Professional Documents
Culture Documents
This spreadsheet carries out a design for WUD Type 1 Thrust Blocks.
The method used here is the method recommended in the manual for granular soils
Data is entered into the coloured boxed cells in the worksheet THRUST1
Parameters for the design case(such as diameter, bend angle, test pressure, pipe cover)
are entered into the column in the DESIGN TABLE for each design case.
General Design Parameters, such as soils data etc, are entered in the cells in
the SOIL AND GENERAL DATA Section below the Design Table.
Notes
The formulae in column I are obtained by copying the corresponding cell in column G, converting the format to text and ed
Revision Record
Version Date by checked Notes
Page 1
About
gorised software
s are responsible for
ng their own calculations.
Page 2
THRUST BLOCK DESIGN - STANDARD THRUST BLOCK TYPE 1
THRUST1.xls
Spreadsheet by:
Calculations by:
Project: Standard Thrust Block Checked by:
WUD Anchor Block Type 1 for B Date:
Lf=200 min
Block
Pipe cover cover
45 A
d Hb/2
J OD
d Hb/2
X
SECTION X-X
PLAN
CASE PARAMETERS
Diameter DNmm 100.0 mm =INDEX(Data,case,1)
DN 0.1 m =DNmm/1000
Bend angle DegB 0 deg =INDEX(Data,case,2)
half angle AngB 0 rad =DEGB/2*PI()/180
Test pressure Pt 9 bar =INDEX(Data,case,3)
Cover to Pipe Cover 900 mm =INDEX(Data,case,4)
CALCULATIONS
Angle of soil friction AngS 0.5236 rad =SDeg*PI()/180
Active Ka 0.333 =TAN(PI()/4-AngS/2)^2
Passive Kp 3.000 =TAN(PI()/4+AngS/2)^2
Net Kn 2.667 =Kp-Ka
Base friction Kb 0.577 =TAN(AngS)
Pipe material mat 2 DI/GRP
Plastic/Steel ODst 0.1000 m =DN
DI/GRP ODdi 0.1188 m =DN*1.0329+0.0155
AC-12 ODac12 0.1131 m =DN*1.084+0.0047
AC-18 ODac18 0.1155 m =DN*1.131+0.0024
AC-24 ODac24 0.1200 m =DN*1.2
Outside Diameter OD 0.1188 m =CHOOSE(mat,ODst,ODdi,ODac12,ODac18,ODac24)
Cross sectional area XAP 0.01108 m2 =PI()*OD^2/4
Design thrust Td 9.97 kN =XAP*PT*100*IF(AngB<>0,2*SIN(AngB),1)
Dimension A(empirical) Term 1 TAT1 0.38268 m =2*2*DN*SIN(AngB)
Term 2 TAT2 0.13858 m =0.15*COS(AngB)
Sum As 0.52127 m =TAT1+TAT2
Round off to nearest 50 A 0.319 m =IF(AngB<>0,ROUND(As*2,1)/2,OD+0.2)
Effective Soil Density Ys 17.50 kN/m3 =IF(SB=0,Ysd,Yss)
Effective concrete Density Yc 23.00 kN/m3 =IF(SB=0,Ycd,Ycd-9.8)
Depth to pipe centre Ds 0.959 m =Cover/1000+OD/2
Block height Hb 0.51879 m =OD+2*d
Volume of Concrete
Vol concrete Volf1 0.06225 m3 =B*Hb*Lf
Volb1 0.03351 m3 =(B^2-A^2)*Hb/4