Professional Documents
Culture Documents
User manual
Copyright
© 2013 Thrane & Thrane A/S. All rights reserved.
Record of revisions
Rev Description Release Date Initials
B Cobham rebranding December 2013 CMA
PART I
Contents
PART I H1252A / TT-3608A-220
H1252B / TT-3608A
1 General information ....................................................................................................................2
2 Installation ........................................................................................................................................3
2.1 Mounting possibilities ..........................................................................................................3
2 Maintenance/modification .....................................................................................................7
2.1 Disassembling to remove the mains transformer ...................................................7
2.2 Disassembling and mounting of the ON-OFF switch ............................................8
2.3 Mounting the DC power supply and reassembling ..............................................8
2.3.1 Mounting of the DC power supply ................................................................................9
2.3.2 Modification of the printer main control board ......................................................9
2.3.3 Reassembling of the printer ........................................................................................... 10
2.4 Electrical connections ....................................................................................................... 11
3 Service ...............................................................................................................................................12
3.1 Printer selftest ....................................................................................................................... 12
3.2 Module check of the DC power supply .................................................................... 12
3.3 Check after repair ................................................................................................................ 12
0627
1
PART 1
1 General information
H1252A/TT-3608A-220 Hardcopy printer is an OKI MICROLINE 182/280 printer for
220/240V AC operation.
The printer is as standard delivered with a Roll Paper Stand, other paper types can also
be used, please refer to the OKI manual for detailed information.
The printer is as standard delivered with the mounting kit H1250, it can also be mounted
on the H2192 GMDSS Console using the mounting plate which is delivered together
with the H2192 GMDSS Console.
Paper roll, Power cable and Centronics cable are supplied with the Printer.
501279 501274
501278
2 0627
PART I
2 Installation
2.1 Mounting possibilities
Mounting kit H1250
240 mm
280 mm 371 mm
28709
Drilling plan
4 pcs ø6 mm
371 mm
290 mm
300 mm
341 mm
28711
0627
3
PART 1
240 mm
442 mm 325 mm
28699
Drilling plan
256 mm
2 pcs 4 mm
118.5 mm
428 mm
442 mm
28710
4 0627
PART II
37
1 mm
29
0m
m
Washers, 4 pieces M4
0 mm
30 m
Screws, 3 pieces M4 x 20 1m
34
28641A
25
6m
m
11
8.5
mm
m
8m
42 m
2m
44
Washers, 2 pieces M4
Screws, 3 pieces M4 x 20
28697
0627
5
PART II
1 General information
1.1 Introduction
This section gives you all the necessary informations to maintaine the DC power sup-
ply module. It also specify how to modify the printer to operate on DC supply instead
of AC supply.
Blockdiagram
PWM
CONTROL
CIRCUIT
6 0627
PART II
2 Maintenance/modification
This section is intended for use when modifying the printer to operate from DC supply
instead of 220V AC supply.
Remove the top cover by lifting up the front and pushing it backward.
Remove the transformer output cable from the printer Main Control Board.
Remove the ground strap screw, but keep it for later use.
Remove the two screws, that fix the transformer, but keep them for later use.
Remove the transformer assembly with power PCB and AC cord receptable by lifting
upwards.
Remove the 220V~ label located at the panel cut out for the AC cord receptable.
5 4
28560
0627
7
PART II
Remove the filter and switch board from the transformer by pulling it off.
Solder the switch to the two loose wires on the DC power supply module. Then twist
the wires to the switch to suppress noise.
Ground connection is
mounted under the
mounting frame
The mounting frame is
fixed with the two
screws from the
mains transformer
28556
8 0627
PART II
28557
If the printer is equipt with a DC power supply module from ECI, module no. 628471 it
is not recommended to short circuit the diode D28 (D10) on the printer main board.
0627
9
PART II
28479
10 0627
PART II
ON-OFF SWITCH
FROM MAINS
TRANSFORMER
OUTPUT CABLE
RED
GREEN
RED
BLACK BLACK
YELLOW/GREEN
DC INPUT CABLE
28558
0627
11
PART II
3 Service
Disconnect the dummy load from the 30V output and read the voltage to 39V ±2V.
12 0627
PART II
5 4
28560
0627
13
PART II
5 Circuit description
14 0627
PART II
0627
15
PART II
16
98-124013-THR-B
www.cobham.com/satcom