Professional Documents
Culture Documents
B
Side
A JAPANESE
Side
B ENGLISH
Applicable standards 1.2 External Dimensions, Part Names, and Terminal Layout 2.1 Connection to the PLC
FX3U-4DA-ADP units made in June, 2005 or later comply with the EC Directive (EMC [5] [10] This section describes the connection method to the PLC (FX3U Series PLC is
Directive) and UL standards (UL, cUL). Further information can be found in the [3] [4] 24+ used for the following example).
following manual. 24- For installation method to other PLCs, refer to the respective PLC User's manual
[6]
→ FX3S Series Hardware Manual (Manual No. JY997D48301) Hardware Edition.
FX3U-4DA-ADP → FX3G Series Hardware Manual (Manual No. JY997D46001)
→ FX3GC Series Hardware Manual (Manual No. JY997D45201)
[2] [7] V1+ Procedure
1) Turn off the power.
→ FX3U Series Hardware Manual (Manual No. JY997D50301) I1+
106(4.18")
98(3.86")
90(3.55")
Regarding the standards that relate to the main unit, please refer to either the FX V2+ mounted directly using screws.
[1]
series product catalog or consult with your nearest Mitsubishi product provider. I2+ 2) Install an expansion board to the main unit.
Manual Number JY997D14001 For the expansion board installation procedure, refer to the following manual:
Attention COM2
Revision N → FX3U Series User's Manual - Hardware Edition
This product is designed for use in industrial applications. V3+ 3) Remove the special adapter connector cover
Date May 2018 I3+ on the expansion board (fig.A).
Caution for EC Directive
The analog special adapters have been found to be compliant to the European When connecting this product to another
S
/E
COM3
R
8M
-48M
-4
3U
4)
3U
FX
FX
standards in the aforesaid manual and directive. However, for the very best per- special adapter, please replace the
V4+ 'expansion board' in the above description
This manual describes the part names, dimensions, mounting, and specifications formance from what are in fact delicate measuring and controlled output device
of the product. Before use, read this manual and the manuals of all relevant Mitsubishi Electric would like to make the following points; 7(0.28") I4+ with a 'special adapter' and perform the RU
N
products fully to acquire proficiency in handling and operating the product. Make As analog devices are sensitive by nature, their use should be considered care- [9] COM4
B 3)
(0.62") (0.6") 4) Slide the special adapter slide lock
sure to learn all the product information, safety information, and precautions. fully. For users of proprietary cables (integral with sensors or actuators), these
[11] 17.6 (fig.B) of the main unit. 4)
Store this manual in a safe place so that it can be taken out and read whenever users should follow those manufacturers installation requirements.
(0.7") When connecting this product to another
necessary. Always forward it to the end user. Mitsubishi Electric recommend that shielded cables should be used. If NO other Special adapter A
Registration: EMC protection is provided, then users may experience temporary loss or connector cover special adapter, please replace the 'main
The company and product names described in this manual are registered accuracy between ±10 % in very heavy industrial areas. is removed unit' in the above description with a 'special
Weight: Approx. 0.1 kg (0.22 lbs) adapter' and perform the procedure as
trademarks or the trademarks of their respective companies. However, Mitsubishi Electric suggest that if adequate EMC precautions are fol-
lowed for the users complete control system, users should expect accuracy as indicated. (Please replace the following
Effective May 2018 B
specified in this manual. [1] DIN rail mounting groove (DIN rail: DIN46277) procedures similarly.)
Specifications are subject to change without notice. 5) Connect the
• Sensitive analog cable should not be laid in the same trunking or cable [2] Name plate
© 2005 Mitsubishi Electric Corporation special adapter B FX3U-48M
conduit as high voltage cabling. Where possible users should run analog [3] Special adapter slide lock:
C
S
Used to connect additional special adapters onto the left side of this special
***
3U
FX
P
O
main unit as
W
E
R
Safety Precautions (Read these precautions before use.) • Good cable shielding should be used. When terminating the shield at Earth adapter.
shown on the
6)
This manual classifies the safety precautions into two categories: - ensure that no earth loops are accidentally created. [4] Special adapter connector cover: right. RU
N
• When reading analog values, EMC accuracy can be improved out by Remove this cover to connect additional special adapters to the left side. 6) Slide back the
ST
OP
and . averaging the readings. This can be achieved either through functions on the [5] Direct mounting hole:2 holes of φ4.5 (0.18") (mounting screw: M4 screw) special adapter 5)
analog special adapters or through a users program. Not used when connecting to FX3GC/FX3UC Series PLC. 6)
slide lock (fig.B)
Indicates that incorrect handling may cause hazardous [6] POWER LED (green): of the main unit
conditions, resulting in death or severe injury. 1. Outline Lit while 24 V DC power is supplied properly to terminals '24+' and '24-'. to fix the special 5)
The FX3U-4DA-ADP special adapter for analog output (hereinafter called 4DA-ADP) is [7] Terminal block (European type): adapter (fig.C).
Indicates that incorrect handling may cause hazardous
a special adapter to add four analog output points. Connect the analog output voltage/current signal, and 24 V DC power supply.
conditions, resulting in medium or slight personal injury
or physical damage. 1.1 Incorporated Items [8] Special adapter connector: 5) B
Verify that the following product and items are included in the package: Used to connect this special adapter to PLC main unit or special adapter.
[9] DIN rail mounting hook
Depending on the circumstances, procedures indicated by may Product FX3U-4DA-ADP analog output special adapter Connection precautions
also cause severe injury. [10] Special adapter fixing hook
Connect all the high-speed I/O special adapters before connecting other
It is important to follow all precautions for personal safety. Accessories User’s manual (This manual) [11] Special adapter connector: special adapters when they are used in combination.
Used to connect communication or analog special adapters to the left side of the Do not connect a high-speed I/O special adapter on the left side of any
4DA-ADP.
Associated Manuals special adapters other than other high-speed I/O special adapters.
CRIMPFOX 6*1 DISPOSAL This manual confers no industrial property rights or any rights of any other kind,
Phoenix Contact Co., Ltd. AI 0.5-8WH PRECAUTIONS 20mA
(or CRIMPFOX 6T-F*2) 10V nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
Analog output
Output
*1 Old model name: CRIMPFOX ZA 3 occur as a result of using the contents noted in this manual.
environmentally safe recycling and disposal of your device. characteristics
*2 Old model name: CRIMPFOX UD 6
4mA Warranty
- Strand wire/single wire - Stick terminal with insulating sleeve TRANSPORTATION AND Exclusion of loss in opportunity and secondary loss from warranty liability
0 4000 4080 0 4000 4080
Insulation sleeve Contact area STORAGE PRECAUTIONS Digital input Digital input Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to:
(Crimp area) (1) Damages caused by any cause found not to be the responsibility of Mitsubishi.
• The product is a precision instrument. During transportation, avoid impacts larger
• The photocoupler is adopted to insulate the analog output area (2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products.
than those specified in the general specifications by using dedicated packaging
from the PLC. (3) Special damages and secondary damages whether foreseeable or not, compensation for
9mm 8mm boxes and shock-absorbing palettes. Insulation
(0.35") (0.31") • The DC/DC converter is adopted to insulate the power supply accidents, and compensation for damages to products other than Mitsubishi products.
Failure to do so may cause failures in the product. method
line from the analog output area. (4) Replacement by the user, maintenance of on-site equipment, start-up test run
After transportation, verify operation of the product and check for damage of the
2.6mm(0.1") 14mm(0.55") • Channels are not insulated from each other. and other tasks.
mounting part, etc.
When using a stick terminal with insulating sleeve, choose a wire with proper Occupied 0 point (This number is not related to the maximum number of
cable sheath referring to the above outside dimensions, or otherwise, the wire
4.1 Applicable PLC points input/output points of the PLC.) For safe use
cannot be inserted easily. Model name Applicability
The tightening torque must be 0.22 to 0.25 N•m. Do not tighten terminal • This product has been manufactured as a general-purpose part for general
screws with a torque outside the above-mentioned range. Failure to do so may FX3S Series PLC Ver. 1.00 or later (from first production) industries, and has not been designed or manufactured to be incorporated in
cause equipment failures or malfunctions. a device or system used in purposes related to human life.
FX3G Series PLC Ver. 1.00 or later (from first production) • Before using the product for special purposes such as nuclear power, electric
3.2 Power Supply Wiring FX3GC Series PLC Ver. 1.40 or later (from first production) power, aerospace, medicine or passenger movement vehicles, consult with
For the power supply wiring, refer to the following manual. Mitsubishi Electric.
→ FX3S/FX3G/FX3GC/FX3U/FX3UC Series User’s Manual - Analog Control FX3U Series PLC Ver. 2.20 or later (from first production) • This product has been manufactured under strict quality control. However
Edition Ver. 1.20 or later (from the production manufactured in May, when installing the product where major accidents or losses could occur if the
FX3UC Series PLC product fails, install appropriate backup or failsafe functions in the system.
2004 with SER No. 45****)
The version number can be checked by monitoring D8001/D8101 as the last three
digits indicate it.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
JY997D14001N Side
B
Side
A JAPANESE
Side
B ENGLISH
Applicable standards 1.2 External Dimensions, Part Names, and Terminal Layout 2.1 Connection to the PLC
FX3U-4DA-ADP units made in June, 2005 or later comply with the EC Directive (EMC [5] [10] This section describes the connection method to the PLC (FX3U Series PLC is
Directive) and UL standards (UL, cUL). Further information can be found in the [3] [4] 24+ used for the following example).
following manual. 24- For installation method to other PLCs, refer to the respective PLC User's manual
[6]
→ FX3S Series Hardware Manual (Manual No. JY997D48301) Hardware Edition.
FX3U-4DA-ADP → FX3G Series Hardware Manual (Manual No. JY997D46001)
→ FX3GC Series Hardware Manual (Manual No. JY997D45201)
[2] [7] V1+ Procedure
1) Turn off the power.
→ FX3U Series Hardware Manual (Manual No. JY997D50301) I1+
106(4.18")
98(3.86")
90(3.55")
Regarding the standards that relate to the main unit, please refer to either the FX V2+ mounted directly using screws.
[1]
series product catalog or consult with your nearest Mitsubishi product provider. I2+ 2) Install an expansion board to the main unit.
Manual Number JY997D14001 For the expansion board installation procedure, refer to the following manual:
Attention COM2
Revision N → FX3U Series User's Manual - Hardware Edition
This product is designed for use in industrial applications. V3+ 3) Remove the special adapter connector cover
Date May 2018 I3+ on the expansion board (fig.A).
Caution for EC Directive
The analog special adapters have been found to be compliant to the European When connecting this product to another
S
/E
COM3
R
8M
-48M
-4
3U
4)
3U
FX
FX
standards in the aforesaid manual and directive. However, for the very best per- special adapter, please replace the
V4+ 'expansion board' in the above description
This manual describes the part names, dimensions, mounting, and specifications formance from what are in fact delicate measuring and controlled output device
of the product. Before use, read this manual and the manuals of all relevant Mitsubishi Electric would like to make the following points; 7(0.28") I4+ with a 'special adapter' and perform the RU
N
products fully to acquire proficiency in handling and operating the product. Make As analog devices are sensitive by nature, their use should be considered care- [9] COM4
B 3)
(0.62") (0.6") 4) Slide the special adapter slide lock
sure to learn all the product information, safety information, and precautions. fully. For users of proprietary cables (integral with sensors or actuators), these
[11] 17.6 (fig.B) of the main unit. 4)
Store this manual in a safe place so that it can be taken out and read whenever users should follow those manufacturers installation requirements.
(0.7") When connecting this product to another
necessary. Always forward it to the end user. Mitsubishi Electric recommend that shielded cables should be used. If NO other Special adapter A
Registration: EMC protection is provided, then users may experience temporary loss or connector cover special adapter, please replace the 'main
The company and product names described in this manual are registered accuracy between ±10 % in very heavy industrial areas. is removed unit' in the above description with a 'special
Weight: Approx. 0.1 kg (0.22 lbs) adapter' and perform the procedure as
trademarks or the trademarks of their respective companies. However, Mitsubishi Electric suggest that if adequate EMC precautions are fol-
lowed for the users complete control system, users should expect accuracy as indicated. (Please replace the following
Effective May 2018 B
specified in this manual. [1] DIN rail mounting groove (DIN rail: DIN46277) procedures similarly.)
Specifications are subject to change without notice. 5) Connect the
• Sensitive analog cable should not be laid in the same trunking or cable [2] Name plate
© 2005 Mitsubishi Electric Corporation special adapter B FX3U-48M
conduit as high voltage cabling. Where possible users should run analog [3] Special adapter slide lock:
C
S
Used to connect additional special adapters onto the left side of this special
***
3U
FX
P
O
main unit as
W
E
R
Safety Precautions (Read these precautions before use.) • Good cable shielding should be used. When terminating the shield at Earth adapter.
shown on the
6)
This manual classifies the safety precautions into two categories: - ensure that no earth loops are accidentally created. [4] Special adapter connector cover: right. RU
N
• When reading analog values, EMC accuracy can be improved out by Remove this cover to connect additional special adapters to the left side. 6) Slide back the
ST
OP
and . averaging the readings. This can be achieved either through functions on the [5] Direct mounting hole:2 holes of φ4.5 (0.18") (mounting screw: M4 screw) special adapter 5)
analog special adapters or through a users program. Not used when connecting to FX3GC/FX3UC Series PLC. 6)
slide lock (fig.B)
Indicates that incorrect handling may cause hazardous [6] POWER LED (green): of the main unit
conditions, resulting in death or severe injury. 1. Outline Lit while 24 V DC power is supplied properly to terminals '24+' and '24-'. to fix the special 5)
The FX3U-4DA-ADP special adapter for analog output (hereinafter called 4DA-ADP) is [7] Terminal block (European type): adapter (fig.C).
Indicates that incorrect handling may cause hazardous
a special adapter to add four analog output points. Connect the analog output voltage/current signal, and 24 V DC power supply.
conditions, resulting in medium or slight personal injury
or physical damage. 1.1 Incorporated Items [8] Special adapter connector: 5) B
Verify that the following product and items are included in the package: Used to connect this special adapter to PLC main unit or special adapter.
[9] DIN rail mounting hook
Depending on the circumstances, procedures indicated by may Product FX3U-4DA-ADP analog output special adapter Connection precautions
also cause severe injury. [10] Special adapter fixing hook
Connect all the high-speed I/O special adapters before connecting other
It is important to follow all precautions for personal safety. Accessories User’s manual (This manual) [11] Special adapter connector: special adapters when they are used in combination.
Used to connect communication or analog special adapters to the left side of the Do not connect a high-speed I/O special adapter on the left side of any
4DA-ADP.
Associated Manuals special adapters other than other high-speed I/O special adapters.
CRIMPFOX 6*1 DISPOSAL This manual confers no industrial property rights or any rights of any other kind,
Phoenix Contact Co., Ltd. AI 0.5-8WH PRECAUTIONS 20mA
(or CRIMPFOX 6T-F*2) 10V nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
Analog output
Output
*1 Old model name: CRIMPFOX ZA 3 occur as a result of using the contents noted in this manual.
environmentally safe recycling and disposal of your device. characteristics
*2 Old model name: CRIMPFOX UD 6
4mA Warranty
- Strand wire/single wire - Stick terminal with insulating sleeve TRANSPORTATION AND Exclusion of loss in opportunity and secondary loss from warranty liability
0 4000 4080 0 4000 4080
Insulation sleeve Contact area STORAGE PRECAUTIONS Digital input Digital input Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to:
(Crimp area) (1) Damages caused by any cause found not to be the responsibility of Mitsubishi.
• The product is a precision instrument. During transportation, avoid impacts larger
• The photocoupler is adopted to insulate the analog output area (2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products.
than those specified in the general specifications by using dedicated packaging
from the PLC. (3) Special damages and secondary damages whether foreseeable or not, compensation for
9mm 8mm boxes and shock-absorbing palettes. Insulation
(0.35") (0.31") • The DC/DC converter is adopted to insulate the power supply accidents, and compensation for damages to products other than Mitsubishi products.
Failure to do so may cause failures in the product. method
line from the analog output area. (4) Replacement by the user, maintenance of on-site equipment, start-up test run
After transportation, verify operation of the product and check for damage of the
2.6mm(0.1") 14mm(0.55") • Channels are not insulated from each other. and other tasks.
mounting part, etc.
When using a stick terminal with insulating sleeve, choose a wire with proper Occupied 0 point (This number is not related to the maximum number of
cable sheath referring to the above outside dimensions, or otherwise, the wire
4.1 Applicable PLC points input/output points of the PLC.) For safe use
cannot be inserted easily. Model name Applicability
The tightening torque must be 0.22 to 0.25 N•m. Do not tighten terminal • This product has been manufactured as a general-purpose part for general
screws with a torque outside the above-mentioned range. Failure to do so may FX3S Series PLC Ver. 1.00 or later (from first production) industries, and has not been designed or manufactured to be incorporated in
cause equipment failures or malfunctions. a device or system used in purposes related to human life.
FX3G Series PLC Ver. 1.00 or later (from first production) • Before using the product for special purposes such as nuclear power, electric
3.2 Power Supply Wiring FX3GC Series PLC Ver. 1.40 or later (from first production) power, aerospace, medicine or passenger movement vehicles, consult with
For the power supply wiring, refer to the following manual. Mitsubishi Electric.
→ FX3S/FX3G/FX3GC/FX3U/FX3UC Series User’s Manual - Analog Control FX3U Series PLC Ver. 2.20 or later (from first production) • This product has been manufactured under strict quality control. However
Edition Ver. 1.20 or later (from the production manufactured in May, when installing the product where major accidents or losses could occur if the
FX3UC Series PLC product fails, install appropriate backup or failsafe functions in the system.
2004 with SER No. 45****)
The version number can be checked by monitoring D8001/D8101 as the last three
digits indicate it.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
JY997D14001N Side
B
Side
A JAPANESE
Side
B ENGLISH
Applicable standards 1.2 External Dimensions, Part Names, and Terminal Layout 2.1 Connection to the PLC
FX3U-4DA-ADP units made in June, 2005 or later comply with the EC Directive (EMC [5] [10] This section describes the connection method to the PLC (FX3U Series PLC is
Directive) and UL standards (UL, cUL). Further information can be found in the [3] [4] 24+ used for the following example).
following manual. 24- For installation method to other PLCs, refer to the respective PLC User's manual
[6]
→ FX3S Series Hardware Manual (Manual No. JY997D48301) Hardware Edition.
FX3U-4DA-ADP → FX3G Series Hardware Manual (Manual No. JY997D46001)
→ FX3GC Series Hardware Manual (Manual No. JY997D45201)
[2] [7] V1+ Procedure
1) Turn off the power.
→ FX3U Series Hardware Manual (Manual No. JY997D50301) I1+
106(4.18")
98(3.86")
90(3.55")
Regarding the standards that relate to the main unit, please refer to either the FX V2+ mounted directly using screws.
[1]
series product catalog or consult with your nearest Mitsubishi product provider. I2+ 2) Install an expansion board to the main unit.
Manual Number JY997D14001 For the expansion board installation procedure, refer to the following manual:
Attention COM2
Revision N → FX3U Series User's Manual - Hardware Edition
This product is designed for use in industrial applications. V3+ 3) Remove the special adapter connector cover
Date May 2018 I3+ on the expansion board (fig.A).
Caution for EC Directive
The analog special adapters have been found to be compliant to the European When connecting this product to another
S
/E
COM3
R
8M
-48M
-4
3U
4)
3U
FX
FX
standards in the aforesaid manual and directive. However, for the very best per- special adapter, please replace the
V4+ 'expansion board' in the above description
This manual describes the part names, dimensions, mounting, and specifications formance from what are in fact delicate measuring and controlled output device
of the product. Before use, read this manual and the manuals of all relevant Mitsubishi Electric would like to make the following points; 7(0.28") I4+ with a 'special adapter' and perform the RU
N
products fully to acquire proficiency in handling and operating the product. Make As analog devices are sensitive by nature, their use should be considered care- [9] COM4
B 3)
(0.62") (0.6") 4) Slide the special adapter slide lock
sure to learn all the product information, safety information, and precautions. fully. For users of proprietary cables (integral with sensors or actuators), these
[11] 17.6 (fig.B) of the main unit. 4)
Store this manual in a safe place so that it can be taken out and read whenever users should follow those manufacturers installation requirements.
(0.7") When connecting this product to another
necessary. Always forward it to the end user. Mitsubishi Electric recommend that shielded cables should be used. If NO other Special adapter A
Registration: EMC protection is provided, then users may experience temporary loss or connector cover special adapter, please replace the 'main
The company and product names described in this manual are registered accuracy between ±10 % in very heavy industrial areas. is removed unit' in the above description with a 'special
Weight: Approx. 0.1 kg (0.22 lbs) adapter' and perform the procedure as
trademarks or the trademarks of their respective companies. However, Mitsubishi Electric suggest that if adequate EMC precautions are fol-
lowed for the users complete control system, users should expect accuracy as indicated. (Please replace the following
Effective May 2018 B
specified in this manual. [1] DIN rail mounting groove (DIN rail: DIN46277) procedures similarly.)
Specifications are subject to change without notice. 5) Connect the
• Sensitive analog cable should not be laid in the same trunking or cable [2] Name plate
© 2005 Mitsubishi Electric Corporation special adapter B FX3U-48M
conduit as high voltage cabling. Where possible users should run analog [3] Special adapter slide lock:
C
S
Used to connect additional special adapters onto the left side of this special
***
3U
FX
P
O
main unit as
W
E
R
Safety Precautions (Read these precautions before use.) • Good cable shielding should be used. When terminating the shield at Earth adapter.
shown on the
6)
This manual classifies the safety precautions into two categories: - ensure that no earth loops are accidentally created. [4] Special adapter connector cover: right. RU
N
• When reading analog values, EMC accuracy can be improved out by Remove this cover to connect additional special adapters to the left side. 6) Slide back the
ST
OP
and . averaging the readings. This can be achieved either through functions on the [5] Direct mounting hole:2 holes of φ4.5 (0.18") (mounting screw: M4 screw) special adapter 5)
analog special adapters or through a users program. Not used when connecting to FX3GC/FX3UC Series PLC. 6)
slide lock (fig.B)
Indicates that incorrect handling may cause hazardous [6] POWER LED (green): of the main unit
conditions, resulting in death or severe injury. 1. Outline Lit while 24 V DC power is supplied properly to terminals '24+' and '24-'. to fix the special 5)
The FX3U-4DA-ADP special adapter for analog output (hereinafter called 4DA-ADP) is [7] Terminal block (European type): adapter (fig.C).
Indicates that incorrect handling may cause hazardous
a special adapter to add four analog output points. Connect the analog output voltage/current signal, and 24 V DC power supply.
conditions, resulting in medium or slight personal injury
or physical damage. 1.1 Incorporated Items [8] Special adapter connector: 5) B
Verify that the following product and items are included in the package: Used to connect this special adapter to PLC main unit or special adapter.
[9] DIN rail mounting hook
Depending on the circumstances, procedures indicated by may Product FX3U-4DA-ADP analog output special adapter Connection precautions
also cause severe injury. [10] Special adapter fixing hook
Connect all the high-speed I/O special adapters before connecting other
It is important to follow all precautions for personal safety. Accessories User’s manual (This manual) [11] Special adapter connector: special adapters when they are used in combination.
Used to connect communication or analog special adapters to the left side of the Do not connect a high-speed I/O special adapter on the left side of any
4DA-ADP.
Associated Manuals special adapters other than other high-speed I/O special adapters.
CRIMPFOX 6*1 DISPOSAL This manual confers no industrial property rights or any rights of any other kind,
Phoenix Contact Co., Ltd. AI 0.5-8WH PRECAUTIONS 20mA
(or CRIMPFOX 6T-F*2) 10V nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
Analog output
Output
*1 Old model name: CRIMPFOX ZA 3 occur as a result of using the contents noted in this manual.
environmentally safe recycling and disposal of your device. characteristics
*2 Old model name: CRIMPFOX UD 6
4mA Warranty
- Strand wire/single wire - Stick terminal with insulating sleeve TRANSPORTATION AND Exclusion of loss in opportunity and secondary loss from warranty liability
0 4000 4080 0 4000 4080
Insulation sleeve Contact area STORAGE PRECAUTIONS Digital input Digital input Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to:
(Crimp area) (1) Damages caused by any cause found not to be the responsibility of Mitsubishi.
• The product is a precision instrument. During transportation, avoid impacts larger
• The photocoupler is adopted to insulate the analog output area (2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products.
than those specified in the general specifications by using dedicated packaging
from the PLC. (3) Special damages and secondary damages whether foreseeable or not, compensation for
9mm 8mm boxes and shock-absorbing palettes. Insulation
(0.35") (0.31") • The DC/DC converter is adopted to insulate the power supply accidents, and compensation for damages to products other than Mitsubishi products.
Failure to do so may cause failures in the product. method
line from the analog output area. (4) Replacement by the user, maintenance of on-site equipment, start-up test run
After transportation, verify operation of the product and check for damage of the
2.6mm(0.1") 14mm(0.55") • Channels are not insulated from each other. and other tasks.
mounting part, etc.
When using a stick terminal with insulating sleeve, choose a wire with proper Occupied 0 point (This number is not related to the maximum number of
cable sheath referring to the above outside dimensions, or otherwise, the wire
4.1 Applicable PLC points input/output points of the PLC.) For safe use
cannot be inserted easily. Model name Applicability
The tightening torque must be 0.22 to 0.25 N•m. Do not tighten terminal • This product has been manufactured as a general-purpose part for general
screws with a torque outside the above-mentioned range. Failure to do so may FX3S Series PLC Ver. 1.00 or later (from first production) industries, and has not been designed or manufactured to be incorporated in
cause equipment failures or malfunctions. a device or system used in purposes related to human life.
FX3G Series PLC Ver. 1.00 or later (from first production) • Before using the product for special purposes such as nuclear power, electric
3.2 Power Supply Wiring FX3GC Series PLC Ver. 1.40 or later (from first production) power, aerospace, medicine or passenger movement vehicles, consult with
For the power supply wiring, refer to the following manual. Mitsubishi Electric.
→ FX3S/FX3G/FX3GC/FX3U/FX3UC Series User’s Manual - Analog Control FX3U Series PLC Ver. 2.20 or later (from first production) • This product has been manufactured under strict quality control. However
Edition Ver. 1.20 or later (from the production manufactured in May, when installing the product where major accidents or losses could occur if the
FX3UC Series PLC product fails, install appropriate backup or failsafe functions in the system.
2004 with SER No. 45****)
The version number can be checked by monitoring D8001/D8101 as the last three
digits indicate it.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN