Professional Documents
Culture Documents
Alternator: Shutdown SIS Previous Screen
Alternator: Shutdown SIS Previous Screen
Page 1 of 10
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B/950E WHEEL LOADER 22Z
Configuration: 950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE
Alternator
SMCS - 1405-015; 1405-016
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 2 of 10
Alternator
(1) Pulley nut. (2) Fan. (3) Shield. (5) Drive frame. (6) Rear frame. (7) Rotor. (8) Bearing. (9) Screws - three. (10)
Retainer. (11) Screw. (12) Screws - four. (13) Plate. (14) Nuts - three. (15) Screw. (17) R terminal. (18) Strap. (19) Screws
- two. (20) Regulator. (21) Diode trio. (22) Screw. (23) Nut. (24) Strap. (26) Nut. (27) BAT terminal. (28) Strap. (29)
Screw. (31) Capacitor. (32) Screw. (33) Rectifier. (35) Stator. (36) Screws - four. (37) Field coil. (38) Bearing. (39)
Collar. (40) Collar.
Disassemble Alternator
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 3 of 10
NOTE: The disassembly and assembly procedures are of the 3T6352 alternator. Other 20-SI
alternators are similar.
Start by:
a. remove alternator.
3. Remove shield (3). Remove four bolts (4) and separate drive frame (5) from rear frame (6).
4. Attach puller as shown. Remove drive frame (5) from rotor (7). As drive frame (5) is separated
from rotor (7), collars (40) and (39) are no longer secured. Remove collars (40) and (39).
5. Remove three screws (9) and retainer (10). Use a puller to remove bearing (8) from drive frame (5).
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 4 of 10
6. Remove screw (11) at the GND terminal. Remove four screws (12) and plate (13) from rear frame
(6).
7. Remove three nuts (14) and disconnect the stator leads from rectifier (33).
9. Loosen nut (16). Remove R terminal (17) and strap (18) together.
10. Remove two screws (19) at the field oil terminals of regulator (20). Remove diode trio (21).
11. Remove screw (22) at the ground terminal of rectifier (33). Remove nut (23) at the ground
terminal of regulator (20). Remove strap (24).
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 5 of 10
12. Remove insulator (25) and loosen nut (26). Remove BAT terminal (27) and strap (28) together.
16. Loosen grommet (34) and remove stator (35) from rear frame (6).
17. Remove four screws (36) and remove field coil (37) from rear frame (6).
Assemble Alternator
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 6 of 10
NOTICE
1. Install bearing (8) in drive frame (5). Install retainer (10) with three screws (9).
2. Place collar (39) on shaft of rotor (7). Insert the shaft of rotor (7) through bearing (8) in drive frame
(5).
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 7 of 10
4. Install spacers and nut as shown. Fully seat the shaft of rotor (7) in bearing (8).
5. If removed, install bearing (38) in rear frame (6). Use the 1P510 Drive Group.
6. Place field coil (37) in rear frame (6). Install and tighten four screws (36).
7. Place stator (35) in rear frame (6). Position grommet (34) in indentation (41).
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 8 of 10
8. Place rectifier (33) in rear frame (6). Install and tighten screw (32).
9. Place capacitor (31) in rear frame (6). Install and tighten screw (30).
10. Place regulator (20) in rear frame (6). Install and tighten screw (29).
11. Place BAT terminal (27) and strap (28) in rear frame (6). Make sure insulators (42) are properly
positioned.
12. Install insulator (25) through the lead of capacitor (31) and strap (28).
14. Place diode trio (21) on rectifier (33) and regulator (20).
15. Place R terminal (17) and strap (18) in rear frame (6). Make sure insulators (43) are properly
positioned. Tighten nut (16).
NOTE: For correct operation, there is NO continuity between screw (15) and strap (28); or between
nut (26) and rear frame (6); or between R term (17) and rear frame (6).
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(S... Page 9 of 10
16. Make sure the insulators are installed on screws (19). Place the field coil leads on screws (19).
Install and tighten two screws (19).
17. Place strap (24) on rectifier (33) and regulator (20). Install and tighten screw (22) and nut (23).
NOTE: For correct operation, there is NO continuity between screws (19) and the respective field
coil lead.
18. Place the stator leads on the terminals of rectifier (33). Install and tighten three nuts (14) on the
terminals of rectifier (33).
19. Position plate (13) on rear frame (6). Install and tighten four screws (12). Install screw (11) at the
GND terminal.
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25
950E WHEEL LOADER 22Z03189-UP (MACHINE) POWERED BY 3304 ENGINE(... Page 10 of 10
20. Join rear frame (6) and drive frame (5). Install four bolts (4) and tighten to 6.2 ± 0.6 N·m (55 ± 5
lb in).
23. Install the pulley nut and tighten to 100 ± 7 N·m (75 ± 5 lb ft).
End by:
a. install alternator.
Copyright 1993 - 2020 Caterpillar Inc. Tue Aug 25 11:49:22 UTC+0200 2020
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1:3000/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 2020/08/25