Professional Documents
Culture Documents
1. SCOPE
This document is dedicated to the description of the process to select the most suitable lube oil type,
according to the machinery train composition and ambient temperature. It contains a guideline to
perform this selection.
2. REFERENCE DOCUMENTS
ITN52220.02 Turbo-machinery Lubricating Oil Recommendations: Gas Turbines with Bearing Ambients
below 260°C (500°F); Steam Turbines; Electric Motors and Generators, Axial and centrifugal
compressors; load gears
ITN52220.03 Turbo-machinery Lubricating Oil Recommendations: Gas Turbines with Bearing Ambients
Above 260°C (500°F); Steam Turbines; Electric Motors and Generators, Axial and centrifugal
compressors; load gears
Saturated
Sulfur Hydrocarbons
Group VI (1) wt % wt % Production process
Mineral oil derived from natural
80-
I 119 >0.03 <90 hydrocarbon source
Mineral oil derived from natural
80-
II 119 <0.03 >90 hydrocarbon source
Mineral oil derived from natural
III ≥ 120 <0.03 >90 hydrocarbon source
Poly Alpha Olefins (PAO) derived by
chemical synthesys from natural hydrocarbon
IV source
Chemical Synthesis
V All base stocks not in Groups I-IV
4. LUBE OIL CATEGORIES (for a detailed lube oil type selection guideline refer to par. 5)
mineral oil properties according to ITN52220.02: for gas turbines with bearings ambient
temperature below 260°C and relevant driven equipment (e.g. centrifugal or axial compressors
and electric generators) with or without load gears. This category of lube oils is valid also for
expanders, electric motors and steam turbines as drivers. However, when a steam turbine is
present in combined cycle with a gas turbine, to promote oil commonality, it is recommended
to refer to par. II of the present (both for common or separate oil supply systems).
Synthetic hydrocarbon oils described at par. 4.2 have superior performance so they are for sure
acceptable also for those less severe applications where a standard resistance to thermal
degradation could be enough.
4.1.2. “A n t i - w e a r ” c a t e g o r y - f o r m i n i m u m a m b i e n t t e m p e r a t u r e ≥ 0 ° C a n d i n c a s e o f a l o a d
gear presence
4.1.3. “High water separability” category – for minimum ambient ≥ 0°C and in case the
driver is a steam turbine
4.1.4. “ H i g h w a t e r s e p a r a b i l i t y ” a n d “a n t i - w e a r ” c a t e g o r y - f o r m i n i m u m a m b i e n t t e m p e r a t u r e
≥ 0°C, in case the driver is a steam turbine and there is a load gear in the machinery train
4.2. Mineral or Synthetic Hydrocarbon oils ISO VG 32 high resistance to thermal degradation:
mineral oil according to ITN52220.03: for gas turbines with bearings ambient temperature
greater than 260°C and relevant driven equipment (e.g. centrifugal or axial compressors and
electric generators) with or without load gears. This category of lube oils is valid also for
steam turbines used in combined cycle with a gas turbine, both for common or separate oil
supply systems.
STANDARD PERFORMANCE:
4.2.2. “L o w P o u r P o i n t ” ( L P P ) c a t e g o r y – f o r m i n i m u m a m b i e n t
4.2.3. “A n t i - w e a r ” c a t e g o r y - f o r m i n i m u m a m b i e n t t e m p e r a t u r e ≥ 0 ° C a n d i n c a s e o f a l o a d
gear presence
REVISION DESCRIPTION: NO REVISION INCLUDED IN THIS SHEET DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 2 of 12
4.2.4. “L o w P o u r P o i n t ” ( L P P ) a n d “a n t i - w e a r ” c a t e g o r y - f o r m i n i m u m a m b i e n t t e m p e r a t u r e
-2 0 ° C ≤ m i n T a m b < 0 ° C a n d i n c a s e o f a l o a d g e a r p r e s e n c e
4.2.5. “H i g h w a t e r s e p a r a b i l i t y ” - f o r m i n i m u m a m b i e n t t e m p e r a t u r e m i n T a m b ≥ 0 ° C
4.2.6. “H i g h w a t e r s e p a r a b i l i t y ” a n d “L o w P o u r P o i n t ” ( L P P ) c a t e g o r y – f o r m i n i m u m
ambient temperature -20°C ≤ min Tamb < 0°C
4.2.7. “H i g h w a t e r s e p a r a b i l i t y ” a n d “A n t i - w e a r ” c a t e g o r y - f o r m i n i m u m a m b i e n t
temperature ≥ 0°C and in case of a load gear presence
4.2.8. “H i g h w a t e r s e p a r a b i l i t y ”, “ L o w P o u r P o i n t ” ( L P P ) a n d “ a n t i - w e a r ” c a t e g o r y - f o r
minimum ambient temperature -20°C ≤ min Tamb < 0°C and in case of a load gear
presence
In case we need the lowest tendency to form varnish and so the highest performance in terms
of oxidation resistance and the maximum solubility of the base oil towards thermal degradation
sub-products. The use of this kind of oil is mainly recommended for those applications where
s e r v o - v a l v e s h y d r a u l i c a l l y a c t u a t e d b y h i g h p r e s s u r e o i l a r e p r e s e n t . T h e s e s e r v o -v a l v e s a r e
mainly used to actuate Inlet Guide Vane (IGV), Nozzles Guide Vane (NGV) and gas valves. For
a m o r e d e t a i l e d e x p l a n a t i o n o f l o w- v a r n i s h i n g o i l s c h a r a c t e r i s t i c s r e f e r t o p a r . X V i n
ITN52220.03
4.2.9. “L o w - v a r n i s h i n g ” - f o r m i n i m u m a m b i e n t t e m p e r a t u r e m i n T a m b ≥ 0 ° C .
4.2.10. “L o w - v a r n i s h i n g ” a n d “L o w P o u r P o i n t ” ( L P P ) c a t e g o r y – f o r m i n i m u m a m b i e n t
temperature -20°C ≤ min Tamb < 0°C
4.2.11. “L o w v a r n i s h i n g ” a n d “A n t i - w e a r ” c a t e g o r y - f o r m i n i m u m a m b i e n t t e m p e r a t u r e ≥ 0 ° C
and in case of a load gear presence
4.2.12. “L o w v a r n i s h i n g ”, “L o w P o u r P o i n t ” ( L P P ) a n d “a n t i - w e a r ” c a t e g o r y - f o r m i n i m u m
ambient temperature -20°C ≤ min Tamb < 0°C and in case of a load gear presence
4.2.13. “H i g h w a t e r s e p a r a b i l i t y ” a n d “L o w v a r n i s h i n g ”- f o r m i n i m u m a m b i e n t t e m p e r a t u r e
min Tamb ≥ 0°C
4.2.14. “H i g h w a t e r s e p a r a b i l i t y ”, “L o w v a r n i s h i n g ” a n d “L o w P o u r P o i n t ” ( L P P ) c a t e g o r y –
for minimum ambient temperature -20°C ≤ min Tamb < 0°C
4.2.15. “H i g h w a t e r s e p a r a b i l i t y ”, “L o w v a r n i s h i n g ” a n d “A n t i -w e a r ” c a t e g o r y - f o r m i n i m u m
ambient temperature ≥ 0°C and in case of a load gear presence
4.2.16. “H i g h w a t e r s e p a r a b i l i t y ”, “L o w v a r n i s h i n g ”, “L o w P o u r P o i n t ” ( L P P ) a n d “a n t i - w e a r ”
category - for minimum ambient temperature -20°C ≤ min Tamb < 0°C and in case of a
load gear presence
mineral oil according to ITN52220.02 - for steam turbines, expanders and electric motors as
drivers and relevant driven equipments (e.g. centrifugal or axial compressors and electric
generators) with or without load gears. This viscosity grade category could be used also when
the driver is a gas turbine and the ambient temperature is so high that it is no possible to
maintain the lube oil header at 55°C with an air cooling system. Before taking a decision it
could be necessary to perform a rotordynamic assessment for the gas turbine.
REVISION DESCRIPTION: MODIF. LOW VARNISHING DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 3 of 12
Synthetic hydrocarbon oils described at par. 4.4 have superior performance so they are for sure
acceptable also for those less severe applications where a standard resistance to thermal
degradation could be enough.
4.3.1. “High water separability” - for minimum ambient temperature min Tamb ≥ 0°C
4.3.2. “ H i g h w a t e r s e p a r a b i l i t y ” a n d “A n t i - w e a r ” c a t e g o r y - f o r m i n i m u m a m b i e n t t e m p e r a t u r e
≥ 0°C and in case of a load gear presence
4.4. Mineral or Synthetic Hydrocarbon oils ISO VG 46 High resistance to thermal degradation:
mineral oil according to ITN52220.03 - for steam turbines, expanders and electric motors as
drivers and relevant driven equipments (e.g. centrifugal or axial compressors and electric
generators) with or without load gears when low pour point characteristics are needed. This
viscosity grade category could be used also when the driver is a gas turbine and the ambient
temperature is so high that it is no possible to maintain the lube oil header at 55°C with an air
cooling system. Before taking a decision it could be necessary to perform a rotordynamic
assessment for the gas
4.4.1. “ H i g h w a t e r s e p a r a b i l i t y ” a n d “L o w P o u r P o i n t ” ( L P P ) c a t e g o r y – f o r m i n i m u m
ambient temperature -20°C ≤ min Tamb < 0°C
4.4.2. “ H i g h w a t e r s e p a r a b i l i t y ”, “L o w P o u r P o i n t ” ( L P P ) a n d “a n t i - w e a r ” c a t e g o r y - f o r
minimum ambient temperature -20°C ≤ min Tamb < 0°C and in case of a load gear
presence
4.5. Synthetic Hydrocarbon oils Group IV (PAO) ISO VG 32 and ISO VG 46 according to
ITN52220.03.
T h i s k i n d o f o i l s h a l l b e s e l e c t e d w h e n m i n i m u m a m b i e n t t e m p e r a t u r e i s b e l o w -2 0 ° C d u e t o
the fact that the pour point is below -50°C. As an example PAO oils show also a very low
tendency to form varnish. This oil is suitable to gas and steam turbines, electric motors,
electric generators, axial or centrifugal compressor and load gears. ISO VG 46 shall be used
in case the driver is a steam turbine. For a detailed description of PAO oils refer to par. XIV of
ITN52220.03.
4.5.1. ISO VG 32
4.5.2. I S O V G 3 2 w i t h “H i g h w a t e r s e p a r a b i l i t y ”
4.5.3. I S O V G 4 6 w i t h “H i g h w a t e r s e p a r a b i l i t y ”
4.6. S y n t h e t i c o i l s 5 c S t a c c o r d i n g t o M I L -L - 2 3 6 9 9 o r S A E A S 5 7 8 0 – r e c o m m e n d e d c a t e g o r y o f
synthetic oils to lubricate gas generators and aeroderivative gas turbines.
4.6.1. M I L - L -2 3 6 9 9 C l a s s S T D ( S t a n d a r d ) / S A E A S 5 7 8 0 S P C ( S t a n d a r d P e r f o r m a n c e
Capability) – the preferred choice. STD/SPC oils widely used in GE Aeroderivative
P r o d u c t s w i t h g e n e r a l c u s t o m e r s a t i s f a c t i o n a r e l i s t e d i n M I D -T D - 0 0 0 6 .
4.6.2. MIL-L-23699 Class HTS (High Thermal Stability) / SAE AS5780 HPC (High Performance
Capability) – these oils are designed to resist degradation over extended periods at higher
temperature. HTS/HPC oils widely used in GE Aeroderivative Products with general
customer satisfaction are listed in MID-TD-0006.
REVISION DESCRIPTION: MODIF PARAG 4.5 DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 4 of 12
NOTE: Service experiences with some HTS/HPC oils in GE Aviation Products have
demonstrated excessive swelling and softening of traditional AMS-R-83248 (FKM)
elastomers seals used in the lube systems. HTS/HPC oils being considered for use in
GE Aeroderivative products must be reviewed by the operator and oil supplier for
compatibility with these materials in the particular engine type, environment, and
type of service for which usage is being considered.
4.7. S y n t h e t i c o i l s 3 c S t a c c o r d i n g t o M I L -L - 7 8 0 8 – t h e y a r e n o t r e c o m m e n d e d f o r f u t u r e
applications; they can be used only for refilling in existing applications.
5. SELECTION GUIDELINES
Oil types recommended in tables A, B, C, D, E, F, G, H are for new units and new plants. For new
units in existing plants oil type shall be agreed with the customer taking into account oil
performances in the existing units.
REVISION DESCRIPTION: NO REVISION INCLUDED IN THIS SHEET DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 5 of 12
TABLE D TABLE C
ISO VG 32
YES
NO
YES
ISO VG 46
COMBINED
CYCLE WITH NO IS A LOAD
NO GEAR
STEAM TURBINE ? TABLE E
PRESENT?
YES YES
TABLE F
IS A LOAD IS A LOAD
GEAR NO NO
GEAR TABLE B
PRESENT? PRESENT?
YES
YES
TABLE G
TABLE A
TABLE H
(*) Sometimes for expanders ISO VG 68 is used
REVISION DESCRIPTION: NO REVISION INCLUDED IN THIS SHEET DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 6 of 12
Table A:
TABLE A - Gas turbine driver, no combined cycle with a steam turbine, with load gear
VISCOSITY GRADE PURCHASING
GAS TURBINE MODELS AMBIENT TEMP. REFERENCE SPECIFICATION
AND OIL TYPE (**) CODE (*)
Low varnishing oil
MS3002 Mineral or Synthetic ITN52220.03 Paragraph 15
MS5001, MS5002 C/D/E Min Tamb ≥ 0°C MCO001216
Hydrocarbon Table 1 Column 1 Section 1, 2
MS6001B, GE10-1, ISO VG 32
GE10-2
Low varnishing oil
(models with servo-
Mineral or Synthetic ITN52220.03 Paragraph 15
valves actuated by high -20°C ≤ Min Tamb < 0°C Hydrocarbon Table 1 Column 1 Section 1, 2, 3
MCO001217
pressure oil)
MS 7001 ISO VG 32
MS6001FA Low varnishing
MS9001 ITN52220.03 Paragraphs 14&15
Min Tamb < -20°C synthetic oil MCO001222
Table 3 Column 1 Section 1
(PAO) ISO VG 32
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001205
Table 1 Column 1 Section 1, 2
PGT5
HSPT for PGT25 family
ITN52220.03
GE10-1, MS5002E -20°C ≤ Min Tamb < 0°C Mineral ISO VG 32
Table 1 Column 1 Section 1, 2, 3
MCO001209
(models with electric
servo-valves)
Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001222
Table 3 Column 1 Section 1
(PAO) ISO VG 32
ITN52220.03
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001019
Table 1 Column 1 Section 1, 2
PGT16
PGT10
ITN52220.03
GE10-2 (with electric -20°C ≤ Min Tamb < 0°C Mineral ISO VG 32
Table 1 Column 1 Section 1, 2, 3
MCO001209
servo valves), GE5-1,
GE5-2
Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001222
Table 3 Column 1 Section 1
(PAO) ISO VG 32
REVISION DESCRIPTION: MODIF TABLE A - REFERENCE SPECIFICATION DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 7 of 12
Table B:
TABLE B - Gas turbine driver, no combined cycle with a steam turbine, without load gear
VISCOSITY GRADE PURCHASING
GAS TURBINE MODELS AMBIENT TEMP. REFERENCE SPECIFICATION
AND OIL TYPE (**) CODE (*)
Low varnishing oil
Mineral or Synthetic ITN52220.03 Paragraph 15
Min Tamb ≥ 0°C MCO001214
MS3002 Hydrocarbon Table 1 Column 1 Section 1
MS5001, MS5002 C/D/E ISO VG 32
MS6001B, GE10-1, GE10-2 Low varnishing oil
(models with servo-valves actuated Mineral or Synthetic ITN52220.03 Paragraph 15
by high pressure oil) -20°C ≤ Min Tamb < 0°C Hydrocarbon Table 1 Column 1 Section 1, 3
MCO001215
MS 7001 ISO VG 32
MS9001 Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001222
Table 3 Column 1 Section 1
(PAO) ISO VG 32
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001017
Table 1 Column 1 Section 1
PGT5
HSPT for PGT25 family ITN52220.03
-20°C ≤ Min Tamb < 0°C Mineral ISO VG 32
Table 1 Column 1 Section 1, 3
MCO001208
GE10-1, MS5002E
(models with electric servo-valves) Low varnishing
ITN52220.03 Paragraph 14&15 MCO001222
Min Tamb < -20°C synthetic oil
Table 3 Column 1 Section 1
(PAO) ISO VG 32
ITN52220.03
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001018
Table 1 Column 1 Section 1
PGT16
PGT10 ITN52220.03
-20°C ≤ Min Tamb < 0°C Mineral ISO VG 32
Table 1 Column 1 Section 1, 3
MCO001208
GE10-2 (with electric servo valves),
GE5-1, GE5-2 Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001222
Table 3 Column 1 Section 1
(PAO) ISO VG 32
Low varnishing oil
Mineral or Synthetic ITN52220.03 Paragraph 15
Min Tamb ≥ 0°C MCO001216
Hydrocarbon Table 1 Column 1 Section 1, 2
ISO VG 32
Low varnishing oil
MS6001FA Mineral or Synthetic ITN52220.03 Paragraph 15
-20°C ≤ Min Tamb < 0°C Hydrocarbon Table 1 Column 1 Section 1, 2, 3
MCO001217
ISO VG 32
Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001222
Table 3 Column 1 Section 1
(PAO) ISO VG 32
(**) viscosity grade ISO VG 46 could be in some cases acceptable; before taking a decision a rotor-
dynamic assessment on the gas turbine has to be performed
REVISION DESCRIPTION: MODIF TABLE B - REFERENCE SPECIFICATION DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 8 of 12
TABLE C
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001206
Table 1 Column 1 Section 1, 3
ITN52220.03
-20°C ≤ Min Tamb < 0°C Mineral ISO VG 32
Table 1 Column 1 Section 1, 3, 4
MCO001211
TABLE D
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001207
Table 1 Column 1 Section 1, 2, 3
ITN52220.03
-20°C ≤ Min Tamb < 0°C Mineral ISO VG 32
Table 1 Column 1 Section 1,2, 3, 4
MCO001213
TABLE E
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 46 MCO001226
Table 1 Column 2 Section 1, 3
ITN52220.03
-20°C ≤ Min Tamb < 0°C Mineral ISO VG 46
Table 1 Column 2 Section 1, 3, 4
MCO001228
TABLE F
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 46 MCO001227
Table 1 Column 2 Section 1, 2, 3
ITN52220.03
-20°C ≤ Min Tamb < 0°C Mineral ISO VG 46
Table 1 Column 2 Section 1,2, 3, 4
MCO001229
REVISION DESCRIPTION: MODIF ALL TABLE - REFERENCE SPECIFICATION DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 9 of 12
TABLE G
TABLE G - Gas turbine driver, combined cycle with a steam turbine, with load gear
VISCOSITY GRADE PURCHASING CODE
GAS TURBINE MODELS AMBIENT TEMP. REFERENCE SPECIFICATION
AND OIL TYPE (**) (*)
Low varnishing oil
MS3002 Mineral or Synthetic ITN52220.03 Paragraph 15
Min Tamb ≥ 0°C MCO001220
MS5001, MS5002 C/D/E Hydrocarbon Table 1 Column 1 Section 1, 2, 4
MS6001B, GE10-1, GE10-2 ISO VG 32
(models with servo-valves Low varnishing oil
actuated by high pressure Mineral or Synthetic ITN52220.03 Paragraph15
oil) -20°C ≤ Min Tamb < 0°C MCO001221
Hydrocarbon Table 1 Column 1 Section 1, 2, 3, 4
MS 7001 ISO VG 32
MS6001FA
MS9001 Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001223
Table 3 Column 1 Section 1, 2
(PAO) ISO VG 32
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001207
Table 1 Column 1 Section 1, 2, 3
PGT5
HSPT for PGT25 family
ITN52220.03
GE10-1, MS5002E -20°C ≤ Min Tamb < 0°C Mineral ISO VG 32 MCO001213
Table 1 Column Section 1, 2, 3, 4
(models with electric
servo-valves)
Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001223
Table 3 Column 1 Section 1, 2
(PAO) ISO VG 32
ITN52220.03
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001212
Table 1 Column 1 Section 1, 2, 4
PGT16
PGT10
ITN52220.03
GE10-2 (with electric -20°C ≤ Min Tamb < 0°C Mineral ISO VG 32 MCO001213
Table 1 Column 1 Section 1, 2, 3, 4
servo valves), GE5-1,
GE5-2
Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001223
Table 3 Column 1 Section 1, 2
(PAO) ISO VG 32
(**) viscosity grade ISO VG 46 could be in some cases acceptable; before taking a decision a rotor-
dynamic assessment on the gas turbine has to be performed
REVISION DESCRIPTION: MODIF ALL TABLE - REFERENCE SPECIFICATION DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 10 of 12
TABLE H
TABLE H Gas turbine driver, combined cycle with a steam turbine, without load gear
VISCOSITY GRADE PURCHASING
GAS TURBINE MODELS AMBIENT TEMP. REFERENCE SPECIFICATION
AND OIL TYPE (**) CODE (*)
Low varnishing oil
MS3002 Mineral or Synthetic ITN52220.03 Paragraph 15
MS5001, MS5002 C/D/E Min Tamb ≥ 0°C MCO001218
Hydrocarbon Table 1 Column 1 Section 1, 4
MS6001B, GE10-1, ISO VG 32
GE10-2
(models with servo- Low varnishing oil
valves actuated by high Mineral or Synthetic ITN52220.03 Paragraph 15
-20°C ≤ Min Tamb < 0°C MCO001219
pressure oil) Hydrocarbon Table 1 Column 1 Section 1, 3, 4
MS 7001 ISO VG 32
MS9001 Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001223
Table 3 Column 1 Section 1, 2
(PAO) ISO VG 32
ITN52220.02
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001206
PGT5 Table 1 Column 1 Section 1, 3
HSPT for PGT25 family ITN52220.03
GE10-1, MS5002E -20°C ≤ Min Tamb < 0°C Mineral ISO VG 32 MCO001211
Table 1 Column 1 Section 1, 3, 4
(models with electric
servo-valves) Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001223
Table 3 Column 1 Section 1, 2
(PAO) ISO VG 32
ITN52220.03
Min Tamb ≥ 0°C Mineral ISO VG 32 MCO001210
PGT16 Table 1 Column 1 Section 1, 4
PGT10 ITN52220.03
GE10-2 (with electric -20°C ≤ Min Tamb < 0°C Mineral ISO VG 32 MCO001211
Table 1 Column 1 Section 1, 3, 4
servo valves), GE5-1,
GE5-2 Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001223
Table 3 Column 1 Section 1, 2
(PAO) ISO VG 32
Low varnishing oil
Mineral or Synthetic ITN52220.03 Paragraph 15
Min Tamb ≥ 0°C MCO001220
Hydrocarbon Table 1 Column 1 Section 1, 2, 4
ISO VG 32
Low varnishing oil
MS6001FA
Mineral or Synthetic ITN52220.03 Paragraph 16 15
-20°C ≤ Min Tamb < 0°C MCO001221
Hydrocarbon Table 1 Column 1 Section 1, 2, 3, 4
ISO VG 32
Low varnishing
ITN52220.03 Paragraph 14&15
Min Tamb < -20°C synthetic oil MCO001223
Table 3 Column 1 Section 1, 2
(PAO) ISO VG 32
(**) viscosity grade ISO VG 46 could be in some cases acceptable; before taking a decision a rotor-
dynamic assessment on the gas turbine has to be performed
REVISION DESCRIPTION: MODIF ALL TABLE - REFERENCE SPECIFICATION DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 11 of 12
6. PURCHASING CODES
The following table contains the list of generic purchasing codes relevant to all identified lube oil
categories.
OIL TYPES ISO VG 32 (GT and GTP) ITN52220.03 HIGH RESISTANCE TO THERMAL DEGRADATION
4.2.1 Mineral oil Table 1 Column 1 Section 1 MCO001018
4.2.2 Mineral oil LPP Table 1 Column 1 Sections 1, 3 MCO001208
STD performance
Mineral or synthetic
4.5.2 Steam turbine comb. cycle synthetic oil (PAO) Table 3 Column 1 Sections 1, 2 + Par. 14&15 MCO001223
REVISION DESCRIPTION: MODIF REFERENCE PARAG FOR TABLE 1 AND 3 DOCUMENT CODE REVISION SIZE LANGUAGE
ITN52220.01 2 4 A
© 2018 Nuovo Pignone Tecnologie S.r.l., a Baker Hughes, a GE company, LLC (“BHGE”) company: the information contained in this document is company confidential and proprietary SHEET
property of BHGE or its affiliates. It is to be used only for the benefit of BHGE and may not be distributed, transmitted, reproduced, altered or used for any purpose without the
express written consent of BHGE. 12 of 12