Professional Documents
Culture Documents
RF roof
- Oils and fats .................................................. ............. Two Sunroof switch system inspection ........................ Sixteen
Front sunroof ............................................... Three Slide switch system inspection ........................... 17 C
And removal, installation ......................................... Three Tilt switch system inspection ............................... Eighteen
· Kenzuke inspection .................................................. ... ...... 6 Auto switch system inspection ............................... Twenty
Rear sunroof ................................................ ...... 8 And alarm buzzer system inspection ................................... . . . twenty one
System FIG. ................................................. ...... 8 Sunroof motor system inspection ........................ twenty two
D
System Overview .............................................. ...... 8 Sunroof motor circuit system inspection ................ twenty three
· Component mounting position ....................................... . . . . 11 Sunroof identification terminal circuit system inspection ................ twenty three
·circuit diagram .................................................. ........... Twelve Remote control system inspection .......................................... twenty three
Roof control unit input and output signal based on Removing roof control unit, taken
Quasi-value .................................................. .......... . . . . 12 Attach .................................................. ....... . . . twenty four E
Sunroof communication diagnosis ....................................... 14 And removal, installation ................................... . . . twenty five
- How to proceed with fault diagnosis ....................................... . . . . 15 · Kenzuke inspection .................................................. ...... 28
RF
KA
RF - 1
Prepared by
RF - 2
Front sunroof
Caution : When removing the sunroof unit and glass lid, so as not to hurt the seat, trims and the body in cloth, etc.
It is protected.
RF
KA
PIIA1593J
RF - 3
Front sunroof
Ten. Sunroof bracket (rear) 11. Sunroof unit members 12. sunshade
Sunroof unit
removal
1. Remove the head lining. " EI Exterior and interior "of "Removing, mounting" ( EI-35 page ) reference.
2. Rear display unit ASSY Remove the rear (rear display unit ASSY Car attached). " AV Audio, TV,
Navigation phone "of "Rear display unit ASSY Removal of, mounting "( AV-217 page ) reference.
PIIA1594J
6. Remove the nut, remove the sunroof unit from the roof panel.
Caution : When removing the sunroof unit, since there is a risk of falling off
PIIA1595J
attachment
1. Set the sunroof unit to the roof panel, temporarily fixed with a nut.
2. Attach the sunroof bracket, temporarily stop of the vehicle body-side bolt.
3. Tighten the nut to the specified torque on the diagonal, then tighten the body-side bolt of the sunroof bracket to the specified torque
That.
6. Rear display unit ASSY The mount. (Rear display unit ASSY Car attached). " AV audio·
TV navigation phone "of " Rear display unit ASSY Removing, mounting " (AV-217 page ) reference. -
7. Attaching the head lining. " EI Exterior and interior "of "Removing, mounting" ( EI-35 page ) reference.
RF - 4
Front sunroof
sunshade
removal
1. Remove the sunroof unit. " Sunroof unit "( RF-4 page ) reference.
PIIA1596J
attachment D
E
Glass lid
removal
1. Remove the sunroof unit. " Sunroof unit "( RF-4 page ) reference.
F
2. Remove the nuts that attach the glass lid.
3. Unlock the glass lid and remove the glass lid with.
Caution : When removing the glass lid, to work with 2 or more people.
H
PIIA1597J
attachment
1. Set the glass lid to the roof panel, to lock the glass lid.
RF
2. Tighten the nut on the diagonal to the specified torque.
3. Carry out the operation and Kenzuke inspection of the glass lid. " Kenzuke inspection "( RF-6 page ) reference.
Four. Installing a sunroof unit. " Sunroof unit "( RF-4 page ) reference.
J
KA
RF - 5
Front sunroof
Inspect the gap and surface difference between the glass lid and the roof panel, make adjustments as needed.
PIIA1598J
1. Remove the sunroof unit. " Sunroof unit "( RF-4 page ) reference.
2. Loosen the nuts that attach the glass lid. " Glass lid "( RF-5 page ) reference.
Four. Tightening on the diagonal the glass lid to the specified torque, do a few times tilt operation.
Five. Installing a sunroof unit. " Sunroof unit "( RF-4 page ) reference.
1. Remove the sunroof unit. " Sunroof unit "( RF-4 page ) reference.
3. To adjust the height of the glass lid in the increase or decrease in the number of shims.
Four. Tighten the sunroof striker to the specified torque, several times sunroof
PIIA1599J
RF - 6
Front sunroof
Kenzuke After inspection, sunroof, in each door and window fully closed state, the inspection that there is no water leakage flow of water to the entire roof do.
RF
KA
RF - 7
Rear sunroof
PIIA9720J
Sunroof switch or rear sunroof and operates the remote control switch, makes slide, tilt actuation.
Feature Description
• When operating the sunroof switch roof control unit receives a signal to actuate the sunroof motor.
• When operating the remote control switch roof control unit receives a signal to actuate the sunroof motor.
Sunroof switch signal roof control unit at the time of the sunroof operation sunroof switch One , Two , Three of ON - OFF Do fully open by the combination
of, fully closed, pause, the control such as tilt-up to the sunroof motor.
slide slide Tilt-up Tilt down Auto slide When auto slide closing IGN OFF
stop
Open Closed open Time
sunroof
about 0V about 12V about 12V about 0V about 0V about 12V about 0V about 12V
SW1
sunroof
about 0V about 0V about 0V about 12V about 12V about 12V about 0V about 12V
SW2
sunroof
about 12V about 12V about 0V about 12V about 0V about 0V about 0V about 12V
SW3
RF - 8
Rear sunroof
Control at the time of simultaneous push of the sunroof switch and a remote control switch
OFF ON
(unlock) (Locked)
Remote controller SW
down OPEN OPEN OPEN OPEN OPEN STOP note STOP note STOP
Lumpur
ATOP ATOP OPEN ATOP OPEN STOP note STOP note STOP
I
Full CLOSE CLOSE OPEN OPEN CLOSE STOP note STOP note STOP C
SW
ATCL ATCL OPEN OPEN CLOSE STOP note STOP note STOP
D
STOP : Stop (Stop)
OPEN : Opening operation (fully closed → fully open)
STOP note : When the tilt-up is pressed later by a stop output, sunroof SW1 , Two , Three The output of 20msOFF To.
F
• When you operate the sunroof switch or remote control switch in the sunroof lock state sounds a buzzer.
• When auto operation of the sunroof switch and when the remote control operation (all operations) is sounding the buzzer.
• When you stop at an intermediate stop position in the slide closed operation, sound the buzzer. G
• Key OFF Sometimes when the sunroof is other than the fully closed state, the buzzer.
DESCRIPTION OF OPERATION
H
circuit diagram
RF
KA
PIIA9721J
RF - 9
Rear sunroof
• When the sunroof switch to slide open operation, the sunroof switch slides (open) circuit is turned on roof Control Ruyunitto 34 Turn terminal is
grounded.
• 34 When the turn terminal is grounded roof control unit Twelve Stop the earth turn terminal, 13 , 14 To ground the turn terminal.
• The sunroof motor has been detected it sunroof rotates in the opening direction to slide in the opening direction.
• When the sunroof switch to slide closing operation, and the conduction of the sunroof switch slides (closed) circuit roof Control Ruyunitto 36 Turn terminal is
grounded.
• 36 When the turn terminal is grounded roof control unit Twelve , 14 Stop the earth turn terminal 13 To ground the turn terminal.
• Sunroof motor has been detected it is sunroof rotates in the closing direction to slide in the closing direction.
• When the sunroof switch tilt-up to operation, roof control unit conducts tilt-up circuit of the sunroof switch 37 Turn terminal is grounded.
• 37 When the turn terminal is grounded roof control unit 14 Stop the earth turn terminal, Twelve , 13 To ground the turn terminal.
• When the sunroof switch tilt down to manipulate, roof control unit conducts tilt-down circuit of the sunroof switch 38 Turn terminal is grounded.
• 38 When the turn terminal is grounded roof control unit Twelve , 13 Stop the earth turn terminal 14 To ground the turn terminal.
• When the sunroof switch auto slide open to manipulation, of the sunroof switch auto slide (open) circuit is turned on Lou off control unit 33 , 34 Turn
terminal is grounded.
• 33 , 34 When the turn terminal is grounded roof control unit 13 Stop the earth turn terminal Twelve , 14 To ground the turn terminal.
• Sunroof motor has been detected it is performing an auto slide opening operation.
• When the sunroof switch auto slide to closing operation, the sunroof switch auto slide (closed) circuit is turned on Lou off control unit 33 , 36 Turn
terminal is grounded.
• 33 , 36 When the turn terminal is grounded roof control unit 13 , 14 Stop the earth turn terminal Twelve Ban terminal is grounded.
• Sunroof motor has been detected it is performing an auto slide closing operation.
• Auto slide closing operation is about the fully closed position 250mm It stopped before, and then will operate in fully closed by the slide closing operation.
RF - 10
Rear sunroof
PIIA9722J F
G
• sunroof SW Receiving a signal and the remote control signal, sunroof SW1 , Two , Three of ON - OFF
roof C / U Send the sunroof operating instructions to the sunroof motor by the combination of the signal.
• Buzzer signals from the sunroof motor One , Two It receives, to blowing each alarm buzzer.
sunroof SW Fully closed, pause, roof a signal such as a tilt-up operation C / U Send to.
It adopted a lock of Dogutaipu to lock and striker front sunroof, thereby improving the time of tilt operation. Sunroof frame H
It was adopted sunroof frame integral with the rail and linked to the rear sunroof.
Glass lid is opened and closed through a rear sunroof of the drive wire by mounting the motor to the sunroof frame
Drive wire
rear end and consolidated the link (rear guide).
KA
RF - 11
Rear sunroof
PIIA9721J
Roof control unit input and output signal reference value JIS003XM
Terminal Key
Signal name Operation or condition Reference value( V )
number SW
OCC3383D
( SW Pressed)
( SW Pressed)
RF - 12
Rear sunroof
Key
Signal name Operation or condition Reference value( V )
SW
operation ( SW Pressed)
( SW Pressed)
B
operation ( SW Pressed)
RF
KA
RF - 13
Rear sunroof
The following operations by checking the communication function between the sunroof motor and the roof control unit.
PIIA1963J
00 normal -
I do not want to migrate to the sunroof communication diagnosisThree . body CAN Communication diagnostic inspection (BCS-40)
RF - 14
Rear sunroof
1. The contents of to get the information from your failure to confirm the request.
2. To grasp the system overview. " System Overview "( RF-8 page ) See.
• CONSULT-II If you want to use is " CONSUL T - II Body by CAN Communication inspection "( BCS-39 page ) See.
B
• CONSULT-II If you do not use the "Self-diagnosis function ( CONSUL T - II If you do not want to use the ) "( BCS-40 page ) See.
Four. Carry out the sunroof communication diagnosis. " Sunroof communication diagnosis "( RF-14 page ) To see.
Five. From the phenomenon by fault diagnosis table, to repair or replace the cause of the failure. " Phenomenon by fault diagnosis "( RF-15 page ) To see.
C
6. Again, performing the operation check. If there is abnormal Two To implement the inspection again from the procedure.
7. Exit.
D
Phenomenon by fault diagnosis JIS003XO
sunroof SW During the operation, it does not slide actuated slide SW System inspection (RF-17)
sunroof SW During the operation, do not tilt operate Tilt SW System inspection (RF-18) E
sunroof SW During the operation, not auto-operate Auto SW System inspection (RF-20)
Not sunroof operate (sunroof SW , Both at the time the remote If such mechanical failure caught by the sunroof frame is not confirmed,
-
control operation) sunroof motor replacement
If the sunroof motor detects the positional deviation • The operation of the remote control is prohibited J
• And to motor lock the sunroof with tilt-up full-open position to return to
normal.
RF - 15
Rear sunroof
2. Use the switch monitor diagnosis, sunroof SW To inspect the. " Switch monitor "( BCS-44 page ) reference.
Inspection results
OK »Sunroof SW normal.
NG » Two What
Inspection results
OK »Normal
NG »Sunroof SW Exchange.
RF - 16
Rear sunroof
2. sunroof SW To operate the roof C / U Vehicle side harness connector 34 , 36 Point the voltage across the terminals turn-body earth
Biopsy to. B
terminal to
Measurement condition Voltage( V)
(+) ( - )
slide SW C
34 about 0
OPEN During operation
slide SW
36 about 0
CLOSE During operation
about Two
Body earth D
PIIA1812J
34
Other than those above
36
E
OCC3383D
Inspection results
OK » Two What
2. sunroof SW Sunroof motor vehicle side harness connector to operate the Three , Four , Five Between the turn pin-body earth
Measuring terminal
Measurement condition Voltage( V) H
(+) (-)
Three about 0
body
Four about 0
Earth slide SW OPEN During operation
Five about Twelve
RF
Three about 0
body
Four about Twelve
Earth slide SW CLOSE During operation
Five about Twelve PIIA9723J
J
Inspection results
NG » Three Measurement
KA
RF - 17
Rear sunroof
3. Sunroof motor vehicle side harness connector Three , Four , Five Ban terminal ~ roof C / U Vehicle side harness connector Twelve , 13 ,
Inspection results
PIIA9724J
2. Tilt SW To operate the roof C / U Vehicle side harness connector 37 , 38 To check the voltage between the turn pin-body earth.
Measuring terminal
Measurement condition Voltage( V)
(+) ( - )
Tilt SW
37 about 0
UP During operation
Tilt SW
38 about 0
DOWN During operation
about Two
Body earth
PIIA1817J
37
Other than those above
38
OCC3383D
Inspection results
OK » Two What
RF - 18
Rear sunroof
2. sunroof SW Sunroof motor vehicle side harness connector to operate the Three , Four , Five Between the turn pin-body earth
Measuring terminal B
Measurement condition Voltage( V)
(+) (-)
Three about 0
Body earth
Four Tilt SW UP During operation about Twelve
C
Five about 0
Inspection results
NG » Three What
3. Sunroof motor vehicle side harness connector Three , Four , Five Ban terminal ~ roof C / U Vehicle side harness connector Twelve , 13 ,
Inspection results
PIIA9724J
RF
KA
RF - 19
Rear sunroof
2. slide SW To operate the roof C / U3 Vehicle side harness connector 33 To check the voltage between the turn pin-body earth.
terminal to
Measurement condition Voltage( V)
(+) ( - )
slide SW
about 0
AUTO During operation
about Two
Body earth
33
PIIA1818J
OCC3383D
Inspection results
OK » Two What
2. sunroof SW Sunroof motor vehicle side harness connector to operate the Three , Four , Five Between the turn pin-body earth
Measuring terminal
Measurement condition Voltage( V)
(+) (-)
Five about 0
Inspection results
NG » Three Measurement
RF - 20
Rear sunroof
3. Sunroof motor vehicle side harness connector Three , Four , Five Ban terminal ~ roof C / U Vehicle side harness connector Twelve , 13 ,
14 Carry out the harness conduction inspection between the turn terminal.
B
C
Inspection results
slide SW To manipulate the, sunroof motor vehicle side harness connector Two , Six The voltage across the terminals turn-body earth to point inspection.
F
Measuring terminal
Measurement condition Voltage( V)
(+) ( - )
Sunroof in
Body earth about Eight
Six operation
Inspection results
OK »Normal
NG » Two What
KA
RF - 21
Rear sunroof
3. Sunroof motor vehicle side harness connector Two , Six Ban terminal ~ roof C / U Vehicle side harness connector Ten , Eleven Turn
Inspection results
PIIA9726J
Inspection results
RF - 22
Rear sunroof
3. Sunroof motor vehicle side harness connector Two , Three , Five , Six Turn end
B
Carry out the harness conduction inspection between the turn terminal.
Inspection results
OK »Normal.
E
Sunroof identification terminal circuit system inspection JIS004CJ
Inspection results
G
OK »Normal
PIIA2214J
RF
1. Remote control power inspection
Replace the batteries in the remote control, carry out the sunroof operation.
Inspection results
J
OK »No abnormality
NG » Two What
2. Remote inspection
KA
Inspection results
OK »Remote exchange
NG »Roof C / U Exchange
L
RF - 23
Rear sunroof
removal
" EI Exterior, interior "of "Headlining" ( EI-35 page ) reference.
attachment
Installation is carried out in the reverse order of removal.
RF - 24
Rear sunroof
Caution : When removing the sunroof unit and glass lid, sheet, trims and the body protected by a cloth, etc., wounded
To carry out prevention.
RF
KA
L
PIIA1600J
RF - 25
Rear sunroof
Glass lid
removal
1. Sunshade in the fully open position, support for the left and right sides of the glass lid
Caution : When removing the glass lid from the vehicle body, Two Carefully work in the name or more
attachment
2. By inserting a shim, tighten to the specified torque the nut on the diagonal.
3. Carry out the operation and Kenzuke inspection of the glass lid. " Kenzuke inspection "( RF-28 page ) reference.
Wind deflector
removal
2. Remove the screw that attach the left and right arm.
PIIA1602J
attachment
sunshade
removal
1. Remove the sunroof unit. Of "sunroof unit" "removal"( RF-27 page ) reference.
RF - 26
Rear sunroof
attachment
1. Installing a sunshade.
Sunroof unit
removal B
2. Remove the head lining. " EI Exterior and interior "of "Headlining" ( EI-35 page ) reference.
3. Rear display unit ASSY Remove the rear. (With rear display unit vehicles). " AV Audio, television, navigation C
Geshon telephone "of "Rear display unit ASSY Removal of, mounting "( AV-217 page ) reference.
Four. Remove the glass lid. Of "glass lid" "removal"( RF-26 page ) reference.
Five. In the sunroof unit front Two Remove the drain hose of the place. D
Caution : When removing the sunroof unit, because there is a risk of falling off Two To perform the work while supporting in the name or more.
attachment
1. Set the sunroof unit to the roof panel, temporarily fixed with a nut. G
2. Attach the sunroof bracket, temporarily stop of the vehicle body-side bolt.
3. Tighten the sunroof unit side rail portion of the nut to the specified torque on a diagonal line, the car then sunroof bracket
Tighten the side bolts to the specified torque. H
Four. Tightening of the nut and the motor bracket rear end portion of the bolt of the sunroof unit front end portion to the specified torque.
7. Carry out the operation and Kenzuke inspection of the glass lid. " Kenzuke inspection "( RF-28 page ) reference.
Caution : When Komu plug the drain hose, Do not use oil or soap water or the like.
Ten. Rear display unit ASSY The attach (with rear display unit vehicles). " AV Audio, TV,
Navigation phone "of "Rear display unit ASSY Removal of, mounting "( AV-217 page ) reference.
KA
11. Attaching the head lining. " EI Exterior and interior "of "Headlining" ( EI-35 page ) reference.
RF - 27
Rear sunroof
Sunroof motor
removal
2. Remove the head lining. " EI Exterior and interior "of "Headlining" ( EI-35 page ) reference.
Four. Remove the nut and the screw, remove the sunroof motor.
Caution : This is not rotated the sunroof motor removal after the motor
When.
PIIA1605J
attachment
1. While the motor of the gear adapt to the wire, parallel to the mounting the sunroof motor and the mounting surface, to the specified torque
tighten.
3. Attaching the head lining. " EI Exterior and interior "of "Headlining" ( EI-35 page ) reference.
Inspect the gap and surface difference between the glass lid and the roof panel, make adjustments as needed.
PIIA1606J
RF - 28
Rear sunroof
2. Remove the body side trim. " EI Interior and exterior "of "Removing, mounting" ( EI-28 page ) reference.
6. Tightening on the diagonal the glass lid to the specified torque, do a few times tilt and slide operation.
1. Remove the body side trim. " EI Exterior and interior "of "Removing, mounting" ( EI-28 page ) reference.
D
2. Loosen the nuts that attach the glass lid.
3. To adjust the height of the glass lid in the increase or decrease in the number of shims.
Four. Tightening on the diagonal the glass lid to the specified torque, do a few times tilt and slide operation.
E
Kenzuke After inspection, sunroof, in each door and window fully closed state, after flowing the water to the entire roof, conduct an inspection for any water leakage.
F
RF
KA
RF - 29
Rear sunroof
RF - 30