Professional Documents
Culture Documents
MTNC021096A1
B1
ed
il fi Simplified Manual
p (NA7DM)
im
S
Panasonic
Models Chassis
CT-20G7DF-1 DP391
CT-20D12DF-1 EP391
CT-2017F-1 DP391
Important notice:
Since “-1” and non dash models have different PCB layouts and parts;
When servicing any of these models please confirm the model number
before starting service so the correct manual is used.
This supplement service manual is issued to ADD the models of the NA7DM family listed above to the simplified
service manual order No. MTNC020515A1 (CT-20D12F). Included in this supplement service manual are unique
characteristics and a complete parts list. Please file and use this simplified service manual together with the simplified
service manual order No. MTNC020515A1 (CT-20D12F) and the main service manual order No. MTNC010305C1
(CT-32D11E).
“WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.”
The service technician is required to read and follow the “safety precautions” and “important safety notice” in this main manual.
Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Foldouts notes . . . . . . . . . . . . . . . . . . . . . . . . . 14
A-Board TNP2AH048DR . . . . . . . . . . . . . . . . . 16
C-Board TNP2AA124AF. . . . . . . . . . . . . . . . . . 21
A-Board TNP2AH048DS. . . . . . . . . . . . . . . . . . 22
A & C-PCB Board . . . . . . . . . . . . . . . . . . . . . . . 28
-3-
Service notes
Note: These components are affixed with glue. Be careful not to break or damage any foil under the
component or at the pins of the ICs when removing. Usually applying heat to the component for a short time
while twisting with tweezers will break the component loose.
Leadless chip component How to replace Flat-IC
(surface mount) - Required tools -
Chip components must be replaced with identical chips • Soldering iron • De-solder braids
due to critical foil track spacing. There are no holes in
the board to mount standard transistors or diodes. • Sharpen pliers (wire • Magnifier
Some chips capacitor or resistor board solder pads cutters and long nose)
may have holes through the board, however the hole 1. Cut the pins of the defective IC with the wire cutters
diameter limits standard resistor replacement to 1/8 pliers, and remove it completely away from the
watt. Standard capacitor may also be limited for the board. If the IC is glued to the board, apply hot air
same reason. It is recommended that identical to complete the removal. CAUTION- Do not pull or
components be used. twist the pliers, may damage the soldering pads in
Chip resistor have a three digit numerical resistance the board.
code - 1st and 2nd significant digits and a multiplier.
Componente
Example: 162 = 1600 or 1.6kΩ resistor, 0 = 0Ω (jumper). plano
Chip capacitors generally do not have the value
indicated on the capacitor. The color of the component
indicates the general range of the capacitance.
Chip transistors are identified by a two letter code. The 2. Using the soldering Iron and the long nose pliers,
remove the IC pins that still attached to the board.
first letter indicates the type and the second letter, the
grade of transistor.
Chip diodes have a two letter identification code as per
the code chart and are a dual diode pack with either
common anode or common cathode. Check the parts
list for correct diode number. Cautin
Component removal 3. Using the de-solder braid and the soldering iron,
1. Use solder wick to remove solder from component remove the solder from the board soldering pads.
end caps or terminal. malla
para desoldar
2. Without pulling up, carefully twist the component
with tweezers to break the adhesive. cautin
Iron
3. Do not reuse removed leadless or chip
components since they are subject to stress
fracture during removal. 4. Position the new Flat-IC in place (apply the pins of
the Flat-IC to the soldering pads where the pins
Chip component Installation need to be soldered). Properly determine the
1. Put a small amount of solder on the board positions of the soldering pads and pins by
soldering pads. correctly aligning the polarity symbol. Start aligning
2. Hold the chip component against the soldering and soldering pin no.1, then align and solder the
pads with tweezers or with a miniature alligator clip
pin in the apposite corner of the IC, this will help to
and apply heat to the pad area with a 30 watt iron
until solder flows. Do not apply heat for more than align the rest of the pins.
3 seconds. Muesca 2do punto
1er punto
TYPE Chip components SOLDER
CAPS
GRADE
c
5. Solder all pins to the soldering pads using a fine
tipped soldering iron.
b
e
TRANSISTOR CAPACITOR
1ST DIGIT 2ND DIGIT Soldadura
COMMON Cautin con
CATHODE punta fina
MULTIPLIER
=1600 = 1.6k 6. Check with a magnifier for solder bridge between
the pins or for dry joint between pins and soldering
ANODES SOLDER pads. To remove a solder bridge, use a de-solder
CAPS
RESISTOR
braid as shown in the figure below.
MH DIODE
Malla
Puente
(en corto)
Cautin
-4-
Service notes (continued)
IMPORTANT: To protect against possible damage to Procedure:
the solid state devices due to arcing or static discharge, 1. Connect receiver to isolator transformer.
make certain that all ground wires and CTR DAG wire 2. Apply a monoscope pattern.
are securely connected. 3. In service mode. (Refer to service mode section)
CAUTION: The power supply circuit is above earth select register C0B.
ground and the chassis cannot be polarized. Use an 4. Measure TP5 (TPs port close to tuner). Compare
isolation transformer when servicing the receiver to the measure of TP5 and set the data for C0B
avoid damage to the test equipment or to the chassis. according the following table
Connect the test equipment to the proper ground ( ) or
( ) when servicing, or incorrect voltages will be TP5 DATA TO
measured. MEASURE (V) C0B (Hex)
-5-
Receiver feature table
FEATURE\MODEL CT-20G7DF-1 CT-20D12DF-1 CT-2017F-1
-6-
Boards designation
MODELS BOARD PART NUMBER BOARD DESCRIPTION
Boards designation
MODELS BOARD PART NUMBER BOARD DESCRIPTION
Important notice:
Since “-1” and non dash models have different PCB layouts and parts;
When servicing any of these models please confirm the model number
before starting service so the correct manual is used.
-7-
REPLACEMENT PARTS LIST
Models: CT-20G7DF-1, CT-20D12DF-1, CT-2017F-1
Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing
any of these components use only manufacturer’s specified parts.
REF REF
PART NO. DESCRIPTION PART NO. DESCRIPTION
NO. NO.
C054 TCJ2VB1H103K
CT-20D12DF-1 C575 ECA0JM222B CAP,E 2200UF-6.3V
C055 TCJ2VC1H560J CAP,C 56PF-J-50V C577 ECA1CM101B CAP,E 100UF/16V
CAP,C 470PF-J-50V C578 ECA0JM332B CAP,E 3300PF-6.3V
C057 TCJ2VC1H471J
CT-20D12DF-1 C579 TCJ2VC1H100D CAP,C 10PF-J-50V
C103 ECA0JM331B CAP,E 330UF-6.3V
C580 TCJ2VB1H152K CAP,C 1500PF-K-50V
C104 TCJ2VB1H103K CAP,C .01UF-K-50V C605 TCJ2VB1H103K CAP,C .01UF-K-50V
C105 ECA0JM101B CAP,E 100UF-6.3V C606 ECA0JM221B CAP,E 220UF-6.3V
C350 ECA1CM101B CAP,E 100UF/16V
- 11 - Parts List
302-02
REPLACEMENT PARTS LIST
Models: CT-20G7DF-1, CT-20D12DF-1, CT-2017F-1
Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing
any of these components use only manufacturer’s specified parts.
REF REF
PART NO. DESCRIPTION PART NO. DESCRIPTION
NO. NO.
R470 ERDS2TJ152T RES,C 1.5K-J-1/4W R824 ERDS2TJ223T RES,C 22K-J-1/4W
R471 ERJ6GEYJ223V RES,M 22K-J-1/10W R825 ERDS2TJ272T RES,C 2.7K-J-1/4W
R472 ERJ6GEYJ473V RES,M 47K-J-1/10W R828 ERJ6GEYJ104V RES,M 100K-J-1/10W
R475 ERJ6GEYJ471V RES,M 470-J-1/10W R830 ERDS2TJ104T RES,C 100K-J-1/4W
R502 ERJ6GEYJ562V RES,M 5.6K-J-1/10W R831 ERDS2TJ682T RES,C 6.8K-J-1/4W
R504 ERDS2TJ272T RES,C 2.7K-J-1/4W R850 ERQ12HJR56P RES,F .56-J-1/2W
R505 ERJ6GEYJ222V RES,M 2.2K-J-1/10W R2201 ERJ6GEYJ224V RES,M 220K-J-1/10W
R506 ERJ6GEYJ333V RES,M 33K-J-1/10W R2203 ERJ6GEYJ102V RES,M 1K-J-1/10W
R507 ERJ6GEYJ103V RES,M 10K-J-1/10W R2204 ERJ6GEYJ102V RES,M 1K-J-1/10W
R508 ERJ6GEYJ103V RES,M 10K-J-1/10W R2205 ERJ6GEYJ101V RES,M 100-J-1/10W
R510 ERG3FJ272 RES,M 2.7K-J-3W R2206 ERJ6GEYJ273V RES,M 27K-J-1/10W
R512 ERG2FJ562H RES,M 5.6K-J-2W R2301 ERQ2CJP3R9S RES,F 3.9-J-2W
R520 ERJ6GEYJ471V RES,M 470-J-1/10W R2307 ERJ6GEYJ103V RES,M 10K-J-1/10W
R521 ERJ6GEYJ272V RES,M 2.7K-J-1/10W RES,M 100K-J-1/10W
R2320 ERJ6GEYJ104V
R531 ERD25FJ470P RES,C 47-J-1/4W CT-20D12DF-1
R532 ERJ6ENF8871V RES,M 8.87K-F-1/10W R2350 ERDS2TJ391T RES,C 390-J-1/4W
RESISTOR CAPACITOR
TYPE TOLERANCE TYPE TOLERANCE
C Carbon F ± 1% C Ceramic C ± 0.25pF
F Fuse J ± 5% E Electrolytic D ± 0.5pF
M Metal Oxide K ± 10% P Polyester F ± 1pF
S Solid M ± 20% S Styrol J ± 5%
W Wire Wound G ± 2% T Tantalum K ± 10%
L ± 15%
RES, C 270-J-1/4
M ± 20%
PARTS LIST
P +10% -0%
Z +80% -20%
CAP, P .068UF-K-50V
- 13 - Parts List
302-02
Notes
IMPORTANT SAFETY NOTICE
CHIP TRANSISTOR
THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL
LEAD DESIGNATION
FEATURES THAT ARE IMPORTANT FOR PROTECTION FROM
X-RADIATION, FIRE AND ELECTRICAL SHOCK HAZARDS.
WHEN SERVICING IT IS ESSENTIAL THAT ONLY
B
C
MANUFACTURERS SPECIFIED PARTS BE USED FOR THE E
CRITICAL COMPONENTS DESIGNATED WITH A IN THE
SCHEMATIC.
SCHEMATIC NOTES
1. Resistors are carbon 1/4W unless noted 6. (BOLD LINE) indicates the route
otherwise. of B+ supply.
2. Capacitors are ceramic 50V unless noted 7. The schematic diagrams are current at
otherwise. the time of printing and are subject to
3. Coil value notes is inductance in µH. change without notice.
4. Test point indicated by ; Test point but no 8. Ground symbol indicates HOT
pin . GROUND CONNECTION;
5. Components indicated with are critical indicates COLD GROUND.
parts and replacement should be made NOTE: All other component symbols are
with manufacture specified replacement used for engineering design
parts only. purposes.
VOLTAGE MEASUREMENTS
1. Voltage measurement: - Voltage readings are nominal and
- AC input to the Receiver is 120V. may vary ±10% on active devices.
NTSC (HD, 1125i & 525P when Some voltage reading will vary
applicable) signal generator is with signal strength and picture
connected to the antenna of the content.
Receiver. (Color bar pattern of 100 - Supply voltages are nominal.
IRE white and 7.5 IRE black.) 2. Ground symbol indicates ground lead
- All Picture and Audio adjustments are connection of meter.
set to Normalize. Incorrect ground connection will result
TV ANT/CABLE - (Set-Up Menu) in in erroneous readings.
TV/ANT Mode CAUTION: Incorrect ground connection
Volume - Min. of the test equipment will result in
TV/Video SW - TV position erroneous readings.
Audio Mode - Stereo
3 WAVEFORM MEASUREMENTS
1. indicates waveform measurement. 4. All video and color waveforms are taken
(Measurement can be taken at the best with a wideband scope and a probe
accessible location in common to the with low capacitance (10 to 1). Shape
indicated point.) and peak altitudes may vary
2. Taken with an NTSC signal generator depending on the type of Oscilloscope
connected to the antenna terminal. used and its settings.
(NTSC color bar pattern of 8 bars of EIA 5. Ground symbol shown on waveform
colors, 100 IRE white and 7.5 IRE black.) number indicates (Hot) ground lead
3. Customer Controls (Picture/Audio Menu) are connection of the Oscilloscope.
set to Normalize. Volume is set to “MIN”. CAUTION: Incorrect ground connection of
the test equipment will result in erroneous
readings.
- 14 -
Notas:
NOTA DE SEGURIDAD
LOS DIAGRAMAS ELÉCTRICOS INCLUYEN
CARACTERÍSTICAS ESPECIALES MUY IMPORTANTES IDENTIFICACIÓN DE TERMINALES
PARA LA PROTECCIÓN CONTRA RAYOS-X, PARA TRANSISTORES EN CHIP
QUEMADURAS Y DESCARGAS ELÉCTRICAS. CUANDO
SE DE SERVICIO ES IMPORTANTE USAR PARA B
REEMPLAZO DE COMPONENTES CRITICOS, SOLO C
E
PARTES ESPECIFICADAS POR EL FABRICANTES. LOS
COMPONENTES CRITICOS ESTAN SEÑALADOS EN LOS
DIAGRAMAS POR EL SIMBOLO .
MEDICIÓN DE VOLTAJES
1. Medición de voltaje: - Las mediciones de los voltajes son
- El voltaje de entrada al Receptor es de nominales y pueden variar hasta
120V de Corriente Alterna. Un 10% en componentes en
generador de patrones con formato funcionamiento. Las lecturas de los
NTSC se conecta a la entrada de la voltajes pueden variar por la
antena. (Patrón de Barras de Colores potencia de la señal y el contenido
con 100 IREs para el Blanco y 7.5 IREs de la imagen.
para el Negro.) - Las fuentes de voltajes son
- Los ajustes de los Menus Picture y nominales.
Audio se normalizan. 2. El símbolo indica el tipo de tierra que
En el Menú Set-Up, en la opción se utiliza en la conexión del medidor.
ANTENA, se selecciona el modo de
CABLE. PRECAUCION: SI no se utiliza la
El nivel de Volumen se minimiza. conexión a la tierra adecuada, se
De los modos TV y Video, seleccionar el obtendrán mediciones equivocadas y
modo TV. podría dañar el equipo de medición.
Seleccionar modo Estereo del Audio.
- 15 -
TNP2AH048DR - 16 - CT-2017F-1, CT-20G7DF-1
CT-2017F-1, CT-20G7DF-1 - 17 - TNP2AH048DR
TNP2AH048DR - 18 - CT-2017F-1, CT-20G7DF-1
CT-2017F-1, CT-20G7DF-1 - 19 - TNP2AH048DR
TNP2AH048DR - 20 - CT-2017F-1, CT-20G7DF-1
CT-2017F-1, CT-20G7DF-1, CT-20D12DF-1 - 21 - TNP2AA124AF
TNP2AH048DS - 22 - CT-20D12DF-1
CT-20D12DF-1 - 23 - TNP2AH048DS
TNP2AH048DS - 24 - CT-20D12DF-1
CT-20D12DF-1 - 25 - TNP2AH048DS
TNP2AH048DS - 26 - CT-20D12DF-1
NOTES:
- 27 - NOTES
A & C PCB BOARD - 28 - ALL MODELS
ALL MODELS - 29 - A & C PCB BOARD
Printed in USA
K02102597PL1113