Professional Documents
Culture Documents
Temp Recorder
Temp Recorder
User’s Guide
Please read all the information in booklet before using the unit
Bioneer Corperation
8-11, Munpyeongseo-ro, Daedeok-gu, Daejeon
Tel: +82-1588-9788
Fax: +82-42-930-8600
Email: order@bioneer.co.kr
www.bioneer.co.kr
1
www.bioneer.com
Temp Recorder
Contents
1. Introduction .........................................................................................................3
2. System Components........................................................................................3
3. Installation ............................................................................................................4
Appendix 1.
ExicyclerTM 96 Temperature & Power Calibration Procedure
2
www.bioneer.com
Temp Recorder
1. Introduction
Temperature Monitoring System consists with Temperature Monitoring Software and Temp
Recorder, a kind of thermometer, which can measure the temperature of the 96 well PCR
thermo block and analyze the temperature profile to provide the necessary information to
calibrate temperature.
Temperature Monitoring Software can recode and display the temperatures of each well in
the graph at real time by using the Temp Recorder. The measured temperature data are
used for providing proper off-set values when you calibrate the temperature of a ExicyclerTM
96.
2. System Components
Temperature Monitoring System provides the following products also. Before using them,
please make sure it’s components.
3
www.bioneer.com
Temp Recorder
3. Installation
Temperature Monitoring Software and USB Driver (FTDI CDM Driver Package) should be
installed on the computer when you install the product, and installation sequence is
independent of the system used. Please refer this chapter and follow the instructions when
initial installation and reinstallation.
2) When the ‘Temperature Monitoring’ Install Shield Wizard starts, click ‘Next’ to
start the Installation. Then, the installation will proceed.
4
www.bioneer.com
Temp Recorder
5) When the installation is complete, click ‘Finish’ to finish the Installation Shield
Wizard.
5
www.bioneer.com
Temp Recorder
6
www.bioneer.com
Temp Recorder
7
www.bioneer.com
Temp Recorder
2) When the driver is installed completely, you can check the port number for
the driver like the below picture.
8
www.bioneer.com
Temp Recorder
9
www.bioneer.com
Temp Recorder
The Temperature Monitoring software can measure the temperature of the 96 well PCR
thermo block by using a Temp Recorder and recode the temperatures of each well in real
time. The measured temperature data are used for temperature calibration.
1.
2.
ITEMS DISCRIPTION
The serial port number connected to the
Serial Port
computer for a Temp Recorder
1 Toolbar
Connect Connecting to a Temp Recorder
10
www.bioneer.com
Temp Recorder
11
www.bioneer.com
Temp Recorder
12
www.bioneer.com
Temp Recorder
1.
2.
3.
ITEMS DECRIPTION
1. CSV Data File Selecting a recorded temperature file.
2. Temperature Graph It shows temperature graph of the 8 sensors.
Temperature It displays the standard deviation, accuracy, and
3.
Information uniformity of the selected area.
13
www.bioneer.com
Temp Recorder
14
www.bioneer.com
Temp Recorder
2) During the dragging, the red line shows the end point of the area you selected.
3) Then, it displays the standard deviation, accuracy, and uniformity of the selected
area at the ‘Temperature Information’ item.
15
www.bioneer.com
Temp Recorder
16
www.bioneer.com
Temp Recorder
17
www.bioneer.com
Temp Recorder
18
www.bioneer.com
Temp Recorder
1.
2.
ITEMS DESCRIPTION
System Resistance At here, the 8 resistances of a Temp Recorder can be
1.
Information calibrated and it shows you the calibration process.
The 8 sensor of a probe can be calibrated. Just before
System Sensor
2. the calibration, input the target temperature the values of
Information
which must be in the range of ‘Temperature Range’.
19
www.bioneer.com
Temp Recorder
20
www.bioneer.com
Temp Recorder
1.
2.
3.
4.
21
www.bioneer.com
Temp Recorder
ITEMS DESCRIPTION
The buttons for reading, updating, or
Read, Update, Initialize
1 initializing the system memory of the
System Information
Temp Recorder.
The information of the Temp Recorder:
2 System Information System ID, Probe ID, and Calibration
Date.
It shows the calibration information of the
3 Calibration Information
system main body and the probe sensor.
Open, Save The buttons for opening or saving the
4
System Information system information as text type file.
22
www.bioneer.com
Temp Recorder
23
www.bioneer.com
Temp Recorder
24
www.bioneer.com
Temp Recorder
6. Troubleshooting
[Solution]
To solve this problem, you must install the USB Driver again.
1) After inserting the CD delivered with the system, open the ‘USB
Driver‘ folder and double-click ‘CDM20824_Setup.exe’.
25
www.bioneer.com
Temp Recorder
26
www.bioneer.com
Temp Recorder
Appendix 1.
ExicyclerTM 96 Temperature & Power Calibration Procedure
TM
This appendix explains how to calibrate Exicycler 96 system using the Temperature
Monitoring software and the ExiHardWareSet software.
TM
To calibrate Exicycler 96 system, you have to follow the Temperature Calibration step
first, the Power Calibration step second, and the Temperature Record step last.
At the Temperature Calibration step first, reference temperature values for NTC sensors
are calculated through the Temperature Monitoring software. And at the Power Calibration
step second and the Temperature Record step last, the calibrated values are evaluated for
whether the values are correctly working or not.
27
www.bioneer.com
Temp Recorder
TM
2. Connecting between the PC and Exicycler 96
TM
2.1. Connecting between the PC and Exicycler 96
TM
1) Removing the side panels of Exicycler 96
TM
Remove the bolts first which are in the rear side of Exicycler 96 and remove
the side panels of it next.
[Before Removing the P1011 cable] [After Removing the P1011 cable]
28
www.bioneer.com
Temp Recorder
- Connect the serial cable for download to the socket for the P1011.
TM
- Turn on the power of Exicycler 96.
TM
2.2. Connecting the ExiHardwareSet software to Exicycler 96
1) Execute ‘ExiHardwareSet.exe’ program.
2) Select a serial port at the ‘Configuration & Run’ menu.
3) Click ‘Connect’ button.
② ③
TM
2.3. Mounting the Temperature probe at the Exicycler 96 and connecting it to the
Temperature Monitoring software
1) Connect the USB cable from the Temp Recorder to the PC.
2) Mount the Temperature probe at the thermal block of the ExicyclerTM96 like the
below picture.
④ ⑤
29
www.bioneer.com
Temp Recorder
② ③
②
①
30
www.bioneer.com
Temp Recorder
TM
4.2. Monitoring the Block Temperature of the Exicycler 96 using the Temperature
Monitoring software
1) Click ‘Run’ button and input a file name so that the Temperature Monitoring
software can save the temperature profiles as a CSV file type.
31
www.bioneer.com
Temp Recorder
32
www.bioneer.com
Temp Recorder
3) Copy the calculated result values from the Temperature Monitoring and then,
paste them to the Offset item of the ExiHarewareSet software like the below
picture. (S0 = Left / S1 = Center / S2 = Right)
4) Click ‘Write OffSet’ button. Then all the calculated values for the references
temperature are stored to the memory of the ExicyclerTM96.
33
www.bioneer.com
Temp Recorder
① ②
TM
7.2. Monitoring the Block Temperature of the Exicycler 96 using Temperature Monitoring
software
1) Click ‘Run’ button and input a file name so that the Temperature Monitoring
software can save the temperature profiles as a CSV file type.
34
www.bioneer.com
Temp Recorder
35
www.bioneer.com
Temp Recorder
9.1. Performing the Temperature Record step using the ExiHardwareSet software
1) Click ‘Normal’ button.
2) Click ‘Temp Record’ button so that the final step can be processed.
②
①
TM
9.2. Monitoring the Block Temperature of the Exicycler 96 using Temperature Monitoring
software
1) Click ‘Run’ button and input a file name so that the Temperature Monitoring
software can save the temperature profiles as a CSV file type.
36
www.bioneer.com
Temp Recorder
37
www.bioneer.com
Temp Recorder
38
www.bioneer.com