Professional Documents
Culture Documents
AE905A
AE905B
AE905C
Y Posturefit
Mechanism
How to assemble to
Parts Included
your chair
For more information about our products and services or to see a list of dealers, please visit us at
www.hermanmiller.com/product-instructions or call 888 - 443 - 4357. Used on chairs Used on chairs C Screw (1)
© 2015 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. 1b0kgb - L. produced after to produced prior to E Applique (1)
1/11/2014 (1) 1/11/2014 (1)
® Y and Aeron are among the registered trademarks of Herman Miller, Inc.
A Clip
Notice:
Some of the parts have been wrapped to protect them during shipping. Remove the plastic
wrap before assembling the chair.
1.1 If chair is equipped with lumbar, slide off from back frame and dispose of properly.
Lumber
Back Frame
© 2014 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A on recycled paper.
® Y, Herman Miller and Aeron are among the registered trademarks of Herman Miller, Inc.
Step 2
Back Frame
2.1 Remove bottom middle screw from back frame and dispose of properly. For chairs
manufactured with torx head screw, use T-15 torx head screwdriver. For chairs
manufactured with hex head screw, use 2.5 MM hex head driver. For chairs manufactured
with phillips head screw, use #2 phillips head screwdriver.
NOTICE!
Using drill and 1/8” drill bit, to drill through bottom middle screw hole in
back frame, prior to installing clip, is an optional alternative to driving screw
Bottom Middle
through seat frame. Screw
Clip
Mounting Hole
! WARNING
It is important to secure clip tightly against back frame or product damage
will occur.
2.2 Place clip (A) over back frame aligning mounting hole to screw hole on back frame.
Drive replacement screw (C) through clip (A) and back frame, using #2 phillips head
screw driver. Screw (C) head should be flush with clip (A) when properly seated or product Mounting Hole
damage will occur. Screw torque should equal 20 in-lbs +/-2.
Replacement Screw
Clip
Step 3 Step 4
3.1 Place control mechanism (B) with mounting bracket, approximately (1) inch back from seat 4.1 Slide mounting brackets back on support casting until they wedge in place. Tighten screw
mount on right hand support casting. Hook on opposing half of mounting bracket and and torque to 6 in lb. +/-2.
install phillips head screw half way in, using #2 phillips head screwdriver. Do not tighten
4.2 Route cable from control mechanism (B) under support casting and between pneumatic
bracket to support casting at this time.
cable out over top of tilt and back towards back frame.
Pneumatic
Cable
Tilt
Seat
Mount
Cable Route
Mounting Bracket
Cable
Control Mechanism Route Right Hand
Support Casting
Mounting
Brackets
Support
Casting
5.1 Adjust control mechanism COUNTERCLOCKWISE, so control is at minimum setting. 6.1 Adjust Control mechanism COUNTERCLOCKWISE, so control is at minimum setting.
5.2 Carefully insert no.2. pencil tip into pellicle to create an opening in weave, where cable tip 6.2 Slide wishbone/postural support pad (D) onto back frame.
will pass through, then remove pencil.
6.3 Depress base of wishbone and place cable end in keyhole slot in wishbone.
5.3 Slide cable receiver towards cable tip and install into clip (A) while inserting cable tip
6.4 Adjust control mechanism clockwise to fully seat cable sleeve into cable receiver.
through pellicle opening.
5.4 Slide cable sleeve into cable receiver. Back Frame Ear
Wishbone / Postural
support Pad
#2 Pencil Tip
Wishbone
Cable Receiver
Keyhole Slot
Pellicle
Clip
Cable End
Cable Tip
Cable Sleever
Clip
Step 7
7.2 At rear center of seat, slide seat frame applique (E) over back of seat frame, as noted, so
that notch straddles installed posture fit cable.
7.3 Engage long (upper) formed edge of applique onto top rim of seat frame and roll applique
around behind seat frame. Snap formed edges, on each side of notch, onto lower seat
frame rim, on underside of seat.
Notch
Applique
Step 2 Step 3
2.1 Locate clip indentations. If chair doesn’t have indentations go to instructions for 3.1 Install cable clip by first centering the “hook” feature below the bottom back screw,
chairs manufactured before 1/11/2014. then pressing and rotating clip into position.
3.2 Cable clip must be centered on the bottom of the chair back for proper engagement.
Cable Clip
Step 4 Step 5
4.1 While holding the cable clip firmly in position, insert pencil through back fabric, inline with 5.1 Reinstall Posturefit lumbar assembly by sliding open slots on wishbone, down onto inner
cable mounting hole in cable clip, to create an opening in fabric. Then remove pencil slide rails on chair back frame. If necessary, use rubber mallet to ensure lumbar assembly
from fabric. See step 4-A. is completely seated onto slide rails. See step 5-A.
4.2 Route end of control cable under seat, making sure cable is routed over top all other 5.2 Adjust control mechanism counter-clockwise to set posturefit at minimum support setting.
control cables under seat.
5.3 Depress base of wishbone on Posturefit lumbar assembly, and engage cable end into
4.3 From back side of clip, insert end of control cable through cable clip mounting hole and keyhole slot in wishbone. See step 5-B.
through hole in fabric. See step 4-B.
Posturefit Lumbar
4.4 Insert control cable grommet into back side of cable clip and seat grommet completely into Assembly Wishbone
Pencil
Inner Slide Rail
Keyhole slot
Wishbone
Step 4-B
Cable Clip
6.2 At rear center of seat, slide seat frame applique (E) over back of seat frame, as noted, so
that notch straddles installed posture fit cable.
6.3 Engage long (upper) formed edge of applique onto top rim of seat frame and roll applique
around behind seat frame. Snap formed edges, on each side of notch, onto lower seat
frame rim, on underside of seat.
Notch
Applique