remove the armrest.
BID1228D
SE - 22
Second seat
Four. The seat back trim and pad to take the seat back frame
After removing, remove the Hoguringu, to separate the trim and pad.
Reference: When installing a new trim, old Hoguringu fixed position birds
BID1251D
assembly
C
Assembly is carried out in the reverse order of decomposition. Reference: When installing the Hoguringu, hog
Caution : • When mounting the headrest holder, left and right position and the front and rear of the
D
Be careful of the direction.
• When installing the seat back trim to the seat back frame, attach stretched
well wrinkles.
PIIA1829J
1. Remove the seat back trim and pad. " Seat back trim and pad (Comfortable captain sheet ) "
(SE-21 page ) , " Seat back trim and pad (rotating seat ) "( SE-22 page ) See.
G
2. Remove the slide lever knob.
PIIA1836J
SE
KA
PIIA1837J
Four. Remove the mounting screw of the outer finisher, remove the outer finisher. L
SE - 23
Second seat
6. Remove the mounting screw of the inner finisher, remove the inner finisher.
7. Remove the seat back frame mounting bolts, remove the seat back frame.
Reference: When assembling the seat back frame, make sure both sides lock of the reclining device, the bolt temporary tightening Oh
Door to be tightened.
assembly
Assembly is performed in reverse order of disassembly.
Caution : After assembling the seat back frame, it always reclining device is to confirm that you want to operate.
Disassembly
1. Remove the cup holder mounting screw, remove the cup holder.
2. Open the seat back trim and pad of fasteners, remove the seat back trim and pad.
assembly
Assembly is performed in reverse order of disassembly.
Disassembly
1. Remove the ahead of schedule lever knob (re unusable parts), remove the folding device finisher.
3. Remove free hinge, the device arm cover (upper), the device arm cover (lower).
Four. Seat back frame mounting bolts, remove the nut, remove the seat back frame.
assembly
Assembly is performed in reverse order of disassembly.
Disassembly
1. Seat back ASSY A remove. " Seat back frame "( SE-23 page ) See.
2. Remove the seat cushion the back of the retainer, remove the seat cushion trim and pad.
3. Remove the Hoguringu, to separate the seat cushion trim and pad.
assembly
Assembly is performed in reverse order of disassembly. Reference: When installing the Hoguringu, hog
Caution : Seat cushion ASSY The seat back ASSY When assembling to
PIIA1829J
SE - 24
Second seat
Disassembly
1. Remove the seat cushion trim and pad. " Seat cushion trim and pad "( SE-24 page ) See.
2. Remove the mounting bolts, remove from the turntable (turntable) the seat cushion frame.
assembly B
Disassembly C
2. Remove the seat cushion trim and pad mounting nut, remove the seat cushion trim and pad.
D
assembly
Assembly is performed in reverse order of disassembly.
E
Disassembly
1. Seat back ASSY A remove. " Seat back frame (multi-center seat ) "( SE-24 page ) See.
2. Remove the clip of the seat cushion rear (buckle pocket), taken a seat cushion rear (buckle pocket)
Rihazusu. F
3. Remove the screw and the clip of the cushion box finisher, remove the cushion box finisher,
Remove the seat cushion frame.
assembly
G
Assembly is performed in reverse order of disassembly.
SE
KA
PIIA1714J
SE - 25
Second seat
removal
1. Remove the second sheet. " Removal, installation "( SE-21 page ) See.
2. Remove the seat rail end cover, pull out and slide the seat rail finisher in the back-and-forth direction.
3. Turning the Carts pets and chip urethane, remove the second seat slide rail mounting bolts, the second sheet scan
Ride ASSY A remove.
attachment
Caution : Foreign matter on the floor before installing a slide rail (bis, washer earth) to make sure that does not fall.
Four. Attach the slide rail middle of the bolt on both sides.
Five. Attach the slide rail before the bolt on both sides.
PIIA1716J
1. Center slide rail (right) 2. Center slide rail (left) 3. Seat leg
removal
1. Remove the multi-center seat. " Removal, installation "( SE-21 page ) See.
2. Remove the front and back of the seat rail end cover.
3. Remove while sliding in the back-and-forth direction of the seat rail finisher.
Four. Carts pet, while lifting the chip urethane, remove the multi-center seat slide rail mounting bolts,
Remove the multi-center seat slide rail.
SE - 26
Second seat
attachment
Caution : • To ensure that the seat back is locked.
• That the inner side and outer side of the slide rail to make sure that you are locked in the same position.
B
3. Seat rail finisher, attach the seat rail end cover.
SE
KA
SE - 27
Third seat
Diagram JIS003T4
PIIA1712J
SE - 28
Third seat
Ten. Hinge cover 11. Reclining device cover 12. Hinge cover
13. Bumper rubber 14. Hinge connector 15. Reclining lever knob
19. Headrest holder (free type) Twenty Headrest holder (rock type) twenty one. Seat back frame
twenty two. undercover twenty three. Armrest twenty four. Free hinge cover
twenty five. Seat cushion frame 26. trim 27. Leg cover inner
B
28. Leg cover outer 29. Slide lever unit 30. Slide lever knob
C
removal
Caution : When the sheet desorption, protected by a cloth or the like to a site that appears to interference, possible to prevent scratches.
3. Sliding up springing up the third seat position. (From the foremost position Two , Three Stage)
E
Five. To release the catcher of the sheet striker of the inner slide, removing the third seat.
attachment
Caution : That sheet striker to make sure that you are locked securely to catcher
H
Decomposition of the seat back, assembling JIS003ZZ
Disassembly
SE
1. Remove the mounting bolt to open the armrest of the fasteners, remove the armrest. (Car with armrest)
KA
BID1228D
SE - 29
Third seat
3. The push-up while knob the claws of the arrow portion of the figure, the headrest holder
Four. Remove the seat back trim and pad from the seat back frame
It is.
Five. Remove the Hoguringu, to separate the seat back trim and pad.
Reference: When installing a new trim, old Hoguringu fixed position birds
BID1251D
assembly
Assembly is performed in reverse order of disassembly. Reference: When installing the Hoguringu, hog
Caution : • When the headrest holder mounting, left and right position and the front and rear direction
Be careful to come.
• When installing the seat back trim to the seat back frame, attach stretched
well wrinkles.
PIIA1829J
Disassembly
1. Remove the seat back trim and pad. " Seat back trim and pad "( SE-29 page ) See.
PIIA1847J
PIIA1838J
Four. Reclining device cover, hinge cover, hinge connector, the hinge cover lower removed.
Five. Remove the seat back frame mounting bolts of the reclining device.
SE - 30
Third seat
6. Remove the seat back hinge cover, E Remove the ring, remove the seat back frame.
assembly
Assembly is performed in reverse order of disassembly.
Caution : After assembling the seat back frame, it always reclining device is to confirm that you want to operate.
B
Decomposition of the seat cushion, assembly JIS00400
Disassembly
C
1. Seat back ASSY A remove. " Seat back frame "( SE-30 page ) See.
3. Seat cushion trim and retainer of the pad and, remove the Hoguringu, takes a seat cushion trim and pad D
remove.
PIIA1848J
Four. Remove the Hoguringu, to separate the seat back trim and pad.
Reference: When installing a new trim, good workability and the Hoguringu fixed position keep the old trim reference. G
assembly
Assembly is performed in reverse order of disassembly. Reference: When installing the Hoguringu, hog
SE
• When to install a seat cushion trim to the seat cushion frame, attach
stretched well wrinkles.
PIIA1829J
KA
SE - 31
Third seat
PIIA1715J
Four. Bumper rubber Five. Outer slide rail 6. Seat rail finisher
7. Inner slide rail 8. Seat rail end cover 9. Seat rail side finisher
removal
3. Remove while sliding to the rear direction of the seat rail finisher.
Four. Carpet, while lifting the chip urethane, remove the inner slide rail mounting bolts, the inner slide
Remove the rail.
1. Remove the third seat. " Removal, installation "( SE-29 page ) See.
2. Remove the rear side finisher lower. " EI Exterior and interior "of "Removing, mounting" ( EI-29 page ) See.
Four. Remove the outer slide rail mounting bolts, remove the outer slide rail.
SE - 32
Third seat
attachment
Caution : To make sure that foreign matter on the floor (bis, washer class) is not.
1. The slide rail inner front side of the bolt is temporarily tightened.
SE
KA
SE - 33
Third seat
SE - 34