Professional Documents
Culture Documents
BS4168 PDF
BS4168 PDF
4168:2004
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
ICS 49.080
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Satair/5905513002
No reproduction or networking permitted without license from IHS Not for Resale, 05/09/2011 07:06:00 MDT
BS EN 4168:2004
National foreword
This British Standard is the official English language version of EN 4168:2004.
It supersedes BS EN 4168:2003 which is withdrawn.
The UK participation in its preparation was entrusted to Technical Committee
ACE/12, Aerospace fasteners and fastening systems, which has the
responsibility to:
Summary of pages
This document comprises a front cover, an inside front cover, the EN title page,
pages 2 to 6, an inside back cover and a back cover.
The BSI copyright notice displayed in this document indicates when the
document was last issued.
English version
Série aérospatiale - Colliers de fixation à ressort en trois Luft- und Raumfahrt - Rohrschellen, federnd, dreiteilig -
parties - Demi-colliers extérieurs, en acier résistant à chaud Außenschelle aus hochwarmfestem Stahl FE-PA2601
FE-PA2601 (A286) (A286)
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4168:2004: E
worldwide for CEN national Members.
Contents Page
Foreword..............................................................................................................................................................3
1 Scope ......................................................................................................................................................4
2 Normative references ............................................................................................................................4
3 Required characteristics.......................................................................................................................4
4 Designation ............................................................................................................................................6
5 Marking ...................................................................................................................................................6
6 Quality assurance ..................................................................................................................................6
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
2
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Satair/5905513002
No reproduction or networking permitted without license from IHS Not for Resale, 05/09/2011 07:06:00 MDT
EN 4168:2004 (E)
Foreword
This document (EN 4168:2004) has been prepared by the European Association of Aerospace
Manufacturers - Standardization (AECMA-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at
the latest by June 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and the United Kingdom.
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
3
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Satair/5905513002
No reproduction or networking permitted without license from IHS Not for Resale, 05/09/2011 07:06:00 MDT
EN 4168:2004 (E)
1 Scope
This standard specifies the characteristics of outer clips, three part clips, spring tension, in FE-PA2601 for
applications at a maximum temperature of 260 °C, for aerospace applications.
They shall be assembled with parts from EN 4166 and EN 4167.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 4166, Aerospace series – Clips, spring tension, three parts – PTFE bushes
EN 4167, Aerospace series – Clips, spring tension, three parts – Inner clips in heat resisting steel
FE-PA2601 (A286)
3 Required characteristics
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
See Figure 1 and Table 1.
Dimensions and tolerances are in millimetres. They apply after passivation.
3.2 Materials
EN 3638
3.5 Hardness
260 HV to 345 HV
1) Published as AECMA Prestandard at the date of publication of this standard
4
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Satair/5905513002
No reproduction or networking permitted without license from IHS Not for Resale, 05/09/2011 07:06:00 MDT
EN 4168:2004 (E)
Key 6 marking
1 break sharp edges 0,1 to 0,4 7 R = 2 to 2,5
2 10,4 to 10,8 8 5,1 to 5,3
3 direction of grain 9 diameter 5,5 to 5,8
4 R = 1 to 1,5 10 R = 7 to 9
5 1,5 to 2 11 view along L
Figure 1
Table 1
Diameter A B C E G Mass
code kg/1 000 parts
max. min. max. min. max. min. max. min. max. min. ≈
004 8,7 8,1 13,6 13,1 8,7 8,1 17
006 10,6 10 14,5 14 10,6 10 19
0,9 0,7 45° 35°
008 12,5 11,9 15,5 15 12,5 11,9 22
010 14,3 13,7 16,4 15,9 14,3 13,7 24
012 16,7 15,7 17,8 17,3 16,5 15,9 35
55° 45°
014 18,5 17,5 18,7 17,7 18,3 17,7 39
016 20,3 19,3 19,6 18,6 20,1 19,5 45
018 22,1 21,1 20,5 20 21,9 21,3 1,1 0,9 44
020 24 23 21,5 21 23,8 23,2 65° 55° 53
025 28,3 27,3 24 23,5 28,1 27,5 62
032 35,3 34,3 27,5 27 35,1 34,5 78
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
5
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Satair/5905513002
No reproduction or networking permitted without license from IHS Not for Resale, 05/09/2011 07:06:00 MDT
EN 4168:2004 (E)
4 Designation
EXAMPLE
NOTE If necessary, the code I9005 shall be placed between the description block and the identity block.
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
5 Marking
EN 2424, style A, as indicated on Figure 1.
6 Quality assurance
The manufacturer’s quality systems shall conform to EN 9100.
6
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Satair/5905513002
No reproduction or networking permitted without license from IHS Not for Resale, 05/09/2011 07:06:00 MDT
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: orders@bsi-global.com. Standards are also
available from the BSI website at http://www.bsi-global.com.
--```,,,,``,`,,,```````,,,``,,``-`-`,,`,,`,`,,`---
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: info@bsi-global.com.
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: membership@bsi-global.com.
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: copyright@bsi-global.com.
W4 4AL