Professional Documents
Culture Documents
Notes on work .................................................. .. ...... 3 - BCM Input and output signal reference value ................................. 34
- SRS Air bag, pre-tensioner seat Intelligent key unit input and output signal
Notes on belt with car .............................. Three Reference value .................................................. ....... . . . 34 C
Prepared by .................................................. .................. Four - How to proceed with fault diagnosis .......................................... 34
Special tools .................................................. ... . . . . . .Four - Phenomenon by fault diagnosis Chart .................................. 35
Combination meter .............................. . . . . . .Five Key insertion detection switch system (intelligent
- CAN Communication signal List ..................................... ...... 7 - Driver's door switch system ............................... 37
- How to proceed with fault diagnosis ....................................... . . . . 17 Front display unit input and output standards
And inspection of the power supply and the ground circuit ........................ . . . . 18 ·driver C / U Input and output reference value ....................... 43
Tachometer system ....................................... . . . .twenty one And correction of the reference line .............................................. . . . 46
Water temperature system .................................................. ... . . . .twenty two - How to proceed with fault diagnosis .......................................... 47
- Vehicle speed system .................................................. ... . . . .twenty two And diagnosis before inspection ................................................. . . . 47
· Needle of fuel gauge runout - Pointing error - There is a change ........ twenty three - Phenomenon by fault diagnosis Chart .................................. 48 H
And fuel gauge F It does not instruct ................................... twenty three - A / T The select lever " R " Also in the range
· Components inspection .............................................. . . . .twenty four Behind the video is not displayed ............................... 49
Of Combination meter removal, taken · Expected course line does not appear [ VDC , AFS With
System Overview .............................................. . . . . 27 And removal of the steering angle sensor, mounted ............. 55
JA
· Component mounting position ....................................... . . . . 27 Side blind monitor ................................. 56
And hydraulic warning light does not come on (key switch · Component mounting position .......................................... 57
Alarm (chime) .............................................. . . . . 30 Front display unit input and output standards
System Overview .............................................. . . . . 30 value .................................................. ................. Sixty
· Component mounting position ....................................... . . . . 32 ·driver C / U Input and output reference value ....................... Sixty
LB
·circuit diagram .................................................. ........... 33 · Image quality adjustment .................................................. ...... 61
·driver C / U Input and output signal reference value ............. . . . . 33 - CONSULT-II Function of ....................................... 61
DI - 1
· Self-diagnosis function .............................................. . . . 62 Side blind camera image is not displayed.
And correction of the reference line .............................................. . . . 64 . . . 70
And diagnosis before inspection .................................................. . . . 66 Side removal of the blind camera, take
And inspection of the power supply and the ground circuit ......................... . . . 66 Side blind camera C / U Removal of,
Side blind monitor on the screen is cut conversion attachment .................................................. ... . . . 73
DI - 2
Notes on work
SRS Air bag, care about the pre-tensioner seat belt with a car JKS00CMO
warning : • SRS The configuration of the associated air bag and pretensioner seat belt system components desorption and harness desorption, key
switch OFF In, disconnect the negative battery terminal Three It is carried out after leaving more than minute. (For discharging the electricity stored in the auxiliary power
• The desorption of the components, air tools and power tools, etc. that you do not use. B
• SRS Air bag and harness for the pre-tensioner seat belt system is, that you do not repair by solder or the like. In addition, careful attention should be given to
interference with the biting and other parts of the harness.
• SRS That you do not use the electric tester such as circuit testers when the inspection of the air bag and pretensioner seat belt circuit and
separately state. (Working prevention by fine current of the tester)
C
• The connector of the air bag module and pre-tensioner seat belts, of foreign matter such as a driver plug is not. (Working preventing
electrostatic)
• SRS The airbag and pretensioner seat belt, using the yellow harness connector as identification, and to distinguish from other harness.
D
• For safety reasons, maintenance work, " SB Seat belt "and" SRS SRS Making reference to the air bag. "
JA
DI
DI - 3
Prepared by
name Use
CONSULT-II
EG1187 0001
Diagnostic program card
EG1187 0100
(version JJD04B )
PBIA3527J
PBIA3526J
DI - 4
Combination meter
• The trip meter, Two It was adopted twin trip meter which can integrate the mode.
• The odometer trip switch was in the conventional combination meter in, divided into the trip the change-over switch and the trip reset switch, installed in the
combination meter on the right side. B
• Meter to integrate control each meter display C / U ASSY The adopted and incorporated in combination meters.
• Meter C / U ASSY Each meter and circuit check function which can check the circuit to the (speedometer, tachometer, fuel gauge, water temperature gauge), odometer, trip
meter, A / T Was built in the position display and segment check function and the remaining amount of fuel warning light check function can check the LCD Display of the
displayed by.
EL-4177D
• When you press the trip change-over switch, Ru button switches the mode is trip meter display.
• Trip A The trip reset switch in the display One When you press sec or more, trip A It is I
• If you remove the battery terminal, the integration of, but the integration of the
odometer is held trip meter is reset 0.0km become.
DI
DI - 5
Combination meter
ECCS C / U Is, the water temperature signal from a water temperature sensor and data conversion, meter C / U ASSY To send to. Meter C / U ASSY
Indicates the water temperature signal received in the water temperature gauge.
PKIA1836J
Tachometer
ECCS C / U It is an engine speed signal from the crank angle sensor and data conversion, the meter C / U ASSY To send to. Meter C / U ASSY Instructs
SKIA0923J
Fuel gauge
Meter C / U ASSY Processes the signal (resistance value) from the fuel gauge unit, and drives the fuel gauge.
Speedometer
ABS Actuator C / U ( VDC No car), or VDC / TCS / ABS C / U ( VDC Vehicle with) calculates a meter for vehicle speed based on the rectangular wave signal from the wheel speed
sensor, CAN Meter in communication C / U ASSY To send a vehicle speed signal to. Meter C / U ASSY
Converts the vehicle speed signal received, instructs the speedometer, further vehicle speed signal ( Two pulse, Eight pulse, CAN And it outputs a communication signal) to the other
control units.
SKIA8491J
Other than the manual mode of operation control valve ASSY - A / TC / U It is, CAN In communication A / T Meter shift position signal C / U ASSY To send
to. Combination meter, A / T Upon receiving the shift position signal, A / T Position to display.
DI - 6
Combination meter
BCM It is, A / T The shift up and down signal input from the control device (manual mode switch) CAN
Control valve in communication ASSY - A / TC / U To send to. Meter C / U ASSY It is, CAN Control valve in communication
ASSY - A / TC / U It received the manual mode display signal from, to display the shift position.
B
Car body shape coach
transmission A/T
C
Brake control ABS VDC ABS VDC
ECCS C / U ○ ○ ○ ○ ○ ○
transfer C / U ○ ○ ○
ABS Actuator - C / U ○ ○ F
Combination meter ○ ○ ○ ○ ○ ○
H
Intelligent key unit ○ ○ ○ ○ ○ ○
BCM ○ ○ ○ ○ ○ ○
IPDM E / R ○ ○ ○ ○ ○ ○
I
CAN Communication signal List JKS00O88
type One
●: Submit ○: reception
Comte roll JA
Combi Intelligent
back valve ABS Aku
Nesho key unit
The main signal name / Connection unit ECCS C / U Chue Tha C / BCM IPDM E / R
Down
ASSY - U
meter
A / TC / U
DI - 7
Combination meter
Comte roll
Combi Intelligent
back valve ABS Aku
Nesho key unit
The main signal name / Connection unit ECCS C / U Chue Tha C / BCM IPDM E / R
Down
ASSY - U
meter
A / TC / U
signal ( ABS ) ● ○
● ○
door SW signal ○ ○ ● ○
○ ●
Oil pressure warning signal
○ ●
● ○
ABS Warning light signal
● ○
Reference: Parking, reverse position signal only the received vehicle speed
DI - 8
Combination meter
Con Pre-clock
In Terri
To rush Con
Laser Adaptive Jefferies
Low Sea bi
VDC / radar cruise cement
Luba Tobe Steering Natick
TCS / sensor control key Yu
The main signal name / Connection unit ECCS valve belt angle tion BCM IPDM
C/U ABS C / systems nickel E/R
ASS sensor meter B
U To
Y-
C/U
A / TC C/U
reference One
/U
● ○
A / T Electronic control system warning signal
● ○
F
POWER Display signal ● ○
door SW signal ○ ○ ● ○
○ ●
Oil pressure warning signal
○ ●
G
Turn signal display signal ○ ●
DI - 9
Combination meter
Con Pre-clock
In Terri
To rush Con
Laser Adaptive Jefferies
Low Sea bi
VDC / radar cruise cement
Luba Tobe Steering Natick
TCS / sensor control key Yu
The main signal name / Connection unit ECCS valve belt angle tion BCM IPDM
C/U ABS C / systems nickel E/R
ASS sensor meter
U To
Y-
C/U
A / TC C/U
reference One
/U
● ○
ABS Warning light signal
● ○
Reference: One : Front seat emergency braking sensitive pre-crash seat belt attaching car only
type Four
●: Submit ○: reception
● ○
A / T Electronic control system warning signal
● ○
door SW signal ○ ○ ● ○
○ ●
Oil pressure warning signal
○ ●
DI - 10
Combination meter
● ○
ABS Warning light signal G
● ○
Pre-clock
Con
rush In Terri
To Con
VDC / Laser Adaptive Sea Jefferies
Transformer Low bi
TCS / radar cruise Tobe cement JA
file Luba Steering Natick
ABS C sensor control belt key Yu
The main signal name / Connection unit ECCS over valve angle tion BCM IPDM
C/U /U systems nickel E/R
ASS sensor meter
To
C/U Y-
C/U C/U
A / TC reference
/U One DI
DI - 11
Combination meter
Pre-clock
Con
rush In Terri
To Con
VDC / Laser Adaptive Sea Jefferies
Transformer Low bi
TCS / radar cruise Tobe cement
file Luba Steering Natick
ABS C sensor control belt key Yu
The main signal name / Connection unit ECCS over valve angle tion BCM IPDM
C/U /U systems nickel E/R
ASS sensor meter
To
C/U Y-
C/U C/U
A / TC reference
/U One
○ ○
reference reference
A / T Shift position signal ● ○ ○ ○
Three Two
● ○
A / T Electronic control system warning signal
● ○
door SW signal ○ ○ ● ○
○ ●
Oil pressure warning signal
○ ●
● ○
ABS Warning light signal
● ○
DI - 12
Combination meter
Pre-clock
Con
rush In Terri
To Con
VDC / Laser Adaptive Sea Jefferies
Transformer Low bi
TCS / radar cruise Tobe cement
file Luba Steering Natick
ABS C sensor control belt key Yu
The main signal name / Connection unit ECCS over valve angle tion BCM IPDM
C/U /U systems nickel E/R
ASS sensor meter
To
C/U Y-
C/U C/U
A / TC reference B
/U One
Reference: One : Front seat emergency braking sensitive pre-crash seat belt attaching car only
JA
DI
SKIB1311J
DI - 13
Combination meter
TKWA1966J
DI - 14
Combination meter
TKWA1967J
Combination meter (meter control unit ASSY ) Input and output signal reference value
E
JKS009VD
Measurement condition
Terminal
Signal name Keith Reference value( V )
number Operation or state
switch
F
One IGN Power supply ON - Power-supply voltage
36 CAN L - - -
37 CAN H - - -
38 Earth ON - about 0
I
ELF1080D
DI
ELF1084D
L
DI - 15
Combination meter
Measurement condition
Terminal
Signal name Keith Reference value( V )
number Operation or state
switch
about Five
44 Trip meter reset ON Trip reset SW ON (Pressed)
To signal OFF about 0
48 illumination SW ON - about 0
Earth
In diagnostic function, odometer, trip meter, A / T It has position display and adaptive cruise control system display segment check, the remaining amount of fuel warning
light check and meter control circuit and each meter (speedometer, tachometer, fuel gauge, water temperature gauge) the ability to check the conduction state of the .
1. While pressing trip change-over switch and the trip reset switch together, the key switch ON To.
2. Key switch ON rear, Five Releasing the trip change-over switch and the trip reset switch within seconds.
3. Odometer, trip meter, A / T Position display and adaptive cruise control system display of the segment is full lighting,
Also lit at the same time the remaining amount of fuel warning light. At this point, the meter C / U But switched to diagnostic mode.
SKIA2581J
DI - 16
Combination meter
Four. Press the trip reset switch. Normal at the time of, each meter and gauge while pressing the trip reset switch
There is displayed as shown in the figure. (In this case, the fuel level warning light is turned off.)
SKIB1312J
2. The diagnosis in accordance with the diagnostic flow do. " Diagnostic Flow "( DI-17 page ) See.
3. Than diagnostic results, to repair or replace the defect cause site. " Diagnosis"( DI-19 page ) See. F
Four. Or the meter is operating properly? In the case of normal Five What. If abnormalities Two What.
Five. Exit.
G
Diagnostic flow JKS009VH
2. Warning light class (engine warning light, oil pressure warning light, etc.) to see if lights.
) See.
Perform self-diagnosis of the combination meter. " Self-diagnostic procedures "( DI-16 page ) See.
NO Of »Combination meter BAT To check the power supply and ground circuit. " Inspection of the power supply and the ground circuit " (DI- DI
Eighteen page ) See. And, illumination control SW ASSY Inspect. " Illumination co trol switch ASSY "( DI-24 page ) See.
DI - 17
Combination meter
3. Segment check
Odo - Trip meter, A / T To confirm the position display and adaptive cruise control system display segment check display state. " Self-diagnostic
procedures "( DI-16 page ) See.
NO »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
Check the lighting condition of the remaining amount of fuel warning light. " Self-diagnostic procedures "( DI-16 page ) See.
Inspection results
OK » Five What
NG »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
NO »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
1. Fuse inspection
Or to check there is no blow to the following fuse combination meter.
One
IGN Power supply # Nine
Twenty
Reference: Sequence positions of the fuse " PG Power supply and ground circuit components "on "Fuses and fusible links" ( PG-4
page ) See.
Inspection results
OK » Two What
NG After »repair the cause site of fusing, to replace it with a new fuse. State
DI - 18
Combination meter
Remove the connector of the combination meter, check the voltage between the vehicle side harness
C
SKIA2651J
Inspection results
OK » Three What
D
3. Ground circuit inspection
Eighteen
38
SKIA8665J
Inspection results
OK »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
G
NG To repair »harness or connector.
Diagnosis JKS009VJ
H
phenomenon Estimated trouble place
Speedometer and odometer trip meter abnormally display " Vehicle speed line "( DI-22 page ) A reference
A / T Position display abnormally display " A / T Position display system "( AT-142 page ) A reference
Adaptive cruise control system display is abnormally display (car with adaptive cruise control Adaptive cruise control system "How to proceed with fault diagnosis" ( ACS-25
JA
system) page ) A reference
DI - 19
Combination meter
Fuel gauge
• Vehicle attitude, by the travel status, etc., because the fuel in the tank to move, there are times when the pointer swings.
• Key switch ON When you do the refueling in the state, the movement of the guidelines will be slower.
• Vehicle attitude, by the travel status, etc., because the fuel in the tank to move, there is a case in which the warning lamp lighting timing is changed.
INSPECTION
1. Connector inspection
2. Combination meter, connector and terminal of the fuel pump Complete (fuel gauge) (Mae
Ter side, unit side, missing the harness side), to check whether or not there is such bend.
Inspection results
OK » Two What
~ Fuel pump Complete (fuel gauge) vehicle side harness connector Two To check the
continuity between the turn terminal.
Inspection results
OK » Three What
DI - 20
Combination meter
~ Fuel pump Complete (fuel gauge) vehicle side harness connector Five To check the
continuity between the turn terminal.
Inspection results
OK » Four What
Perform a component inspection of the fuel gauge. " Fuel gauge "( DI-24 page ) See.
Inspection results E
OK » Five What
NG »Replace the fuel gauge. " Disassembly, assembly "( FL-6 page ) See.
Mounting of the fuel pump complete, and to check that there is no interference and caught the float arm and tank parts.
Inspection results
G
OK »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
SKIA0923J JA
INSPECTION
1. Visual inspection
DI
Tachometer at the time of starting the engine to make sure whether the swing.
Runout OK Or?
DI - 21
Combination meter
NO »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
3. ECCS C / U inspection
ECCS C / U Perform a self-diagnosis. " EC Engine control "of " CONSULT- Ⅱ Functions "( EC-51 page ) See.
Inspection results
OK »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
PKIA1836J
INSPECTION
1. ECCS C / U inspection
ECCS C / U Perform a self-diagnosis. " EC Engine control "of " CONSULT- Ⅱ Functions "( EC-51 page ) See.
Inspection results
OK »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
SKIA8491J
DI - 22
Combination meter
INSPECTION
B
Inspection results
OK »Meter C / U ASSY To exchange. " Disassembly, assembly "( DI-25 page ) See.
C
Needle of the fuel gauge runout - Pointing error - There is a change JKS009VQ
INSPECTION
D
1. Needle swing check of the fuel gauge
Or instruct change?
YES »Needle swing by the sloshing of the fuel tank can be considered. E
NO »To implement the fault diagnosis again of occurrence the details and confirmation from the customer.
F
INSPECTION
1. Interview 1
F Time to instruct pointed out how to make sure that too much of. G
NO » Three What
2. Inquiry Two
YES »When refueling the key switch OFF In to refuel. Key switch ON On the remains of the property F Instructions until
NO » Three What
JA
3. Inquiry Three
NO » Four What
DI - 23
Combination meter
YES »Carry out the inspection of the components. " Fuel gauge "( DI-24 page ) See.
NO »Interference of the float arm and tank parts in the fuel tank, caught and the like can be considered.
(disconnection).
Measurement condition
Conduction
SW name Operation and state
ON (Pressed) Yes
42 48 Dimming released SW SKIA2560J
OFF None
ON (Pressed) Yes
43 48 Trip switch SW
OFF None
ON (Pressed) Yes
45 48 Illumination Con
Troll SW (+) Side OFF None
ON (Pressed) Yes
46 48 Illumination Con
Troll SW (-)side OFF None
1. The fuel pump complete remove from the vehicle. " FL Fuel
Stem "of " The fuel gauge Fuel filter Fuyue-pumped ASSY "( FL-3 page ) See.
See.
Four. The fuel gauge Full State, Empty The state, the gauge side resistance SKIA2481J
To inspect the.
Reference: Full When Empty Position of the float of the ( mm ) Is a state in which hit the stopper. Terminal number
DI - 24
Combination meter
removal
1. Cluster lid A A remove. " IP Instrument panel "of "Removing, mounting" ( IP-5 page ) See.
2. screw( Four This) and harness connector ( Three Pieces) a disconnect, Con
PKIA1263J
D
attachment
Installation is carried out in the reverse order of removal.
SKIB2684J
Caution : When removing the clip, Be careful not to damage the front cover.
DI
DI - 25
Combination meter
removal
1. Cluster lid A A remove. " IP Instrument panel "of "Removing, mounting" ( IP-5 page ) See.
SKIB1313J
attachment
Installation is carried out in the reverse order of removal.
DI - 26
Warning light
• If an abnormality occurs in the oil pressure of the engine, it lights the hydraulic warning lamp.
• Oil pressure SW The hydraulic warning input directly from IPDM E / R But to convert, CAN Using a communication BCM To send the oil 圧警 tell signal to. BCM The oil
pressure warning signal was received CAN Use the communication, to send to the combination meter. Combination meter receives the oil pressure warning signal to turn
SKIA2482J
TKWA1968J
I
Oil pressure warning light does not come on (key switch ON Time) JKS009W9
To start the auto active test. " PG Power supply and ground circuit components "on "Auto Active Test" ( PG-23 JA
page ) See.
NO » Two What
DI
DI - 27
Warning light
CONSULT- Connect the Ⅱ, " IPDM E / R " of " self-diagnosis " I do.
Self-diagnosis result
SKIA1039J
CONSULT-II Connect, " BCM " of " self-diagnosis " I do. " CONSULTII Of function "( BCS-34
page ) See.
Self-diagnosis result
SKIA1039J
Shah SW Vehicle side harness connector One To check the continuity between the turn terminal.
Inspection results
Oil pressure SW Perform the component inspection. " Component inspection "( DI-29 page ) See.
Inspection results
OK » IPDM E / R To exchange.
DI - 28
Warning light
Oil pressure warning light does not go out (at the time of the hydraulic normal) JKS009WA
Reference: If you want the oil pressure inspection, " LU Lubrication systems " "Hydraulic inspection" ( LU-3 page ) See.
Four. Oil pressure SW Vehicle side harness connector One Ban terminal ~
Inspection results
SKIA2867J
OK » Two What
D
NG » Three What
2. Component inspection
Oil pressure SW Perform the component inspection. " Oil pressure SW "( DI-29 page ) See. E
Inspection results
OK » IPDM E / R To exchange.
Inspection results
OK » IPDM E / R To exchange.
I
Component inspection JKS009WB
Oil pressure SW
Oil pressure SW To check the continuity between ~ body earth.
JA
ELF0044D
DI - 29
Alarm (chime)
Feature Description
Forget key disconnect alarm (with intelligent key car, if you are using a mechanical key)
SKIA2517J
• Key insertion state (key insertion detection switch ON In), key switch ACC Or LOCK When the position, open the driver's door (door switch ON ) And the driver C / U There is
determined that the key forgetting to pull out, to operate the alarm buzzer (intermittent sound).
• Pull out the key during the alarm buzzer activated (key insertion detection switch OFF ) And, to release the actuation of the alarm buzzer.
• The key switch in the alarm buzzer working ON When you, or when you close the driver's door (door switch OFF ) To cancel the operation of the alarm buzzer.
For other type of alarm forgetting to reset key switch alarm (at the time of the intelligent key mobile) car with intelligent key, " BL Body lock security "of "System
Overview "
(BL-52 page ) See.
SKIA2518J
• Ignition knob ACC Or LOCK Position (push switch ON When), open the driver's door (door switch
ON ) And the intelligent key unit is judged to forget the return key switch, the buzzer output signal CAN In communication BCM To send the signal. BCM It is, body
this signal CAN Driver communication C / U To send to. At this time, the driver C / U Actuates an alarm buzzer (intermittent sound).
• Return the ignition knob in the alarm buzzer activated (push switch OFF ) And, to release the actuation of the alarm buzzer.
• The ignition knob in the alarm buzzer working ON When you, or when you close the driver's door (door switch OFF ) To cancel the operation of the alarm buzzer.
SKIA2519J
DI - 30
Alarm (chime)
• Key switch OFF ( LOCK ) Or ACC Light switch in position ON When, open the driver's door (door switch ON ) And the driver C / U There is determined that the light forgetting
to turn off, to activate the alarm buzzer (continuous sound).
• The light switch in the alarm buzzer working OFF When you, to release the actuation of the alarm buzzer.
• The key switch in the alarm buzzer working ON When you, or when you close the driver's door (door switch OFF ), To release the operation of the alarm buzzer. Reference: If the conditions to
operate key forgetting to pull out alarm and write forgetting to turn off the alarm at the same time, work and then write forgetting to turn off the alarm is priority
B
To do.
DESCRIPTION OF OPERATION
circuit diagram
C
TKWA1969J I
Forget key disconnect alarm (with intelligent key car, if you use a mechanical key) key insertion state (key insertion detection SW ON In), key switch ACC Or
LOCK When the position, rather than the driver's door open (door SW ON ) And activates the buzzer (intermittent sound).
JA
• 10A fuse(# Five Key plug from) SW (Key insertion detection SW ) Three Power supply voltage is supplied at all times to turn the terminal.
• Key is in the cylinder (key insertion detection SW ON ) When the key plug SW (Key insertion detection SW )
Four Through the turn terminal, driver C / U 10 Power is supplied to turn terminal.
• Driver's door is opened (the door SW ON A), driver C / U 20 Driver's door from turn terminal SW 1 It is grounded through the turn terminal.
DI
• Driver this time C / U Driver determines that detects that the driver's door is open, the key forgetting to pull out state C / U Activate the built have been buzzer (intermittent
sound) within.
Forgetting to reset key switch alarm (at the time of the intelligent key mobile phone) is the ignition knob ACC Or LOCK Position (push SW ON When), open the
DI - 31
Alarm (chime)
• 10A fuse(# One Key plug from) SW (push SW ) One Power supply voltage is supplied at all times to turn the terminal.
• Ignition knob is pressed (pushed SW ON ) When the key plug SW (push SW ) Two Intelligent key unit from turn terminal 27 Power is supplied to turn
terminal.
• Driver's door is opened (the door SW ON A), driver C / U 20 Driver's door from turn terminal SW 1 It is grounded through the turn terminal.
• Intelligent key unit, a signal driver's door is open CAN When detecting a communication, it is determined that the key switch back forgotten state, BCM To CAN Forgetting to reset the
key switch in the communication to send the alarm output signal.
• BCM Body an alarm output signal forgotten returns key switch CAN Driver communication C / U To send to.
Light forgetting to turn off the alarm key switch OFF ( LOCK ) Or ACC When the position, light SW But ON In, open the driver's door (door SW ON ) And
activate the buzzer (continuous sound). combination SW Reading function of (for more information " LT Lighting systems " "driver C / U Combination switch
reading function of "( LT-146 page ) See. By), of the tail lamp ON Driver a signal C / U 34 When the turn terminal is detected, BCM Headlights it is determined
• Driver's door is opened (the door SW ON ) And the driver C / U 20 Driver's door from turn terminal SW 1 It is grounded through the turn terminal.
• Driver this time C / U Driver determines that detects that the driver's door is open, the light forgetting to turn off state C / U To operate the built-in buzzer
(continuous sound) within.
SKIA2485J
• Key switch ( IGN ), Key insertion detection SW , Light SW , Driver's door SW More signal, forget key opener, to determine the
light forgetting to turn off, and outputs a forgotten alarm off key forgetting to pull out light.
driver C / U
• BCM Body from CAN By the key switch back forget alarm output signal that you entered in the communication, and outputs a forgotten
back key switch alarm.
Key switch ( IGN ) Signal, a body the key switch back forget alarm output signal from the intelligent key unit CAN
BCM
Using communication, driver C / U To send to.
Intelligent key unit push SW And the driver's door SW To determine the forgotten back key switch by the signal, Keith
The switch back forgotten alarm output signal CAN Using communication, BCM To send to.
DI - 32
Alarm (chime)
TKWA1969J
G
driver C / U Input and output signal reference value JKS009WD
Measurement condition
about 0
Ten Key insertion detection SW signal OFF Pull out the key
Insert the key about Twelve
I
13 B / CAN L - - -
14 B / CAN H - - -
combination SW Output5
twenty two ON Light, turn, wiper SW
But OFF State of
DI
SKIA2656J
DI - 33
Alarm (chime)
Measurement condition
combination SW Input4
34 ON Light, turn, wiper SW
But OFF State of
SKIA2655J
43 Earth ON - about 0
Measurement condition
49 B / CAN L - - -
52 CAN H - - -
53 Earth ON - about 0
63 B / CAN H - - -
65 CAN L - - -
Intelligent key unit input and output signal reference value JKS00CWG
Measurement condition
Two CAN H - - -
Three CAN L - - -
2. To grasp the system overview. " System Overview "( DI-30 page ) See.
3. Communicate diagnosis. " BCS Body Communication Systems " "Communication Diagnostics" ( BCS-40 page ) See.
Four. Do the inspection of the estimated failure point from the phenomenon by fault diagnosis Chart, to repair or replace the trouble place.
Five. Or alarm buzzer to operate properly? In the case of normal Six What. If abnormalities Three What.
6. Exit.
DI - 34
Alarm (chime)
Forget key opener, it does not work either light forgetting to turn off an alarm " Driver's door switch line "( DI-37 page ) A reference
• " Key insertion detection switch system (car with intelligent key ) "( DI-35
Key forgetting to pull out the alarm does not work (with intelligent key car, if you use
page ) A reference
the mechanical key)
• " Driver's door switch line "( DI-37 page ) A reference
B
• " Push switch line "( DI-36 page ) A reference
Forgetting to reset key switch alarm does not work (at the time of the intelligent key mobile) • " Key insertion detection switch system (car with intelligent key ) "( DI-35
page ) A reference
• " Driver's door switch line "( DI-37 page ) A reference
Key insertion detection switch system (with Intelligent Key car) JKS00B3E
D
1. Key insertion detection switch input signal inspection
Harness connector Ten To check the voltage between the turn pin-body earth.
F
Measuring terminal
Measurement condition Voltage( V )
(+) (-)
NG » Two What
Inspection results JA
OK » Three What
SKIA2897J
DI
DI - 35
Alarm (chime)
When you connect or disconnect the mechanical key, key plug SW (Key difference was included detection SW ) Three
Ban terminal ~ Four To check the continuity between the turn terminal.
Inspection results
INSPECTION
operation display
Return the ignition knob (state you remove your hand) OFF
Inspection results
NG » Two What
Inspection results
OK » Three What
To.
DI - 36
Alarm (chime)
terminal.
C
SKIA2901J
Inspection results
OK » Four What
D
Four. Push switch circuit inspection
2. Intelligent key unit vehicle-side harness connector 27 Ban terminal-key plug SW (push SW )vehicle
E
Side harness connector Two To check the continuity between the turn terminal.
Inspection results
G
OK »To replace the intelligent key unit. " Intel
Remove Li stringent key unit, mounting " (BL-112 PIIA2004J
page ) See.
Inspection results
DI
DI - 37
Alarm (chime)
2. Opening and closing the driver's door, driver C / U Vehicle side harness connector
Inspection results
SKIB1315J
NG » Three What
Vehicle side harness connector One To check the continuity between the turn terminal.
Inspection results
OK » Four What
2. Driver's door SW Vehicle side harness connector Three Ban terminal ~ Body
Inspection results
To. SKIA9189J
DI - 38
clock
Overview JKS009WK
• Air conditioning display section (Navi-free car only) and the overhead console unit Two It was
adopted a fluorescent tube display type digital watch in place.
• the above Two One watches because it is linked, and to adjust operation of the clock of the air
conditioning display section, is watch also adjusted the overhead console section. (Navi-free car)
B
• Adjustment operation information of the clock from the central switch, BCM In the treated body as
a clock data display signal CAN Overhead console part of the roof in the communication C / U It is
sent to. roof C / U It is to be displayed on the built by display the received signal. (Navi-free car)
C
PKIA1267J
• NAVI C / U from " Time " , " Minute " of GPS Time data BCM Type in,
BCM Body Watch as data display signal from CAN Roof overhead console section in communication C / U To send to. roof C / U It is, to be displayed on the display that
E
• RESET : ± Thirty Hour alignment of the minute. ( 1:00 ~ 1:29 If you press on 1:00 To, 1:30 ~ 1:59 If you press on 2:00 It is reset to. )
Caution : Car with navigation system, NAVI C / U from " Time " , " Minute " of GPS Due to the use of time data, tone
Say unnecessary.
Removal of the watch, for the installation, " ATC Auto air conditioner "of "Removing, mounting" ( ATC-69 Page ) ,as well as" EI Exterior and interior "of "Removing,
mounting" ( EI-35 page ) See.
JA
DI
DI - 39
Back-view monitor
• We set the back-view monitor that can check the rear of the vehicle in the front display at the time of recession.
• Image is well clear and visibility, easy to recognize the object, CCD Was employed camera (color).
• By combining the reference line from the car width and the rear end of the vehicle on the screen, it was easy to capture the sense of distance and the vehicle width sense of the vehicle behind
the object.
• To display the expected path of the vehicle in accordance with the steering angle of the steering wheel, parallel, it was easier to grasp the steering wheel at the time of parallel parking.
• Back view and can be displayed side blind monitor during the monitor display, it can be confirmed alternately left of the vehicle front-side and rear of the vehicle at the time of parallel parking and
the like.
• And can adjust the image quality adjustment in the back-view monitor screen, I tried to convenience.
DESCRIPTION OF OPERATION
• The front display unit is configured to supply power to the back-view camera, the control valve ASSY - A / TC / U ( BCM
Switches the screen to the camera image by the reverse signal from the via), to display overlay the reference line and warning Kokubun to back view camera video.
• The front display unit, the driver C / U ( BCM via) By the steering angle signal from the display of the expected course line that is linked to the steering angle.
System chart
SKIB1317J
DI - 40
Back-view monitor
SKIB1318J
JA
DI
DI - 41
Back-view monitor
TKWA1970J
DI - 42
Back-view monitor
Measurement condition
twenty three Camera video input ON A / T Select lever " R " range E
SKIA2558J
Measurement condition
Seven The steering angle signal One ON When steering When the right steering
SKIB1366J
Eight The steering angle signal Two ON When steering When the left steering
I
JA
SKIB1943J
DI
Nine The steering angle signal Three ON When steering
SKIB1944J
13 B / CAN L - - - L
DI - 43
Back-view monitor
Measurement condition
14 B / CAN H - - -
43 Earth ON - about 0
DI - 44
Back-view monitor
• Centralized switch in the back-view monitor screen ( NAVI Switch) part of " image quality " By pressing the switch, it is possible to adjust the image quality
(brightness, contrast, color saturation, hue) a.
• Adjustment operations, centralized SW ( NAVI SW ) Carried out in the part of the joystick. In addition, when dimming / non-dimming of the back-view monitor screen, it is possible to each of the
3. Centralized switch ( NAVI Switch) part of " image quality " Press the switch.
C
Four. Joystick ↑ ↓ Select the item you want to adjust in the operation, ← → operation
Five. If you continue to make the adjustment Four What. In the case of completing the adjustment Six What.
6. Centralized switch ( NAVI Switch) part of " Return " Press the switch, tone
D
Settling the end.
SKIA8496J
E
Overview
F
• And communication diagnosis in diagnostic function, there is a self-diagnosis menu mode.
• Communication diagnosis, to identify the communication abnormal part of the body communication system, to display the diagnostic results to the front display
and the overhead console section. (Detail is," BCS Body Communication Systems " "Self-diagnosis function ( CONSULT-II If you do not want to use the ) "( BCS-40 page
) See. )
G
• Self-diagnosis menu is possible to display the screen switch of each system to the front display, it can be called a self-diagnostic mode you need at the
touch of a button.
Diagnostic items
H
Diagnostic function Screen switch Diagnostic content
Communications Diagnostics - BCM And you can check the communication lines between the front display unit.
Communicating diagnosed by transmission and reception of data on the system network. Detail is "Mi communication
Cross-sectional "( BCS-40 page ) See.
I
The switch change of state of each switch is detected by the data on the network. Detail is
" Switch monitor "( BCS-44 page ) See.
Self-diagnosis menu mode
• Color bar display color shade confirmation by the color of the confirmation and gray scale display
by. For color bar display and a gray scale display, the navigation system "Confirmation - Adjustment
monitor mode "( AV-71 page ) See.
• It can be corrected in the back view monitor video display at the time of the reference line. Detail is "Correction of the
JA
reference line" ( DI-46 page ) See.
Communications Diagnostics
Operation procedure DI
How to Start and diagnostic result of the communication diagnosis, " BCS Body Communication Systems " "Communication Diagnostics" ( BCS-40 page )
See.
DI - 45
Back-view monitor
starting method
Five. Air conditioning OFF Press the switch, to stop the air conditioning.
6. While holding down the information switch, temperature control dial (right) Ten Within seconds
SKIA2767J
To Thirty Click to manipulate or more. Reference: The direction of rotation of the temperature control dial (right)
How to undo
• By variations in the mounting state of the camera, the vehicle width of the back-view monitor - When the distance guide lines and the back view monitor screen is deviated, the
self-diagnosis menu " monitor " Correction is performed using.
1. To create a correction line for correcting the screen. The rear of the vehicle floor, car
On both sides from the width 20 cm And the place of, from the rear end of the vehicle (bumper) 0.5 m ,
2. On the front display launch the self-diagnosis menu screen. " Own
His own diagnostic menu mode "( DI-46 page ) See.
Four. Joystick " Decision " The switch Three Press time, gray scale
And displays the display on the front display. Reference: continue " Decision " By
Reference: A / T The select lever " R " When placed in a range, the screen display
Display version information, color bar display, but may be in any state of
the grayscale display.
DI - 46
Back-view monitor
8. To move the entire reference line with the joystick, it was created on the floor correction La
So as to fit in in " Decision " Press the switch. If you want to save the settings, procedure Twelve What. If you want
to return the settings to the initial state (if you do not want to save), the procedure Eleven What. SKIA8497J
11. Joystick ↑ ↓ In operation, Reset Select the (reset), " Decision " After pressing the switch, procedure Three What. C
12. Joystick ↑ ↓ In operation, Store Select (Save), " Decision " After pressing the switch, A / T The select lever " P "
Back to the range.
13. Centralized switch ( NAVI Switch) part of " Return " Press the switch, after displaying the self-diagnosis menu screen, Kisui'
3. Check the phenomenon, to repair or replace the defect cause site. " Phenomenon by fault diagnosis Chart "( DI-48 page ) See.
Four. Make sure that the back-view monitor is operating normally, in the case of normal Five What. If abnormalities Two What.
F
G
1. BCM self-diagnosis
BCM Perform a self-diagnosis. " BCS Body Communication Systems " " CONSULT-II Of function "( BCS-34 page
) See.
H
Inspection results
OK » Two What
I
2. Communications Diagnostics
Communicate diagnosis. " BCS Body Communication Systems " "Communication Diagnostics" ( BCS-40 page ) See.
Inspection results
OK » Three What JA
Inspection results
OK »Inspection Exit
DI - 47
Back-view monitor
phenomenon References
" A / T The select lever " R " Behind the video does
A / T The select lever " R " Behind the video does not appear in the range. not appear in the range "( DI-
49 page )
DI - 48
Back-view monitor
A / T The select lever " R " Behind the video does not appear in the range JKS00B0N
phenomenon: A / T The select lever " R " Behind the video does not appear in the range.
Four. Back-view monitor camera vehicle side harness connector Two Ban terminal
Inspection results
OK » Two What
SKIA2572J
Front display unit vehicle-side harness connector Five , twenty three To check the continuity between the
Inspection results
OK » Three What
SKIA8662J
JA
DI
DI - 49
Back-view monitor
Four. Front display unit vehicle-side harness connector Five Turn end
Inspection results
OK » Four What
SKIA2573J
Five. Front display unit vehicle-side harness connector twenty three Turn
SKIA8498J
SKIA2558J
Inspection results
OK »To replace the front display unit. " Front display unit ASSY Removing, taken
Ri with "( AV-117 page ) See.
NG »To replace the back-view monitor camera. " Removing the back view monitor camera, mounting "( DI-
55 page ) See.
DI - 50
Back-view monitor
Expected course line does not appear [ VDC , AFS Cars with] JKS00NFW
Symptoms: back-view monitor not be the steering to display the expected course line at the time of display, will remain a guide line display.
Four. Steering angle sensor vehicle side harness connector Three Ban terminal ~ Body Architect
Inspection results
SKIB1606J
OK » Two What
D
NG To repair »harness or connector.
Steering angle sensor vehicle side harness connector Two To check the continuity between the turn pin-body E
earth.
Inspection results F
OK » Three What
SKIB1607J G
Angle sensor vehicle side harness connector Six , Seven , Eight To check the continuity between the turn
terminal.
Seven ~ Six I
9 ~ Eight
SKIB1608J
JA
3. driver C / U Vehicle side harness connector Seven , Eight , Nine Ban terminal ~ Bo
Inspection results
OK » Four What
SKIB1603J
DI - 51
Back-view monitor
Tar Seven , Eight , Nine To check the waveform between the turn pin-body earth.
SKIB1366J
SKIB1943J
SKIB1944J
Inspection results
OK »Driver C / U To exchange. "driver C / U Removal of, mounting "( BCS-90 page ) See.
NG »Steering angle sensor to replace the (spiral cable). "Spiral cable" ( SRS-20 page ) See.
DI - 52
Back-view monitor
Expected course line does not appear [ VDC , AFS No car] JKS00NFX
Symptoms: back-view monitor not be the steering to display the expected course line at the time of display, will remain a guide line display.
Four. Steering angle sensor vehicle side harness connector One Ban terminal ~ Body Architect
Inspection results
SKIB1600J
OK » Two What
D
NG To repair »harness or connector.
Steering angle sensor vehicle side harness connector Three To check the continuity between the turn pin-body E
earth.
Inspection results F
OK » Three What
SKIB1601J G
Angle sensor vehicle side harness connector Four , Two , Five To check the continuity between the turn
terminal.
Seven ~ Four I
9 ~ Five
SKIB1602J
JA
3. driver C / U Vehicle side harness connector Seven , Eight , Nine Ban terminal ~ Bo
Inspection results
OK » Four What
SKIB1603J
DI - 53
Back-view monitor
Compactors Seven , Eight , Nine To check the waveform between the turn pin-body earth.
SKIB1366J
SKIB1943J
SKIB1944J
Inspection results
OK »Driver C / U To exchange. "driver C / U Removal of, mounting "( BCS-90 page ) See.
NG »Steering angle sensor to replace the (spiral cable). "Spiral cable" ( SRS-20 page ) See.
DI - 54
Back-view monitor
removal
1. Remove the roof spoiler. " EL Exterior and interior "of "Removing, mounting" ( EI-25 page ) See.
2. Insert a flat-blade screwdriver or the like winding a tape, back view mode
Remove the Nita camera Hui nickel Shah.
B
PKIA1268J
D
3. Mounting screw ( Two Remove the book), taken a back view monitor camera
Rihazusu.
F
PKIA1269J
attachment
Mounting, it is carried out in the reverse order of removal.
G
Removal of the steering angle sensor, mounted JKS00NFY
Steering angle sensor (spiral cable) removal, for more information about mounting " SRS Occupant protection device "of "Spiral cable" ( SRS-20 page ) See.
JA
DI
DI - 55
Side blind monitor
• Embedded into the left door mirror CCD By the camera, set the side blind monitor that can check the vehicle left front-side on the display.
• Image is well clear and visibility, easy to recognize the object, infrared CCD Was employed camera (color).
• In order to ensure visibility at night, CCD Camera to the auxiliary lighting (infrared LED ) Was adopted.
• By synthesizing the reference line on the display, and to facilitate the grasping of the vehicle front left-side portions.
• And can display the back view monitor in the side blind monitor display, it can be confirmed alternately left of the vehicle front-side and rear of the vehicle at the time of parallel parking and the
like.
• The image quality adjustment and can be adjusted in the side blind monitor display screen, tried to convenience.
DESCRIPTION OF OPERATION
• Front Deisupurei unit, centralized SW ( NAVI SW Side blind monitor from) SW By the signal input, side blind camera C / U Side blind monitor ON To
send a signal.
• Side blind camera C / U It is, side blind monitor from the front Deisupurei unit ON Signal by, and supplies power to the side blind camera and auxiliary
lighting, to send a camera video switching signal to the front display unit.
• Side blind camera C / U Combines the reference line in the camera image input from the side blind camera outputs a video signal in the front
display unit.
• The front display unit, side blind camera C / U By the camera video switching signal from, switch the composite signal to the side blind monitor. In
addition, to draw overlay a warning statement to the side blind camera video input.
• Front Deisupurei unit, side blind monitor SW About from entering the signal Three When the minute elapsed, rhino de blind camera C / U Side
blind monitor OFF To send a signal.
System chart
SKIB1320J
DI - 56
Side blind monitor
SKIB1319J
JA
DI
DI - 57
Side blind monitor
TKWA1971J
DI - 58
Side blind monitor
Side blind camera C / U Input and output signal reference value JKS00NG0
Measurement condition
Four Supplemental lighting LED (+) ON Side blind monitor ON Time about Five
about Six C
Six Camera power output ON Side blind monitor ON Time
Side blind monitor OFF Time about 0
about 0
Sixteen Camera video switching signal ON Side blind monitor ON Time
Side blind monitor OFF Time about Five
E
19 Video signal (-) - - -
SKIA8050J
SKIA8050J
JA
DI
DI - 59
Side blind monitor
Measurement condition
Seven The video input signal (+) ON Side blind monitor ON Time
SKIA8050J
about 0
Eight Camera video switching signal ON Side blind monitor ON Time
Side blind monitor OFF Time about Five
Ten Earth ON - -
Measurement condition
13 B / CAN L - - -
14 B / CAN H - - -
43 Earth ON - about 0
DI - 60
Side blind monitor
• Concentration in the side blind monitor screen SW ( NAVI Switch) part of " image quality " By pressing the switch, it is possible to adjust the image quality
(brightness, contrast, color saturation, hue) a.
• Adjustment operations, centralized SW ( NAVI SW ) Carried out in the part of the joystick. In addition, when dimming / non-dimming side blind monitor screen, it is possible to each of the
3. Concentration SW ( NAVI Switch) part of " image quality " Press the switch.
C
Four. Joystick ↑ ↓ Select the item you want to adjust in the operation, ← → operation
Five. If you continue to make the adjustment Four What. In the case of completing the adjustment Six What.
6. Concentration SW ( NAVI Switch) part of " Return " Press the switch, adjustment end.
D
SKIB1393J
E
CONSULT-II It is, side blind camera C / U By communicating with to perform the following functions.
F
Diagnostic site Inspection items, diagnostic mode Content References
Work support You can adjust the position of the guide lines superimposed on the camera image. (DI-62)
Side blind monitor
Data Monitor * - -
To.
JA
SKIB1321J
DI
DI - 61
Side blind monitor
2. " Diagnostic mode selection " On screen " Work support " , Or " C / U part number "
The touch.
SKIA4951J
Work support
Operation procedure
1. " Diagnostic mode selection " On screen " Work support " The touch.
2. " Select work item " On screen " Reference line pattern selection " Or " A guide line position fine-tuning " The touch.
Reference line pattern selection The inclination of the reference line Three It can be selected from the pattern. ( 0 ~ Two of Three pattern)
A guide line position fine-tuning You can fine-tune the reference line up, down, left, or right.
For more information " Correction of the reference line "( DI-64 page ) See.
Overview
• Communication diagnosis, to identify the communication abnormal part of the body communication system, to display the diagnostic results to the front display
and the overhead console section. (Detail is," BCS Body Communication Systems " "Self-diagnosis function ( CONSUL T - II If you do not want to use the ) "( BCS-40 page
) See. )
• Self-diagnosis menu, and display the screen switch of each system to the front display, can be called a self-diagnostic mode you need at the
touch of a button.
Diagnostic items
Communications Diagnostics - BCM And you can check the communication lines between the front display unit.
Communicating diagnosed by transmission and reception of data on the system network. Detail is "Mi communication
Cross-sectional "( BCS-40 page ) See.
Self-diagnosis menu mode
The switch change of state of each switch is detected by the data on the network. Detail is
" Switch monitor "( BCS-44 page ) See.
Communications Diagnostics
Operation procedure
How to Start and diagnostic result of the communication diagnosis, " BCS Body Communication Systems " "Communication Diagnostics" ( BCS-40 page )
See.
DI - 62
Side blind monitor
starting method
Five. Air conditioning OFF Press the switch, to stop the air conditioning.
6. While holding down the information switch, temperature control dial (right) Ten Within seconds C
SKIA2767J
To Thirty Click to manipulate or more. Reference: The direction of rotation of the temperature control dial (right)
How to undo
JA
DI
DI - 63
Side blind monitor
Overview
By variations in the mounting state of the camera, when the side blind monitor vehicle left front-side reference line and the side blind monitor screen of
is deviated CONSULT-II It is corrected using.
1. To create a correction line for correcting the reference line of the monitor.
To the left front of the vehicle, from the front tire (left) 35cm Left, and from the front Tobanpa front end 30cm
SKIA7976J
2. CONSULT-II Connect, " Diagnostic system selection " On screen " Saidobura
India Monitor " The touch. Reference: • " Side blind monitor " If you select, display
Screen conversion Waru cut to automatically side blind monitor the video.
• CONSULT-II If the connection at the time, was switched from the side blind monitor
the video on the screen, such as a map, " Return " It switched to the side blind monitor
• CONSULT-II When connected, warning statement in the side blind monitor the video is SKIB1322J
not displayed.
3. " Select work item " On the screen, " Reference line pattern selection " The touch.
SKIA8114J
DI - 64
Side blind monitor
Four. " U P " Or " DOWN " Touch, something close to the correction line " putter
Nshingou 0 , One Or Two " of Three pattern Select from the reference line. At this time, to select the one that
Five. " writing " Touch, to determine the pattern of the reference line.
SKIB1394J
6. " Select work item " On the screen, " A guide line position fine-tuning " The touch. C
SKIA8114J E
7. To fit the correction line that you created, " X U P " , " X DOWN " , " Y U P " , " Y
F
Adjustment direction Setting monitor
G
8. Align the reference line to the correction line " writing " Touch, the position of the reference line
Determine.
SKIB1395J
H
Caution : " Reference line pattern selection " as well as " A guide line position fine-tuning " If you change the settings in the, " writing " If you do not touch the following
2. Performing a diagnostic before inspection. "Diagnosis before inspection" ( DI-66 page ) See.
3. Check the phenomenon, to repair or replace the defect cause site. " Phenomenon by fault diagnosis Chart "( DI-66 page ) See.
JA
Four. Side blind monitor is to confirm that you want to operate normally, in the case of normal Five What. If abnormalities Two What.
DI
DI - 65
Side blind monitor
1. BCM self-diagnosis
BCM Perform a self-diagnosis. " BCS Body Communication Systems " " CONSUL T - II Of function "( BCS-34 page
) See.
Inspection results
OK » Two What
2. Communications Diagnostics
Communicate diagnosis. " BCS Body Communication Systems " "Communication Diagnostics" ( BCS-40 page ) See.
Inspection results
OK »To 3
Inspection results
OK »Inspection Exit
phenomenon References
1. Fuse inspection
Side blind camera C / U To check whether the there is no blow to the following fuse.
Reference: Sequence positions of the fuse, " PG Power supply and ground circuit components "on "Fuses and fusible link "
(PG-4 page ) See.
Inspection results
OK » Two What
NG After »repair the cause site of fusing, to replace it with a new fuse.
DI - 66
Side blind monitor
2. Side blind camera C / U Vehicle side harness connector One , Two Turn
Inspection results
C
OK » Three What
SKIA7979J
2. Side blind camera C / U Vehicle side harness connector Three Turn end
Inspection results
OK »Inspection end.
F
NG »Side blind camera C / U To repair the ground circuit
That.
SKIA7980J
G
Side blind monitor on the screen is not switched. JKS00NLQ
Symptoms: side blind monitor SW Even if you press the, the screen is not switched to the side blind monitor.
INSPECTION
H
See.
I
Inspection results
OK » Two What
JA
2. Side blind monitor SW inspection
" Switch monitor " Side blind monitored by SW To confirm the operation. " BCS Body communication system "of "Switch Monitor" ( BCS-44 page ) See.
DI
Inspection results
OK » Three What
NG »Intensive SW ( NAVI SW ) To exchange. "Centralized switch ( NAVI Removing the switch), mounting " (AV-117
page ) See.
L
DI - 67
Side blind monitor
2. Side blind monitor SW Side blind mosquito when you press the
Mera C / U Vehicle side harness connector Eight To check the voltage between the turn pin-body
earth.
OK » Five What
NG » Four What
3. Side blind camera C / U Vehicle side harness connector Eight Turn end
Child-driver C / U Vehicle side harness connector Twelve To check the conduction between the turn terminal.
Four. Side blind camera C / U Vehicle side harness connector Eight Turn end
Inspection results
OK »Driver C / U To exchange. "driver C / U Removal of, mounting "( BCS-90 page ) See.
grounding.
SKIA8402J
Inspection results
NG » Six What
DI - 68
Side blind monitor
3. Side blind camera C / U Vehicle side harness connector Sixteen Turn end
B
Child-front display unit vehicle-side harness connector Eight
To check the continuity between the turn terminal.
C
Four. Side blind camera C / U Vehicle side harness connector Sixteen Turn end
Inspection results D
OK » Seven What
1. The key switch OFF To, co-of the front display unit
To connect the connector.
3. Side blind camera C / U Vehicle side harness connector Sixteen Turn end
JA
DI
DI - 69
Side blind monitor
Symptoms: side blind monitor SW When you press, the screen cut switched but the camera image is not displayed.
earth.
Inspection results
twenty three , twenty four Ban terminal - electric mirrors (left) the vehicle side harness connector Six ,
Fifteen , Sixteen , Seven To check the continuity between the turn terminal.
Six ~ Six
Seven ~ 15
: Yes conduction
23 ~ 16 24 ~ Seven
SKIB1933J
Four. Side blind camera C / U Vehicle side harness connector Six , Seven ,
twenty three , twenty four To check the continuity between the turn pin-body earth.
Six , Seven , twenty three , twenty four ~ Body earth: None conduction
Inspection results
OK » Three What
SKIA8406J
DI - 70
Side blind monitor
SKIA8050J SKIA8408J
Inspection results D
OK » Four What
NG » Six What
Ban terminal-front display unit vehicle side Hanesukoneku ter Six , Seven To check the continuity
19 ~ Six G
: Yes conduction
Twenty ~ Seven
Four. Side blind camera C / U Vehicle side harness connector 19 , Twenty SKIB1629J
Inspection results
OK » Five What
I
NG To repair »harness or connector.
JA
DI
DI - 71
Side blind monitor
1. Side blind camera C / U And to connect the connector of the front display unit.
earth.
SKIA8050J SKIA8410J
Inspection results
Inspection results
2. Disassemble the electric mirror (left), remove the side blind camera.
" GW Glass-window-mirror "of "Decomposition, assembly" ( GW-70
page ) See.
Measuring terminal
connector connector
One Seven
Two Sixteen
Yes
Six Six
Seven Fifteen
SKIB2142J
DI - 72
Side blind monitor
removal
1. Remove the passenger side of the door mirror. " GW Door mirror "of "Removing, mounting" ( GW-69 page ) See.
2. Disassemble the passenger side of the door mirror, side turn signal lamp [auxiliary lighting (infrared LED ) And remove the piece.
3. screw( Two Remove the book), remove the side blind camera.
D
SKIB1324J
attachment
Installation is carried out in the reverse order of removal.
E
removal
1. Remove the instrument lower panel. " IP Instrument panel "of " Instrument ASSY " (IP-4 page ) See. F
2. Remove the parking brake pedal. " PB Parking brake "of the "Removing, mounting" ( PB-4 page )
G
Four. Remove the connector.
SKIB1325J
I
attachment
Installation is carried out in the reverse order of removal.
JA
DI
DI - 73
Side blind monitor
DI - 74