Professional Documents
Culture Documents
In India A Coal
In India A Coal
_______ m.
Options:
(1) 2.8
(2) 3
(3) 3.6
(4) 4.5
(5) 4.8
Question Text:
If a shaft is more than ___________ m in depth, arrangements shall be by mechanical means for persons
to descend and ascend.
Options:
(1) 20
(2) 25
(3) 30
(4) 40
(5) 50
Question Text:
RMR is predominantly used for estimation of rock load and design of the support system for
Options:
www.onlineminingexam.com
Question Text:
In favorable geomining condition, for high production and high productivity mechanised mining of flat to
gently dipping, 1.5 to 4.5 m thick coal seams, the most suitable method is __________
Options:
www.onlineminingexam.com
Options:
(1) rigid
(2) yielding
(3) tangential
(4) diagonal
(5) flat
www.onlineminingexam.com
Question Text:
The type of permitted explosive used for off-the-solid blasting in coal mines is ____.
Options:
(1) P1
(2) P2
(3) P3
(4) P4
(5) P5
Question Text:
Options:
(1) Marginal
(2) Sub-critical
(3) Critical
(4) Super-critical
(5) Nominal
Question Text:
The subsidence that continues to occur after the completion of depillaring is known as
___________ subsidence.
Options:
(1) critical
(2) nominal
(3) sub-critical
(4) residual
(5) critical
Question Text:
Proneness to spontaneous heating is high in the following crossing point temperature range-
Options:
Question Text:
(1) Gradient
(2) Throw
(3) Hade
(4) Upthrow
(5) Downthrow
Question Text:
Options:
www.onlineminingexam.com
Question Text:
Options:
www.onlineminingexam.com
Question Text:
In case of a weak rock overlain by strong rock the rock bolt installed through them will act in
_________.
Options:
(1) Suspension
(3) Keying
(4) Consolidation
www.onlineminingexam.com
Options:
(1) 1.5 m
(2) 2.5 m
(3) 3.5 m
(4) 4.5 m
(5) 5.5 m
Question Text:
Options:
(1) Areas having frequent geological disturbances are not suitable for Mechanised bord and pillar
mining
(2) Blasting Gallery method is suitable ideally for gassy seams of degree III
(3) Mechanised board and pillar mining is not suitable for seams having inclination less than 15°
(4) Mechanised longwall mining is not suitable for seams having inclination less than 15°
(5) Areas having frequent geological disturbances are suitable for mechanised bord and pillar mining
www.onlineminingexam.com
Question Text:
Every plan and section prepared in accordance with the provisions of CMR, 1957 shall show a scale of
the plan at least __________.
Options:
www.onlineminingexam.com
Question Text:
Options:
www.onlineminingexam.com
Question Text:
Options:
www.onlineminingexam.com
Question Text:
NONEL helps in reducing________.
Options:
www.onlineminingexam.com
Question Text:
Options:
(1) Pay back period
(4) Depreciation
www.onlineminingexam.com
Question Text:
Which of the following factor is considered for calculation of cycle time of excavating machine?
Options:
www.onlineminingexam.com
Question Text:
In an opencast coal mine, bench failure has occurred in which a triangular portion has come out. The
type of failure is_________________.
Options:
(3) Toppling up
www.onlineminingexam.com
Question Text:
Options:
www.onlineminingexam.com
Question Text:
Options:
www.onlineminingexam.com
Question Text:
(1) Angle between limit line of subsidence & vertical line on any side
Question Text:
Bord and pillar workings in two flat or gently dipping contiguous seams should be developed with their
roadways and pillars perfectly ___________.
Options:
(1) Diagonal
(2) Overlapping
(5) Pyramidal
www.onlineminingexam.com
Question Text:
Piling Method, Cassion Method, Freezing Method, Cementation Process are some splecial methods of
_____________ for loose, unstable ground with or without presence of water
Options:
(2) Drifting
www.onlineminingexam.com
Question Text:
The workings of two underground mines each having 4.8 m gallery width at 100 depth must be
separated by a minimum distance of ________ m .
Options:
(1) 16.5 m
(2) 19.5 m
(3) 22.5 m
(4) 25.5 m
(5) 30.5 m
Question Text:
(5) convergence
www.onlineminingexam.com
Question Text:
Options:
(1) in detonators
(2) as additive to sensitize explosives
Question Text:
Options:
Question Text:
www.onlineminingexam.com
Options:
www.onlineminingexam.com
Question Text:
Options:
(1) mm/s
(2) Pascal
(3) dB
(4) Nm
(5) m/min
www.onlineminingexam.com
Question Text:
______________ is the smallest absolute value of a parameter that can be measured by a monitoring
instrument.
Options:
(1) Sensitivity
(3) Accuracy
(4) Reliability
(5) Repeatability
www.onlineminingexam.com
Question Text:
Factor of safety of slope of an opencast mine _____________ with increase in pore water pressure.
Options:
(1) goes up
(2) reduces
(3) remains unchanged
(4) fluctuates
www.onlineminingexam.com
Question Text:
Safe limit of tensile strain in forest land is ___ mm/m as per the guidelines of the Ministry of
Environment & Forests.
Options:
(1) 3
(2) 7
(3) 12
(4) 16
(5) 20
Correction Answer : Option No.(5)
www.onlineminingexam.com
Question Text:
Pick the odd one out which is not contributing to coalification process.
Options:
(2) Time
Question Text:
VOD is a term related to______________.
Options:
(2) explosive
(3) exploder
Question Text:
Options:
(1) PETN
(2) ASA
(3) TNT
(5) Fuse
Question Text:
Options:
www.onlineminingexam.com
Question Text:
Options:
www.onlineminingexam.com
Question Text:
Which is not true in case of a shock tube initiating system, such as NONEL?
Options:
www.onlineminingexam.com
Question Text:
The location of primary openings like shafts/ inclines can be best selected in multi-seam development by
considering the _________________.
Options:
(1) Total ton-km effort
www.onlineminingexam.com
Question Text:
Options:
(1) σt = P / (πDt)
www.onlineminingexam.com
Question Text:
Options:
Question Text:
Which of the following statements is wrong in the case of blast design for opencast mines?
Options:
Question Text:
Pressure arch theory deals with _________.
Options:
Question Text:
Options:
(1) 8 to 12 m
(2) 1 to 3 m
(3) 2.5 to 4.8 m
(4) 3 to 7 m
Question Text:
Minimum thickness of parting to be left between two sections of a thick seam is _________.
Options:
(1) 3 m
(2) 5 m
(3) 7 m
(4) 1 m
(5) 5.5 m
Correction Answer : Option No.(1)
Question Text:
Options:
www.onlineminingexam.com
Question Text:
While working in an OCP over the developed workings, the parting above the gallery is proved by
_________.
Options:
(4) Pre-splitting
Question Text:
In longwall mining advance supporting of gate roads upto 30 m from the face is required due
to________.
Options:
Question Text:
An overhead line is passing over a haul road. What should be the minimum clearance of lowest
conductor over haul road?
Options:
(1) At least 15 m
(2) At least 10 m
(3) At least 12 m
(4) At least 5 m
(5) At least 8 m
Correction Answer : Option No.(3)
Question Text:
Options:
(1) P wave
(2) S wave
www.onlineminingexam.com
Question Text:
What is the maximum height or width of advanced heading for dewatering of water-logged workings in
coal mines ?
Options:
(1) 2.0 m
(2) 2.4 m
(3) 2.8 m
(4) 3.0 m
(5) 3.4 m
Question Text:
Every shaft, incline and other outlets provided in an underground coal mine shall be examined, once at
least in every _____________, by an ___________ or other competent person and a report of every
such examination shall immediately thereafter be recorded in a bound paged book kept for the purpose
and shall be signed and dated by the person making the examination.
Options:
Question Text:
Options:
(1) 10
(2) 11
(3) 12
(4) 13
(5) 14
Question Text:
Options:
(3) Maximum tensile stress shifts from the edge to centre of the goaf
(4) Maximum tensile stress shall be away from the chain pillars
www.onlineminingexam.com
Question Text:
Stress is a ______________ quantity.
Options:
(1) Scalar
(2) Vector
(3) Tensor
(4) Imaginary
(5) Exponential
Question Text:
In a subsidence profile, the point at which the curvature changes from positive to negative is known as
__________.
Options:
Question Text:
For smooth flow, the velocity of sand-water slurry in stowing pipeline should be __________ than the
_________ velocity of deposition.
Options:
(1) more;optimum
(2) less;optimum
(3) more;critical
(4) less;marginal
(5) more;marginal
Correction Answer : Option No.(3)
Question Text:
Among Wide & Stall, Knife Edge, Bhaska and Tipong ______________ are underground coal mining
methods.
Options:
Question Text:
www.onlineminingexam.com
(2) circle
(3) semi-circle
(4) arch
(5) pyramid
Question Text:
Options:
Question Text:
What is the prescribed minimum depth of locking of Brick Isolation Stoppings into coal, shale and
sandstone?
Options:
Question Text:
If R is RMR, S is gallery span in metre, D is mean rock density in tonne/m3, then what will be the
Empirical Formula for Rock Load in tonne/m3 ?
Options:
(1) SxD(1.7-0.0037R+0.002R2)
(2) SxD(1.77-0.37R+0.0002R2)
(3) SxD(2.7-0.037R+0.002R2)
(4) SxD(1.7-0.037R+0.0002R2)
(5) SxD(1.7-0.0037R+0.02R2)
Question Text:
Which of the following statement pertaining to the "Angle of Draw" of an inclined coal seam is true ?
Options:
www.onlineminingexam.com
Question Text:
Options:
(1) strength
(2) thickness
(3) RQD
Question Text:
Options:
Question Text:
The rock sample having 5.4 cm diameter and 2.7 cm thickness failed at a compressive load of 2403.45 kg
while carrying out Brazilian test. Tensile strength of the test rock sample will be
___________.
Options:
Question Text:
Options:
Question Text:
1. The drilling efficiency of DTH blasthole drills is not affected significantly with the increase of
www.onlineminingexam.com
drilling depth. 2. The rotary blast hole drillss are more efficient compared to percussive blasthole drills
for all types of rock formation. 3. Rotary blast hole drillss are more efficient compared to percussive
blasthole drills for all types of rock formation. 3. Rotary percussive drills are suited for hard and non-
abrasive rocks.
Options:
Question Text:
In case of full height development of a coal seam, formation of square pillar of 42 m x 42 m (centre to
centre) with 3.6 m wide gallery will cause________.
Options:
Question Text:
A 10 mm thick sample prepared from a 54 mm dia core was tested for tensile strength (Brazilian). The
breaking load was 0.5 tonne. Considering the value of π to be equal to 3.14, the tensile strength of the
sample will be nearly equal to_________.
Options:
(1) 50 kg/cm2
(2) 60 kg/cm2
(3) 70 kg/cm2
(4) 80 kg/cm2
(5) 90 kg/cm2
Question Text:
A surface coal mine is worked by 10 m3 shovel – 85 tonne dumper combination. If the shovel bucket fill
factor is 0.8, the material swell factor is 0.75 and the average in-situ sp.gr. of the material is 3.5
tonne/m3, the number of shovel bucket loads required to fill a dumper will be nearly_____
Options:
(1) 3
(2) 4
(3) 5
(4) 6
(5) 7
www.onlineminingexam.com
Question Text:
What would be the capacity of a flat belt conveyor in ton/ hour, if the bulk density of material is 0.8
t/m3, belt width is 1.0 m, angle of repose is 45° and velocity is 100 m/min?
Options:
(1) 1300
(2) 1200
(3) 1000
(4) 1100
(5) 900
Correction Answer : Option No.(2)
Question Text:
Options:
Question Text:
About ___% of the installed roof bolts should be tested upto the designed capacity, and rest ___% may
be subjected to destructive testing.
Options:
(1) 9; 1
(2) 5; 10
(3) 10; 5
(4) 3; 7
(5) 8; 2
Question Text:
Options:
Question Text:
Permissible Peak Particle Velocity (ppv) at the foundation level of structures in mining areas depend on
ownership of building, type of structure and _____________.
www.onlineminingexam.com
Options:
Correction Answer : O