Professional Documents
Culture Documents
Once printed this specification becomes an uncontrolled copy of the online version.
10.35.33.2110
NS-1™ Number: NS 10.35.33.2110
Revision Date: June 2007
Equipment Name: SLIDING SLEEVE ASSEMBLIES
Manufacturer: GENERAL
Model/Type: VARIOUS
Material Group: MEDIUM ALLOY STEEL
Service: NON-SOUR
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 1
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
SCOPE
This COMBINED NS-1™ specification specifies the minimum quality and inspection requirements applied to
wrought Medium Alloy Steel Sliding Sleeve Assemblies.
It applies to:
• Non-Sour service conditions, employing medium alloy steel (e.g. 9Cr to 13Cr).
• All sizes and Rated Working Pressures of less than 69 MPa (10,000 psi).
• Equipment with Rated Working Pressures of 69 MPa (10,000 psi) and above, should meet the requirements
of NACE MR0175 as standard practice. Use NS-1™ Specification 10.35.33.2111.
• All operating temperatures.
The matrix of this COMBINED NS-1™ specification provides a quality template that can be applied to any make
and type of Sliding Sleeve Assembly. This COMBINED NS-1™ specification in combination with the manufac-
turer’s parts list(s) and drawing(s) completes the product quality specification.
When ordering spare parts or sub-assemblies, the applicable quality requirements shall be those specified for
the components supplemented by the relevant requirements called out for the complete assembly.
Design verification, approval and other design related parameters are specifically excluded from this COMBINED
NS-1™ specification.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 2
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
SUPPLEMENTARY REQUIREMENTS
The following requirements are supplementary to, and shall be applied in conjunction with, the Quality Sub-
specifications of this NS-1™ Specification:
1. WELDING
No fabrication welding shall be performed.
2. MATERIAL TESTING
(Ref. Sub-Spec. 10.1 & Sub-Spec. 10.4)
3. COMPLETE ASSEMBLY
(Ref. Sub-Spec. 100.2)
Each assembly shall be hydrostatically tested to the manufacturer’s procedures and specifications with the following
minimum requirements:
The timing of the holding periods shall not start until the test pressure has stabilized, the equipment
and measuring devices have been isolated from the pressure source and the external surfaces of the
equipment thoroughly dried.
The above test durations shall be applied to the assembly first in the fully extended position and then
in the fully contracted position.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 3
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Where the test pressure is limited by the threaded end connections, it shall be calculated using the
following formula:
P = (2 • f • Yp • t) / D
Where:
P = hydrostatic test pressure, in (MPa)
f = a factor of 0,8 of specified minimum yield strength
Yp = specified yield strength for the pipe body (MPa)
t = nominal design wall thickness adjacent to thread connection (mm)
D = nominal outside diameter of the connecting thread (mm)
As a minimum, the hydrostatic test pressure shall not be less than the equipment rated working
pressure.
4. FUNCTIONAL TESTING
(Ref. Sub-Spec. 130.1)
Functional testing shall be carried out to the manufacturer’s specification but shall include the following as a
minimum:
• Jar energy required to disengage the collets from both end positions and the force required to stroke the
sleeve shall be measured and recorded. The recorded values shall be within the manufacturer’s documented
upper and lower acceptance limits.
• The above functional test may be carried out after step 1 of the hydrotest cycle, otherwise the equipment
shall be re-hydrotested to rated working pressure and held for 5 minutes. The timing and acceptance re-
quirements of 4.1 above shall apply
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 4
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
MATRIX
Equipment Name: Sliding Sleeve Assemblies
Specification: 10.35.33.2110
Manufacturer: General
Model/Type: Various
Material Group: Medium Alloy
Service: Non-Sour
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 5
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 6
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 7
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 8
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 9
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Complete Assembly
Number Title
10.1 Material Certificates – General
10.2.2 Material Certificates – Assembly Certificate
20.3 Traceability – Serialization Traceability
90.1 Dimensional Inspection – General
100.2 Hydrostatic Testing – General
130.1 Functional Testing – General
160.1 Non-Conformity Procedure – General
170.1 Boxing/Packing/Marking – General
170.2 Boxing/Packing/Marking – Critical Service (H2S, CO2, Low Temperature)
180.1.3 Quality Documentation for Non-Welded Products
Notes
1. When applicable; Threaded parts shall be examined in accordance with Sub-Specs 40.6.1.3, 40.6.2.3 &
40.6.3.2 MT for Ferrous Steels and Sub-Specs 40.12.1, 40.12.2.3 & 40.12.3.2 PT for Non-Ferrous steels, as
shown on the matrix.
2. Parts designed to take combined loads (e.g. tension & compression): The most stringent quality requirements
based on the "Worst Case" loading condition shall apply. In such cases class code B1, D shall be default.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 10