Professional Documents
Culture Documents
AN7171NK, AN7176K
Dual BTL 14W Audio Power Amplifier Circuits
0.6±0.2
viding high reliability. The circuits can be turned on or off
29.96±0.3
20.0±0.25
28.0±0.3
29.6±0.3
with supply pins energized, because the stand-by circuit
is built-in.
ue e/ 0.6
R1.8
1.778
■ Features
• Two BTL 14W outputs built-in 1
2.66
tin nc
• Stand-by circuit built-in 2.8±0.3 12.5±0.3 3.5±0.3
e)
(4.06)
d
(14.1)
• Various protective circuits (for
(0.25)
temperature, or against
yp
1.2±0.1
2.54±0.8
dt
over-voltage, short-circuit between output and earth
on e.
1.45±0.25
ue
and between output and VCC, load short-circuit)
isc ag
1.8±0.25
tin
• Small shock noise at power ON/OFF
, d st
(1.2)
on na
1.45±0.25
ed cle
• Fewer external components required
Fin-attached 16-lead ZIP package (EZIP016-P-0660)
yp cy
• Good oscillation stability
d t ife
ue t l
tin uc
sc te
on rod
isc r P
d d fou
Di ain
ne ng
pla wi
e, ollo
typ s f
ce de
■ Block Diagram
an clu
en in
M
int ed
NF (Ch.1) NF (Ch.1)
ma inu
8 7
e, ont
typ isc
STAND-BY 5 Stand-by
Protection Circuit
ed M
Circuit
15 GND
(p
11 9
NF NF
(Ch.2) (Ch.2)
ICs for Audio Common Use AN7171NK, AN7176K
■ Pin Descriptions
Pin No. Pin Name Pin No. Pin Name
1 VCC 9 Negative Feedback Ch.2
2 Output Ch.1 (+) 10 GND (Input)
3 GND (Output Ch.1) 11 Negative Feedback Ch.2
4 Output Ch.1 (–) 12 Input Ch.2
5 Stand-by 13 Ripple Filter
6 Input Ch.1 14 Output Ch.2 (–)
7 Negative Feedback Ch.1 15 GND (Output Ch.2)
8 Negative Feedback Ch.1 16 Output Ch.2 (+)
ue e/
■ Absolute Maximum Ratings (Ta= 25˚C)
Parameter Symbol Rating Unit
Supply Voltage VCC Note 1) 24 V
tin nc
e)
Peak Supply Voltage VCC (surge) Note 2) 50.0 V
d
yp
Supply Current ICC 6.0 A
dt
on e.
ue
Power Dissipation PD Note 3) 37.5 Note 4) W
isc ag
tin
Operating Ambient Temperature Topr – 30 ~ + 75
, d st
˚C
on na
ed cle
Storage Temperature Tstg – 55 ~ + 150 ˚C
yp cy
Note 1) When no signals
d t ife
Note 2) Time = 0.2s
ue t l
tin uc
Note 3) Rθj – c = 2˚C/W
sc te
ne ng
pla wi
int ed
Output Noise Voltage Note) Vno Vin= 0mV, Rg= 10kΩ 0.60 1.50 mVrms
e, ont
12 46
PO
1.0 1.0 1.0
VCC = 13.2V
8 RL = 4Ω 0.8
PO = 1W
0.6
0.1 THD 0.1
4 0.4
THD
ue e/
0.2
0 0.01 0.01 0
4 8 12 16 20 0.1 1 10 100 10 100 1k 10k 100k
Supply Voltage VCC (V) Input Voltage Vin (mV) Frequency f (Hz)
tin nc
e)
d
yp
dt
on e.
ue
isc ag
tin
GV, THD – VCC ICQ – VCC
, d st
on na
ed cle
10 200
f = 1kHz
yp cy
RL = 4Ω 9
d t ife
Vin = 3mV GV
Total Harmonics Distortion THD (%)
52 160
ue t l
8
tin uc
Quiescent Current ICQ (mA)
50 7
sc te
on rod
Voltage Gain GV (dB)
48 6 120
isc r P
d d fou
46 5
Di ain
ne ng
44 4 80
pla wi
42 3
e, ollo
40 2 40
typ s f
ce de
38 1
an clu
THD
36 0 0
en in
M
3 4 5 6 7 8 9 10 11 4 8 12 16 20
int ed
■ Precautions on use
ce /D
an ce
1. Always attach an outside heat sink to use the chip. In addition, the outside heat sink must be fastened onto a chassis for use.
en an
4. The temperature protective circuit gets actuated when Tj = approx. 150˚C, but it is automatically reset when the chip
ed M
7. The load short-circuit protective circuit starts the protective operation at 0.3Ω or less of contact resistance.
(p
8. The atmospheric fault protective circuit protects the chip only from short-circuit between pins.
9. Take into consideration the heat radiation design particularly when VCC is set high or when the load is 2Ω.
ICs for Audio Common Use ICs for Audio Common Use
■ Application Circuit
VCC =13.2V
+
2000µF
VCC Pin –
1
IN Ch.1
– +
6
1µF 2
8
+ OUT Ch.1
100µF GND 3
– 4Ω
7
0.047µF 4
0.1 0.1µF
200Ω
µF
2.2Ω 2.2Ω
GND (Input side) AN7171NK
10 13 Ripple Filter Pin
AN7176K +
200µF
IN Ch.2 –
ue e/
– +
12
1µF 16
+
9
OUT Ch.2
100µF GND 15 4Ω
–
11
tin nc 0.047µF 14
e)
0.1µF
d
0.1
200Ω
yp
µF
2.2Ω 2.2Ω
dt
5
on e.
ue
isc ag
(STAND-BY)
tin
, d st
on na
ed cle
yp cy
+5V (Stand-by mode)
AN7171NK : 0V
d t ife
ue t l
tin uc
AN7176K : +5V
sc te
ne ng
AN7171NK, AN7176K
typ s f
ce de
an clu
en in
M
int ed
2.2Ω
ma inu
GND
e, ont
0.1µF
typ isc
+ –
an ce
100µF
en an
– +
1µF
+
int ten
200µF
0.1µF
ma ain
ed M
0.1µF 2.2Ω
lan
IN 2 IN 1
(p
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
ue e/
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
tin nc
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
e)
d
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
yp
defect which may arise later in your equipment.
dt
on e.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
ue
isc ag
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
tin
, d st
on na
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
ed cle
yp cy
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
d t ife
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
ue t l
tin uc
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
sc te
on rod
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
isc r P
ne ng
pla wi
e, ollo
typ s f
ce de
an clu
en in
M
int ed
ma inu
e, ont
typ isc
ce /D
an ce
en an
int ten
ma ain
ed M
lan
(p