Professional Documents
Culture Documents
Contact Us
HO ME
ABO UT US
O UR S ERV ICES
5 TYPES OF SOIL TESTING FOR
P RO J ECT P HOTO S
CONSTRUCTION
TESTIMO N IAL S
Home/ Uncategorized / 5 Types of Soil Testing For Construction
N EW S
CO N TACT US
Search...
Recent Posts
CONSTRUCTION
Recent Comments
Soil testing is a very important part of building and road construction. In fact, no
construction project can proceed without first making sure the soil can support the
load. Thus, the purpose of soil testing for construction is to determine the suitability
Archives
of the soil for the type of construction to be done. The test is also done to determine
the presence of groundwater.
June 2020
carbide method, torsion balance method, Pycnometer method, sand bath method,
November 2019
radiation method, and alcohol method. The most common method is the oven-drying
method, which involves weighing the sample soil, drying it in an oven at a 110 October 2019
degrees Celsius (+/- 5 degrees), and weighing it again. The difference in the before
September 2019
and after weights is the weight of water in the soil.
August 2019
Specific Gravity Test
July 2019
The specific gravity of any substance is the ratio of density to the density of the
water. It is determined using one of several methods that include the density bottle June 2019
method, Pycnometer method, gas jar method, shrinkage limit method, and
measuring flask method. Of these, the most commonly used in soil analysis are the May 2019
The dry density of soil is the weight of soil particles in a given volume of a sample. Its
February 2019
value depends on the void ratio and the soil’s specific gravity. This value is used to
classify soil as dense, medium dense, or loose. The dry density test is done using one January 2019
of three methods: sand replacement, core cutter, or water displacement. Of these, the
December 2018
sand replacement and core cutter methods are the more widely used.
November 2018
Atterberg Limits Test
October 2018
This test is done on the fine-grained soil to measure its critical water content. There
are three limits that determine the properties of fine-grained soil under different September 2018
conditions: liquid limit, plastic limit, and shrinkage limit.
August 2018
a. In a liquid limit test, a device called a Casagrande’s liquid limit device, which
consists of a cup with a mechanism that moves up and down is used to determine July 2018
This test is conducted to find out the compaction characteristics of the soil. The soil December 2017
sample is air dried and then divided into four to six smaller samples. Their water
November 2017
content is adjusted by adding 3 percent to 5 percent water. The samples are then
placed in the Proctor compaction mold in three different layers. Each layer is then October 2017
given 25 blows from a standard 5.5-pound hammer. The samples are removed and
dried, and their dry density and water content are determined. A curve is then plotted September 2017
based on the entire set of results – with the density as a function of water content.
August 2017
This curve gives an accurate picture of the optimum water content needed to reach
the maximum dry density. July 2017
When taking samples, remember a soil test is only as good as the sample you take. June 2017
Therefore it is important to hire a professional highly experienced environmental
company to handle your soil testing for construction. One that specializes in
groundwater and soil testing, investigation, assessment, and remediation. All Categories
American Environmental is that company! We are located in Lake Hopatcong, NJ and
provide complete soil testing for construction services throughout northern NJ. Decontamination
Contact All American Environmental, NJ Environment
Oil Tanks
Soil / Groundwater
Uncategorized
Entries feed
Your comment here...
Comments feed
WordPress.org
Post Comment
HO ME
ABO UT US
O UR S ERV ICES
P RO J ECT P HOTO S
TESTIMO N IAL S
N EW S
CO N TACT US