Professional Documents
Culture Documents
Over-tighteningflare-type (unionnuttype) metalpartsmaynot: Tiph十pninp クR+nl R+∩仁 R+nR
Over-tighteningflare-type (unionnuttype) metalpartsmaynot: Tiph十pninp クR+nl R+∩仁 R+nR
UE
●
CleanalltubesandhoseswithcleanlngSOlvent,anddrywitbair.
1.F一丁TING FLARE一丁YPEJOINT
Over-tighteningflare-type(unionnuttype)metalpartsmaynot only damagenuts or
●
SeatSurfaces,butmayalsopreventoptimumsealingbylinecontact,CauSlngOilleak.
∪[it:kgf・m(lb・冊)
Nomi[al
1/4” 3/8” 1/2”
Pipe Size
th「eads Tiph十pninp
lI⊂〉l卜しヽ′lllll⊂)
クR+nl
t__●ヽノ ■_i..■ ヽノ●ヽノ
R+∩仁
ヽノ __i......ヽノ●ヽノ
R+nR
ヽ′ _⊥.._ ヽ′●ヽノ
Nomi[aI
3/4” 1” ト1/4” ト1/2” 2”
Pipe Size
th「eads Tighte[i[g 12±1.2 14±1.4 1了±1.了 21±2.1 42±4.2
to「que (86.8±8.7) (101±10) (123±12) (152±15) (304±30)
Th「ead
7/8”-14 1-1/16”-12 1-5/16”-12 1-5/8”-12
∪[ified Size
th「eads Tighte[i[g 6±0.6 2±0.2 14±1.4 1了±1.7
to「q]e (43.4±4.3) (14.5±1.4) (101±10) (123±12)
2.F汀TING N2(NYLON)TUBEJO】NTS
Plastic sleeve
Insertthetubesecurel)7intothefitting,andturnthenutapproximatelyl-1/4turnswith
aspannerfromthepositionwherethenutisfullyscrewedinwithhand.
ー297-
3.TIGHTENING FLARELESSJOINTS
l)Preliminaryassembly(pre-Setting)
l
Toconnectdirectlyplpeandjointsby Cutthepipeasclose
hand,prOCeedasfollows: toa rightan9leas
POSSibIeandchamfer
(1)Insertthenut,andthenthesleevecut- ●
SlightIythecutend.
ting edgeinto the plpe tOWard the
●
plpeends.
St eeVe
Connector N臼t
(2)Insertthepipeintotheconnector,and Lubricate
B
●
bottom(B)oftheconnector.
(Besuretolubricate thecontacting
andturningparts.)
(3)Tightenthenutwithaspannerwhile
● ●
turnlngtheplpeWiththeotherhand. P‖oted9e
●
WhentheplpeCannOtbeturnedany
●
(Markalineonthepoint.)Atthis
pointthesleevegripsthepipe・The
point(wherethesleeァe'scuttingedge
startsgrippingtheplpe)iscalledthe
●
grlppOint.
(4)Byturningthenutl-1/4tol-1/2turns
from the grip point position,the
譜2慧ぷ宍よ払)
Sleeve'scuttingedgewillcompletely
●
●
grlptheplpe.
■■
 ̄十- ヽ
-
■-
ヽ
一 ●●-′
一●▼●
、 ヽ■
ヽi _
上せ一丁 ̄
ト1/4toト1/2turn
Procedures(1)through(4)abovearecalledthepreliminaryassembly(pre-Setting). ●
benchinordertogrlpthesleeve.
2)Reassembly(resetting) ●
Toinstallthepre-SetpleCeStOthemachine,prOCeedasfo110WS:
(1)Setthepresetpieceonthemachineandtightentbenut,Whileturningthepipebyband,
untilthetighteningtorquevaluerapidlyincreases(sharptorquerisepoint).
(2)Giveanotherl/4turn(1/./3turnifneeded)fromthesharptorquerisepoint.
-298-