Professional Documents
Culture Documents
OffHighway Truck FDB00001UP (MACHINE) POWERED BY 3516B Engine(SEBP3976 152) Documentación
Pantalla anterior
Bienvenido: r120oj
Producto: TRUCK
Modelo: 793D TRUCK FDB00338
Configuración: 793D OffHighway Truck FDB00001UP (MACHINE)
POWERED BY 3516B Engine
Pruebas y Ajustes
793D OffHighway Truck Steering System
Número de medio RENR833604 Fecha de publicación 01/02/2012 Fecha de actualización 20/01/2016
i03512980
Front Wheel Bearing Adjust Standard Wheel
SMCS 4201025BD
Illustration 1 g00674965
Front wheel
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/s… 1/3
1/16/2017 793D OffHighway Truck FDB00001UP (MACHINE) POWERED BY 3516B Engine(SEBP3976 152) Documentación
(1) Axle
(2) Wheel
(3) Rubber toric ring
(4) Bolts
(5) Retainer plate
(6) Shim pack
(7) Bolts
(8) Bearing assembly
(9) Bearing assembly
(10) Seal retainer
(11) Rim
1. Remove the thread lock compound from the thread holes.
2. Install seal retainer (10), bearing assembly (9), wheel (2) and bearing assembly (8) onto axle (1) .
3. Without using shims (6), use seven equally spaced bolts (7) to assemble retainer plate (5) to the axle (1).
4. Torque seven bolts (7) to 50 N·m (37 lb ft) while you rotate the wheel for at least 3 revolutions. Rotating
the wheel helps to seat the bearings.
5. Loosen bolts (7) .
6. Repeat Step 4.
7. Measure the gap from the end of axle (1) to the top of retainer plate (5). Record the value. This value will
be used to ensure movement of bearing assembly (8) on axle (1) .
8. Loosen bolts (7) by 60 degrees. Rotate the wheel for at least three revolutions.
9. Measure the gap from the end of axle (1) to the top of retainer plate (5). Record the value. Compare this
value to the value that was recorded in Step 7. If the two measured gaps are equal, bearing assembly (8) is
not sliding properly. Use the following procedure to correct the bearing assembly:
a. Remove bolts (7), retainer plate (5) and bearing assembly (8) from axle (1) .
b. Check for burrs.
c. Repeat Step 3 through Step 9 until bearing assembly (8) begins to slide properly.
10. Torque seven bolts (7) to 20 N·m (15 lb ft) while you rotate the wheel for two revolutions.
11. Tighten bolts (7) to a torque of 30 ± 5 N·m (22 ± 4 lb ft) while you rotate the wheel for two revolutions.
12. Repeat Step 11 until there is no movement of bolts (7) .
13. Use a depth micrometer to measure the distance from the end of axle (1) to the outer face of retainer plate
(5). Use two threaded holes on the retainer plate (5). Record the measurements.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/s… 2/3
1/16/2017 793D OffHighway Truck FDB00001UP (MACHINE) POWERED BY 3516B Engine(SEBP3976 152) Documentación
Note: If the difference between the two measurements exceeds 0.13 mm (0.005 inch), do not continue
with the adjustment procedure. Remove the wheel, the bearing assemblies and the seal retainer from the
axle. Check the axle and the bearing assemblies for any interference that prevents the correct seating of
the wheel bearings. Repeat Step 2 through Step 12 until the measurements are within 0.13 mm (0.005
inch). When the correct tolerance is achieved, record the average of the measurements.
14. Remove retainer plate (5) .
15. Use an outside micrometer to measure the thickness of retainer plate (5) at the threaded holes that were
used to take the measurements in Step 13. Use these measurements to determine the average thickness of
retainer plate (5). Record the measurement.
16. Subtract the average thickness of the retainer plate from the average measurement that was obtained in
Step 13. Record this dimension.
17. Install shim pack (6) between axle (1) and retainer plate (5). The shim pack thickness should equal the
dimension that was obtained in Step 16 minus 0.07 ± 0.03 mm (0.003 ± 0.001 inch).
Note: Put 9S3263 Thread Lock Compound on the threads of bolts (7) before final assembly.
18. Install 14 bolts (7) .
19. Torque 14 bolts (7) to 530 ± 70 N·m (390 ± 52 lb ft) while you rotate the wheel.
Copyright 1993 2017 Caterpillar Inc.
Todos los derechos reservados.
Mon Jan 16 2017 14:13:43 GMT0300 (Pacific SA Daylight Time)
r120oj
Red privada para licenciados del SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/sisweb/s… 3/3