Professional Documents
Culture Documents
1. Direct mounting to the expansion slot in the MPU of 2. Connecting to DVP 1. Switch the DU-01 to TC-01
TC-01
the EP/EH series series PLC via accessory mode (please see the back of
cable the DU-01), and select RD (to Indication of the connected MPU model
read P, D and F in the MPU of
Indication of internal data storage model
PLC) or WR (to write the data
1. In TS-01 mode, DU-01 (specified as TS-01 hereof) has the following functions:
Display
Selection
RD read mode
• Read/Write both the internal devices of PLC (e.g. perpetual calendar, bit devices (X, Y, M, S) HH-MM-SS +
ESC No Save
and word devices (T, C, D)) and the Control Register (CR) inside the extension units.
• Support the read/write 32-bit data register. P,D,F selection
OK Confirm & update time
• Set Start-up display and power save mode.
• Monitor the devices. Confirm
ESC
Device
• If connect the accessory cable to ES-series without perpetual calendar, the Time Display will
start from 00-00-00 calculated by the microprocessor of DU-01 (timing error may occur). Device
Selection
• Give RUN-STOP command to PLC. Device Selection
X, Y, M, S
2. In TC-01 mode, DU-01 (specified as TC-01 hereof) has the following functions for DVP all series: T, C, D
• Read/write the program P, data register D and file register F from PLC. CR P(Program) D (Data Register) F (File Register)
DD(32-bit)
• Copy program and data.
• Support the PLC password protection.
ESC OK
Specify a number
Overview of the Product - Names of Parts
Device
P: program area indication Monitor
1 Press and hold for 3 sec. OK
(TC-01) Number Selection Force On/Off setting
OK OK
2 W: write (WR) indication (TC-01) Bit Device confirm Monitor status of 8 consecutive
Device devices from the specified number
1 5 3 R: read (RD) indication (TC-01) ESC ESC
Setting reading range.
Reading P (Program). Reading F (file register)
4 “In communication” indication (default start & end
2 6 D: Data Register indication
Press OK to complete entering & return
You can press ESC to
addresses are latched You can press ESC to
5 pause reading. pause reading.
(TC-01) area range. User can
3 7 Number Selection OK
Enter a number
Press and hold for 3 sec.
F: File Register indication OK OK
re-set it.)
6 Word Specified No.
(TC-01) Device confirm Enter Set Value
4 8 7
CR: Control Register indication
Device
ESC ESC
Display
ESC
Enter start address
Finish reading.
(Extension Module)
d1EC is the CHKSUM 2746 is the CHKSUM
8 ER: Error message display of writing program of writing data
9 9 Display Area 3. Start-up display mode setting (press + buttons simultaneously)
Device Confirm R W P D F CR ER
ESC + OK
Mode selection On/Off
ESC + OK
Field selection
Set the contents ESC
for setting
change it.)
W P D F CR ER
Current value
OK OK OK
6 DIMENSIONS & ACCESSORY display
K
(Press and hold for 3 sec.)
Connecting to Move to the
DVP-PLC COM1 Word device Select device Confirm device Set the number ESC
digit to be set
(RS-232 Port) T, C, D, DD
ESC ESC
The accessory cable connects the DU-01 (the extension COM port of figure above) and
K
DVP-series PLC COM1 (RS-232) port. Therefore, the DU-01 can be connected to ES/SS/EX W P D F CR ER (Press and hold for 3 sec.)
or SA/SX models via the cable, as well as direct installation in the extension slot of EP/EH Specify the expansion Current value
OK Specify CR number OK OK Enter Set Value mode
models. unit number display
K
Error-04 F-read error. ES series does not have file registers. ESC + OK