Professional Documents
Culture Documents
5 LF - SS1007 - E01 - 1 ZXSDR ENodeB Hardware Structure 74pdf
5 LF - SS1007 - E01 - 1 ZXSDR ENodeB Hardware Structure 74pdf
Structure
ZTE University
Objectives
eNodeB Overview
ZXSDR B8200 L200 Hardware Structure
ZXSDR R8882 Hardware Structure
ZXSDR eNodeB Maintenance
LTE Base Station Family
BBU B8200
RRU R8882/R8862/R8972/R8964
Pico BS8912/BS8922
Femto BS8102
Qcell R8108
MME/S-GW MME/S-GW
EPC
S1
Interface between EPS
MME/SGW & eNodeB
X2 E-UTRAN
eNB eNB
X2 X2
UE eNB
Interface between
eNodeBs
eNodeB=BBU+RRU
Node B RNC eNodeB
Cell management
Image business
Mobility management
Large capacity
All-IP architecture
LTE
Distributed Integrated
Universal
RRU
RRU
RSU Features
MicroTCA architecture
Multi-Standard support
Baseband sharing and
BBU software configurable
RRU sharing and software
configurable
BBU
BBU+RRU
All-IP transmission, provides
IP over E1/STM-1 interface
Clearer and
Simpler Network
eNodeB Overview
ZXSDR B8200 L200 Hardware Structure
ZXSDR R8882 Hardware Structure
ZXSDR eNodeB Maintenance
Hardware Structure
Grounding ≤5Ω
The ground resistance can be lower than 10 Ω in areas where the
number of thunderstorm days per year is less than 20.
Item Specification
3 cells/1 BPL1 120 W
6 cells/1 BPN0 90 W
24 carrier frequencies + 3 carrier 125 W
sectors (128 CEs) + 6 cells/ 1BPN2
12 carrier frequencies + 6 carrier 125 W
sectors (256 CEs) + 6 cells/ 1BPN2
Item Specification
Power consumption (typical 80 W
configuration at normal temperature)
BPL1/BPL1A/BP 3–8 The baseband processing boards are configured in accordance with the required
N0/BPN0A/BN processing capability.
P2
SA 13
PM 14–15 • Two PMs are required when more than one baseband processing boards are
configured.
• Two PMs are required when two power supplies are operating in active/standby
mode.
FAM 16
FS 3–4 Optional. The FS board is required for the multi-mode configuration.
UES Optional. The UES boards are configured in accordance with the actual Ethernet
requirement.
• Supporting the SyncE function: slot 2 and slot 5
• Flashing slowly (0.3 s on, 0.3 s off): The board is operating properly.
HS - - Reserved
Ethernet Green - • Left indicator
interface On: The interface is connected successfully.
indicator Off: The interface is not connected.
• Right indicator
Flashing: Data is being transceived.
Off: Data is not being transceived.
Button
CR0 Panel
• Flashing slowly (0.3 s on, 0.3 s off): The board is operating properly.
• Flashing quickly (70 ms on, 70 ms off): The external communication of the board is
not normal.
ALM Red Alarm indicator • On: There is a hardware alarm reported.
BPN0/BPN0A Panel
Notes:
BPN0A has the same panel as BPN0, but only TX0 RX0 to TX2 RX2 CPRI optical interfaces
are available on BPN0A.
BPN2 Panel
• Flashing slowly (0.3 s on, 0.3 s off): The board is operating properly.
• Flashing quickly (70 ms on, 70 ms off): The external communication of the board is not
normal.
ALM Red Hardware • On: The hardware is faulty.
fault
indicator • Off: There is no hardware fault.
OF0– Green Optical • On: The optical interface link is not operating properly.
OF5 interface
link state • Flashing slowly (0.3 s on, 0.3 s off): The optical interface is communicating properly.
indicator
• Off: The optical module is not in position or the optical module does not receive any
optical signal.
CST - - Reserved
HS - - Reserved
BLS - - Reserved
BSA - - Reserved
LNK - - Reserved
Interface Description
PM3 PM4
Type Description
PM3 Supports 300 W power output and 10-channel power outputs.
PM4 As a high-power power board, PM4 supports 400 W power
output and 10-channel power outputs.
Interface Description
Function:
Provides the fan control
function and interface.
Provides a temperature
sensor to detect
temperature of air intake.
Displays the fan status.
The UES board provides the Ethernet synchronization function, and can
operate as a layer-2 switch. When operating as an Ethernet switch, this
board converges the data of other BBUs on its physical site, meaning
that there are multiple BBUs on a single physical site.
Interface Description
X1–X2 Electrical interfaces, fixedly used as cascading interfaces.
X3/ULPINK Electrical interface, used as a cascading interface or an uplink interface.
UPLINK Electrical interface or optical interface, fixedly used as a cascading
interface.
X4/UPLINK Optical interface, used as a cascading interface or an uplink interface.
The Universal Clock Interface (UCI) board is a RGPS interface board. The
UCI board receives, converts, and transfers BBU clocks.
Interface Description
TX RX 125 Mbps optical interface. Used to connect to an external RGPS device to get input signals.
EXT HDMI interface. Used for providing one channel of 1PPS+TOD clock signals to the CC board in
the shelf.
REF Reserved.
DLINK0 HDMI interface. Used for providing two channels of output 1PPS+TOD clock signals to the CC
board in other shelves.
DLINK1 HDMI interface. Used for providing two channels of output 1PPS+TOD clock signals to the CC
board in other shelves.
FA 1 Fan module
End A is used for connecting the eRRU, and end B is used for
connecting the ZXSDR B8200 TL200.
The dry contact cable is used to connect the ZXSDR B8200 TL200
to an external monitoring device, and thus receive dry contact
data from the external device or send dry contact data to the
external device.
External view of a dry contact cable
eNodeB Overview
ZXSDR B8200 L200 Hardware Structure
ZXSDR R8882 Hardware Structure
ZXSDR eNodeB Maintenance
Position of the ZXSDR R8882 in the Radio
Network
R8882 2x60 W
Index Specification
Dimensions 480 mm x 320 mm x 150 mm
(H x W x D)
Weight 23 kg
Power Supply –48 V DC (–57 V DC to –37 V DC)
Grounding In practical applications, the grounding resistance must be less than
10 Ω.
Temperature -40℃ to +55℃
Humidity 10%–100%
Item Specification
eNodeB Overview
ZXSDR B8200 L200 Hardware Structure
ZXSDR R8882 Hardware Structure
ZXSDR eNodeB Maintenance
Operation And Maintenance
Measuremen
t Task
Management
Performance
Management
Performance
Performance
Data
Report
Management
Performance
Graphic
Analysis
Monitor
equipment
Fault
managem
ent
Multiple
Faults
alarming
oriented
methods
Configuration Management
• NE data configuration
• Data download/upload
• Data comparison
• Data output/input
• Data audit
• Dynamic data management
• Time synchronization
Security
log
Log
managem
ent
System Operation
log log
login
authentica
tion
Security operation
Specifies
manage authentica
the roles
ment tion
Ensures the
legitimacy
of the
operation
RRU OAM
• The ZXSDR R8972 configures RRU in accordance
with configuration data, forwards RRU’s
management commands from the NetNumen
U31, and collects RRU’s alarm and performance
information.
SON Functions
• SON functions can help perform some network
planning, configuration, optimization, and
healing processes automatically, and lower OPEX
by reducing manual involvement in such tasks.