Professional Documents
Culture Documents
99-01 Impreza Wiring Diagram PDF
99-01 Impreza Wiring Diagram PDF
1. General Description
1. General Description
A: WIRING DIAGRAM
The wiring diagram of each system is illustrated so
that you can understand the path through which
the electric current flows from the battery.
Sketches and codes are used in the diagrams.
They should read as follows:
I Each connector and its terminal position are
indicated by a sketch of the connector in a discon-
nected state which is viewed from the front.
G6M0193
I The number of poles or pins, presence of a lock, and pin number of each terminal are indicated in the
sketch of each connector. In the sketch, the highest pole number refers to the number of poles which the
connector has. For example, the sketch of the connector shown in figure indicates the connector has 9
poles.
Connector shown in wiring diagram
Connector used in vehicle
Sketch Symbol Number of poles
G6M0194 G6M0196
G6M0198
G6M0195 G6M0197
2
WIRING DIAGRAM [D1A0] 6-3
1. General Description
I When one set of connectors is viewed from the I The following color codes are used to indicate
front side, the pole numbers of one connector are the colors of the wires used.
symmetrical to those of the other. When these two
connectors are connected as a unit, the poles Color code Color
which have the same number are joined. L Blue
B Black
Y Yellow
G Green
R Red
W White
Br Brown
Lg Light green
Gr Gray
P Pink
Or Orange
G6M0199 Lb Light Blue
V Violet
I Electrical wiring harness:
SA Sealed (Inner)
The connectors are numbered along with the num-
SB Sealed (Outer)
ber of poles, external colors, and mating connec-
tions in the accompanying list.
I The sketch of each connector in the wiring dia-
gram usually shows the (A) side of the connector.
The relationship between the wire color, terminal
number and connector is described in figure.
NOTE:
A wire which runs in one direction from a connec-
tor terminal sometimes may have a different color
from that which runs in the other direction from that
terminal.
H6M0509A
G6M0201
I In wiring diagram, connectors which have no ter-
minal number refer to one-pole types. Sketches of
these connectors are omitted intentionally.
G6M0216
3
6-3 [D1A0] WIRING DIAGRAM
1. General Description
I The wire color code, which consists of two let- I Each unit is directly grounded to the body or
ters (or three letters including Br or Lg), indicates indirectly grounds through a harness ground termi-
the standard color (base color of the wire covering) nal. Different symbols are used in the wiring dia-
by its first letter and the stripe marking by its sec- gram to identify the two grounding systems.
ond letter.
G6M0203
G6M0202
I The ground points shown in the wiring diagram
I The table lists the nominal sectional areas and refer to the following:
allowable currents of the wires.
NOTE:
CAUTION:
All wiring harnesses are provided with a ground
I When replacing or repairing a wire, be sure
point which should be securely connected.
to use the same size and type of the wire which
was originally used.
NOTE:
I The allowable current in the table indicates the
tolerable amperage of each wire at an ambient
temperature of 40°C (104°F).
I The allowable current changes with ambient
temperature. Also, it changes if a bundle of more
than two wires is used.
Outside
No. of H6M0787A
Nominal sec- diameter of Allowable
strands/
tional area finished wir- current
strand diam-
mm2 ing Amps/40°C
eter
mm
0.3 7/0.26 1.8 7
0.5 7/0.32 2.2 (or 2.0) 12
0.75 30/0.18 2.6 (or 2.4) 16
0.85 11/0.32 2.4 (or 2.2) 16
1.25 16/0.32 2.7 (or 2.5) 21
2 26/0.32 3.1 (or 2.9) 28
3 41/0.32 3.8 (or 3.6) 38
5 65/0.32 4.6 (or 4.4) 51
8 50/0.45 5.5 67
4
WIRING DIAGRAM [D1A0] 6-3
1. General Description
I Relays are classified as normally-open or normally-closed. The normally-closed relay has one or more
contacts.
The wiring diagram shows the relay mode when the energizing circuit is OFF.
B6M0748
5
6-3 [D2A1] WIRING DIAGRAM
2. Basic Diagnostics Procedure
I Each connector number shown in the wiring dia- 2. Basic Diagnostics Procedure
gram corresponds to that in the wiring harness.
The location of each connector in the actual A: BASIC PROCEDURE
vehicle is determined by reading the first character
of the connector (for example, a “F” for F8, “i” for 1. GENERAL
i16, etc.) and the type of wiring harness. The most important purpose of diagnostics is to
The first character of each connector number determine which part is malfunctioning quickly, to
refers to the area or system of the vehicle. save time and labor.
Symbol Wiring harness and cord 2. IDENTIFICATION OF TROUBLE
F Front wiring harness SYMPTOM
B Bulkhead wiring harness
Determine what the problem is based on the symp-
Engine wiring harness,
E
Oxygen sensor cord
tom.
T Transmission cord 3. PROBABLE CAUSE OF TROUBLE
Door cord LH & RH,
D Look at the wiring diagram and check the system’s
Rear door cord LH & RH
i Instrument panel wiring harness
circuit. Then check the switch, relay, fuse, ground,
etc.
Rear wiring harness,
Rear defogger cord (Ground) 4. LOCATION AND REPAIR OF TROUBLE
Fuel tank cord,
R
Roof cord, 1) Using the diagnostics narrow down the causes.
Rear gate cord, 2) If necessary, use a voltmeter, ohmmeter, etc.
Rear gate lock adapter cord 3) Before replacing certain component parts
(switch, relay, etc.), check the power supply,
ground, for open wiring harness, poor connectors,
etc. If no problems are encountered, check the
component parts.
5. CONFIRMATION OF SYSTEM
OPERATION
After repairing, ensure that the system operates
properly.
B: INSPECTION
1. VOLTAGE MEASUREMENT
1) Using a voltmeter, connect the negative lead to
a good ground point or negative battery terminal
and the positive lead to the connector or compo-
nent terminal.
2) Contact the positive probe of the voltmeter on
connector (A).
The voltmeter will indicate a voltage.
3) Shift the positive probe to connector (B). The
voltmeter will indicate no voltage.
G6M0205
H6M0510A
6
WIRING DIAGRAM [D2B3] 6-3
2. Basic Diagnostics Procedure
4) With test set-up held as it is, turn switch ON. 3. HOW TO DETERMINE AN OPEN
The voltmeter will indicate a voltage and, at the CIRCUIT
same time, the light will come on.
1) Voltmeter Method:
5) The circuit is in good order. If a problem such
An open circuit is determined by measuring the
as a lamp failing to light occurs, use the proce-
voltage between respective connectors and
dures outlined above to track down the malfunc-
ground using a voltmeter, starting with the connec-
tion.
tor closest to the power supply. The power supply
2. CIRCUIT CONTINUITY CHECKS must be turned ON so that current flows in the cir-
cuit. If voltage is not present between a particular
1) Disconnect the battery terminal or connector so
connector and ground, the circuit between that
there is no voltage between the check points.
connector and the previous connector is open.
Contact the two leads of an ohmmeter to each of
the check points.
If the circuit has diodes, reverse the two leads and
check again.
2) Use an ohmmeter to check for diode continuity.
When contacting the negative lead to the diode
positive side and the positive lead to the negative
side, there should be continuity.
When contacting the two leads in reverse, there
should be no continuity.
G6M0208
2) Ohmmeter method:
Disconnect all connectors affected, and check con-
tinuity in the wiring between adjacent connectors.
When the ohmmeter indicates “infinite”, the wiring
is open.
G6M0207
B6M0749
7
6-3 [D2B4] WIRING DIAGRAM
3. Working Precautions
B: PRECAUTIONS IN TROUBLE
DIAGNOSIS AND REPAIR OF
ELECTRIC PARTS
G6M0210
1) The battery cable must be disconnected from
2) Ohmmeter method: the battery’s (−) terminal, and the ignition switch
Disconnect all affected connectors, and check con- must be set to the OFF position, unless otherwise
tinuity between each connector and ground. When required by the diagnostics.
ohmmeter indicates continuity between a particular 2) Securely fasten the wiring harness with clamps
connector and ground, that connector is shorted. and slips so that the harness does not interfere
with the body end parts or edges and bolts or
screws.
3) When installing parts, be careful not to catch
them on the wiring harness.
4) When disconnecting a connector, do not pull
the wires, but pull while holding the connector
body.
G6M0211
G6M0212
8
WIRING DIAGRAM [D3B0] 6-3
3. Working Precautions
5) Some connectors are provided with a lock. One 6) When checking continuity between connector
type of such a connector is disconnected by push- terminals, or measuring voltage across the termi-
ing the lock, and the other, by moving the lock up. nal and ground, always contact tester probe(s) on
In either type the lock shape must be identified terminals from the wiring connection side. If the
before attempting to disconnect the connector. probe is too thick to gain access to the terminal,
To connect, insert the connector until it snaps and use “mini” test leads.
confirm that it is tightly connected. To check water-proof connectors (which are not
accessible from the wiring side), contact test
probes on the terminal side being careful not to
bend or damage the terminals.
G6M0214
G6M0213
9
6-3 [D400] WIRING DIAGRAM
4. How to Use Wiring Diagram
H6M0796A
10
WIRING DIAGRAM [D4M0] 6-3
4. How to Use Wiring Diagram
B6M0750A
11
6-3 [D5A0] WIRING DIAGRAM
5. Wiring Diagram
5. Wiring Diagram
A: POWER SUPPLY ROUTING
GU01-05A
12
WIRING DIAGRAM [D5A0] 6-3
5. Wiring Diagram
GU01-05B
13
6-3 [D5A0] WIRING DIAGRAM
5. Wiring Diagram
14
WIRING DIAGRAM [D5A0] 6-3
5. Wiring Diagram
No. Load
ABS control module
AT shift lock control module
FB-30
Cruise control main switch
Cruise control module
15
6-3 [D5B0] WIRING DIAGRAM
5. Wiring Diagram
B: GROUND DISTRIBUTION
GU04-07A
16
WIRING DIAGRAM [D5B0] 6-3
5. Wiring Diagram
GU04-07B
17
6-3 [D5B0] WIRING DIAGRAM
5. Wiring Diagram
GU04-07C
18
WIRING DIAGRAM [D5C0] 6-3
5. Wiring Diagram
C: AIRBAG SYSTEM
GU86-07
19
6-3 [D5D0] WIRING DIAGRAM
5. Wiring Diagram
GU45-07A
20
WIRING DIAGRAM [D5D0] 6-3
5. Wiring Diagram
GU45-07B
21
6-3 [D5E0] WIRING DIAGRAM
5. Wiring Diagram
GU82-07A
22
WIRING DIAGRAM [D5E0] 6-3
5. Wiring Diagram
GU82-07B
23
6-3 [D5F0] WIRING DIAGRAM
5. Wiring Diagram
GU41-09A
24
WIRING DIAGRAM [D5F0] 6-3
5. Wiring Diagram
GU41-09B
25
6-3 [D5G0] WIRING DIAGRAM
5. Wiring Diagram
GU42-07
26
WIRING DIAGRAM [D5H0] 6-3
5. Wiring Diagram
H: AUDIO SYSTEM
GU76-06
27
6-3 [D5I0] WIRING DIAGRAM
5. Wiring Diagram
I: CHARGING SYSTEM
GU02-06
28
WIRING DIAGRAM [D5J0] 6-3
5. Wiring Diagram
J: COMBINATION METER
GU65-06
29
6-3 [D5K0] WIRING DIAGRAM
5. Wiring Diagram
GU71-08
30
WIRING DIAGRAM [D5L0] 6-3
5. Wiring Diagram
GU73-06
31
6-3 [D5M1] WIRING DIAGRAM
5. Wiring Diagram
GU10-16A
32
WIRING DIAGRAM [D5M1] 6-3
5. Wiring Diagram
GU10-16B
33
6-3 [D5M1] WIRING DIAGRAM
5. Wiring Diagram
GU10-16C
34
WIRING DIAGRAM [D5M1] 6-3
5. Wiring Diagram
GU10-16D
35
6-3 [D5M2] WIRING DIAGRAM
5. Wiring Diagram
GU10-17A
36
WIRING DIAGRAM [D5M2] 6-3
5. Wiring Diagram
GU10-17B
37
6-3 [D5M2] WIRING DIAGRAM
5. Wiring Diagram
GU10-17C
38
WIRING DIAGRAM [D5M2] 6-3
5. Wiring Diagram
GU10-17D
39
6-3 [D5N0] WIRING DIAGRAM
5. Wiring Diagram
GU61-08
40
WIRING DIAGRAM [D5O0] 6-3
5. Wiring Diagram
GU74-04
41
6-3 [D5P0] WIRING DIAGRAM
5. Wiring Diagram
GU77-01
42
WIRING DIAGRAM [D5Q0] 6-3
5. Wiring Diagram
GU29-06
43
6-3 [D5R0] WIRING DIAGRAM
5. Wiring Diagram
GU21-07A
44
WIRING DIAGRAM [D5R0] 6-3
5. Wiring Diagram
GU21-07B
45
6-3 [D5S1] WIRING DIAGRAM
5. Wiring Diagram
GU22-05
46
WIRING DIAGRAM [D5S2] 6-3
5. Wiring Diagram
GC22-01
47
6-3 [D5T1] WIRING DIAGRAM
5. Wiring Diagram
GU20-07
48
WIRING DIAGRAM [D5T2] 6-3
5. Wiring Diagram
GC20-08
49
6-3 [D5U0] WIRING DIAGRAM
5. Wiring Diagram
GU24-06
50
WIRING DIAGRAM [D5V0] 6-3
5. Wiring Diagram
GU25-05
51
6-3 [D5W0] WIRING DIAGRAM
5. Wiring Diagram
GU26-05
52
WIRING DIAGRAM [D5X0] 6-3
5. Wiring Diagram
GU82-01
53
6-3 [D5Y0] WIRING DIAGRAM
5. Wiring Diagram
GU66-07
54
WIRING DIAGRAM [D5Z0] 6-3
5. Wiring Diagram
GU60-06
55
6-3 [D5AA1] WIRING DIAGRAM
5. Wiring Diagram
GU70-08A
56
WIRING DIAGRAM [D5AA1] 6-3
5. Wiring Diagram
GU70-08B
57
6-3 [D5AA2] WIRING DIAGRAM
5. Wiring Diagram
2. COUPE MODEL
GU70-07
58
WIRING DIAGRAM [D5AB0] 6-3
5. Wiring Diagram
GU14-11
59
6-3 [D5AC0] WIRING DIAGRAM
5. Wiring Diagram
GU90-03
60
WIRING DIAGRAM [D5AD0] 6-3
5. Wiring Diagram
GU52-07
61
6-3 [D5AE0] WIRING DIAGRAM
5. Wiring Diagram
GU79-05
62
WIRING DIAGRAM [D5AF0] 6-3
5. Wiring Diagram
GU87-06
63
6-3 [D5AG0] WIRING DIAGRAM
5. Wiring Diagram
GU03-05
64
WIRING DIAGRAM [D5AH0] 6-3
5. Wiring Diagram
GU75-03
65
6-3 [D5AI0] WIRING DIAGRAM
5. Wiring Diagram
GU50-03
66
WIRING DIAGRAM [D5AJ0] 6-3
5. Wiring Diagram
GU51-04
67
6-3 [D5AJ0] WIRING DIAGRAM
5. Wiring Diagram
MEMO:
68
WIRING DIAGRAM [D6A0] 6-3
6. Electrical Wiring Harness and Ground Point
H6M0781A
(1) Front wiring harness (8) Rear wiring harness (15) Transmission cord
(2) Engine wiring harness (9) Rear defogger cord (Ground) (16) Rear gate cord
(3) Bulkhead wiring harness (10) Fuel tank cord (17) Rear gate lock adapter cord
(4) Instrument panel wiring harness (11) Rear door cord LH (18) Oxygen sensor cord
(5) Front door cord RH (12) Rear door adapter cord LH (19) Combination switch cord
(6) Rear door adapter cord RH (13) Front door cord LH (20) Trunk lid cord
(7) Rear door cord RH (14) Roof cord
69
6-3 [D6B0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
70
WIRING DIAGRAM [D6B0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0782A
71
6-3 [D6C0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
72
WIRING DIAGRAM [D6C0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0783A
73
6-3 [D6D0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
74
WIRING DIAGRAM [D6D0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0784A
75
6-3 [D6E1] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Connector Connecting to
No. Pole Color Area No. Name
T1 2 Gray D-1 B24
Bulkhead wiring harness (MT)
T2 2 Brown D-1 B25
T3 12 ★ D-3 B12
Bulkhead wiring harness (AT)
T4 20 Black D-3 B11
T7 12 ★ C-4 Inhibitor switch (AT)
★: Non-colored
76
WIRING DIAGRAM [D6E1] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0785A
77
6-3 [D6E2] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Connector Connecting to
No. Pole Color Area No. Name
T1 2 Gray D-1 B24
Bulkhead wiring harness (MT)
T2 2 Brown D-1 B25
T3 12 ★ D-3 B12
Bulkhead wiring harness (AT)
T4 20 Black D-3 B11
T7 12 ★ C-4 Inhibitor switch (AT)
★: Non-colored
78
WIRING DIAGRAM [D6E2] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0786A
79
6-3 [D6F0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
80
WIRING DIAGRAM [D6F0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0788A
81
6-3 [D6G0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
82
WIRING DIAGRAM [D6G0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0568A
83
6-3 [D6H0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
H: DOOR CORD
I List of Items
Connector Connecting to
No. Pole Color Area No. Name
D1 13 ★ C-3 B30 Bulkhead wiring harness
D2 2 ★ C-3 Front speaker LH
D3 2 Green C-3 Front power window motor LH
D5 6 ★ C-3 Remote control rearview mirror LH
16 ★ C-3 Power window main switch (Sedan and Wagon model)
D7
12 ★ C-3 Power window main switch (Coupe model)
D8 4 ★ C-3 Front door lock actuator LH
D11 13 ★ B-2 B101 Bulkhead wiring harness
D12 2 ★ B-2 Front speaker RH
D13 2 Green B-2 Front power window motor RH
D15 6 ★ B-2 Remote control rearview mirror RH
D17 5 ★ B-2 Front power window sub switch RH
D18 4 ★ B-2 Front door lock actuator RH
D21 8 ★ C-3 R11 Rear wiring harness
D23 2 ★ C-4 Rear door speaker LH
D24 2 Green C-4 Rear power window motor LH
D25 5 ★ B-4 Rear power window sub switch LH
D26 4 ★ B-4 Rear door lock actuator LH
D27 8 ★ B-2 R14 Rear wiring harness
D29 2 ★ B-3 Rear door speaker RH
D30 2 Green B-3 Rear power window motor RH
D31 5 ★ B-2 Rear power window sub switch RH
D32 4 ★ B-3 Rear door lock actuator RH
D50 9 ★ B-2 B113 Bulkhead wiring harness
D53 3 ★ B-2 B124 Bulkhead wiring harness
D54 8 ★ C-3 D55 Rear door cord LH
D55 8 ★ C-3 D54 Rear door adapter cord LH
D56 8 ★ B-2 D57 Rear door cord RH
D57 8 ★ B-2 D56 Rear door adapter cord RH
D62 8 ★ B-2 Door lock switch RH
★: Non-colored
84
WIRING DIAGRAM [D6H0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0538A
85
6-3 [D6I0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
86
WIRING DIAGRAM [D6I0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0569A
87
6-3 [D6J0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Connector Connecting to
No. Pole Color Area No. Name
D33 2 ★ C-3 R37
D34 4 ★ C-3 R38 Rear wiring harness
D35 4 ★ C-3 R39
D39 2 ★ B-2 High-mount stop light
D40 1 ★ B-3 Rear defogger (Power)
D43 4 ★ A-3 Rear wiper motor
D46 2 Black A-3 Rear gate latch switch
D47 4 ★ A-3 Rear gate lock actuator
D48 1 ★ A-3 Rear defogger (Ground)
D58 2 ★ A-3 D59 Rear gate lock adapter cord
D59 2 ★ A-3 D58 Rear gate cord
★: Non-colored
88
WIRING DIAGRAM [D6J0] 6-3
6. Electrical Wiring Harness and Ground Point
I Location
H6M0570A
89
6-3 WIRING DIAGRAM
MEMO:
90