Professional Documents
Culture Documents
10113-1:1993
Hot-rolled products in
weldable fine grain
structural steels —
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
UDC 669.14.018.29.018.62-122.4-4:620.1
BS EN 10113-1:1993
Cooperating organizations
Contents
Page
Cooperating organizations Inside front cover
National foreword ii
Foreword 2
Text of EN 10113-1 3
National annex NA (informative) Committees responsible Inside back cover
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
© BSI 12-1998 i
BS EN 10113-1:1993
National foreword
This British Standard has been prepared under the direction of the Iron and Steel
Standards Policy Committee and is the English language version of
EN 10113-1:1993 Hot rolled products in weldable fine grain structural steels —
Part 1: General delivery conditions, published by the European Committee for
Standardization (CEN).
Together with BS EN 10113-2, BS EN 10113-3 and BS EN 10155, it partially
supersedes BS 4360:1990 which will be withdrawn in due course.
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
the EN title page, pages 2 to 16, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on
the inside front cover.
ii © BSI 12-1998
EUROPEAN STANDARD EN 10113-1
NORME EUROPÉENNE
EUROPÄISCHE NORM March 1993
UDC 669.14.018.29.018.62-122.4-4:620.1
Descriptors: Iron and steel products, hot-rolled products, structural steels, welded construction, delivery, designation, quality classes,
chemical composition, grades, quality, mechanical properties, inspection, tests, marking
structural steels —
Part 1: General delivery conditions
CEN
European Committee for Standardization
Comité Européen de Normalisation
Europäisches Komitee für Normung
Foreword Page
7 Technical requirements 5
This European Standard has been drawn up by
7.1 Steel manufacturing process 5
ECISS/TC 10 “Structural Steel — qualities” whose
Secretariat is held by NNI. 7.2 Delivery condition 5
This European Standard replaces 7.3 Chemical composition 5
EURONORM 113-72 Special quality weldable 7.4 Mechanical properties 6
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
2 © BSI 12-1998
EN 10113-1:1993
European Standard specifies the delivery conditions references, subsequent amendments to or revisions
for normalized steels in the grades and qualities of any of these publications apply to this European
given in Table 1 (chemical composition) and Table 3 Standard only when incorporated in it by
and Table 4 (mechanical properties) of Part 2. amendment or revision. For undated references the
NOTE Whenever normalized is mentioned, normalized rolled is latest edition of the publication referred to applies.
also covered (see 7.2 of Part 2). 2.1 General standards
Part 3 of this European Standard specifies the
delivery conditions for thermomechanical rolled EN 10020, Definition and classification of grades of
steels in the grades and qualities given in Table 1 steel.
(chemical composition) and Table 3 and Table 4 EN 10027-1, Designation systems for steel —
(mechanical properties) of Part 3. Part 1: Steel names principal symbols.
The steels specified in this European Standard are EN 10027-2, Designation systems for steel —
especially intended for use in heavily loaded parts of Part 2: Numerical system.
welded structures such as, bridges, flood gates, EN 10079, Definitions of steel products.
storage tanks, water supply tanks, etc., for service EN 10163, Delivery requirements for surface
at ambient and low temperatures. condition of hot-rolled steel plates, wide flats and
1.2 This European Standard does not apply to sections — Part 1: General requirements;
products for which other EURONORMS exist or Part 2: Plates and wide flats; Part 3: Sections.
European Standards dealing with steels for general EN 10204, Metallic products — Types of inspection
structural applications are being prepared: documents.
— Hot-rolled products of non-alloy structural EN 10021, General technical delivery requirements
steels (see EN 10025). for steel and iron products.
— Semi-finished products for forging in general prEN 100521), Vocabulary of heat treatment terms
purpose structural steels (see EURONORM 30). for ferrous products.
— Weathering steels for structural purposes EURONORM 162 (1981)2), Cold-rolled sections —
(see EN 10155). Technical conditions of delivery.
— Plates and wide flats made of weldable EURONORM 168 (1986)2), Iron and steel
fine-grained structural steels in the quenched products — Inspection documents — Contents.
and tempered condition (see prEN 10137).
ECCS IC 2 (1983)2), Weldable fine-grained
— Flat products in high yield strength steels for structural steels — Recommendations for
cold forming — wide flats, sheet/plate, wide and processing, in particular for welding.
narrow strip (see prEN 10149).
ECISS IC 10, Designation systems for steel —
— Steels for shipbuilding — normal and high Additional symbols for steel names.
strength qualities (see EURONORM 156).
2.2 Standards on dimensions and tolerances
— Hot finished structural hollow sections
(see prEN 10210-1). EN 10029, Hot-rolled plates 3 mm thick or above —
Tolerances on dimensions, shape and mass.
EN 10051, Continuously hot-rolled uncoated sheet
and strip of non-alloy and alloy steels — Tolerances
on dimensions and shape.
prEN 100341), Structural steel I and H sections —
Tolerances on shape and dimensions.
prEN 10056-21), Structural steel equal and unequal
leg angles — Tolerances on shape and dimensions.
1)
Draft is under discussion.
2)
Until these EURONORMS are transformed into European Standards, they can either be implemented or reference made to
the corresponding national standards, the list of which is given in Annex B to this European Standard.
© BSI 12-1998 3
EN 10113-1:1993
3)
Until these EURONORMS are transformed into European Standards, they can either be implemented or reference made to
the corresponding national standards, the list of which is given in Annex B to this European Standard.
4)
EURONORM 56 and 57 are added because they contain the nominal dimensions.
4 © BSI 12-1998
EN 10113-1:1993
NOTE 2 Thermomechanical rolling leading to the delivery — with specified minimum values of impact
condition M can include processes with an increasing cooling rate energy at temperatures not lower than – 20 °C;
with or without tempering including self-tempering but
excluding direct quenching and quenching and tempering. — with specified minimum values of impact
energy at temperatures not lower than – 50 °C.
4 Information to be supplied by the 6.2 Designation
purchaser
6.2.1 For the steel grades covered by this European
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
© BSI 12-1998 5
EN 10113-1:1993
7.3.2 The values for the chemical composition as 7.4.2.2 If agreed at the time of the enquiry and order
specified in Parts 2 and 3 of this European Standard another temperature (as given in Table 4 and
are the permitted limits or ranges, between which Table 5 of Parts 2 and 3) can be agreed.
the various steel grades are delivered. The Option 4.
manufacturer shall inform the purchaser at the
7.4.2.3 If agreed at the time of the enquiry and order
time of the enquiry and order which of the alloying
transverse impact values as given in Table 5 of
elements appropriate to the steel grade required
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
5)
Will be transformed into EN .. Recommendations for arc welding of ferritic steels.
6 © BSI 12-1998
EN 10113-1:1993
7.6.1 Strip 8.4.1 For ladle analysis determined for each cast,
the values reported by the manufacturer shall
The surface condition shall not impair an apply.
application appropriate to the steel grade if
8.4.2 Product analysis shall be carried out if agreed
adequate processing of the strip is applied.
at the time of the enquiry and order. The purchaser
7.6.2 Plates, wide flats and long products shall specify the number of samples and the
EN 10163 applies for the permissible surface elements to be determined.
discontinuities and for the repair of surface defects Option 3.
by grinding and/or welding. 8.5 Mechanical tests
Unless otherwise agreed previously with the
8.5.1 Preparation of samples
purchaser repair by welding is not allowed.
Option 8. 8.5.1.1 The following samples shall be taken from
one sample product of each test unit:
7.7 Internal defects
— one sample for tensile testing;
The products shall be free from internal defects — one sample sufficient for one set of six impact
which would exclude them from being used for the
test pieces.
usual purpose. Ultrasonic testing may be agreed at
the time of the enquiry and order (see 8.6.3). 8.5.1.2 The sample product can be any product
within the test unit.
Option 13 (for flat products).
8.5.1.3 For plates, sheet, wide strip and wide flats
Option 16 (for long products). the samples shall be taken approximately midway
between the edge and centre line of the products.
For wide strip the sample shall be taken at an
adequate distance from the end of the coil.
© BSI 12-1998 7
EN 10113-1:1993
For narrow strip (< 600 mm wide) the sample shall 8.6.2 Mechanical tests
be at an adequate distance from the end and at one Mechanical tests shall be carried out in the
third of the width. temperature range 10 °C to 35 °C, except where a
8.5.1.4 For long products EURONORM 18 shall specific temperature is specified for impact tests
apply (see Annex A). (see 7.4.2.1 and 7.4.2.2).
8.5.2 Preparation of test pieces 8.6.2.1 Tensile tests
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
8 © BSI 12-1998
EN 10113-1:1993
© BSI 12-1998 9
EN 10113-1:1993
C # 0,20 + 0,02
Si # 0,60 + 0,05
Mn # 1,70 – 0,05
+ 0,10
P # 0,035 + 0,005
S # 0,030 + 0,005
Nb # 0,05 + 0,010
V # 0,20 + 0,02
Ti # 0,05 + 0,01
Cr # 0,30 + 0,05
Ni # 0,80 + 0,05
Mo # 0,20 + 0,03
Cu # 0,35 + 0,04
> 0,35 # 0,70 + 0,07
N # 0,025 + 0,002
Altotal $ 0,02 – 0,005
10 © BSI 12-1998
EN 10113-1:1993
Annex A (normative)
Location of samples and test pieces (see EURONORM 18)
The following three categories of products are covered:
— beams, channels, angles, T sections and Z sections (Figure A.1)
— bars (Figure A.2)
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
© BSI 12-1998 11
EN 10113-1:1993
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
12 © BSI 12-1998
EN 10113-1:1993
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
© BSI 12-1998 13
EN 10113-1:1993
Annex B (informative)
List of national standards which correspond to EURONORMS referenced
Until the following EURONORMS are transformed into European Standards, they may be either
implemented or reference made to the corresponding national standards as listed in Table B.1.
Table B.1 — EURONORMS with corresponding national standards
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
14 © BSI 12-1998
EN 10113-1:1993
© BSI 12-1998 15
EN 10113-1:1993
Annex C (informative)
List of corresponding former designations
Table C.1 — List of corresponding former designations
Designation Equivalent former designations in
16 © BSI 12-1998
BS EN 10113-1:1993
Committees responsible
The United Kingdom participation in the preparation of this European Standard was entrusted by the Iron
and Steel Standards Policy Committee (ISM/-) to Technical Committee ISM/12 upon which the following
bodies were represented:
BEAMA Ltd.
British Constructional Steelwork Association Ltd.
British Railways Board
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
Cross-references
The British Standards corresponding to the European Standards referred to in the text are identical in
number and title with those given in clause 2.
© BSI 12-1998
|
|
|
|
|
|
|
|
|
BSI Ð British Standards Institution
|
|
|
|
|
|
| BSI is the independent national body responsible for preparing British Standards. It
|
| presents the UK view on standards in Europe and at the international level. It is
| incorporated by Royal Charter.
|
|
| Revisions
|
|
| British Standards are updated by amendment or revision. Users of British Standards
|
| should make sure that they possess the latest amendments or editions.
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
|
|
| It is the constant aim of BSI to improve the quality of our products and services. We
|
| would be grateful if anyone finding an inaccuracy or ambiguity while using this
| British Standard would inform the Secretary of the technical committee responsible,
|
| the identity of which can be found on the inside front cover. Tel: 020 8996 9000.
|
| Fax: 020 8996 7400.
|
|
| BSI offers members an individual updating service called PLUS which ensures that
|
| subscribers automatically receive the latest editions of standards.
|
|
| Buying standards
|
| Orders for all BSI, international and foreign standards publications should be
|
| addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
|
|
| In response to orders for international standards, it is BSI policy to supply the BSI
|
| implementation of those that have been published as British Standards, unless
|
| otherwise requested.
|
|
| Information on standards
|
| BSI provides a wide range of information on national, European and international
|
| standards through its Library and its Technical Help to Exporters Service. Various
|
| BSI electronic information services are also available which give details on all its
|
| products and services. Contact the Information Centre. Tel: 020 8996 7111.
|
| Fax: 020 8996 7048.
|
|
| Subscribing members of BSI are kept up to date with standards developments and
| receive substantial discounts on the purchase price of standards. For details of
|
| these and other benefits contact Membership Administration. Tel: 020 8996 7002.
|
| Fax: 020 8996 7001.
|
|
| Copyright
|
|
| Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of
|
| the publications of the international standardization bodies. Except as permitted
| under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,
|
| stored in a retrieval system or transmitted in any form or by any means ± electronic,
|
| photocopying, recording or otherwise ± without prior written permission from BSI.
|
|
| This does not preclude the free use, in the course of implementing the standard, of
|
| necessary details such as symbols, and size, type or grade designations. If these
|
| details are to be used for any other purpose than implementation then the prior
| written permission of BSI must be obtained.
|
|
| If permission is granted, the terms may include royalty payments or a licensing
|
| agreement. Details and advice can be obtained from the Copyright Manager.
|
| Tel: 020 8996 7070.
|
|
|
|
|
|
|
|
|
BSI |
|
389 Chiswick High Road |
|
London |
|
W4 4AL |
|
|
|
|
|
|