Professional Documents
Culture Documents
D E M C O B U T T E R F LY V A LV E S
Product Specifications
How to Order Valves 6
Base Numbers and Weights 9
Component Parts List 10
Dimensional Data (Valves) 12
How to Order (and Technical Information)
Handles 15
Worm Gear Operators 16
DR Piston Actuators 18
Diaphragm Actuators 22
Stem Extensions, Tees and Adapters 23
General Technical Information 24
Standard Material Data 29
Hard backed
cartridge seat
(2" - 36")
F E A T U R E S A N D B E N E F I T S p2
DEMCO B U T T E R F L Y V A L V E S DEMCO
designed to self-center in ANSI 150 14" to 48" size valves are available in torque and premature failure caused by
flange patterns. 150 and 50 psi drop tight shut off ratings elastomer distortion as found in other
Multiple pressure ratings as well as throttling. non-rigid seat designs; 3) simplifies seat
Three drop tight pressure ratings are Dry stem journal eliminates replacement because it is slip fitted into
offered for 2" to 12" sizes. The standard potential for leakage the body, with no need for special tools.
shut off pressure rating is 200 psi, but The DEMCO disc is uniquely designed Positively oriented disc
285 and 50 psi shut off ratings are also with a continuous annular raised land Proper orientation of the stem/disc
available. And, where drop tight closure around the stem hole and disc edge which connection is assured by the rectangular
is not required and minimal torque is presses into the seat flat at every angular drive. In 2" - 24" size valves, the disc is
desired, a throttling rated valve is avail- position. The resilient seat presses back permitted to float on the stem to perfectly
able. Both the 50 psi and throttling rat- with a higher specific force than the line center in the valve seat. This design
ings allow for smaller actuators, which pressure, preventing leakage to the stem. enhances drop tight sealing and prolongs
can significantly reduce overall installa- In addition, two O-ring ribs are provided service life.
tion cost in automated applications. The in the seat stem bore creating a triple End-of-line service
stem seal. Lug body valves may be used in end-of-
In competitive stem seal designs line service, with downstream piping
with boot seats, a seal is accomplished removed. (Only weld neck or socket
by an interference “squeezing” on the flanges can be used for this service.)
stem or an O-ring in the stem journal. Since upstream pressure is excluded
The potential for leakage behind the between the flange and the seat face by
seat is high for this competitive design. the exclusive DEMCO flange seal design,
As the disc wipes the seat, elongation of there is no effective force to slide the seat
A the stem seal area allows leakage to col- downstream. DEMCO 2" - 12" Lug
lect behind the seat. This condition is Butterfly Valves are suitable for liquid
eliminated by DEMCO’s dry stem journal service up to 200 psi with downstream
and hard-backed seat. piping removed (150 psi 14" - 36").
Hard-backed seat
Hard-backed cartridge seat (2"- 36") Lug body valves are recommended
The DEMCO cartridge seat is constructed for isolation of pumps, control devices
by permanently bonding a resilient elas- or other system components which may
tomer to a rigid backing ring. In addition need to be removed for repair or replace-
to superior sealing integrity, this design: ment. Lug valves are also suitable for
1) makes valve installation easier because installation at points from which piping
no special precautions are required for expansion may proceed. Such valves
disc position. This is especially advanta- are normally blanked with blind flanges,
geous when installing valves with fail to protect the exposed seats until new
closed actuators; 2) eliminates high piping is attached.
B
SPECIFICATIONS
Sizes Operating Temperatures
2" - 48" -30ºF to +300ºF (-34ºC to +204ºC)
Body type and style designations depending on seat material selection
Long neck NE-C and NF-C: 2" - 48", and application (see page 30)
2" - 36"wafer / lug, 42" - 48" flanged. Standard Material Options
Short neck NE-I, and NE-I Sanitary: Bodies: Iron, steel, stainless steel and
C
2" - 12" wafer / lug. bronze
NE-IT Teflon: 2" - 10" wafer / lug. Discs: Nickel plated ductile iron, bronze
NE-D: 2" - 12" wafer / lug. and stainless steel
Marine: 2" - 24" wafer / lug. Stems: 416 and 316 stainless steel
Pressure rating Seats: Buna N, EPT, Viton, Neoprene
2" - 12": 0 (Throttling), 50, 200 and 285 psi *Many more options available (see how
2" - 10" NEI-T: 150 psi to order, pages 6-8 and 29-30 or consult
14" - 48" 0, 50 and 150 psi factory)
D
F E A T U R E S A N D B E N E F I T S p3
S T Y L E S A N D A C C E S S O R I E S DEMCO
F E A T U R E S A N D B E N E F I T S p4
S T Y L E S A N D A C C E S S O R I E S DEMCO
Actuators
DEMCO Series DR pneumatic actuators
(A1) are available in double-acting or
fail-safe, spring return models. Series DR
actuators are compact, high-torque, piston
actuators. Series R diaphragm actuators
(A2) incorporate a heavy-duty, enclosed
rack-and-pinion linkage. Diaphragm actu-
ators are suitable for low-pressure, pneu-
matic service. Electric actuators (A3) are
used when compressed air is not avail-
able for pneumatic operations.
Handles and stem extensions
A1
Three basic handle designs interchange
DEMCO NE-C wafer with
Series DR actuator. on any 2" to 12" valves: ten position
locking, two position locking and memo-
B ry stop. Memory-stop handles provide
Stem extension throttling which is infinitely adjustable
with handle
and can be set by a lock nut with memo-
on Series NE-I
butterfly valve ry-stop setting (adjustable open stop).
Handles are available in basic trim, corro-
sion-resistant trim and sanitary trim. Stem
extensions are fabricated from carbon
steel parts and contained in a tubular
housing. Gaskets and O-rings seal the
stem extension at top and bottom. These
extensions are fabricated to specified
lengths.
Gear operators
DEMCO weatherproof gear operators are
offered with a choice of handwheel,
chain-wheel, or square nut. The worm
gearing has self-locking set screws to
control open and closed positioning or
A2
an optional adjustable memory stop for
Series R diaphragm actuator
“balance return” to a preset open
position after closing.
A3
C
Electric actuator
Gear operator
F E A T U R E S A N D B E N E F I T S p5
S E R I E S NE-C, NE-I, NE-D, N E I - T, 2" – 1 2 " DEMCO
How to Order (example: 6" NE-C, 200PSI, Wafer, Standard trim with handle 22124-1215311)
X X X X X – X X X X X X
P R O D U C T S P E C I F I C A T I O N S p6
S E R I E S NF-C, 1 4" – 2 4" DEMCO
How to Order (example: 18" NF-C, 150PSI LUG, SS trim, Buna-N seat, WGO. 23822-512231A)
X X X X X – X X X X X X
P R O D U C T S P E C I F I C A T I O N S p7
S E R I E S NF-C, 30"– 48" DEMCO
How to Order (Example: 42", 150 psi, bronze disc, EPT seat with Gear Op 24106-621435A)
X X X X X – X X X X X X
P R O D U C T S P E C I F I C A T I O N S p8
B U T T E R F L Y V A L V E S DEMCO
Marine Vavles: Consult factory for data sheets B-255, B-256 and B-258.
P R O D U C T S P E C I F I C A T I O N S p9
B U T T E R F L Y V A L V E S DEMCO
DEMCO Butterfly Valve Component Parts List: Series NE-C, NE-I, NE-D
Parts List for Series NE-C, NE-I, and NE-D (replacement parts for NE, NE-S, and NE-N, consult factory or company representative)
Ref Component Description 2" 21/2" 3" 4" 5" 6" 8" 10" 12"
#
1 Body NE-C Wafer 22137-012 22138-012 22139-012 22140-012 22141-012 22142-012 22143-012 22144-012 22145-012
ASTM A48 Gray Iron -012
NE-C Lug 21986-05x 21987-05x 21988-05x 21989-05x 21990-05x 21991-05x 21992-05x 21993-051 21994-051
Options ASTM A395 Ductile Iron -051, ASTM A48 Gray Iron -052
NE-I Wafer 22681-01x 22681-02x 22681-03x 22681-04x 22681-05x 22681-06x 22681-07x 22688-01x 22689-01x
Options ASTM A395 Ductile Iron -011, ASTM B148 Al. Bronze -013, ASTM A216 WCB Steel -014,
ASTM B179 Aluminum -015, DI/ENC -016, ASTM A351 SS -018
NE-I Lug 22695-05x 22696-05x 22697-05x 22698-05x 22699-05x 22700-05x 22701-05x 22702-05x 22703-05x
Options ASTM B148 Al. Bronze -053, ASTM A216 WCB Steel -054, ASTM A351 SS -058
NE-D Wafer 22187-021 22682-011 20594-021 22189-021 22190-021 22191-021 22687-011 22192-021 22689-011
Options ASTM A395 Ductile Iron - 0x1
2 SEAT 1786-xxx 1788-xxx 1790-xxx6 1792-xxx 1794-xxx 1002-xxx 1798-xxx 1815-xxx 1817-xxx
Options - 031 Buna-N, - 032 Black Neoprene, - 033 Hypalon, - 034 Viton, - 135 EPT1, - 036 Nat. Rubber
3" NE-D Seat (see below6) - 037 White Neoprene, - 231 Peroxide Cured Buna-N, - 244 Fluorosteam, - 331 ETM-30230
3 DISC 200 psi 22045-0xx 22046-0xx 22047-0xx 22048-0xx 22049-0xx 22050-0xx 22051-0xx 22052-0xx 22053-0xx
285 psi 22196-0xx 22197-0xx 22198-0xx 22199-0xx 22200-0xx 22201-0xx 22202-0xx 22203-0xx 22204-0xx
50 psi 22205-0xx 22206-0xx 22207-0xx 22208-0xx 22209-0xx 22210-0xx 22211-0xx 22212-0xx 22213-0xx
Throttling 22214-0xx 22215-0xx 22216-0xx 22217-0xx 22218-0xx 22219-0xx 22220-0xx 22221-0xx 22222-0xx
Options - 002 316 SS, - 003 Monel, - 005 Ni. Pltd. Duct Iron, - 007 Alloy 202, - 008 Hastelloy C, - 014 Alum. Bronze3
PVF Coated 200 psi 22714-001 22715-001 22716-001 22717-001 22718-001 22719-001 22720-001 22721-001 22722-001
4 UPPER STEM NE-C 22066-00x 22067-00x 22068-00x 22069-00x 22070-00x 22071-00x 22072-00x
NE-I 22073-00x 22074-00x 22075-00x 22076-00x 22077-00x 22078-00x 22079-00x
NE-D 22073-00x 22074-00x 22193-00x 22194-00x 22195-00x 22077-00x 22078-00x 22079-00x
UPPER STEM NE-C 22334-00x 22335-00x 22336-00x 22337-00x 22338-00x 22339-00x 22340-00x
-Utility Top NE-I 22341-00x 22342-00x 22343-00x 22344-00x 22345-00x 22346-00x 22347-00x
6 LOWER STEM 22080-00x 22081-00x 22082-00x 22083-00x 22084-00x 22085-00x 22086-00x
Stem Material Options - 001 416 SS, - 002 316 SS4, - 003 Monel, - 004 Phos. Coated Steel
7 SPRING PIN (2) 302 SS 5448-18720 5448-18724 5448-25028
14 RETAINER Stainless Steel 22117 13704 13705 13706 13707
22 TOP O-RING Buna-N 5526-114 5526-115 5526-117 5526-119 5526-125
23 STEM O-RING5 Buna-N 5526-113 5526-115 5526-116 5526-212 5526-214 5526-220
24 BEARING (2) Bronze 22526-001 22118-001 13112-001 13115-001 13116-001 13117-001
1 EPT Seat Options: Standard -135 Peroxide Cured, Food Grade -035 3 8” - 12”, 285 psi Alum. Bronze, use “-024”.
Peroxide Cured, -235 Sulfer Cured. 4 8” - 12”, Upper Stem 17-4 PH SS (p/n suffix -012), Lower Stem 316SS.
2 Alloy 20 not available for 285 psi. 5 4 required for throttling (0 psi) valves only.
6 3" NE-D Seat PN. 25095-xxx.
P R O D U C T S P E C I F I C A T I O N S p10
B U T T E R F L Y V A L V E S DEMCO
P R O D U C T S P E C I F I C A T I O N S p11
B U T T E R F L Y V A L V E S DEMCO
P R O D U C T S P E C I F I C A T I O N S p12
B U T T E R F L Y V A L V E S DEMCO
P R O D U C T S P E C I F I C A T I O N S p13
B U T T E R F L Y V A L V E S DEMCO
P R O D U C T S P E C I F I C A T I O N S p14
B U T T E R F L Y V A L V E S DEMCO
How to Order ( X X X X X - 0 0 X )
XXXXX – 00X
2 Position/10 Position Locking Handles Infinite Throttling with Memory Stop Handle
Standard 1 Dimension 2"- 4" 5"- 6" 8"- 12" Dimension 2"- 4" 5"- 6" 8"- 12"
M 9.50 11.00 15.00 M 9.50 11.00 15.00
Corrosion 2
N .85 1.07 1.13 N .87 1.07 1.13
Resistant
Sanitary 3
2 Position/10 Position Locking Handle Infinite Throttling with Memory Stop Handle
P R O D U C T S P E C I F I C A T I O N S p15
W E A T H E R P R O O F G E A R O P E R A T O R S DEMCO
Manual worm gear operators are self locking in all positions. enclose a ductile iron gear and hardened steel worm supported
Adjustment screws stop travel at open and closed positions. by bronze bearings. Standard external coating is green enamel;
Position indicator is standard on all models. Gearing is perma- white epoxy, coal tar epoxy and inorganic zinc primer available,
nently lubricated. Gray iron weatherproof case and cover special order.
How to Order, 2" – 12" (Example: 6" Gear Operator with Handwheel 22622-21352)
X X X X X – X X X X X
X X X X X X X – X X
P R O D U C T S P E C I F I C A T I O N S p16
W E A T H E R P R O O F G E A R O P E R A T O R S DEMCO
Optional Handwheel
Optional Chainwheel
Valves with chainwheels should be installed upside down
as noted to ensure pipe clearance and allow visual contact
with the position indicator.
P R O D U C T S P E C I F I C A T I O N S p17
DR S E R I E S P I S T O N A C T U AT O R S DEMCO
DEMCO Series DR Piston Actuators consist of two opposed pis- Consult the factory for complete data sheets showing mounting con-
tons with integral gear racks which are coupled to a common cen- figurations. Flatted stems are standard on 2"-12" Butterfly Valves
tral drive shaft to produce rotary motion. (NE-C, NE-I, NE-D), whereas 14"-48" NF-C utilize a keyed stem.
In the basic unit, the Body, Pistons and End Caps are alu- Series DR Actuators are available as Double-Acting or Spring
minum; the Central Drive Shaft is hard anodized, high perform- Return. Double-Acting is the most economical, requiring either air
ance Aluminum Alloy 70-75. The Fasteners are plated steel; the or hydraulic pressure for opening and closing (fail last position).
Seals are Buna-N. All units are totally enclosed and use gaskets Spring-Return Actuators use compression
for weatherproof operation. Carbon filled teflon guide bands sup- spring(s) to move valve in one direction, Remove indicator
for access to manual
override wrench flats
port the pistons to eliminate metal-to-metal contact during actua- while air pressure moves it in the
tor operation. As a result, piston o-rings designed for sealing are opposite direction. Spring Return
not required to perform bearing functions. Actuators are used when valves
Mounting the actuator to the valve for many popular sizes is must move to a predetermined
direct, requiring only a splined, aluminum stem adapter. Other sizes position upon air supply failure
may require the addition of an aluminum adapter plate, but still (fail open or fail closed).
make a closed coupled unit. Some sizes (mostly the larger valves) Actuator Torque Output (in-lb), Double Acting
will require the traditional steel brackets/coupling mounting kit.
Actuator Supply Pressure (psi)
Double Acting Actuator for NE-C, NE-I, NE-D and NF-C Model 40 60 80 100 120
Butterfly Valves
EDA40 204 310 416 513 620
Assembly Part Number Actuator
EDA65 310 469 628 788 947
Orientation
J024872-0 XX X X
Open
EDA100 460 699 929 1168 1398
285 psi Shut Off 225 326 510 765 1190 1530 2550 4125 7000 – – – – – – – – –
200 psi Shut Off 132 192 300 450 700 900 1500 2650 4500 – – – – – – – – –
150 psi Shut Off – – – – – – – – – 7740 10280 12600 15600 30000 50000 67500 107000 155000
50 psi Shut Off 108 108 192 264 450 550 1000 1800 3000 4500 6500 8400 10800 20000 30000 50000 79180 115000
Throttling* 72 72 90 108 144 180 350 700 1160 1660 2800 3400 5000 8400 – – – –
285 psi Shut Off 338 489 765 1148 1785 2295 3825 6188 10500 – – – – – – – – –
200 psi Shut Off 198 288 450 675 1050 1350 2250 3975 6750 – – – – – – – – –
50 psi Shut Off 162 162 288 396 675 825 1500 2700 4500 6750 9750 12600 16200 30000 – – – –
Throttling* 144 144 180 216 288 360 700 1400 2320 3320 5600 6800 10000 16800 – – – –
* When line velocity exceeds 15 feet per second, dynamic torque exceeds opening torque.
** For Series NEI-T Butterfly Valve torque requirement, consult factory.
P R O D U C T S P E C I F I C A T I O N S p18
DR S E R I E S P I S T O N A C T U AT O R S DEMCO
Spring Return Actuator ESA 400 through ESA 1600 for Actuator Orientation
NE-C, NE-I, NE-D and NF-C Butterfly Valves
Assembly Part Number Open Close
J024873- X XX X X
P R O D U C T S P E C I F I C A T I O N S p19
DR S E R I E S P I S T O N A C T U AT O R S DEMCO
Open Close
No. of Springs* Actuator Size Orientation Valve Size
8 Springs 4 2500 09 See drawing 0 4" 1
10 Springs 5 4000 10 See drawing 3 5" & 6" 2
12 Springs 6 4004 11 8" 3
14 Springs 10" 4
7
(Standard)
12" 5
14" 6
* Select from Orientation 0 Orientation 3
16" 7
Torque Chart Spring Close Spring Open
18"- 24" 8 (Stroke C & F) (Stroke D & E)
P R O D U C T S P E C I F I C A T I O N S p20
DR S E R I E S P I S T O N A C T U AT O R S DEMCO
OS
E
D OP
Off service. Independently adjustable SPDT Exhaust metering valves are available to control opening and
B
A
switch elements are arranged so that each end closing speed of the butterfly valve.
4-Way
of the valve travel is indicated by separate circuit closures. Solenoid
Valve
Declutchable Manual 3-Way
Positioners* Worm Gear Overrides Solenoid Valve
Pneumatic positioners are offered for modulating Declutchable Manual Worm
service. The standard signal range is 3-15 psi, and Gear Overrides are available for
may be generated by temperature, CL
OSE
D
OPE
N
OPE
size 40 through 4004 DR actuators. Especially applicable to
N
Optional
spring return actuators, the handwheel can be engaged with a
CL
special declutch lever to hold the valve in its last position until
Solenoid Valves* the actuator is returned to automatic operation.
Solenoid Valves are used to direct
supply air to the actuator to open and close the butterfly valve Series DR Actuator Seal Kit
at the command of an on/off electrical signal. Direct attachment Seal Kits consist of all rubber seals, Declutch
Lever
to the actuator through a manifold eliminates all external piping. bushings and guide bands required
Pressure connections are 1/4 NPT. Standard voltage is 120 to repair either double acting Manual
Handwheel
Override
VAC; other voltages are available on special order. NEMA 4 or spring return actuators.
Solenoid Valves for Double Acting Actuators 2172371-04 (NEMA 4 120 VAC)
2172371-07 (NEMA 7 120 VAC)
Solenoid Valves for Spring Return Actuators 2172385-04 (NEMA 4 120 VAC)
2172385-07 (NEMA 7 120 VAC)
Positioner Assembly, Electro Pneumatic for Double 2139067-12-04 (Orientation 0) 2139068-12-04 (Orientation 0)
Acting Actuators 4 MaDC Close, 20 MaDC Open 2139067-11-04 (Orientation 3) 2139067-11-04 (Orientation 3)
Positioner Assembly, Electro Pneumatic for Spring 2139069-12-04 (Orientation 0) 2139070-12-04 (Orientation 0)
Return Actuators 4 MaDC Close, 20 MaDC Open 2139069-11-04 (Orientation 3) 2139070-11-04 (Orientation 3)
P R O D U C T S P E C I F I C A T I O N S p21
D I A P H R A G M A C T U AT O R S DEMCO
Spring Diaphragm Actuators* valve. Diaphragms are made with steel case and diaphragm
Spring Diaphragm Actuators have the characteristics of spring- plates, Nylon-reinforced Buna-N
return cylinders but are applicable to lower air supply pressures. diaphragm, 303 SS stem and Buna-
The larger area of the diaphragm as compared to a cylinder pro- N seals. Rack-and-pinion compo-
vides greater force from the same supply pressure. DEMCO nents
Series R diaphragm actuators for butterfly valves with drilled are duc-
stems utilize a heavy-duty rack-and-pinion linkage to operate the tile iron
or steel.
Actuator Orientation
P R O D U C T S P E C I F I C A T I O N S p22
S T E M E X T E N S I O N S , T E E S A N D A D A P T E R S DEMCO
Stem Extensions Fabricated from carbon steel or Lengths from 3 inches to 16 feet are fabricated to order.
stainless steel, stem extensions are Torsional deflection of lengths over 16 feet requires special
contained in a tubular housing. design consideration and is available by special order only.
X X X X X – X X X X X X X X – X X X 0 0
Description 2"– 4" 5"– 6" 8" 10" 12" 14" 16" 18"– 20" 24"
Carbon Steel 23318 23319 23320 23321 23322 24529 24530 24531 24532
* Note: Consult factory for 30”, 36", 42", 48" valve stem extensions.
Base Part Orientation Valve Size Base Part Orientation Valve Size
Number Number
P R O D U C T S P E C I F I C A T I O N S p23
G E N E R A L T E C H N I C A L I N F O R M A T I O N DEMCO
Pressure Rating
Three drop tight pressure ratings are offered for DEMCO
Butterfly Valves. Normally, 200 psi shutoff is used in butterfly
applications. However, 285 psi shutoff is optionally available
for higher pressure applications. For smaller actuator sizing, 50
psi valves offer reduced torque.
For minimum torque, throttling valves, which do not pro-
vide drop tight closure, are available.
Wafer valve connection
Vacuum Rating
DEMCO Butterfly Valves will seal against 10 microns of vacu-
um (29.9 inches of mercury). For reduced torque and extended Marking
seat life, 50 psi discs are recommended for the dry service con- Each valve is positively identified by marking and tagging
ditions found in many vacuum applications. per MSS SP 25.
End-of-Line Service Actuation
Lug body valves may be used in end-of-line service, with Positive latch handles, worm gear operators and automatic
downstream piping removed. (Weld neck or socket flanges, actuators are available and totally interchangeable on the
only, can be used for this service.) Since upstream pressure is DEMCO valve.
excluded between the flange and the seat face by the exclusive The DEMCO top flange is dimensionally compatible with
DEMCO flange seal, there is no effective force to slide the seat other competitive butterfly valves. With optional “utility top”
downstream. DEMCO Lug Butterfly Valves are recommended stem, the DEMCO valve interchanges directly with competitive
for liquid service up to 200 psi with downstream piping valves, allowing valve replacement without the need for new actu-
removed. ation.
Lug body valves are recommended for isolation of pumps,
control devices or other system components which may need Installation and Maintenance
to be removed for repair or replacement. Lug valves are also DEMCO Butterfly Valves are bi-directional, with identical flow-
suitable for installation at points from which piping expansions way from either face. To install, simply close the valve, insert
may proceed. Such valves are normally blanked with blind between flanges and make up with studs or cap screws. No regu-
flanges, to protect the exposed seats, until new piping is lar maintenance or lubrication is ever required. Disassembly is
attached. simple, for inspection or replacement of parts. Open the valve,
remove handle or actuator, remove tangential pins, pull out the
stems and push the disc and seat out of the body. Reassemble in
reverse order, with a small amount of general purpose non-hydro-
carbon based lubricant on the outside of stems, seat and disc flats.
Steel or cast iron flanges of either raised or flat-faced type
are suitable for use with DEMCO Butterfly Valves. Plastic
flanges are subject to damage at installation by over-tightening
the bolting and may deflect or “cup,” resulting in flange leaks.
Refer proposed plastic flange installations to DEMCO Valve
Quotations Department for review and recommendation.
P R O D U C T S P E C I F I C A T I O N S p24
G E N E R A L T E C H N I C A L I N F O R M A T I O N DEMCO
P R O D U C T S P E C I F I C A T I O N S p25
G E N E R A L T E C H N I C A L I N F O R M A T I O N DEMCO
Length of Studs 5 51/2 51/2 53/4 61/2 61/2 7 71/2 81/4 81/4 10 101/2 113/4
Length of Cap Screws 11/2 11/2 11/2 13/4 13/4 2 21/4 21/4 21/2 21/2 31/4 31/2 4
†DEMCO Butterfly Valves are designed to seal without flange gaskets *2"–12" disc will open into Schedule 80 pipe ID.
against flange faces with inside diameters between slip-on flange
bore and Schedule 40 weld neck flange bore.
P R O D U C T S P E C I F I C A T I O N S p26
G E N E R A L T E C H N I C A L I N F O R M A T I O N DEMCO
90° 145 225 325 590 1,125 1,950 3,250 5,000 7500 10,000 13,600 18,000 22,600 30,000 47,000 70,000
80° 115 175 260 510 1,000 1,650 2,725 4,300 6,050 8,100 11,500 14,300 18,000 25,000 38,000 60,000
75° 95 135 215 410 830 1,350 2,200 3,600 5,000 6,700 9,500 12,100 15,000 21,000 31,500 48,000
70° 70 105 160 305 625 1,030 1,750 2,750 4,050 5,100 7,100 9,200 11,500 16,500 25,500 39,500
60° 53 83 125 235 490 800 1,300 2,150 3,100 4,100 5,100 7,100 8,700 11,750 18,000 28,000
50° 27 42 63 120 250 410 700 1,150 1,600 2,200 2,650 3,700 4,600 6,100 9,700 15,000
40° 17 26 38 73 155 250 420 670 1,000 1,300 1,700 2,300 2,800 3,800 6,000 9,200
30° 9 15 22 42 88 145 250 390 550 750 900 1,250 1,600 2,200 3,500 5,300
25° 6 10 15 28 60 98 170 260 380 500 650 900 1,125 1,500 2,300 3,500
0.14 Q
0.5 x 62.4
Time seconds =
= 305 x S (P)
D
Where:
= 305 x 0.707 Q = Flow in gpm.
S = Upstream pipe size in sq. ft.
Q = 215.6 gallons per minute
P = Pressure rating of the valve in psi.
What is the pressure drop across an 8" butterfly valve fully
open, flowing 2000 gallons per minute of solvent with a density Generally, a closing time of 6 to 8 seconds is sufficient to
of 55 pounds per cubic foot? eliminate water hammer.
Q2 x D
P =
CV2 x 62.4
(2000)2 x 55
=
(3250)2 x 62.4
P R O D U C T S P E C I F I C A T I O N S p27
G E N E R A L T E C H N I C A L I N F O R M A T I O N DEMCO
Cavitation Data output must meet or exceed the maximum torque requirement
of the valve.
Liquid flow is accelerated as it passes through a valve in such
Normal Wet Opening Torque requirements due to interfer-
a manner that pressure is decreased below the vapor pressure
ence are tabulated below. Dry service will increase opening
and bubbles form. Immediately downstream of the valve,
torque significantly. Consult factory for dry service torque
velocity decreases while pressure increases and the bubbles
requirements.
collapse causing noise and possible mechanical damage to the
The disc of a butterfly valve, in partially opened condition,
valve and piping. This is called cavitation. Cavitation can
is subject to “lift” forces from passage of fluid over its surfaces.
often be identified by the noise of the collapsing bubbles
This effect is analogous to an airplane wing and results in an
which sounds like gravel flowing in the pipe.
unbalanced turning force on the disc. Dynamic torque is pro-
Generally butterfly valves operate with high flow capaci-
portional to pressure drop through the valve and may become
ties and at low pressure differentials and are not particularly
significant in some applications.
susceptible to cavitation.
Dynamic torque typically is a maximum at about 70° disc
When butterfly valves are used as control valves, one can
opening. Under high differential pressure conditions, such
assure that cavitation will not occur by applying the following
torque may exceed the design strength of stems, connections or
simplified formula:
actuators. The curves at right may be used to calculate dynamic
Pmax = KC ( P 1 – P V ) torque for DEMCO Butterfly Valves and should be consulted in
Where: any case where high differential pressure may occur during
Pmax = Differential pressure across the valve. operation of a valve.
KC = Cavitation constant
(approximately .35 for butterfly
valves).
P1 = Inlet pressure (PSIA).
PV = Vapor pressure of the flowing liquid
(PSIA).
Example:
What is the maximum pressure drop possible through a butter-
fly valve at 100 PSIG inlet pressure with water at 68°F (.339
PSIA vapor pressure)?
Pmax = KC ( P 1 – P V )
Torque
The torque (turning effort) required to operate a given butter-
fly valve is determined by two factors: friction of disc and seat
due to interference, and dynamic forces of flow through the
valve which tend to open or close the valve. Actuator torque
285 psi Shutoff † 225 326 510 765 1190 1530 2550 4125 7000 — — — — — — — — —
200 psi Shutoff ‡ 132 192 300 450 700 900 1500 2650 4500 7740 10280 12600 15600 30000 50000 67500 107000 155000
50 psi shutoff 108 108 192 264 450 550 1000 1800 3000 4500 6500 8400 10800 20000 30000 50000 70000 —
Throttling* 72 72 90 108 144 180 350 700 1160 1660 2800 3400 5000 8400 16000 — — —
** When line velocity exceeds 15 fps, dynamic torque will exceed † 14"–24": 250 psi shutoff (14"-24": 250PSI–consult factory).
tabulated torque for throttling valves. ‡ 14"–24": 150 psi shutoff; 30"–36": 150 psi shutoff.
** Consult factory for dry torques.
P R O D U C T S P E C I F I C A T I O N S p28
S T A N D A R D M A T E R I A L D A T A DEMCO
Bodies
NF-C NF-C NF-C NE-I
Description NE-C NE-I NE-D NEI-T
14-24 30 & 36 42 & 48 Sanitary
Discs
NF-C NF-C NF-C NE-I
Description NE-C NE-I NE-D NEI-T
14-24 30 & 36 42 & 48 Sanitary
Ductile Iron/
Nickel Plated
A536 (65-45-12) • • • • • •
Ductile Iron/
SS Edge
A536 (65-45-12) • •
Ductile Iron/
PVF Coated
A536 (65-45-12) • • • •
Aluminum Bronze
B148 (954) • • •
B148 (955) • • •
316 SS A743 (CF8M) • • • • • • • •
Monel‡ QQ-N-288 • • • •
Alloy 20,
29 NI-20 Cr
A743 (CN-7M) • • • •
Hastelloy C‡
61 NI-17 Mo-17 Cr
A494 (CW-2M) • • • •
Stems
NF-C NF-C NF-C NE-I
Description NE-C NE-I NE-D NEI-T
14-24 30 & 36 42 & 48 Sanitary
P R O D U C T S P E C I F I C A T I O N S p29
S T A N D A R D M A T E R I A L D A T A DEMCO
Seats
See pages 6, 7 and 8 for seat material description and part num- VITON 1 is excellent at elevated temperatures and also in harsh
ber scheme for available options for different valve series. chemical environments. Viton is not suitable for hot water or steam.
+20°F to +300°F Same as Fluoroelastomer
Buna N is a general purpose elastomer compounded for maxi-
NATURAL RUBBER is generally superior to other elastomers
mum hydrocarbon or petroleum resistance.
in abrasion resistance and is recommended for dry material
0°F to +180°F Same as Nitrile, Hycar 1, NBR
handling. Use in oils and solvents is not recommended.
GENERAL SERVICE EPT is recommended for water serv- –30°F to +150°F
ice. Resistance to saturated steam to 275°F is excellent. EPT is
FLUOROSTEAM seats offer heat and chemical resistance to
suitable in alkaline solutions. EPT is not suitable for oil or
hydrocarbons and hot water or saturated steam. Maximum tem-
hydrocarbons. Peroxide cured +20°F to +275°F
perature capability is dependent on fluid resistance, pressure
FOOD GRADE EPT is formulated in compliance with FDA and flow rates.
guidelines published in the Code of Federal Regulations, Title +20°F to +275°F
21, paragraph 177.2600. This material is suitable for food serv-
ETM—30230 is compounded to combine many of the better
ice, except milk and edible oils.
media properties of Buna-N, EPT or Neoprene for service in
Peroxide cured +20°F to +275°F
Same as EPDM, Nordel1 hydrocarbons, gasoline, solvents, animal oils and vegetable oils
Sulfur cured –30°F to +225°F
with a wide temperature range (–30°F to 230°F). Abrasion
BLACK NEOPRENE complies with FDA guidelines and is resistance is equal to Buna-N. Resistance to hydrogen sulfide
principally recommended for food and beverage service. It is and carbon dioxide are superior to Buna-N.
resistant to vegetable oils, brine and oxygen. –30°F to +230°F
0°F to +180°F Same as Polychloroprene, CPE
NEI-T TEFLON 1 SEAT is Buna-N, or EPT elastomer bonded
WHITE NEOPRENE offers chemical resistance comparable to a virgin TFE covering providing an inert, aseptic non-stick
to black neoprene but uses fillers other than carbon black to surface which is excellent for sanitary food service applications.
provide white coloration. Physical properties are not as good as 0°F to +250°F
black neoprene, and white neoprene should be used only when
OTHER SEAT ELASTOMERS are available for special
black cannot be tolerated. Storage should be under low light
applications. Consult factory.
conditions to prevent discoloration.
0°F to +180°F
P R O D U C T S P E C I F I C A T I O N S p30
T E R M S A N D C O N D I T I O N S
1. CONTRACT ACCEPTANCE: fuel, power or transportation, breakdown of receives notice from Buyer of any alleged
Any written or oral purchase order received equipment or any other causes beyond Seller’s defect in or nonconformance of any product or
from Buyer by Cooper Cameron Corporation, reasonable control, whether of similar or dis- repair and if in the Seller’s sole judgment the
Cameron Division and Cooper Cameron Valves similar nature than those enumerated. Seller product or repair does not conform or is found
(“Seller”) shall be construed as a written accept- shall have additional time within which to per- to be defective in material or workmanship,
ance of Seller’s offer to sell and shall be filled in form as may be reasonably necessary under the then, Buyer shall, at Seller’s request, return the
accordance with the terms and conditions of circumstances and shall have the right to appor- part or product F.O.B. to Seller’s designated
sale set forth herein. SELLER’S ACCEPTANCE OF tion its production among its customers in such plant or service location. Seller, at its option and
THIS ORDER IS EXPRESSLY CONDITIONED ON a manner as it may consider to be equitable. expense, shall repair or replace the defective
BUYER’S ASSENT TO THE TERMS CONTAINED Seller reserves the right to furnish commercially part or product, or repay to Buyer the full price
HEREIN. The terms and conditions of Seller’s equivalent or better substitutes for materials or paid by Buyer for such defective part, repair or
proposal (if any) and acknowledgement shall to subcontract the Buyer’s order or portions product. Any repayment of purchase price shall
prevail over any conflicting or different terms in thereof as Seller deems necessary. In no event be without interest.
Buyer’s order unless Buyer notifies Seller in writ- shall Seller be liable for any consequential dam- Seller’s warranty liability, including defects
ing of its objections thereto within fifteen (15) ages for labor resulting from failure or delay in caused by Seller’s negligence, shall be limited to
days from receipt of Seller’s acknowledgement. shipment. If Buyer requires drawings, proce- such repair, replacement or refund, and shall
Buyer’s standard terms of purchase will not be dures, standards or similar material for not include claims for labor costs, expenses of
considered a counteroffer to Seller’s terms and approval, shipping schedules will be calculated Buyer resulting from such defects, recovery
conditions of sale. The failure of Seller to object from the time such approvals are received by under general tort law or strict liability or for
to any provision in conflict herewith whether Seller, since shipping schedules are based on damages resulting from delays, loss of use, or
contained on Buyer’s purchase order or other- Seller having all required information and a other direct, indirect, incidental or consequen-
wise shall not be construed as a waiver of the firm order from Buyer which is enterable into tial damages of any kind. Seller will not be
provisions hereof nor as an acceptance thereof. production. Any hold points, witness points or responsible for failures of products which have
the need for inspection by Buyer’s representa- been in any way tampered with or altered by
2. QUOTATIONS AND PRICES: tives must be identified by Buyer at the time of anyone other than an authorized representa-
All quotations are made for prompt acceptance quotation (if any) and/or order placement in tive of Seller, failures due to lack of compliance
and any terms quoted therein are subject to order that the effect on the prices or shipping with recommended maintenance procedures or
change without notice after thirty (30) days schedules (if any) can be taken into account. products which have been repaired or altered
from the date quoted unless specifically stated Additional inspection or testing required by in such a way (in Seller’s judgment) as to affect
otherwise on the quotation. Any product, serv- Buyer which affects normal production the products adversely. THIS WARRANTY IS
ice capability or manufacturing capability which sequence will be considered as extending the EXPRESSLY IN LIEU OF ALL OTHER WAR-
may be available at the time a quotation is shipping dates accordingly. RANTIES, EXPRESS, STATUTORY OR IMPLIED,
made is subject to prior sale. Prices quoted are INCLUDING THE WARRANTY OF MER-
5. MINIMUM BILLING:
valid for thirty (30) days unless specifically stat- CHANTABILITY AND FITNESS FOR PARTICULAR
ed otherwise on the quotation and are subject Seller reserves the right to impose a minimum PURPOSE WHICH EXCEED THE FOREGOING
to change without notice. The price in effect at billing charge on all sales, change orders or WARRANTY.
the time of shipment including any escalation order supplements.
9. NUCLEAR SALES:
formula will apply, unless a valid quotation or 6. TERMS OF PAYMENT:
written agreement to the contrary exists The products sold hereunder are not designed
Terms of payment for all materials and service or manufactured for use in or with any atomic
between Buyer and Seller. All prices shown are
are 30 days from invoice date, at net price, pro- installation or activity. If the Buyer or ultimate
in U.S. dollars and are F.O.B. Seller s shipping
vided satisfactory credit has been established. user of these products intends to use them in
point. Any documentation pertaining to trace-
All unpaid invoices are subject to the maximum such an installation or activity, Seller’s Nuclear
ability requirements for raw materials or prod-
legal interest rate per annum commencing with Terms of Sale shall be part of and control this
ucts or documentation required for any routine
the due date. contract. Seller will furnish Buyer with a copy of
or special processes must be identified by the
Buyer at the time of quotation (if any) or at the 7. CANCELLATIONS AND RETURNS: its Nuclear Terms of Sale upon request.
time of order placement. Purchase orders once placed by Buyer and 10. PATENT INFRINGEMENT:
3. TAXES: accepted by Seller can be canceled only with Seller warrants that the use or sale of material
Seller’s written consent and upon terms which or apparatus sold or rented by it to Buyer here-
Any tax or other charge imposed by law on the
will save Seller from loss. No products may be under will not infringe United States’ patents of
sale or production of goods or the performance
returned for credit or adjustment without writ- others covering such material or apparatus by
of services shall be paid by the Buyer, unless the
ten permission from Seller’s office authorized to itself, and hereby agrees to indemnify Buyer
law specifically provides that such payment
issue such permission. against judgment for damages for such
must be made by Seller, in which case Buyer
shall reimburse Seller for such payment as part 8. WARRANTIES: infringement of any such patent, provided that
of the purchase price. Custom duties, consular Buyer shall, upon receipt of any claim for
All products of Seller’s manufacture are war-
fees, insurance charges and other comparable infringement of any such patent or threat of
ranted against defects of material and work-
charges will be borne by Buyer. suit for such infringement or upon the filing of
manship for a period of twelve (12) months
any suit for infringement, whichever comes
4. SHIPPING SCHEDULE AND from the date of installation or eighteen (18)
first, promptly notify Seller in writing and
months from date of shipment, whichever peri-
DELIVERY: afford Seller full opportunity, at its option and
od first expires, when such products are used in
Shipment schedules are given as accurately as its own expense, to answer such claim or threat
the service and within the pressure range for
conditions permit and every effort will be made of suit, assume the control of the defense of
which they were manufactured. In the case of
to make shipments as scheduled. Seller will not said suit, and settle or compromise same in any
products or parts not wholly of Seller’s manu-
be responsible for deviations in meeting ship- way Seller sees fit. Other than court-awarded
facture, Seller’s liability shall be limited to the
ping schedules nor for any losses or damages to judgments as aforesaid Seller shall not be liable
extent of its recovery from the manufacturer of
Buyer (or any third party) occasioned by devia- for any delays, loss of use or for other direct,
such products or parts under its liability to
tions in the shipping schedule, whether due to indirect, incidental or consequential damages
Seller.
Acts of God, orders bearing priority ratings incurred by reason of any such judgment. Seller
Any repair work performed by Seller is war-
established pursuant to law, differences with does not warrant that such material or appara-
ranted for one year from completion of such
workmen, local labor shortages, fire, flood, tus (a) will not infringe any such patent when
repairs and applies only to work performed.
shortages or failure of raw materials, supplies, not manufactured by or for Seller or when spe-
If, within these specified periods, Seller
T E R M S A N D C O N D I T I O N S p31
T E R M S A N D C O N D I T I O N S
cially made in whole or in part to the Buyer’s 16. TRANSPORTATION CHARGES, 18. INDEMNIFICATION AND
design specification and such infringement aris- ALLOWANCES, CLAIMS: LIMITATION OF LIABILITY:
es from the inclusion of such specified design or All prices are F.O.B. Seller’s plant or other desig- A. INDEMNIFICATION:
(b), if used or sold in combination with other nated shipping point. Seller agrees to indemnify Buyer and hold
material or apparatus, or if used in the practice No freight is allowed unless stated in Seller’s Buyer harmless against any claims, demands or
of a process, will not, as a result of such combi- quotation (if any) or in a written contract which causes of action for property damage or per-
nation or use, infringe any patent covering such may exist between Seller and Buyer at the time sonal injury (including death) caused by the
combination or process; and Seller shall not be of shipment. If Seller’s quo-tation or a written negligent act or omission of any employee,
liable for and does not indemnify Buyer for contract states that all or a portion of freight is agent or subcontractor of Seller and not con-
damages or losses of any nature whatsoever allowed, all prices are F.O.B. Seller’s plant or tributed to by the negligence of Buyer, its
resulting from actual or alleged patent infringe- other designated shipping point, with most employees, its agents or any third party. Seller
ment arising pursuant to (a) or (b) above. economical surface transportation allowed. If shall not be responsible for the acts and work-
11. SELLER’S RIGHT TO the quoted or contractual price includes trans- manship of employees, agents, contractors or
portation, Seller reserves the right to designate subcontractors of Buyer or any third party, nor
MANUFACTURE:
the common carrier and to ship in the manner for failure or malfunction of any tools, materi-
Seller in its sole discretion shall have the right it deems most economical. Added costs due to als, equipment, products, supplies, facilities or
to manufacture the products provided hereun- special routing requested by the Buyer are devices not manufactured and supplied by
der as far in advance of its estimated shipping chargeable to the Buyer. Under no circum- Seller. Buyer agrees to hold Seller harmless from
schedule as it deems appropriate. Seller express- stances is any freight allowance which is any and all losses, claims, or damages arising
ly reserves the right to change or modify the absorbed by Seller to be deducted from the sell- from subsurface damage, surface damage
design and construction of any product in due ing price. If the quoted price or contract caused by subsurface damage, loss of hydrocar-
course of Seller’s manufacturing procedure includes transportation, no deduction will be bons and from pollution, regardless of whether
without incurring any obligation or liability to made in lieu thereof whether Buyer accepts such damages, losses or claims were caused by
furnish or install such changes, modifications or shipment at plant, warehouse, freight station, the negligence or sole negligence of Seller, it
improvements to products previously or subse- or otherwise supplies its own transportation. being the intent of the parties that this indem-
quently sold. When sales are made from the Seller’s ware- nity shall apply to property of Buyer or to that
12. ENGINEERING AND SERVICE: house, Seller reserves the right to charge either of any third party.
Upon request, Seller will provide engineering actual or pro-rated freight from Seller’s princi- B. LIMITATION OF LIABILITY:
and/or technical information regarding its prod- ple point of manufacture to Seller’s warehouse. UNDER NO CIRCUMSTANCES SHALL SELLER BE
ucts and their uses and, if feasible, will provide Buyer assumes risk of loss upon delivery to the LIABLE FOR ANY SPECIAL, CONSEQUENTIAL OR
personnel to assist Buyer in effecting field carrier, regardless of who pays shipping costs. INCIDENTAL DAMAGES, INCLUDING, BUT NOT
installations and/or field service. Any such infor- Seller endeavors to pack or prepare all ship- LIMITED TO LOSS OF ANTICIPATED PROFITS,
mation, service or assistance so provided, ments so that they will not break, rust or deteri- LOSS OF USE OF EQUIPMENT OR OF ANY
whether with or without charge, shall be advi- orate in transit, but does not guarantee against INSTALLATION, SYSTEM OR FACILITY INTO
sory only. In that regard, neither Seller nor such damage. Unless requested in writing by WHICH SELLER’S EQUIPMENT MAY BE LOCATED
Buyer assumes any liability for the acts or omis- the Buyer, no shipments are insured by Seller OR AT WHICH SELLER, ITS AGENT OR SUBCON-
sions of the other party except as may be pro- against damage or loss in transit. Seller will TRACTOR MAY BE PERFORMING WORK. Seller’s
vided in these terms. place insurance as nearly as possible in accor- total responsibility for any claims, damages,
dance with Buyer’s written instructions but in losses or liabilities arising out of or related to its
13. LABOR STANDARDS: such case Seller acts only as agent between the performance of this contract or the products or
Seller hereby certifies that these products were insurance company and the Buyer and assumes services covered hereunder shall not exceed the
produced in accordance with all applicable no liability whatsoever. purchase price.
requirements of Section 6, 7 and 12 of the Fair Any claims for shipping loss, breakage or
19. MODIFICATION, RESCISSION
Labor Standards Act as amended and of regula- damage (obvious or concealed) are Buyer’s
tions and orders of the United States responsibility and should be made to the carri- & WAIVER:
Department of Labor issued under Section 14 er. All claims regarding shortages must be made The terms herein may not be modified or
thereof. within thirty (30) days from receipt of shipment rescinded nor any of its provisions waived
and must be accompanied by the packing list(s) unless such modification, rescission or waiver is
14. INSPECTION: covering the shipment. in writing and signed by an authorized employ-
Unless otherwise agreed in writing, final inspec- ee of Seller at its office in Houston, Texas.
tion and acceptance of products must be made 17. CONSULAR INVOICES: Failure of Seller to insist in any one or more
at Seller’s plant or other shipping or receiving Consular fees for legalizing invoices, stamping instances upon the performance of any of the
point designated by Seller and shall be conclu- bills of lading, or other documents required by terms and conditions of the contract or the fail-
sive except as regards latent defects. Buyer’s the laws of any country or destination are not ure of Seller to exercise any of its rights hereun-
representatives may inspect at the Seller’s plant included in quotations or selling prices. If der shall not be construed as a waiver or relin-
or shipping point during working hours prior to instructed in writing, Seller will make arrange- quishment of any such term, condition, or right
shipment in such manner as will not interfere ments for consular documents and declarations hereunder and shall not affect Seller’s right to
with operations. as agent of the Buyer, but Seller assumes no lia- insist upon strict performance and compliance
bility whatsoever as a result of making such with regard to any unexecuted portions of this
15. DELIVERY AND ACCEPTANCE: arrangements. Seller assumes no responsibility contract or future performance of these terms
Delivery shall be in accordance with the for any fines or other charges imposed due to and conditions.
requirements in the Purchase Contract, provid- errors or incorrect declarations. All orders must be accepted by an author-
ed, in the event Buyer is unable to accept deliv- ized employee of Seller. The rights and duties
ery upon completion of the manufacture of the of the parties and construction and effect of all
Goods in accordance with such requirements, provisions hereof shall be governed by and con-
Buyer agrees that (i) title shall pass to Buyer on strued according to the internal laws of the
date of Seller’s invoice, and (ii) Buyer will make State of Texas. Any disputes which arise under
payments within thirty days after date of such this agreement shall be venued in the District
invoice. Seller shall retain risk of loss until deliv- Court of Harris County, Texas or in the Southern
ery is made in accordance with such require- District of Texas.
ments.
T E R M S A N D C O N D I T I O N S p32
T R A D E M A R K I N F O R M A T I O N
Cameron®
Demco®
DynaCentric®
DynaSeal®
Foster®
Pow-R-Seal®
Saf-T-Seal®
Thornhill Craver ™
Unibolt ™
W-K-M®
T R A D E M A R K I N F O R M A T I O N p33
USA Argentina Other Locations
Cooper Cameron Valves Cameron Argentina S.A.I.C. Austria
16500 South Main Street Av. Antartida Argentina 2711 Australia
Missouri City, TX 77489-1300 CC No. 2 Brazil
Phone: 281-499-8511 2800 Zarate, Pica Buenos Aires Brunei
Fax: 281-499-6965 Phone: 54-487-22297 Chile
Fax: 54-487-23404 Congo
UK Egypt
Cooper Cameron Valves Singapore England
Houstoun road Cooper Cameron (Singapore) Gabon
Livingston, West Lothian Pte. Ltd. Germany
Scotland, EH545BZ No. 2 Gul Circle Hungary
Phone: 441-506-444-000 Jurong Industrial Estate Indonesia
Fax: 441-506-441-320 Locked Bag Service No. 3 Ireland
Jurong Town Post Office Japan
Canada Singapore 2262 Malaysia
Cooper Cameron Corporation Republic of Singapore Netherlands
715-5th Ave. S.W. #600 Phone: 65-861-3355 New Zealand
Calgary, Alberta T2P 2X6 Fax: 65-861-6197 Nigeria
Canada Norway
Phone: 403-261-2800 France Oman
Fax: 403-262-5181 Cameron France, S.A. Poland
Plaine Sainte-Pierre Qatar
Mexico CS 620 Russia
Cooper Cameron de Mexico 34535 Beziers Cedex Saudi Arabia
S.A. de C.V. Beziers, France UAE
Avenida Homero 1804, Phone: 33-467-111500 Venezuela
Suite 403 Fax: 33-467-111600
Col. Chapultepec Morales,
11510 Mexico, D.F. Mexico.
Phone: 52-5-580-0296
Fax: 52-5-395-8669
COOPER CAMERON
VA LV E S
©Cooper Cameron Corporation, Cooper Cameron Valves Division Printed in USA 12/01 TC1629