Professional Documents
Culture Documents
Dornblüthstr. 14a
01277 Dresden
Germany
Tel.: +49 351 317 24 - 0
Fax: +49 351 310 50 85
E-Mail: info@vacutec-gmbh.de
Web: www.vacutec-gmbh.de
Application
The VacuDAP – OEM duo measuring chamber determines the radiation level a patient is exposed to in radiological
diagnostics, especially if a combination of fluoroscopic and radiographic units are used. The following values are
measured simultaneously:
Reference air kerma (RAK)
Reference air kerma rate (RAKR)
Dose area product (DAP)
Dose area product rate (DAPR)
Irradiation time (cumulative)
The VacuDAP – OEM duo meets the requirements for dosimetric indications according to IEC 60601-2-54,
IEC 60601-2-43 and 21 CFR 1020.32 and the requirements for dose area product meters according to IEC 60580.
Because of the high digital resolution the measuring system can be used for pediatric and standard methods.
At the VacuDAP duo measuring system the measuring chamber is completed by a display unit. Alternatively the
VacuDAP - OEM duo measuring chamber can be used with a host computer (i. e. PC or X-ray generator).
The measuring chamber 458 00 15 consists of a ionization chamber and the integrated electronics. By means of
interchangeable guide rails, the measuring chamber is pushed into the accessory support at the radiation outlet
end of the beam limiting device. Different adapters are available for the application of additional filters. The ioniza-
tion chamber is highly transparent and does not affect the functionality of the light beam diaphragm.
Only values given with tolerance ranges, or limits are guaranteed. All other values are for information only. Subject to change.
458DB15E
Revision B 1/6
VacuTec Meßtechnik GmbH
Dornblüthstr. 14a
01277 Dresden
Germany
Tel.: +49 351 317 24 - 0
Fax: +49 351 310 50 85
E-Mail: info@vacutec-gmbh.de
Web: www.vacutec-gmbh.de
Only values given with tolerance ranges, or limits are guaranteed. All other values are for information only. Subject to change.
458DB15E
Revision B 2/6
VacuTec Meßtechnik GmbH
Dornblüthstr. 14a
01277 Dresden
Germany
Tel.: +49 351 317 24 - 0
Fax: +49 351 310 50 85
E-Mail: info@vacutec-gmbh.de
Web: www.vacutec-gmbh.de
Only values given with tolerance ranges, or limits are guaranteed. All other values are for information only. Subject to change.
458DB15E
Revision B 3/6
VacuTec Meßtechnik GmbH
Dornblüthstr. 14a
01277 Dresden
Germany
Tel.: +49 351 317 24 - 0
Fax: +49 351 310 50 85
E-Mail: info@vacutec-gmbh.de
Web: www.vacutec-gmbh.de
Interface
Data cable with 4-pin male cable connector (ODU: MediSnap) and the following pin assignment:
Only values given with tolerance ranges, or limits are guaranteed. All other values are for information only. Subject to change.
458DB15E
Revision B 4/6
VacuTec Meßtechnik GmbH
Dornblüthstr. 14a
01277 Dresden
Germany
Tel.: +49 351 317 24 - 0
Fax: +49 351 310 50 85
E-Mail: info@vacutec-gmbh.de
Web: www.vacutec-gmbh.de
If the measuring chamber is used at altitudes above 300 m the systematic error
caused by the change of air density depending on the altitude has to be corrected.
After installation the calibration should be tested at installation conditions (see Instructions for Use). The obtained
calibration factor includes the correction for the altitude. If a calibration test at installation conditions is not possible
the correction can also be done by taking the respective correction factor k2 from Graph 2 to correct the calibration
factor.
1,2
1,0
0,8
correction factor k1
0,6
0,0
40 50 60 70 80 90 100 110 120 130 140 150
X-ray voltage U [kV]
Only values given with tolerance ranges, or limits are guaranteed. All other values are for information only. Subject to change.
458DB15E
Revision B 5/6
VacuTec Meßtechnik GmbH
Dornblüthstr. 14a
01277 Dresden
Germany
Tel.: +49 351 317 24 - 0
Fax: +49 351 310 50 85
E-Mail: info@vacutec-gmbh.de
Web: www.vacutec-gmbh.de
1,4
1,3
Correction factor k2
1,2
1,1
1,0
Only values given with tolerance ranges, or limits are guaranteed. All other values are for information only. Subject to change.
458DB15E
Revision B 6/6