Professional Documents
Culture Documents
ST05L
STEP 4
P12X
P12X
P12X P12X
SS3X5 SS3X5
SF3X8
SF3X8
15
STEP 25
Attention! Cut upper leg of P12X
The deflected tips of Sway Bar high roll
should be directed downwards. centers setups.
re ove
SWB10...SWB12
Note:
SS3X3 SWB12 - two strips Note:
SWB11 - one strip Don t tighten SS3X3 Set Screws at this stage.
SWB10 - no strip
SS3X3
AT142
B63SS
B63SS AT142
SWB10...SWB12
P05
maller hole for
SB10 and SB11
Sway Bars.
STEP 25 FINISHED
REAR FRONT
16
STEP 26 9,8 mm
Servo rod or lon
servo l nk la out
P13-4 P13-4
AT14 AT14
Front right
Front left upper arm
upper arm AT14 Turnbuckle x9
AT25 Turnbuckle x2
AT25-44 Turnbuckle x2
P01 Ball Joint 1 x4
P02 Ball Joint 2 x4
P13-4 Ball End x18
AT14 AT14
P13-4 P13-4
AT14 AT14
P13-4 P13-4
Notes: The given rods and arms sizes are approximately for 4° front caster and 0° rear caster, 2° both front and rear
cambers, 3,0° rear toe-in and 1° front toe out angles. Use a setup station or angles gauge for further precise suspension
geometry setting. See our recommendations on page #23 for quick and easy suspension geometry change.
17
STEP 27 Note: Use the appropriate combination of
SB3X10
SH spacers for sufficient gap between
SB3X10
battery and P25 Cla ps.
SB3X10P25
AT12
P25 P25
BATTERY P25
SH0.5...SH1.0 SH0.5...SH1.75
AM15-3 P23
AM15-1 SH0.5...SH1.75
AM15-3
AM15-3
SF3X6
P23
SF3X6
P23
SH1.75 x2
SF3X10 x2 SH0.5 SH1.75 x2
SH0.5
SB3X8
SF3X10 x2
SB3X8
ST110 and ST105 Round Weights should e used for adjusting s ST110 and
of the final weight and the weight distribution of the car. ST105 ST110 or ST105
ST105
ST110
ST105 5g
ST110 10g Round Weight
ST110 Round Weight
18
STEP28
SB3X5 x2
SH0.5 x2
Servo (not included)
AM24-8
SB3X5
AT21ST-A
For lon servo l nk la out
SB3X5 SF3X5 x3
Note: Recommended length of the servo horn at the lon servo l nk la out 6 .
Recommended length of the servo horn at the hort servo l nk la out ~ .
Attention! Neutral servo arm position Short servo link layout 15mm servo horn
at lon servo l nk la out.
Long servo link layout Use th s hole o AM180 Cut two P13-4 and use
and SH0.5+SH1.75 s a ers SS3X12 as a turnbuckle.
19
OR06
STEP 9
OR06 Attention!
ke e
P14-1 b k e e ee
e e e e
SPR05 ~1 7m m
SB3X6 x2
SPR05
P14-2
OR06
P14-2
SH1.75
SH1.75 P14-5 OR06
SPR05
SPR05
P14-2
P15L P14-2
P14-1X
SB3X12
SB3X12 AM05-2
SB3X8
SB3X8
OR06 T55M
or
OR18 dependin of the
spur gear thickness
T55M
T55
OR06
Spur Gear +OR06
or
(not included) or OR18 SH0.5 x2
OR18 dependin of the spur SB3X10 x2
ear thickness
STEP 31
FINAL ASSEMBLY
Install:
Speed controller (not included),
Receiver (not included),
Battery (not included)
Wheels (not included)
20
Optional parts and sets
AT22M Rear Body Holder HRB Horizontal Rear Bodypost Set
Use the extra clipped
P14-2 bars for additional P14-2
support of body s tail.
SB3X6 x2
P14-2
C05-H SH0.5 x2
M126
A 22M
SB3X10
SB3X8
clipped P14-2
SB3X6
SB3X6 x2
C26
SH1.75 x
AM105 or AM105
AT139
SB3X12 SB3X10
SF3X5
Fan (not included)
BW7, BW8, BW10 Weights AM111 Belt Anti Skip BC1 Battery Clamp Set
SB3X5 AM12 , AT144
SB3X6
B73SS
BW 0 P21
SB 5X8
AT26 or AT144
SB 5X8
SB3X8 AM111
SH0.5...SH1,75
SS3X12
BW8 SB 5X8
SB 5X6
SB 5X8
BW7 AM111
SB3X8
AM12
AT139 Fan Holder (optional)
21