Professional Documents
Culture Documents
Geo PDF
Geo PDF
Settings
(input for current task)
Materials and standards
Concrete structures : EN 1992-1-1 (EC2)
Coefficients EN 1992-1-1 : standard
Steel structures : EN 1993-1-1 (EC3)
Partial factor on bearing capacity of steel cross section : gM0 = 1.00
Timber structures : EN 1995-1-1 (EC5)
Partial factor for timber property : gM = 1.30
Modif. factor of load duration and moisture content : kmod = 0.50
Coeff. of effective width for shear stress : kcr = 0.67
Pressure analysis
Active earth pressure calculation : Coulomb
Passive earth pressure calculation : Caquot-Kerisel
Analysis method : dependent pressures
Earthquake analysis : Mononobe-Okabe
Modulus of subsoil reaction : input
Consider reduction of the modulus of subsoil reaction for a braced sheeting
Verification methodology : according to EN 1997
Design approach : 2 - reduction of actions and resistances
Partial factors on actions (A)
Permanent design situation
Unfavourable Favourable
Permanent actions : gG = 1.35 [–] 1.00 [–]
Variable actions : gQ = 1.50 [–] 0.00 [–]
Water load : gw = 1.35 [–]
1
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Anchors
Verification methodology : Limit states (LSD)
Reduction coefficients
Reduction. coeff of steel strength : gs = 1.35 [–]
Reduction coefficient of pull out resistance (soil) : ge = 1.35 [–]
Reduction coefficient of pull out resistance (grouting) : gc = 1.35 [–]
Geometry of structure
Structure length = 16.50 m
Concrete : C 30/37
Cylinder compressive strength fck = 30.00 MPa
Tensile strength fctm = 2.90 MPa
Elasticity modulus Ecm = 33000.00 MPa
Shear modulus G = 13750.00 MPa
Longitudinal steel : B420
Yield strength fyk = 420.00 MPa
Transverse steel: B420
Yield strength fyk = 420.00 MPa
Distribution of the modulus of subsoil reaction (in front and behind the wall)
Depth kh,p kh,z
[m] [MN/m3] [MN/m3]
0.00 0.00 0.00
1.50 28.00 28.00
2.00 28.00 28.00
3.00 35.00 35.00
16.00 35.00 35.00
16.50 35.00 35.00
Basic soil parameters
jef cef g gsu d
No. Name Pattern
[°] [kPa] [kN/m3] [kN/m3] [°]
Soil parameters
Fill
Unit weight : g = 17.00 kN/m3
2
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Stress-state : effective
Angle of internal friction : jef = 30.00 °
Cohesion of soil : cef = 0.00 kPa
Angle of friction struc.-soil : d = 18.00 °
Soil : cohesionless
Saturated unit weight : gsat = 17.50 kN/m3
Excavation
Soil in front of wall is excavated to a depth of 3.00 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
3
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
4
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Excavation
Soil in front of wall is excavated to a depth of 3.00 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
5
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
6
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Excavation
Soil in front of wall is excavated to a depth of 5.50 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
7
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
8
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Excavation
Soil in front of wall is excavated to a depth of 5.50 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
9
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
10
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Anchors forces
Depth Displacement Anchor force
No.
[m] [mm] [kN]
1 2.50 -2.0 400.41
2 5.00 -0.6 400.00
Internal stability of anchors - partial results
EA = 120.25 kN/m d = 18.00 °
Depth of theoretical footing under bottom of the pit H0 = 1.43 m
Row of EA1 d1 G C q Included Q F FKMAX
anchors [kN/m] [°] [kN/m] [kN/m] [°] rows of anchors [kN/m] [kN/m] [kN]
1 93.74 34.15 1432.50 0.00 4.11 1444.32 805.84 1611.69
2 167.02 34.52 1556.40 0.00 -6.17 1 1743.66 893.98 1787.97
Verification of internal stability of anchors
Max.allow.force in
Anchor force Verification
No. anchor
[kN] [kN]
1 400.41 1465.17 Is satisfactory
2 400.00 1625.43 Is satisfactory
Decisive anchor row : 1
Max. allowable force Fmax = 1465.17 kN > 400.41 kN = Finp
Overall verification of internal stability is SATISFACTORY
Excavation
Soil in front of wall is excavated to a depth of 8.00 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
11
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Input anchors
New Depth Force
No. Name Post-stressing
anchor z [m] F [kN]
1 No 2.50 DYWIDAG temporary anchor 0.6" St 1770 MPa 400.41
2 No 5.00 DYWIDAG temporary anchor 0.6" St 1770 MPa 403.79
Settings of the stage of construction
Design situation : transient
12
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Anchors forces
Depth Displacement Anchor force
No.
[m] [mm] [kN]
1 2.50 -2.0 400.41
2 5.00 -1.1 403.79
Internal stability of anchors - partial results
EA = 238.19 kN/m d = 18.00 °
Depth of theoretical footing under bottom of the pit H0 = 2.04 m
Row of EA1 d1 G C q Included Q F FKMAX
anchors [kN/m] [°] [kN/m] [kN/m] [°] rows of anchors [kN/m] [kN/m] [kN]
1 93.74 34.15 1777.21 0.00 17.24 1659.76 678.41 1356.82
2 167.02 34.52 1875.58 0.00 8.50 1 1846.04 674.49 1348.99
Verification of internal stability of anchors
Max.allow.force in
Anchor force Verification
No. anchor
[kN] [kN]
1 400.41 1233.47 Is satisfactory
2 403.79 1226.35 Is satisfactory
Decisive anchor row : 2
Max. allowable force Fmax = 1226.35 kN > 403.79 kN = Finp
Overall verification of internal stability is SATISFACTORY
Excavation
Soil in front of wall is excavated to a depth of 8.00 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
13
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Input anchors
New Depth Force
No. Name Post-stressing
anchor z [m] F [kN]
1 No 2.50 DYWIDAG temporary anchor 0.6" St 1770 MPa 400.41
2 No 5.00 DYWIDAG temporary anchor 0.6" St 1770 MPa 398.94
3 Yes 7.50 DYWIDAG temporary anchor 0.6" St 1770 MPa 400.00
List of the new anchors
DYWIDAG temporary anchor 0.6" St 1770 MPa
Anchor type : strand
Production set : DYWIDAG strand anchor
Depth : z = 7.50 m
Free length : l = 8.50 m
Root length : lk = 7.00 m
Slope : a = 15.00 °
Spacing : b = 2.00 m
c-s area of strand : A1 = 140.00 mm2
Number of strands : n = 3
Elasticity modulus : E = 195000.00 MPa
Pre-stressing force : F = 400.00 kN
Design strength of material : fu = 1770.00 MPa
Pull out resistance (soil) : Re = 650.00 kN
Pull out resistance (grouting) : calculate from concrete strength
Standard for concrete structures : EN 1992-1-1 (EC2)
Concrete strength in compression : fck = 30.00 MPa
Coefficient of cohesion : h1 = 0.70
Settings of the stage of construction
Design situation : transient
14
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
15
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Excavation
Soil in front of wall is excavated to a depth of 10.50 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
16
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
17
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Excavation
Soil in front of wall is excavated to a depth of 10.50 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
18
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Spacing : b = 2.00 m
c-s area of strand : A1 = 140.00 mm2
Number of strands : n = 3
Elasticity modulus : E = 195000.00 MPa
Pre-stressing force : F = 400.00 kN
Design strength of material : fu = 1770.00 MPa
Pull out resistance (soil) : Re = 650.00 kN/m
Pull out resistance (grouting) : calculate from concrete strength
Standard for concrete structures : EN 1992-1-1 (EC2)
Concrete strength in compression : fck = 30.00 MPa
Coefficient of cohesion : h1 = 0.70
Settings of the stage of construction
Design situation : transient
19
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Excavation
Soil in front of wall is excavated to a depth of 13.00 m.
Terrain profile
Terrain behind the structure is flat.
20
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Water influence
Ground water table is located below the structure.
21
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
22
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Excavation
Soil in front of wall is excavated to a depth of 13.00 m.
Terrain profile
Terrain behind the structure is flat.
Water influence
Ground water table is located below the structure.
23
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
24
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Dimensioning No. 1
Disp. min Disp. max Shear force min. Shear force max Moment min. Moment max.
[mm] [mm] [kN/m] [kN/m] [kNm/m] [kNm/m]
0.00 -6.56 -4.30 -0.00 0.00 -0.00 -0.00
0.82 -5.50 -3.50 -20.49 -5.79 2.11 6.67
1.65 -4.45 -2.69 -64.19 -15.96 10.78 39.49
2.48 -3.43 -1.91 -115.94 -29.18 29.38 112.62
2.50 -3.40 -1.89 -117.50 -29.61 30.14 115.54
2.50 -3.40 -1.89 -29.61 93.89 30.14 115.54
3.30 -2.48 -1.26 -41.20 59.62 43.42 74.69
4.13 -1.91 -0.77 -35.03 28.98 7.88 85.19
4.95 -1.70 -0.45 -93.84 12.48 -6.33 130.16
5.78 -1.47 -0.37 -17.88 85.09 -0.57 83.59
6.60 -1.36 -0.40 -23.40 48.93 -17.47 78.45
7.42 -1.52 -0.29 -81.45 22.71 -44.09 121.20
8.25 -1.61 -0.26 -20.07 96.60 -41.41 61.92
9.07 -2.35 -0.27 -21.11 55.40 -64.98 26.66
9.90 -3.16 -0.30 -79.53 10.51 -92.42 38.65
10.72 -4.00 -0.33 -35.99 121.59 -81.47 9.37
11.55 -4.68 -0.35 -45.56 65.33 -149.78 6.44
12.38 -5.02 -0.36 -26.57 5.92 -179.22 5.59
13.20 -4.95 -0.37 -56.51 1.90 -157.84 5.08
14.03 -4.51 -0.37 -82.76 1.85 -96.85 5.77
14.85 -3.84 -0.37 -57.45 3.15 -35.91 4.92
15.68 -3.09 -0.37 -18.27 3.68 -6.09 1.80
16.50 -2.31 -0.37 -0.00 0.00 -0.00 0.00
Maximum values of internal forces
Maximum displacement = -6.6 mm
Minimum displacement = -0.3 mm
Maximum bending moment = 134.94 kNm/m
Minimum bending moment = -179.22 kNm/m
Maximum shear force = 168.01 kN/m
Verification of RC cross section (Pile curtain d = 0.65 m; a = 1.00 m)
All construction stages are taken into the analysis.
25
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]
DE with Piles
Verification of anchors
Anchor with max. utilization - Nr. 4.
Utilization is 98.17 %
Anchors bearing capacity is SATISFACTORY
Depth Max. force Anchor strength Pull-out res. (soil) Pull-out res. (grouting) Verification
No.
z [m] F [kN] Rt [kN] Re [kN] Rc [kN]
1 2.50 401.69 550.67 481.48 427.71 is satisfactory
2 5.00 399.46 550.67 481.48 427.71 is satisfactory
3 7.50 405.28 550.67 481.48 427.71 is satisfactory
4 10.00 419.88 550.67 3370.37 427.71 is satisfactory
26
[GEO5 - Sheeting Check (demoversion) | version 5.2020.50.0 | Copyright © 2020 Fine spol. s r.o. All Rights Reserved | www.finesoftware.eu]