Professional Documents
Culture Documents
Product Information
Inverter System 48 V DC
for Telecommunication
1 / 10
Inverter system IS920 IS920 Inverter system
Input: 48 V DC
Output: 230 V AC / 50 Hz
5400 W / 6750 VA
2/9
Inverter system IS920 Scalability Modular design
The 19” subrack includes 3 prewired slots for The modular design makes it possible to
inverter module WR92. According to the exchange easily faulty equipment or increase
actual power profile different output power output power by additional inverter modules.
levels can be reached (1.8 kW, 3.6 kW or
5.4 kW).
Low storage costs
Due to the limited number of required compo-
Quick installation nents for building up a complete inverter
The subrack is equipped with a backplane system the costs for stocking and administra-
including several connection points to wire tion of different parts are very low.
input and output cables and fuses. Installa-
tion of modules is quick and easy by hot The system requires only few components:
plug-in.
• prewired 19” subrack
High power density • inverter modules WR92 and
• static transfer switch STS92
In only 5 HU height a total output power of
5400 W / 6750 VA including static transfer • AC distribution unit IS920
switch can be installed. • Manual bypass switch
3 / 10
Operation Modes DC input (battery) AC input (mains)
INV
STS
The online operation mode is recommended, because of the better quality of the output AC voltage (no
voltage deviations and spikes). If the reduction of system’s power consumption is the main target besides the
safe AC feeding, the offline mode should be used.
4 / 10
Inverter System IS920 Modular design
The subrack combines prewired slots for 3 inverters of series WR92 and 1
static transfer switch STS92. The connection to the incoming and outgoing
cables and between the modules are made on a backplane.
The power modules are cooled by internal fans. The fans are speed controlled
and monitored. The air flow direction is from the front to the rear side.
A minimum space of 50 mm between the air outlets of the modules and the
rear panel of the cabinet is needed. Therefore the installation within standard
ETSI cabinets with a depth of 400 mm is possible.
Efficiency 91 %
Dimensions (WxHxD) 483 (19”) x 88.5 (2 HU) x 350 mm
Temperature range Operation 0°C…+40°C
Cooling Fan cooling (speed controlled, monitored)
Protection class 1 (electrical); IP20 (mechanical) front panel
Safety standards EN60950, VDE0110, VDE0100 part 410, EN60146
General EMC standards EN55011/22 class “B”, EN61000-4 part 2/3/4/5
Data EN50081-1, EN61000-6-2
Noise < 50 dB(A) at 1 m distance
Switch over time < 4 ms (after detection)
Ambient conditions IEC 721-3-3 class 3K3/3Z1/3B1/3C2/3S2/3M2
Colouring (front panel only) RAL7035 (powder coated)
Max. installation altitude <= 1500 m altitude
Weight app. 19 kg
5 / 10
Connection Unit IS920 Connection unit with Manual Bypass Switch
The connection unit with 3 HUs houses up to four loads. The connection of
loads needs few time and effort the terminals being accessible from the front.
The connection unit includes a manual bypass switch. It allows switching off the
subrack IS920 from AC voltage for maintenance work. During this time the load
is supplied with voltage directly from mains, such ensuring the uninterrupted
supply of AC consumers.
6 / 10
Inverter Unit WR92 WR92 with digital control
The inverter WR92 includes the newest switching
technology with controlling by digital signal
processor.
The inverter is able to run in parallel operation
without any additional components and increases
the reliability of the AC system.
WR92 modules can be integrated in empty slots
of a system during normal operation (hot plug-in).
For higher reliability the synchronisation bus is
working in a redundant mode.
Up to 3 modules together with a static transfer
switch unit can be installed in a 19” subrack with 2
HU.
7 / 10
Static Transfer Switch STS92 Highest reliability
The static transfer switch STS92 is a compact electronic
switch. The digital regulation guarantees minimized synchro-
nisation time of inverter and mains frequency. Due to this
high synchronisation speed the unit can be used together
with diesel Genset as transfer mains supply.
The transfer time between the two inputs is less than 4 msec.
Therefore the STS92 is suitable for use in IT environment.
The static transfer switch monitors the voltage level, fre-
quency and the synchronisation of both incoming sources. In
combination with the inverter WR92 the unit can operate in
online- or offline-mode. This function is programmable at site.
All main functional parameters and measuring values will be
displayed on the LCD panel.
8 / 10
LCD display of the
Static Transfer Switch STS92
Static Transfer Switch
9 / 10
Nokia Siemens Networks GmbH & Co. KG
Power Supply Systems
Rudolf - Vogel - Bogen 5
D-81739 München
Order No.
A30050-X6390-X92-2-76K6
10 / 10