Professional Documents
Culture Documents
Fog Light PDF
Fog Light PDF
Installation instructions.
Retrofitting fog lights
BMW 3 Series Saloon (E 90)
BMW 3 Series Touring (E 91)
Installation time
Installation work will take approx. 2 hours; this time may vary depending on the condition and equipment
specification of the car.
The vehicle must be updated to the latest I-level status by flashing before installing the retrofit. Differing
programming times may be necessary depending on the production age of the vehicle and on work
previously performed on the vehicle.
The installation time given does not include time needed for programming/encoding.
The total costs for the programming time should be taken into account when calculating retrofitting
costs (reimbursement through warranty is not permissible).
Important notes
These installation instructions are intended in the first instance for use within the BMW dealer
organisation and by authorised BMW Service outlets.
The target group for these installation instructions is always skilled personnel who have been trained on
BMW vehicles and possess the corresponding specialist knowledge.
All work is to be performed using up-to-date BMW repair instructions, circuit diagrams, maintenance
manuals and procedural instructions in a rational sequence and with the specified tools (special tools),
taking into account the relevant safety regulations.
To avoid unnecessary extra work and/or costs, if any installation or function problems occur,
after a brief troubleshooting session (approx. 0.5 hours), contact the following:
1. Either your national sales company or your regional office or
2. The Support team via the Aftersales Assistance Portal (ASAP) using the optional technical
parts support application.
Quote the VIN and the part number of the retrofit kit and provide a detailed description of the
problem.
Do not file the printout of these installation instructions, as there are daily updates via ASAP!
See ASAP for explanations of the pictograms.
All illustrations show left-hand-drive vehicles; proceed in the corresponding manner when working on
right-hand-drive vehicles.
Notes on assembly
In some cases only the installation procedure for the left side of the vehicle is shown; proceed
correspondingly on the right side of the vehicle.
Chapter Page
1. Overview of parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Preliminary work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Overview of connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
B C
D E
' "" -
Legend
TIS No.
Perform brief test ---
Disconnect negative terminal of the battery 12 00 ...
A1 A3
A5
A4 A
A2
A6
&% " -
Item Designation Signal Cable colour/ Connection point in vehicle Brief desig-
cross- nation/slot
section
A Additional wiring harness --- --- --- ---
A1 Socket housing, 2-pin GR --- --- On right-hand fog light X769
A2 Socket housing, 2-pin GR --- --- On left-hand fog light X768
A3 Cable shoe, 6 mm Terminal BR At comb connector in engine compartment, X166
31 1.5 mm2 front right
A4 Cable shoe, 6 mm Terminal BR At comb connector in engine compartment, X165
31 1.5 mm2 front left
A5 Socket contact Terminal GE/BR On driver's footwell module X14261 module 2
55 VRA 1.5 mm2 PIN 37
A6 Socket contact Terminal GE On driver's footwell module X14260 module 1
55 VRA 1.5 mm2 PIN 03
B A 2
C 1 E D ' "# -
Legend
' "$ -
A3
Do the same on the left side. Screw
connecting point A4 of the additional wiring
harness A to comb connector X165.
A
X166
&% "" -
' #! -
' # -
A6
A5
E
' "% -
20 240
260
Install lights operating unit D.
100 km
1
1/2
R
BC
L
090 0048 E
2
' "'-
In the left-hand wheel arch, install fog light C as
1 described in TIS 63 17 060.
Use the screws (1) from the fog lights cover
(Fig. 0900049E) for fitting.
Slot connecting point A2 onto fog light C.
Do the same on the right side.
C
1
A2 ' # -
- Program/encode retrofit equipment with DISPlus, MoDIC III or GT-1 with the CIP application and
follow the operator prompting.
- Reconnect the car's battery.
- Perform a brief test.
- Perform a function test.
- Reassemble the vehicle.
- Check the fog light settings acc. to TIS PA 63 100 14.
A4011
55 V 55 V
37 3
X14261 X14260
A5 A6
1.5 1.5
GEBR GE
A2 A1
2 X768 2 X769
55 V 55 V
E26 E27
31 31
1 1
A2 A1
1.5 1.5
BR BR
X165 X166
31 31
KAR KAR
A4 A3
087 0051 E
Legend
All designations marked with * apply only for these installation instructions or this circuit diagram
Cable colours
BR Brown
GE Yellow