Professional Documents
Culture Documents
141G
20CE
30CE
20CF (With U.T.T)
30CF (With U.T.T)
SINGER and the Cameo "S" Design are exclusive trademarks of The Singer Company Limited S.à r.l. or its Affiliates.
©2018 The Singer Company Limited S.à r.l. or its Affiliates. All rights reserved.
Contents
1 Safety Instructions 1
1.1 Important Safety Instructions 1
1.2 Safe Operation 2
2 Product Description and Machine Specification 3
2.1 Product Description 3
2.2 Machine Specification 4
2.3 Motor specifications 4
3 Setup and Adjustment Instructions 5
3.1 Table Cut-Out Drawing 5
3.2 Oil Reservoir Installation 6
3.3 Lubrication 7
3.4 Rotating Hook Oil Supply Adjustment 8
3.5 Needle Attachment 9
3.6 Machine Threading 9
3.7 Winding the Bobbin Thread 10
3.8 Bobbin Case Attachment 11
3.9 Stitch Length Adjustment 11
3.10 Thread Tension Adjustment 11
3.11 Thread Take-Up Spring Adjustment 12
3.12 Thread Take-Up Stroke Adjustment 12
3.13 Knee Lifter Height Adjustment 13
3.14 Presser Foot Lifter Adjustment 13
3.15 Presser Foot Pressure Adjustment 13
3.16 Pedal Adjustment 14
3.17 Pedal Operation 14
3.18 Needle to Rotating Hook Relation Adjustment 15
3.19 Thread Trimmer Adjustment 16
3.20 Movable and Fixed Knives Position 17
3.21 Height and Tilt of the Feed Dog 18
3.22 Feed Timing Adjustment 19
3.23 Function of One-Touch Switch 20
3.24 Connection of Foot Pedal Switch 20
Contents
4 Maintenance 21
4.1 Machine Head Cleaning 21
4.2 Lubrication 21
4.3 Safety Inspection 21
5 Trouble Shooting 22
6 Parts List 25
6.1 Frame and Micellaneous Cover Components 26
6.2 Arm Shaft and Thread Take-up Lever Components 28
Needle Bar, Upright Shaft and Rotating Hook Driving Shaft
6.3 30
Components
6.4 Presser Bar Components 32
6.5 Feed Mechanism Components 34
6.6 Thread Trimmer Components 38
6.7 Specific parts for 141G-30CE / CF 40
6.8 Lubrication Components 42
6.9 Oil Reservoir Components 44
6.10 Machine Accessories 46
Safety Instructions
1.1
Important
·Before running the machine, make
sure all relevant safety specifica-
tions are adequate to specifica-
·
should only be performed by
properly trained personnel.
tions and technical standards in
Safety your country.
·Maintenance and repair on elec-
Instructions tric equipment should only be
·The machine should not be run made by qualified personnel. If
without its safety devices. any electric device is damaged,
the machine should be immedi-
·Please don’t operate when envi- ately stopped.
When using the ronment temperature is above
machine, basic safety 45°C or below 0°C. ·Before starting the machine in full
procedures must running, a test must be conducted
·For your safety, goggles must be to assure that machine and opera-
be followed. Read used while running the machine. tor are able to perform the task.
with attention all
·Turn off or unplug the machine
·The machine should not be placed
instructions before when the following situationsarise: next to a sound source as an ultra-
using the machine.
·Passing the thread by the nee- sonic welding machine and other
When using it, dle or replacing the bobbin or equipment.
understand that looper.
·The machine should only be run
all basic safety ·Replacing the needle, presser with the proper electric cable and
instructions are foot, throat plate, feed dog and connectors, and also the adequate
not limited to the sliding plate. grounding.
following items. ·When the machine is in mainte- ·The machine should only be used
Read all instructions, nance. to sew materials as indicated in
its instructions manual, and indi-
take care of this ·When the operator is not run-
cations of use should be followed.
manual, and use it ning the machine.
Singer will not be held responsible
as reference when · for any damage caused by unau-
necessary. with the eyes or skin, washed the
thorized changes in the product.
surface with plenty oficy water
with a generous amount of cold
water. In case ofingestion, seek
medical help immediately.
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 1
1.2
Safe Operation
·To avoid the risk of electric shock,
do not open the motor wiring box
and do not touch the components
·If you machine is equipped with
a servomotor, it does not make
noises while being driven.To avoid
assembled inside the wiring box. a possible accident caused by an
unexpected start, be sure the ma-
·To avoid injuries do not run the
chineis turned o ff.
machine without the belt cover or
in case any other safety device is ·To avoid electrical shock, do not
removed. run the machine without proper
grounding.
·To avoid
gers, head and clothes far from ·To minimize the risk of accidents
wheel , belt and motor when the ma- or damage in electric components
chine is running . Nothin g should be caused by electric discharge turn
placed near those parts. the machine off before unplug-
ging it.
·To avoid injuries never put your
fingers next to the rotating hook ·Clean the machine periodically.
and the thread take-up lever cover
when the machine is running.
·To avoid possible injuries be care-
ful when putting down or lifting
the machine head.
·To avoid accident in case of a sud-
den start of the machine always
turn it off when laying it down, or
remove the belt cover and the belt.
CAUTION
·Carry the sewing machine with two ·Do not put a obstacle thing such as
persons as the shown in the figure. screwdriver at the location , where
Do not hold the handwheel. the sewing machine will be placed.
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 2
Product Description
and Machine Specification
2.1
Product
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 3
2.2
Machine
Specification
Height of Needle
Maximum Stitch
Singer Presser Foot Bar Hook Electric Needle Motor
Application Speed Length Lubrication
Model Hand / Knee Stroke Type Device Cat. Power
spm mm
[mm] mm
141G-20CEA 220V
Light to 1955-01
5,000 5.0 5.5 / 13.0 30.7
medium #14
141G-20CEB 110V
Automatic
Standard NU / ND (Oil pump)
141G-30CEA 220V
Medium to 1955-01
4,000 7.0 6.0 / 13.0 35.0
heavy #18
141G-30CEB 110V
141G-20CFA 220V
5.0 5.5 / 13.0 1955-01
Light to 5,000 30.7
#14
141G-20CFB medium 110V
UTT Automatic
Standard
(Oil pump)
141G-30CFA 220V
1955-01
Medium to 4,000 7.0 6.0 / 13.0 35.0
#18
141G-30CFB heavy
110V
2.3Motor
·Integrated direct drive servo motor with operation panel
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 4
Setup and Adjustment instructions
t = 1.0
Table Cut-Out Formica
Drawing Fig. I
Fig.II
Fig.II
Deep 30
Through
Through
Figure 1
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 5
3.2
The oil reservoir should rest on the portion of the table and other two
four corners of the machine table rubber cushion ‘2’ on the hinge side
groove. ‘B’.
Oil Reservoir Two rubber seats ‘1’ for supporting Then, the oil reservoir ‘3’ is placed.
Installation the head portion on the operator
side ‘A’ are fixed on the extended
Figure 2 Figure 3
Two hinges ‘1’ fit into the hole in ‘2’, before the machine head is
the machine bed, and the machine placed to the cushions ‘3’ on the
head fitted the table hinge’s rubber four corners of the table.
Figure 4 Figure 5
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 6
3.3
Before turning the machine on, When you operate the machine af-
fill oil reservoir ‘1’ with sewing ter lubrication, you will see splash-
machine oil up to ‘HIGH’ mark ‘A’ ing oil through oil sight window ‘2’
Lubrication (Figure 6). if the lubrication is adequate.
When the oil level lowers below Note that the amount of the splash-
Precaution ‘LOW’ mark ‘B’, refill the oil reser- ing oil is unrelated to the amount
When set-up a new voir with the specified oil. of the lubricating oil.
machine or a machine
after an extended
period of disuse, run
your machine at
3,000 - 3,500 rpm
A
for about 10 minutes
for the purpose
HIGH
of break-in. LOW
B
2
Figure 6
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 7
3.4
How to check the hook oil supply Sample showing the appropriate
amount of oil
Rotating Hook Unused machine should run idle The amount of oil can be adjusted
for 3 minutes (Moderate intermit- according to the different sewing
Oil Supply tent operation). process but it must be a suitable
Adjustment amount. Otherwise the hook will
The amount of oil confirmation generate heat or the sewing mate-
paper must be inserted in the state rial will be contaminated.
when the machine is running.
Use the amount of oil confirmation
The confirming time of the oil paper for three times to observe
amount is 5 seconds (check the the amount of oil. Adjust the screw
period of time with a watch). until the mark on the paper
unchanged.
1mm
Minimum
Bush
2mm
Maximun
Figure 7 Figure 8
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 8
3.5
Turn the hand wheel until the needle Insert the needle in the direction of
bar reaches the highest point of its the arrow until it will go no further.
stroke. Tighten the screw '2'.
Needle Loosen screw '2' and hold needle
Make sure the long groove 'C' of the
Attachment '1' with its indented part 'A' facing
needle is facing exactly to the left in
exactly to the right in direction 'B'.
direction 'D'.
Cautions
Choose a proper D B
needle size according
to the count of thread
A
and the type of sewing
C
material used.
The power supply 2
1
should be cut off
before attaching the
needle.
Figure 10
3.6
Machine
When threading the machine, the
needle bar should be at the high-
est point of its stroke.
Threading the machine in the order
shown below.
Leave thread approximately 4.0 cm
long in the needle.
Threading
1
2
7
3
4
10
8
6
11 9
5
Figure 11
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 9
3.7
1. The bobbin is pushed into the setscrew ‘4’ and move the bobbin
bobbin winder spindle ‘1’ until it winder adjusting plate ‘5’ to the
will go no further. direction of ‘A’ (Decrease) or ‘B’
Winding the (increase). Then, tighten the
Bobbin Thread 2. Pass the bobbin thread pulled out setscrew ‘4’.
from the spool rested out the right
side of the thread stand following 6. In case that the bobbin thread is
Cautions not wound evenly on the bobbin,
the order as shown in the figure on
When winding the the left. Then, wind clockwise the loosen the nut ‘6’ and turn the
bobbin thread, start the end of the bobbin thread on the bobbin thread tension to adjust the
bobbin several times. (In case of the height of the thread tension disk ‘7’.
winding in the state
aluminum bobbin, after winding
that the thread • It is the standard that the center of
clockwise the end of the bobbin
between the bobbin thread, wind counterclockwise the the bobbin is as high as the center
and thread tension disk thread coming from the bobbin of the thread tension disk ‘7’.
'7' is tense. thread tension several times to • Move the position of the thread
winding the bobbin thread with tension disk ‘7’ to the direction of
When winding the ease.) ‘A’ as shown in the figure on the left
bobbin thread in the when the winding amount of the
3. Press the bobbin winder lever ‘2’
state that sewing is not bobbin thread on the lower part of
in the direction ‘A’ and start the
performed, remove the sewing machine. The bobbin the bobbin is excessive and to the
needle thread from the rotates in the direction of ‘C’ and direction orb as shown in the figure
the bobbin thread is wound up. The on the left when the winding
thread path of thread
bobbin winder spindle ‘1’ automati- amount of the bobbin thread on the
take-up and remove upper part of the bobbin is exces-
cally as soon as the winding is
the bobbin from the sive.
finished.
hook.
4. Remove the bobbin and cut the • After the adjustment, tighten the
bobbin thread with the thread cut nut ‘6’.
retainer ‘3’. 7. To adjust the tension of the
5. To adjust the winding amount of bobbin winder, turn the thread
the bobbin thread, loosen the tension nut ‘8’.
8
B 1
2 A A
7
6
3
4
5
B
Figure 12
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 10
3.8
Bobbin Case
Fix the bobbin into bobbin case
with that the thread open end is
directed to the left as observed
A
from you. B
Attachment
Pass the thread through thread slit
‘A’, and pulls it in direction ‘B’. By
doing so, the thread will pass under
the tension spring and come out
from notch ‘B’. C
When pulling the thread ‘C’, the
bobbin should rotate in the direc- Figure 13
tion of the arrow.
3.9
Press revrese lever ‘1’, turn stitch dial
‘2’ direction of the arrow, and align
the desired number to marker dot A
Stitch Length ‘A’ on the machine arm.
Adjustment The indication of the dial is in milli- 2
meters.
When you want to decrease the 1
stitch length, press reverse lever ‘1’
while turn stitch dial ‘2’ in the direc-
tion of the arrow. Figure 14
3.10
Adjusting the needle thread tension Adjusting the bobbin thread tension
The tension nut ‘1’ can be adjusted Turn the screw ‘3’ clockwise (in
for the needle thread lengths after direction E), the bobbin thread
Thread Tension trimming. tension will be increased.
Adjustment
Turn the nut ‘1’ clockwise (in direc- Turn the screw ‘3’ counter-
tion A), the length of the needle clockwise (in direction F), the
thread will be shorter. bobbin thread tension will be
Turn the nut ‘1’ counter-clockwise decreased.
(in direction B), the length of the 1
needle thread will be longer.
Adjust the tension of needle thread A
B
by tension nut ‘2’ according to 2
different sewing conditions.
E F
Turn the nut ‘2’ clockwise (in direc- C
tion C), the needle thread tension D 3
will be increased.
Turn nut ‘2’ counter-clockwise (in
direction D), the needle thread
tension will be decreased.
Figure 15
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 11
3.11
The adjustment of the stroke of the Loosen setting screw '4' and turn
thread take-up spring the tension post '3'.
Loosen setting screw '2'. Turn the tension post '3' clockwise
Thread (in direction A), the pressure of the
Turn the thread tension post '3'
Take-up Spring clockwise (in direction A), the stroke spring will be increased.
Adjustment of the thread take-up spring will be Turn the tension post '3' counter
increased. clockwise (in direction B), the pres-
Turn the thread tension post '3' sure will be decreased.
counter-clockwise (in direction B), • Usually, the thread take-up spring
the stroke of the thread take-up '1' has been properly adjusted
spring will be in decreased. before leaving the factory.
Adjusting the pressure of the thread • Only when sewing special clothes
take-up spring '1' or using special thread is readjust-
Loosen setting screw '2' and take ment necessary.
out thread tension assembly.
A 3
B
4
2
3
Figure 16
3.12
When sewing for heavy weight
material, the thread guides '1' move
A B
to the left (in direction 'A' to
Thread increase the length of thread pulled
Take-up Stroke out by the thread take-up. 1
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 12
3.13
When using the knee lifter, the stan- Caution
dard height of the presser foot is
When the presser foot lift to over 10
10mm.
mm or more, be sure that the needle
Knee Lifter You can adjust the presser foot lift
bar ‘2’ in its lowest position does not
Height up to 13mm by turning the knee
hit the presser foot ‘3’.
lifter adjusting screw '1'.
Adjustment
2
3
Figure 18
3.14
Turn the presser foot lifter '1' in The presser foot will go back to its
direction 'A' to lift the presser foot. original position when the lifter is
The presser foot will go up about turned down in direction 'B'.
Presser Foot 5.5 mm and stop.
Lifter
Adjustment
1 1
A
B
Figure 19
3.15
Loosen the nut '2' and turn the
B A
presser spring regulator '1' clock-
wise (in direction A), the pressure
29-30 mm
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 13
3.16
Installing the connecting rod.
Move the pedal ‘3’ to the right or left
as illustrated by the arrows so that 2
Pedal the motor control lever ‘1’ and 1
2
Adjustment connecting rod ‘2’ are straightened.
Adjusting the pedal angle. 4
3.17
The pedal is operated in the follow-
ing.
Step ‘A’ position
Pedal
The machine runs at high sewing
Operation speed, when you further depress the
A
front part of the pedal.
Step ‘B’ position (Neutral)
The machine stops (with its needle B
Notes:
1) While the machine is on the auto reverse stitch, if the pedal put it to the neutral position,
the machine will stop after reverse stitches.
2) The machine will perform normal thread trimming even if you depress the back part of
the pedal immediately following high and low speed sewing.
3) The machine will completely perform thread trimming even if you reset the pedal to its
neutral position immediately after the machine started thread trimming function.
4) When the machine stops at the needle down, and if you intend to bring the needle up,
depress the back part of the pedal once.
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 14
3.18
Adjusting the height of the needle Adjusting the position of the rotat-
bar ing hook
Turn the hand wheel until the needle Loosen two rotating hook setscrews
Needle to bar '2' has been at the lowest point, and turn the hand wheel until the
Rotating loosen the setscrew '1'. line 'B' on needle bar align with the
Hook Relation The line 'A' on the needle bar '2' bottom end of needle bar lower
bushing '3'.
Adjustment align with the bottom end of needle
bar lower bushing '3', then securely After the above adjustments steps,
Precaution tighten the setscrew '1'. the rotating hook point '5' aligns
with the center of needle '4'(a) , and
If the clearance make sure the clearance between
is too small, the the needle and the rotating hook '5'
rotating hook points is 0.04~0.1 mm (b).
will wear out, and
too big, it will cause
the skip stitch.
When replacing the
rotating hook, it
should be using the
original one.
Center of needle
0.04~0.1mm
5
(a) (b)
Figure 23
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 15
3.19
Adjustment of the thread trimming Adjusting the position of the
cam position. (Figure 24) counter and the moving knives.
Turn the hand wheel until the needle (Figure 26)
Thread bar goes from the bottom up to 5.0 When the thread trimming shaft
Trimming mm. with the roller ‘3’ is at the highest
Adjustment The thread trimming solenoid ‘4’ is position in the thread trimming
pressed until the thread trimming cam‘1', the front tip of the counter
(For 141G-xxCFx knife ‘8’ and the edge of the
shaft with the roller ‘3’ touches to the
Only) concave of the thread trimming cam moving knife ‘7’ should be
‘1’. engaged by 0.2-0.5 mm.
8 7
7 8
Figure 24 0.2-0.5 mm
2 3
6
1
5
0.6-0.8 mm
Figure 25 Figure 26
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 16
3.20
Removing the fixed knife (Figure 27)
Tilt the machine head until it stops.
Movable Remove the screw ‘1’ and rotating 3 1
Figure 27
9
Removed the screw ‘5’ and the needle
plate ’6’.
Use the socket spanner ‘9’ to loosen 12 11
the nut ‘10', then turn the screw ’11’ 10
until desired pressure of fixed knife.
‘12’.
Figure 29
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 17
3.21
For adjusting of the height of the Adjust the height in accordance
feed dog. with the material to be used.
When the feed dog ’A’ is at its Loosen screw ‘2’ of crank ‘1’.
Height and highest position, the teeth should Move the feed bar up or down to
Tilt of the be above the top surface of the make a correct height.
Feed Dog throat plate ‘B’.
Securely tighten screw ‘2’.
Note
For preventing of See description below for height
1
uneven of the
material, raise the
fronts of the feed
dog. For preven- A
tion of puckering 2 B
of the material, 141G-20CE / -20CF 0.75 - 0.85 mm
lower the front of 141G-30CE / -30CF 1.15 - 1.25 mm
the feed dog.
Figure 30
Note For adjusting of the tilt of the feed To tilt the feed dog with its front up
dog. in order to prevent puckering,
Whenever the
feed dog tilt is The standard tilt (horizontal) of the loosen the setscrew, and turn the
adjusted, the feed feed dog is obtained when marker feed bar shaft 90 in the direction
dog height will be dot ‘A’ on the feed bar shaft is of the arrow, using a screwdriver.
changed. So, it is aligned with marker dot 'B' on feed To tilt the feed dog with its front
necessary to check rocker ‘1’. (If it is for heavy-weight down in order to prevent uneven
the height after tilt materials, the marker dot 'B' material feed, turn the feed bar
adjustment inclines forward the feed rocker shaft 90 in the opposite direction
shaft by 90 as standard.) from the arrow. (The standard tilt
for heavy- weight materials)
a
B
b d
A 1 c
a Front up b Standard
c Front down d Throat plate
Figure 31
Integrated Direct Drive Automatic Thread Trimmer Lockstitch Sewing Machine | Instruction Manual and Parts List 18
3.22
Loosen screws ‘2’ and ‘3’ in feed eye are flush with top surface of
eccentric cam ‘1’, move the feed throat plate when the feed dog de-
eccentric cam ‘1’ in the direction cends below the throat plate.
Feed Timing of the arrow or opposite direction To advance the feed timing in order
Adjustment of the arrow, and firmly tighten the to prevent uneven material feed,
screws ‘2’ and ‘3’. move the feed eccentric cam in the
Caution For the standard feed timing is align direction of the arrow.
If the feed the set screw ‘2’ on the feed eccent- To delay the feed timing in order to
eccentric cam is ric cam ‘1’ with set screw ‘4’ on the increase stitch tightness, move the
moved too far, main shaft ‘5’. feed eccentric cam in the direction
the needle will Make sure that the top surface of from the arrow.
be broken. feed dog and the top end of needle
Standard
1 4
2
Advanced
3
Delayed
Figure 32
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 19
3.23
Needle up or stitches correction
If the machine stops at intermediate
and press the switch ‘1’, the needle
Function of raised up to the up position.
One-Touch If the machine stopped at the end
Switch of the each seams, the swithc ‘1’ is 1
press to correct by one stitch for-
ward.
Figure 33
3.24
When the machine head and foot Put the foot pedal switch connec-
pedal switch has been installed to tor into the electric control con-
the machine, loosen the set screw nector ‘3’, then test the machine.
Connection of ‘1’ from the cover ‘2’. (Figure 34) (Figure 35)
The cover ‘2’ slide to the arrow
Foot Pedal direction.
After the sewing performance is
confirmed, install the cover ‘2’ by
Switch the set screw ‘1’ .
1 3
Figure 34 Figure 35
Integrated Direct Drive Automatic Thread Trimmer Lockstitch Sewing Machine | Instruction Manual and Parts List 20
4 Maintenance
4.1
Clean the machine periodically with
a soft and dry cloth to remove the
excess of dust on the machine head.
Machine Head Do not use any kind oflacquer thin-
Cleaning ner to wipe the surface.
4.2
If the machine was idle for a long
time, lubricate the machine accor-
ding to the instructions of topics
Lubrication 3.3 to 3.4
4.3
Check periodically if all safety de-
vices are properly installed and ad-
justed.
Safety
Check if all fixing and supporting
Inspection screws of the machine head are
adequately tighten.
Check if there is no overheating in
the electrical motor and check if the
power cord and plug are not dama-
ged.
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 21
Troubleshooting
Wrinkled stitches 3. Inadequate pressure of presser foot 3. Readjust the presser foot pressure
5. Needle is too thick 5. Use proper needle for fabric and thread
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 22
Problems Possible Causes Possible Solutions
1. Thread take-up lever highest position wrong 1. Set thread take-up lever highest position correctly
Needle thread 2. The needle thread is too short 2. Use proper needle for fabric and thread
comes out of
the needle hole 3. Needle thread tension is too strong 3. Adjust needle thread tension
after trimming 4. Wrong relation with rotary hook 4. Readjust the rotary hook
5. Needle doesn't center the needle hole of throat plate 5. Readjust the needle plate and presser foot
or presser foot
1. Low quality thread 1. Change the thread
2. Thread is thicker than needle hole 2. Use proper needle for fabric and thread
3. Wrong threading 3. Rethreaded the machine correctly
4. Thread tension is too strong 4. Readjust the thread tension nut
Thread break
start 5. Needle is installed wrong 5. Install needle correctly
6. Thread stand installed wrong 6. Install thread stand correctly
7. Thread tension disc, thread guide, needle, hook point 7. Grind off, polish or replace by a new parts
and needle plate are burred
8. Wrong relation with rotary hook 8. Readjust needle and hook point relation
1. Wrong relation of needle and hook point 1. Readjust needle and hook point
2. Wrong threading 2. Rethread the machine correctly
3. Needle is installed wrong 3. Installed needle correctly
Skip stitches
4. Inadequate thread tension 4. Readjust the thread tension nut
5. Hook point is damaged 5. Replace by a new part
6. Needle is bent 6. Replace needle
1. Wrong threading 1. Rethread the machine correctly
2. Thread is thicker than needle hole 2. Use proper needle for fabric and thread
Loosen stitches
3. Inadequate thread tension 3. Readjust the thread tension nut
4. Wrong setting of needle and hook point 4. Readjust needle and hook point
1. Thread tension is too strong 1. Readjust the thread tension nut
Wrinkled stitches 3. Inadequate pressure of presser foot 3. Readjust the presser foot pressure
5. Needle is too thick 5. Use proper needle for fabric and thread
Integrated Energy Saving Direct Drive Motor Lockstitch Sewing Machine | Instruction Manual and Parts List 23
Memo
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 24
Parts List
6.1
Frame &
Miscellaneous
Cover
Components
19
21 20
17
18
24 1
25
27 26 41
22
32
28 22
33
22
30
34 31 46
35
29
12
45
11
44 6
9 10 43
42
36 39
38 5
37
7
13 16
15 2 8
14
23
40
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 26
6.1
Frame &
No. Part No.
1 1281-01-20
Description
Machine frame 1
CE
QTY
1
CF
20 30 20 30
1 1
Miscellaneous 2 1230-01-01-02 Bed 1 1 1 1
3 134-02-01 Bobbin winder assembly 1 1 1 1
Cover 4 1281-05-13 Bobbin thread tension assembly 1 1 1 1
Components 5 1281-05-14 Pre-tension assembly 0 0 1 1
6 101-03-14 Two hole thread eyelet 1 1 0 0
7 1281-05-12 Thread tension assembly 1 0 1 0
8 101.03-23 Thread release pin 1 1 1 1
9 1280-01-21 Face plate 1 1 1 1
10 1280-01-22 Face plate gascket 1 1 1 1
11 1283-01-01-04 Revrese feed switch assembly 1 1 1 1
12 11-40120625-01 Screw SM3/16 x 28 L=6 1 1 1 1
13 101-01-10 Rubber plug 2 2 2 2
14 11-40121225-01 Screw SM13/16 x 28 L=12 3 3 3 3
15 1281-01-13 Two hole thread guide 1 1 1 1
16 11-70110620-02 Screw SM11/64 x 40 L=6 1 1 1 1
17 11-40120925-01 Screw SM 3/16 x 28 L=9 6 6 6 6
18 1273-12-25 Rectangular wire cramp 2 2 2 2
19 101-01-04 Back side plate 1 1 1 1
20 101-01-05 Back side plate gasket 1 1 1 1
21 1273-12-06 Coner wire clamp 1 1 1 1
22 101-01-11 Rubber plug 3 3 3 3
23 101-01-15 Bed screw stud SM 15/64 x 28 1 1 1 1
24 11-00090620-01 Screw SM 9/64 x 40 L=6 2 2 2 2
25 134-02-03 Thread cutter 1 1 1 1
26 11-70121020-02 Screw SM 3/16 x 28 L=10 3 3 3 3
27 11-40120625-01 Screw SM 3/16 x 28 L=6 1 1 1 1
28 1255-01-15 Three thread eyelet plate 0 0 1 1
29 101-03-34 Needle thread guide asemmbly 1 1 0 0
30 101.01-12 Rubber plug 1 1 1 1
31 11-80150710-01 Pre-tension screw 1 1 1 1
32 11-40120625-01 Screw SM 3/16 x 28 L=6 1 1 1 1
33 1277.01-12 Thread take-up cover 1 1 1 1
34 11-40110825-01 Screw SM 11/64 x 40 L=8 1 1 1 1
35 501-13-02-09 Plastic double wire clamp 1 1 1 1
36 11-20110920-02 Screw SM 11/64 x 40 L=9 2 2 2 2
109-01-44A Needle plate 0 0 1 0
37
101-06-36 Needle plate 1 0 0 0
38 101-01-17 Ruler stop seat 1 1 1 1
39 11-00110520-01 Screw SM 11/64 x 40 L=5.5 1 1 1 1
40 101-06-39 Slide plate assembly 1 1 1 1
41 101-01-02 Rubber plug 1 1 1 1
42 11-80150710-01 Screw SM 15/64 x 28 L=6 1 1 1 1
43 11-70110620-02 Screw SN 11/64 x 40 L=6 1 1 1 1
44 101-03-16 Arm thread guide (right) 1 1 1 1
45 109-01-20A Double holes rubber plug 0 0 1 1
46 101-01-03 Rubber plug 1 1 1 1
37
2
19
17 18
20
12 14
13
16
11 15
10
6 33
8
21
22 37
24
9
25
7
3 5
4 26
27
29 28
23
30
32
36
31 34
35
Integrated Enegy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 28
6.2
Arm Shaft
No. Part No.
1 11-80151550-01
Description
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 29
6.3
Needle Bar,
Upright Shaft,
and Rotating
Hook Driving
Shaft
Components
1
13 19
33
18
2 14
20
15
12
13 21
6
3 11
4 13
5
16
35
7 17
8 13
22
9 24
10 25
34 23
37
36
28
29
30
31
32
26
27
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 30
6.3
Needle Bar,
No. Part No.
1 101-03-07
Description
Rubber plug
CE
QTY
CF
20 30 20 30
1 1 1 1
2 1281-01-25 Needle bar bushing (upper) 1 1 1 1
Upright Shaft, 3 1281-05-32 Needle bar 1 1 1 1
and Rotating 4 120-02-07 Needle bar connection 1 1 1 1
Hook Driving 5 11-60090620-01 Screw SM 9/64 x 40 L=6 1 1 1 1
6 120-02-25 Slide block 1 1 1 1
Shaft 7 101-03-08 Needle bar bushing (lower) 1 1 1 1
Components 8 11-60080520-01 Screw SM 1/8 x 44 L=5 1 1 1 1
9 101-03-11 Needle bar thread guide 1 1 1 1
10 1955-01 Needle (Cat No.1955-01 size 14) 1 0 1 0
11 120-02-23 Slide block guide 1 1 1 1
12 11-60110820-01 Screw SM 11/64 x 40 L=8 2 2 2 2
13 11-80160810-01 Screw SM 1/4 x 40 L=8 2 2 2 2
14 101-05-26 Arm shaft bevel gear 1 1 1 1
15 101-05-25 Upright shaft bevel gear (upper) 1 1 1 1
16 101-05-20 Upright shaft bevel gear (lower) 1 1 1 1
17 101-05-18 Rotating hook driving shaft bevel gear 1 1 1 1
18 101-05-22A Upright shaft bushing (upper) 1 1 1 1
19 11-40120925-01 Screw SM 3/16 x 28 L=9 1 1 1 1
20 101-05-24 Upright shaft 1 1 1 1
21 101-05-21 Upright shaft bushing (lower) 1 1 1 1
22 101-05-14A Rotating hook driving shaft bushing 1 1 1 1
23 11-40120925-01 Screw SM 3/16 x 28 L=9 1 1 1 1
24 402-04-21 Thrust colla 1 1 1 1
101-05-07 Rotating hook driving shaft 1 0 0 0
25
1230-05-07 Rotating hook driving shaft 0 0 1 0
26 101-05-05 Positioning finger 1 1 1 1
11-60111120-01 Screw SM 11/64 x 40 L=11 0 0 1 1
27
11-60111020-01 Screw SM 11/64 x 40 L=10 1 1 0 0
28 101-05-09 Oil wick 1 1 1 1
29 101-05-08 Oil seal screw 1 1 1 1
101-05-01 Rotating hook assembly 1 0 0 0
30
109-03-24 Rotating hook assembly 0 0 1 0
101-05-03 Bobbin 1 1 0 0
31
402-04-04 Bobbin 0 0 1 1
101-05-02 Bobbin case 1 1 0 0
32
109-03-42-1 Bobbin case 0 0 1 1
33 1280-01-23 Needle bar sleeve felt 1 1 1 1
34 158-05-19 Hook driving shaft middle sleeve 0 0 1 1
35 1280-01-30 Needle bar thread guide 1 1 1 1
1283-05-04 Hook driving shaft bushing (front) assembly 1 1 0 0
36
1255-06-01 Hook driving shaft bushing (front) assembly 0 0 1 1
37 11-80160512-01 Screw SM 1/4 x 40 L=5 1 1 1 1
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 31
6.4
Presser Bar
Components
3
2
4
1 8
5
10 11 12
13
34
14 15
16
35
36
37 20
23
22
17
19 22
18
21 26
39
38
25
27
40 24 28
29
30
42 43
41
44
32
33
45 31
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 32
6.4
Presser Bar
No. Part No.
1 101-04-13
Description
Hand lifter
CE
QTY
CF
20 30 20 30
1 1 1 1
2 21-03810080-01 Washer 1 1 1 1
Components 11-30091020-01
3 Screw SM 9/64 x 40 L=10 1 1 1 1
4 31-04018000-09 Rubber ring 1 1 1 1
5 1281-01-10 Hand lifter cam assembly 1 1 1 1
6 101-04-20 Hand lifter link screw SM 5/16 x 24 2 2 2 2
7 101-04-21 Washer plate 2 2 2 2
8 101-04-19 Hand lifter link assembly 1 1 1 1
9 101-04-32 Hinge screw SM3/16 x 32 1 1 1 1
10 101-04-31 Hinge screw SM15/64 x 28 1 1 1 1
11 101-04-30 Lifting lever ring 1 1 1 1
12 101-04-33 Connecting rod vertical 1 1 1 1
13 24-05000000-08 E-ring 5 2 2 2 2
14 11-60111020-01 Screw SM 11/64 x 40 L=10 0 0 1 1
15 109-04-18 Presser plate B 0 0 1 1
16 11-40120625-01 Screw Sm 3/16 x 28 L=9 0 0 1 1
17 109-04-20-00 Cord holder bracket 0 0 1 1
18 1230-04-44 Arrester assembly 0 0 1 1
19 101-04-25 Thread tension release screw stud 1 1 1 1
20 101-04-24 Thread tension release wire plate 1 1 1 1
21 101-04-21 Washer plate 1 1 1 1
22 24-05000000-08 E-ring 5 2 2 2 2
23 1255-04-01 Thread tension release wire spring 1 1 1 1
24 101-04-34 Rubber bushing 1 1 1 1
25 101-03-30 Thread tension release supporting pin 1 1 1 1
26 24-04000000-08 E-ring 4 1 1 1 1
27 101-03-32 Washeer plate 1 1 1 1
28 101-03-33 Thread tension release supporting pin spring 1 1 1 1
29 11-40150925-01 Screw SM15/64 x 28 L=9 0 0 2 2
30 1230-04-42 Cord holder 0 0 1 1
31 11-60090820-01 Screw SM 9/64 x 40 L=8 0 0 2 2
32 1230-04-18 Cord holder 0 0 1 1
33 13-60623020-01 Nut SM 3/16 x 32 0 0 2 2
34 101-04-01 Presser regulator screw 1 1 1 1
35 101-04-02 Presser regulator nut 1 1 1 1
36 101-04-03 Presser guide bar 1 1 1 1
37 101-04-04 Presser spring 1 1 1 1
38 101-04-06 Presser bar guide bracket 1 1 1 1
39 1281-01-26 Presser foot bar 1 1 1 1
40 1255-04-02 Thread guide 1 1 1 1
41 11-80160810-01 Screw SM 1/4 x 40 L=8 1 1 1 1
42 11-40090825-01 Screw SM 9/16 x 40 L=8 2 2 2 2
43 101-04-10 Presser bar bushing (lower) 1 1 1 1
44 11-60091120-02 Presser foot screw SM 9/64 x 40 L=11 1 1 1 1
45 109-04-41 Presser foot assembly 1 1 1 1
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 33
6.5Feed
Mechanism
Components
68 7
6
3
1
16
8
2 9
4 53
10
31 5
30 17
14
32
22 23 21
11
21 18
20 19
28 29
15
25 52
51
66
48
27
26 33 47
35
34
36
49
50
45
42
63 64
46
62
44 61
43
41
40
39 65
38 59
37 24
56
60 69
54
58 67
57
37
55 12
13
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 34
6.5Feed
No. Part No.
1 1281-01-43
Description
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 35
6.5Feed
Mechanism
Components
68 7
6
3
1
16
8
2 9
4 53
10
31 5
30 17
14
32
22 23 21
11
21 18
20 19
28 29
15
25 52
51
66
48
27
26 33 47
35
34
36
49
50
45
42
63 64
46
62
44 61
43
41
40
39 65
38 59
37 24
56
60 69
54
58 67
57
37
55 12
13
Integrated energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 36
6.5Feed
No. Part No.
51 11-00090620-01
Description
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 37
6.6
Thread
Trimmer
Components
5
1
2
6 12
3 13
11
14
53
10
4 7
16 8
9 25
26 28 32
30 31
17
19 24 27
18 23
21
22
20
29
39
37 38
34
33
36
35
15
40 41
43
42
1 11-00580720-02
Description
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 39
6.7
Specific
Parts for
141G-30CE / CF 2
3
4 14 25
15 13
26
11
12
16
17
10
21
8 18
19
22
23
20
24
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 40
6.7
Specific
No. Part No.
1 101-06-02XH
Description
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 41
6.8
Lubrication
Components
18 18
17
16
3
20
4 19
6 14 10
8
11
21
15
12
13
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 42
6.8
Lubrication
No. Part No.
1 101-08-25
Description
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 43
6.9
Oil Reservoir
Components
4
1 3
17
5
16
6
2
18 9 10
8
14
13
13
12 12
11
15
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 44
6.9
Oil Reservoir
No. Part No.
1 101-09-02
Description
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 45
6.10
Machine
Accessories
5 6 7
11 9
10
8
16
12
4 1
15
14
3
13
QTY
No. Part No. Description CE CF
20 30 20 30
1 101-12-01 Machine hinge plate 2 2 2 2
2 120-09-02 Machine hinge rubber cushion 2 2 2 2
3 101-12-03 Nail 4 4 4 4
1955-01 3 needles per packet size 14 1 0 1 0
4
1955-01 3 needles per packet size 18 0 1 0 1
5 101-12-15 Screw driver (large) 1 1 1 1
6 101-12-16 Screw driver (medium) 1 1 1 1
7 101-12-17 Screw driver (small) 1 1 1 1
402-04-04 Bobbin 0 0 2 2
8
101-05-03 Bobbin 2 2 0 0
9 101-12-19 Machine rest pin 1 1 1 1
10 101-12-21 Oil pouch 1 1 1 1
11 101-09-22 Oil reservoir magnet 1 1 1 1
12 1277-14-02 Spanner 0 0 1 1
13 IP07042-001 Dust cover 1 1 1 1
14 1278-17-01-03 Foot pedal controller 1 1 1 1
15 1281-05-02-01-03 Pitman rod 1 1 1 1
16 101-11-01 Thread stand assembly 1 1 1 1
Integrated Energy Saving Direct Drive Lockstitch Sewing Machine | Instruction Manual and Parts List 46
P/N 364389-001
Rev 1 - Apr.2018
SINGER and the Cameo "S" Design are exclusive trademarks of The Singer Company Limited S.à r.l. or its Affiliates.
©2018 The Singer Company Limited S.à r.l. or its Affiliates. All rights reserved.
www.singer.com